This patch adds client-side support to allow for callbacks other than
AUTH_SYS.
Signed-off-by: Olga Kornievskaia <aglo@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The rpc client needs to know the principal that the setclientid was done
as, so it can tell gssd who to authenticate to.
Signed-off-by: Olga Kornievskaia <aglo@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Two principals are involved in krb5 authentication: the target, who we
authenticate *to* (normally the name of the server, like
nfs/server.citi.umich.edu@CITI.UMICH.EDU), and the source, we we
authenticate *as* (normally a user, like bfields@UMICH.EDU)
In the case of NFSv4 callbacks, the target of the callback should be the
source of the client's setclientid call, and the source should be the
nfs server's own principal.
Therefore we allow svcgssd to pass down the name of the principal that
just authenticated, so that on setclientid we can store that principal
name with the new client, to be used later on callbacks.
Signed-off-by: Olga Kornievskaia <aglo@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Implement the new upcall. We decide which version of the upcall gssd
will use (new or old), by creating both pipes (the new one named "gssd",
the old one named after the mechanism (e.g., "krb5")), and then waiting
to see which version gssd actually opens.
We don't permit pipes of the two different types to be opened at once.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Keep a pointer to the inode that the message is queued on in the struct
gss_upcall_msg. This will be convenient, especially after we have a
choice of two pipes that an upcall could be queued on.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Introduce a global variable pipe_version which will eventually be used
to keep track of which version of the upcall gssd is using.
For now, though, it only keeps track of whether any pipe is open or not;
it is negative if not, zero if one is opened. We use this to wait for
the first gssd to open a pipe.
(Minor digression: note this waits only for the very first open of any
pipe, not for the first open of a pipe for a given auth; thus we still
need the RPC_PIPE_WAIT_FOR_OPEN behavior to wait for gssd to open new
pipes that pop up on subsequent mounts.)
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Keep a count of the number of pipes open plus the number of messages on
a pipe. This count isn't used yet.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
I can't see any reason we need to call this until either the kernel or
the last gssd closes the pipe.
Also, this allows to guarantee that open_pipe and release_pipe are
called strictly in pairs; open_pipe on gssd's first open, release_pipe
on gssd's last close (or on the close of the kernel side of the pipe, if
that comes first).
That will make it very easy for the gss code to keep track of which
pipes gssd is using.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We want to transition to a new gssd upcall which is text-based and more
easily extensible.
To simplify upgrades, as well as testing and debugging, it will help if
we can upgrade gssd (to a version which understands the new upcall)
without having to choose at boot (or module-load) time whether we want
the new or the old upcall.
We will do this by providing two different pipes: one named, as
currently, after the mechanism (normally "krb5"), and supporting the
old upcall. One named "gssd" and supporting the new upcall version.
We allow gssd to indicate which version it supports by its choice of
which pipe to open.
As we have no interest in supporting *simultaneous* use of both
versions, we'll forbid opening both pipes at the same time.
So, add a new pipe_open callback to the rpc_pipefs api, which the gss
code can use to track which pipes have been open, and to refuse opens of
incompatible pipes.
We only need this to be called on the first open of a given pipe.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
I want to add a little more code here, so it'll be convenient to have
this flatter.
Also, I'll want to add another error condition, so it'll be more
convenient to return -ENOMEM than NULL in the error case. The only
caller is already converting NULL to -ENOMEM anyway.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We'll want to call this from elsewhere soon. And this is a bit nicer
anyway.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We're just about to kfree() gss_auth, so there's no point to setting any
of its fields.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
There's a bit of a chicken and egg problem when it comes to destroying
auth_gss credentials. When we destroy the last instance of a GSSAPI RPC
credential, we should send a NULL RPC call with a GSS procedure of
RPCSEC_GSS_DESTROY to hint to the server that it can destroy those
creds.
This isn't happening because we're setting clearing the uptodate bit on
the credentials and then setting the operations to the gss_nullops. When
we go to do the RPC call, we try to refresh the creds. That fails with
-EACCES and the call fails.
Fix this by not clearing the UPTODATE bit for the credentials and adding
a new crdestroy op for gss_nullops that just tears down the cred without
trying to destroy the context.
The only difference between this patch and the first one is the removal
of some minor formatting deltas.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Hi.
I've been looking at a bugzilla which describes a problem where
a customer was advised to use either the "noac" or "actimeo=0"
mount options to solve a consistency problem that they were
seeing in the file attributes. It turned out that this solution
did not work reliably for them because sometimes, the local
attribute cache was believed to be valid and not timed out.
