Currently, If STA doesn't send beacon report response to
AP, AP will not be able to know the reason why sta did not
send beacon report as no reason code is defined in
IEEE802.11-2016 standard.
Fix is to add Optional IE in Beacon Report Response which will be
populated based on err code and beacon_report_error_vsie ini.
Change-Id: I91ab0cdfadbe903bdc3085a94b38938a35b693e0
CRs-Fixed: 2614385
Currently, the driver schedules the message to set
power save enable/disable to FW as part of the
set power mgmt command received from the userspace.
This command is then scheduled and is sent via
the scheduler thread.
Generally, userspace sets the power save disable
when it starts the DHCP process and enables the
power save back when the DHCP is completed.
DHCP packets are sent through the Datapath and the
PS enable/disable command would be sent via the
control path explained above.
the Race could happen that the scheduler was busy
with some other task and the PS disable command
was in the queue and the DHCP process began.
This would result in DHCP packets going to the peer
with PS enabled.
The fix is to set the power save enable/disable directly
instead of using the scheduler path.
Change-Id: I0f2aed37f875c283f318fb44bcc40d0ab401413a
CRs-Fixed: 2611480
Reset roam configurations to default while station mode init.
Thus user gets default roam configuration with which STA mode is
initialized.
example: When STA connect to AP, user queries for default roam
scan home away time using following command of wpa_cli.
$wpa_cli
>driver GETSCANHOMEAWAYTIME
<OUTPUT is default value of gRoamScanHomeAwayTime INI>
Change-Id: If525e4a92fee6f4823996c1e1e34b9943fed0432
CRs-Fixed: 2607557
Firmware advertises service capability bit
WMI_SERVICE_PEER_DELETE_NO_PEER_FLUSH_TIDS_CMD
when peer delete command takes care of flush
all tids functionality.
If this service bit is set advertised by FW
then host does not need to send the flush tid
command before sending the peer delete command.
Change-Id: I7838b1d0465fefd58eb8faf1d2d87beccf55134b
CRs-Fixed: 2609964
As part of new requirement WLAN subsystem needs to perform thermal
mitigation action as per the thermal state of the device. The
wifi hal sends vendor command QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD
with the thermal level parameter and wlan host performs the required
appropriate action. wlan host driver maps the thermal level to
corresponding duty cycle off percent value and duty cycle value,
send WMI_THERM_THROT_SET_CONF_CMDID cmd to FW.
Make changes to perform vendor command handling, mapping thermal level
to duty cycle value and communicating the thermal information to FW.
change-ID: I77175048c817ab755cdb838018e414ef3ee0b112
CRs-Fixed: 2610395
To set specific channels, user give SETROAMSCANCHANNELS command with
channel count followed by number of channels.
Ex. SETROAMSCANCHANNELS 2 1 11, here 2 is count and 1 & 11 are the
channels.
If channel count is more than the number of channels, driver rejects
SETROAMSCANCHANNELS command and if number of channels are more than
the channel count, driver ignores excess channels in the list.
Change-Id: I276b84b4994bdf25abf36298dc212dcd54ce0dbb
CRs-Fixed: 2609788
In the function hdd_sendactionframe, the parameters passed include the
payload and the corresponding payload length; payload being generic
pointer. The payload is then typecasted into the destination structure
of type tpSirMacVendorSpecificFrameHdr. If the size of the payload
specified in payload_len is less than the size of the destination
structure, there is possiblility of OOB read while accessing the same.
To prevent this security vulnerability, add a sanity check for the
payload_len against the size of the destination structure.
Change-Id: Ib0e7b7bfcf78412d81f18cf887e5296d80272598
CRs-Fixed: 2517858
Add a new INI parameter "nan_separate_iface_support" to
indicate firmware that the host driver supports separate
interface for NAN Discovery.
Change-Id: I6fb313b02c5f3a05638e85494051fb003b2dd867
CRs-Fixed: 2612006
Currently, the driver rejects the roam stats event if any of the
roam trigger or roam scan or roam results tlv is not present.
Now the firmware will send neighbor report immediately after the
neighbor report response is received from AP instead of buffering
it.
So, handle roam stats event with neighbor report tlv alone and no
other tlv is present. Also update documentation for some static
functions
Change-Id: I8a697cda9945a7611930823dd7515bc36223f32a
CRs-Fixed: 2610358
In FTM mode, no peer is created in the host. Currently, since
peer_unmap_conf_support feature is enabled, FW is expecting
WMA_SEND_PEER_UNMAP_CONF from host to remove the peer Id from AST.
But host never send this WMI CMD in FTM mode.
Disable peer_unmap_conf_support in FTM mode which allow FW to
delete the peer Id without any WMI CMD expectation from host.
Change-Id: Idf9082adc81187346563f3aedf1f1657164f03cc
CRs-Fixed: 2608929
wlan_hdd_pm_qos_notify() is currently directly calling the kernel runtime
pm operation functions. Use the hif api functions to perform these
operations instead.
Change-Id: I8b13a8dd0d5a89f2208b4f319e71b4ffc217ae5c
CRs-Fixed: 2607715
arp_ns_offload and gtk offload command are being issued for NaN mode
vdev. NaN mode vdev does not support ARP_NS and GTK off load features,
so disable them when in NaN mode.
Change-Id: Iab11c92bb5da4004b62e642342a386f532832509
CRs-Fixed: 2608618
Instead of returning the whole valid channel list, just return the
PCL to QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST.
Change-Id: I2be4357f1c25732b9d1098f3d16259217fa46b8e
CRs-Fixed: 2607890
User can configure roam scan channels using SETROAMSCANCHANNELS and
ADDROAMSCANCHANNELS command.
As the result of GETROAMSCANCHANNELS command, driver returns the list
of channels configured by user.
Change-Id: I847215c8319f819f8db60690842ef50037fe6aaf
CRs-Fixed: 2610136
Below beacon report/NEIGH rpt related details needs to be logged into kmsg:
i. Beacon Report Request
1. Token, Class, Channel list, Duration, Mode, BSSID wildcard, SSID
ii. Beacon Report Response
1. Token, Scanned AP Number
2. Reason – If Beacon Report could not proceed.
iii. Neighbor Report request
1. Sent from Mobile
iv. Neighbor Report Response
1. Channel list
Add the required details in beacon/neighbor report TX/RX path
Change-Id: I719863ecd4ac607d65dbbfde806921fe7214ce10
CRs-Fixed: 2610596
Driver/firmware may not support NAN in some platforms. But when
framework tries to enable NAN/NDP, driver returns an error and
logs the failure with error level. This is causing excessive
logs in dmesg. Reduce the log level to debug in order to avoid
spamming dmesg.
Change-Id: Ied8f06fadc3b68a9fc3657e31679b71a3807737e
CRs-Fixed: 2608564
User configures specific channel using SETROAMSCANCHANNELS command
and preferred channels using ADDROAMSCANCHANNELS command.
For roam scanning, "specific channels list" is preferred over
"preferred channel list". Hence if user configured specific channels
then block ADDROAMSCANCHANNLES command.
Change-Id: Ib4e2c9ed7ca1e44c0c7e287e2ac350c3d4f3540e
CRs-Fixed: 2610133
Add support to make event WMI_ROAM_PMKID_REQUEST_EVENTID as
wakable in FIPS case.
In FIPS Enabled case, for roaming Firmware sends PMKID request
to host as firmware is not supposed to do crypto functionality
with FIPS enabled.
Change-Id: I09b6b68f77ba75f9e5519ff18017c95d16771f52
CRs-Fixed: 2513790
