Modules: NM256 driver
The current snd-nm256 driver can cause Dell Latitude CSx laptops to
lock-up during module (un)load. I have isolated this to the writes to
the control port register at offset 0x6cc which were not already
protected by the existing reset_workaround.
I tried grouping these writes with the existing reset_workaround
clause, but that caused the driver to have (un)load problems on the
Dell Latitude LS laptops. So, I have implemented a reset_workaround_2
clause (please feel free to suggest a better name!) to cover this
situation and added a quirk entry for the CSx laptops.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: YMFPCI driver
We better pretend that the ymfpci timer runs at 48 kHz because the
interrupt frequency cannot be higher, and clients that would try to
use 96 kHz would run at half their desired speed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Maestro3 driver
This patch fixes the maestro3 driver to call the snd_m3_assp_init
function to write the DSP firmware into the ASSP chip before sending the
RUN_ASSP command, thereby solving the hang after a cold boot.
Signed-off-by: Charles R. Anderson <cra@alum.wpi.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
- Set buggy_irq parameter before registration of irq handler.
- Clean up module parameter handling.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: VIA82xx driver
The change only affects the via823x kind of chips.
Here the via8233_pcm_pointer_hw() function
(named snd_via8233_pcm_pointer() before)
needed to loop until a non zero position is red from the chip.
Measurements have shown that more than 200 loops are typically needed on
an Athlon64.
As io-reads cost many cycles, those loops sum up huge.
via8233_pcm_pointer_hw() runs either in interrupt or with interrupts
disabled. So it introduces significant interrupt latency.
The patch introduces a calculated position value hwptr_done,
that is updated by the interrupt routine when a period is completed.
It is only used, if the 823x chip returns a zero position, which can't
be interpreted reliably.
Further optimisation is applied on the 8233 chip's interrupt routine:
Only the SGD_SHADOW is read, as it contains all infos needed.
We ommit ~5 more register reads that way.
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: VIA82xx driver
The patch enable separate DXS controls of sound function of VIA VT82xx
controller in case DXS volume is not needed for PCM Playback volume
control emulation.
Signed-off-by: Honza Maly <hkmaly@matfyz.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ES1938 driver
- Clean up the last PM fix
- Add TRIGGER_SUSPEND/RESUME to disable/enable DMA properly during PM
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ES1938 driver
This patch fixes the suspend/resume issue I'm having with ESS-Solo1
soundcard. Without this patch I might get after resume message
that kernel is disabling the IRQ5 (soundcard). If there was something
playing it wont continue after resume without this patch.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Remove vmalloc wrapper
- Add release_and_free_resource() to remove kfree_nocheck() from each driver
and simplify the code
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove snd_runtime_check() macro.
This macro worsens the readability of codes. They should be either
normal if() or removable asserts.
Also, the assert displays stack-dump, instead of only the last caller
pointer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
On my Acer Aspire 3003LCi laptop, the speaker volume is not controlled
by the master control, but by the headphone control. Enabling the
'hp_only' quirk corrects this. The patch below adds this device to the
list of known quirks.
Signed-off-by: Dick Streefland <dick@streefland.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ICE1724 driver
Remove the restcition of sample rates on Revolution 7.1 board.
This enables the low 8-44kHz sample rates.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the code for supporting eight cards from the integrated
controller drivers because There Can Be Only One controller of
each type per mainboard.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Sound Core,PCI drivers
AC97 Kconfig entries broke the ALSA device drivers menu,
so move them to a location where that won't happen,
enabling all device sub-menus to be presented together.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch cleans last ac97 audio/modem codec interception in
initialization procedures (ac97_mixer_new()) and removes obsolete
SHARED_TYPE 'locking' which prevents from AMC codecs to function
correctly.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: YMFPCI driver
This patch adds a new mixer control called 'IEC958 Loop' which makes
it possible to loop digital signals from S/PDIF-in to S/PDIF-out.
Signed-off-by: Glen Masgai <mimosius@gmx.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: CMIPCI driver
If possible, use ports in the card's PCI port address range instead of
the legacy ports.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: HDA Intel driver
This patch is to make the Intel HDA code work for NVIDIA azalia controller.
Modified by Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod G. <vinodg@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: EMU10K1/EMU10K2 driver
Adds left and right front channel outputs using fxbus 8 and 9 and 'Front'
playback and capture volume controls.
Signed-off-by: Mikael Magnusson <mikma@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds the magic IO wakeup code for the CardBus version of the
Creative Labs Audigy 2 to the snd-emu10k1 driver.
Without the magic IO enable sequence, reading from the IO region of the
card will fail spectacularly, and the machine will hang.
My next task will be getting the driver to actually play sound without
distortion.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
[ This is a work-in-progress, but since it avoids a total lockup
if the emu10k module is loaded on a machine with the cardbus
card inserted, we're better off with it than without it, even
if sound quality is bad right now ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EMU10K1/EMU10K2 driver
Fixed the handling of ac97_chip=2 capability type.