(With an attribute cache timeout of 0, the cache should always
appear to be timed out.)
In looking at this situation, it appears to me that the problem
is that the attribute cache timeout code has an off-by-one
error in it. It is assuming that the cache is valid in the
region, [read_cache_jiffies, read_cache_jiffies + attrtimeo]. The
cache should be considered valid only in the region,
[read_cache_jiffies, read_cache_jiffies + attrtimeo). With this
change, the options, "noac" and "actimeo=0", work as originally
expected.
This problem was previously addressed by special casing the
attrtimeo == 0 case. However, since the problem is only an off-
by-one error, the cleaner solution is address the off-by-one
error and thus, not require the special case.
Thanx...
ps
Signed-off-by: Peter Staubach <staubach@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We've never considered the sunrpc code as part of any ABI to be used by
out-of-tree modules.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Somehow, this escaped the previous purge. There should be no need to keep
any extra locks in the XDR callbacks.
The NFS client XDR code only writes into private objects, whereas all reads
of shared objects are confined to fields that do not change, such as
filehandles...
Ditto for lockd, the NFSv2/v3 client mount code, and rpcbind.
The nfsd XDR code may require the BKL, but since it does a synchronous RPC
call from a thread that already holds the lock, that issue is moot.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'for-2.6.28' of git://linux-nfs.org/~bfields/linux:
NLM: client-side nlm_lookup_host() should avoid matching on srcaddr
nfsd: use of unitialized list head on error exit in nfs4recover.c
Add a reference to sunrpc in svc_addsock
nfsd: clean up grace period on early exit
The svc_addsock function adds transport instances without taking a
reference on the sunrpc.ko module, however, the generic transport
destruction code drops a reference when a transport instance
is destroyed.
Add a try_module_get call to the svc_addsock function for transport
instances added by this function.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Tested-by: Jeff Moyer <jmoyer@redhat.com>
Fix a regression reported by Max Kellermann whereby kernel profiling
showed that his clients were spending 45% of their time in
rpcauth_lookup_credcache.
It turns out that although his processes had identical uid/gid/groups,
generic_match() was failing to detect this, because the task->group_info
pointers were not shared. This again lead to the creation of a huge number
of identical credentials at the RPC layer.
The regression is fixed by comparing the contents of task->group_info
if the actual pointers are not identical.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have to be careful when we try to unhash the credential in
put_rpccred(), because we're not holding the credcache lock, so the call to
rpcauth_unhash_cred() may fail if someone else has looked the cred up, and
obtained a reference to it.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We need to make sure that we don't remove creds from the cred_unused list
if they are still under the moratorium, or else they will never get
garbage collected.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the server sends us an RST error while we're in the TCP_ESTABLISHED
state, then that will not result in a state change, and so the RPC client
ends up hanging forever (see
http://bugzilla.kernel.org/show_bug.cgi?id=11154)
We can intercept the reset by setting up an sk->sk_error_report callback,
which will then allow us to initiate a proper shutdown and retry...
We also make sure that if the send request receives an ECONNRESET, then we
shutdown too...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
ipv4: Add a missing rcu_assign_pointer() in routing cache.
[netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
xen-netfront: Avoid unaligned accesses to IP header
lmc: copy_*_user under spinlock
[netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA
Some code here depends on CONFIG_KMOD to not try to load
protocol modules or similar, replace by CONFIG_MODULES
where more than just request_module depends on CONFIG_KMOD
and and also use try_then_request_module in ebtables.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-2.6.28' of git://linux-nfs.org/~bfields/linux: (59 commits)
svcrdma: Fix IRD/ORD polarity
svcrdma: Update svc_rdma_send_error to use DMA LKEY
svcrdma: Modify the RPC reply path to use FRMR when available
svcrdma: Modify the RPC recv path to use FRMR when available
svcrdma: Add support to svc_rdma_send to handle chained WR
svcrdma: Modify post recv path to use local dma key
svcrdma: Add a service to register a Fast Reg MR with the device
svcrdma: Query device for Fast Reg support during connection setup
svcrdma: Add FRMR get/put services
NLM: Remove unused argument from svc_addsock() function
NLM: Remove "proto" argument from lockd_up()
NLM: Always start both UDP and TCP listeners
lockd: Remove unused fields in the nlm_reboot structure
lockd: Add helper to sanity check incoming NOTIFY requests
lockd: change nlmclnt_grant() to take a "struct sockaddr *"
lockd: Adjust nlmsvc_lookup_host() to accomodate AF_INET6 addresses
lockd: Adjust nlmclnt_lookup_host() signature to accomodate non-AF_INET
lockd: Support non-AF_INET addresses in nlm_lookup_host()
NLM: Convert nlm_lookup_host() to use a single argument
svcrdma: Add Fast Reg MR Data Types
...