The error occurs in snd_ac97_mixer(), not in snd_ac97_bus().
Also, release the unnecessary ac97_bus object in the error path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
Fixed the error at loading SBLive Game board (and possible other models).
The PCI SSIDs of this board conflicts with SB Live 5.1 Platinum, which has
no AC97 chip.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Mark the ALC882 'LFE Playback Switch' as an input, like the other
playback switch settings.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Fix a typo (cut & paste) in the alc880_test_mixer structure.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
The ALC260 'Mono Playback Switch' is marked as an output in
patch_realtek.c. It actually does not work unless it is marked as an
input. Go figure... This was tested and confirmed on an HP xw4300.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
A single call to the driver suspend/resume method for each device is
enough. The level and SUSPEND_*/RESUME_* arguments are deprecated and
said to be removed eventually anyway (no other subsystem are using them
anymore except platform devices).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
Don't use dev.platform_data to store a reference to the containing
ac97_t structure. Such assignment is redundent since we can deduce the
ac97_t structure location from the contained device structure. This
sets platform_data free for other purposes.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
The bus_id is initialized with a generic identifier string which is not
really useful for proper driver matching. Let the driver decide what it
needs via its probe method instead.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Intel driver
Disable the auto-correction of DMA position temporarily.
It doesn't work as expected yet...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
No index is templated for si3036 modem controls.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While doing an allyesconfig build, I noticed that the commit
commit 8cdfd2519c
Author: Takashi Iwai <tiwai@suse.de>
Date: Wed Sep 7 14:08:11 2005 +0200
[ALSA] Remove superfluous PCI ID definitions
broke the RME32 and RME96 drivers, since the PCI IDs they use seem to have
changed names. Here's a patch to fix this -- compile tested only, since I
have no idea what the hardware even is.
Fix the build of the RME32 and RME96 drivers by having them use the
PCI_DEVICE_ID_RME_xxx names defined in <linux/pci_ids.h> instead of the
PCI_DEVICE_ID_xxx names that they used to define themselves.
Also fix the typo in the id PCI_DEVICE_IDRME__DIGI96_8_PAD_OR_PST so the
name is PCI_DEVICE_ID_RME_DIGI96_8_PAD_OR_PST.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Documentation,Intel8x0 driver
Added buggy_semaphore module option to snd-intel8x0 driver
for a workaround for hardwards with buggy codec semaphores.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver,HDA Intel driver,HDA generic driver
Assign audio PCMs first before modem PCMs.
The modem stream is assigned up to device #6, to be consistent over
different models.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Intel driver
Check the validity of the current DMA position when position_fix=0 (auto)
is set. If the DMA position overcomes the threshold, the driver changes
the fix behavior automatically to use POSBUF.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Add the subsystem PCI devid to the list (on top of 2.6.13).
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA Core,RawMidi Midlevel,ALSA<-OSS emulation,ALSA sequencer
RME32 driver,RME96 driver,EMU10K1/EMU10K2 driver,NM256 driver
Add sparse annotations where we do strange this with __iomem/__user
pointers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
CA0106 driver,EMU10K1/EMU10K2 driver
A thread appeared on the LKML. This patch implements the fix.
Question:
in sysfs, /sys/bus/*/drivers lists the driver names, with their exported .name (eg. '.name = 'EMU10K1_Audigy'' in the module code, from now on 'driver name'). In /sys/modules, the kernel modules are listed with their module name, eg. snd_emu10k1. However, it seems to me that in sysfs, there is no way in particular to tell, which module has which .name. That is, that snd_emu10k1 is EMU10K1_Audigy and vice versa.
I wonder whether it wouldn't be possible to add a symlink to the particular module from the driver, and/or from the module to the driver, so the list of devices handled by the module and the module name would be accessible. This way, I would know which driver name corresponds to which module name and vice versa.
Answer:
For PCI drivers, just add the line:
.owner = THIS_MODULE,
to their struct pci_driver definition and you will get the symlink
created for you.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
AC97 Codec
Fix the internal speaker problem (e.g. Targa Traveller 826)
with ALC658D codec. The info is taken from Cyberlink/realtek-modified code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
RME HDSP driver
When using the kernel firmware loader, initialize the card shortname
before registering the card with ALSA to prevent it from using a
default card ID.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
PCI drivers,AD1889 driver
move the AD1889 driver to the kernel tree
Acked-by: Thibaut Varene <varenet@parisc-linux.org>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
CA0106 driver
Playback volume controls were appearing in both the playback and capture
displays of alsamixer. Now those playback controls only appear in the
playback display.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
This patch introduces a memory-leak tracking version of kzalloc for ALSA.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Jaroslav Kysela <perex@suse.cz>
Signed-off-by: Jiri Slaby <xslaby@fi.muni.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix remaining bits of u32 vs. pm_message confusion. Should not break
anything.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HDA Intel driver
Fix and clean up for the support of ULI M5461
- set CORB/RIRB sizes explicitly
- add workarounds for ULI on ia32
- max number of streams depends on the chip type now
- increase the size of BDL
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
The insertion of the rate 9600 make a shift in detection of supported
rate, put this rate at the end of the list.