Clean up the various different email addresses of mine listed in the code
to a single current and valid address. As Dave says his network merges
for 2.6.28 are now done this seems a good point to send them in where
they won't risk disrupting real changes.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RPC/RDMA connection logic could return early from reconnection
attempts, leading to additional spurious retries.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The RPC/RDMA code had a constant 5-second reconnect backoff, and
always performed it, even when re-establishing a connection to a
server after the RPC layer closed it due to being idle. Make it
an geometric backoff (up to 30 seconds), and don't delay idle
reconnect.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The send marshaling code split a particular dprintk across two
lines, which makes it hard to extract from logfiles.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add defensive timeouts to wait_for_completion() calls in RDMA
address resolution, and make them interruptible. Fix the timeout
units to milliseconds (formerly jiffies) and move to private header.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The RPC/RDMA code can leak RDMA connection manager endpoints in
certain error cases on connect. Don't signal unwanted events,
and be certain to destroy any allocated qp.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The xprt_connect call path does not expect such errors as ECONNREFUSED
to be returned from failed transport connection attempts, otherwise it
translates them to EIO and signals fatal errors. For example, mount.nfs
prints simply "internal error". Translate all such errors to ENOTCONN
from RPC/RDMA to match sockets behavior.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The RPC/RDMA protocol allows clients and servers to avoid RDMA
operations for data which is purely the result of XDR padding.
On the client, automatically insert the necessary padding for
such server replies, and optionally don't marshal such chunks.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
RDMA disconnects yield an upcall from the RDMA connection manager,
which can race with rpc transport close, e.g. on ^C of a mount.
Ensure any rdma cm_id and qp are fully destroyed before continuing.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
An RPC/RDMA client cannot retransmit on an unbroken connection,
doing so violates its flow control with the server.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This logic sets the connection parameter that configures the local device
and informs the remote peer how many concurrent incoming RDMA_READ
requests are supported. The original logic didn't really do what was
intended for two reasons:
- The max number supported by the device is typically smaller than
any one factor in the calculation used, and
- The field in the connection parameter structure where the value is
stored is a u8 and always overflows for the default settings.
So what really happens is the value requested for responder resources
is the left over 8 bits from the "desired value". If the desired value
happened to be a multiple of 256, the result was zero and it wouldn't
connect at all.
Given the above and the fact that max_requests is almost always larger
than the max responder resources supported by the adapter, this patch
simplifies this logic and simply requests the max supported by the device,
subject to a reasonable limit.
This bug was found by Jim Schutt at Sandia.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Acked-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Configure, detect and use "fastreg" support from IB/iWARP verbs
layer to perform RPC/RDMA memory registration.
Make FRMR the default memreg mode (will fall back if not supported
by the selected RDMA adapter).
This allows full and optimal operation over the cxgb3 adapter, and others.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Acked-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
At transport creation, check for, and use, any local dma lkey.
Then, check that the selected memory registration mode is in fact
supported by the RDMA adapter selected for the mount. Fall back
to best alternative if not.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Acked-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Refactor the memory registration and deregistration routines.
This saves stack space, makes the code more readable and prepares
to add the new FRMR registration methods.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Despite the fact that cloned rpc clients won't have the cl_autobind flag
set, they may still find themselves calling rpcb_getport_async(). For this
to happen, it suffices for a _parent_ rpc_clnt to use autobinding, in which
case any clone may find itself triggering the !xprt_bound() case in
call_bind().
The correct fix for this is to walk back up the tree of cloned rpc clients,
in order to find the parent that 'owns' the transport, either because it
has clnt->cl_autobind set, or because it originally created the
transport...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Basically, try_module_get here are pretty useless. Any other module using
this API will pin sunrpc in memory due using exported symbols.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The inititator/responder resources in the event have been swapped. They
no represent what the local peer would set their values to in order to
match the peer. Note that iWARP does not exchange these on the wire and
the provider is simply putting in the local device max.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
![](/avatar/5fc124e8ccd7b94d35e5c23f8c0b7c63?size=56 "\\"J. Bruce Fields\"){kind=small}