Signed-off-by: Nicolas Graziano <nicolas.graziano@wanadoo.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel8x0 driver,AC97 Codec
The HP nx6110 laptop needs to have Headphone Jack Sense enabled so
that the internal speakers will be turned off when headphones are
plugged in.
Also ac97_quirk=hp_only is needed to make a single Master volume in
the mixer instead of separate volumes for internal speakers and
headphones, which just confuses the user.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digigram VX core,CS4231 driver,ATIIXP driver,VIA82xx driver
VIA82xx-modem driver,au88x0 driver,CS46xx driver,Trident driver
This patch disables SNDRV_PCM_INFO_RESUME flag for drivers which does not
support the full resume.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
AC97 Codec
The patch fixes the bus_id conflict error when registering two codecs
of the same type (ALSA bug#1334).
Signed-off-by: Bjorge Dijkstra <bjorge@gmx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NM256 driver
- Fixed the PCM resume - restoring the rate setting
- Fixed the handling of buggy irqs
- Dynamically acquire/release irq handler to make the driver more robust
to unknown irq storms (as OSS driver does).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Intel driver
- removed SNDRV_PCM_INFO_RESUME (the driver cannot do PCM resume at the time)
- fixed chip->pcm_devs initialization
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
AC97 Codec
Make the patch_wolfson_wm97??_specific() functions static again.
This patch was accidentally reverted in rev. 1.92.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
VIA82xx driver
Added the DXS entry for MSI K8MM-V.
Also fixed a typo in last patch for Acer Aspire 1524 WLMi.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Memalloc module,PCM Midlevel,Timer Midlevel,GUS Library,AC97 Codec
ALI5451 driver,RME9652 driver
Make some functions/variables that are used in only one file static.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
YMFPCI driver
Implements mixer controls for the volume of each playback substream of
the main PCM device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
AC97 Codec
This patch fixes a problem whereby the WM9713 has modem functionality
incorrectly detected after an AC97 cold reset.
Changes:-
o Cleared AC97_SCAP_MODEM in wm9713 scaps
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digigram VX core,ENS1370/1+ driver,CA0106 driver,EMU10K1/EMU10K2 driver
RME HDSP driver,RME9652 driver
For consistency, use the PCM interface instead of MIXER for IEC958
default/mask/stream mixer controls.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
CMI8330 driver,ENS1370/1+ driver,FM801 driver,VIA82xx driver,AC97 Codec
ALI5451 driver,CS46xx driver,EMU10K1/EMU10K2 driver,HDA Codec driver
ICE1712 driver,ICE1724 driver
Where appropriate, use the SNDRV_CTL_NAME_IEC958 instead of a literal
string.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
AC97 Codec,PCI drivers
I've made the review changes and as requested I've pasted the RFC by
Nicolas below:-
'I would like to know what people think of the following patch. It
allows for a codec on an AC97 bus to be shared with other drivers which
are completely unrelated to audio. It registers a new bus type, and
whenever a codec instance is created then a device for it is also
registered with the driver model using that bus type. This allows, for
example, to use the extra features of the UCB1400 like the touchscreen
interface and the additional GPIOs and ADCs available on that chip for
battery monitoring. I have a working UCB1400 touchscreen driver here
that simply registers with the driver model happily working alongside
with audio features using this.'
Changes over RFC:-
o Now matches codec name within codec group.
o Added ac97_dev_release() to stop kernel complaining about no release
method for device.
o Added 'config SND_AC97_BUS' to sound/pci/Kconfig and moved 'config
SND_AC97_CODEC' out with the PCI=n statement.
o module is now called snd-ac97-bus
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,CS46xx driver,EMU10K1/EMU10K2 driver,AD1848 driver
SB16/AWE driver,CMIPCI driver,ENS1370/1+ driver,RME32 driver
RME96 driver,ICE1712 driver,ICE1724 driver,KORG1212 driver
RME HDSP driver,RME9652 driver
This patch changes .iface to SNDRV_CTL_ELEM_IFACE_MIXER whre _PCM or
_HWDEP was used in controls that are not associated with a specific PCM
(sub)stream or hwdep device, and changes some controls that got
inconsitent .iface values due to copy+paste errors. Furthermore, it
makes sure that all control that do use _PCM or _HWDEP use the correct
number in the .device field.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
HDA Codec driver
- Fixed the reordering of surround channels.
Originally reported by Nicolas GRAZIANO <nicolas.graziano@wanadoo.fr>.
- Show the selected ssid when debug option is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
o Enhanced current WM97xx support to provide additional controls and
use the kcontrol suffix naming convention.
o Added AC97_HAS_NO_MIC, AC97_HAS_NO_TONE and AC97_HAS_NO_STD_PCM.
o Cleaned up WM97xx related comments.
o Removed some wm9713 double mono controls and replaced with stereo
controls.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
fixed kconfig dependencies on ISA_DMA_API for parts of sound/* that rely
on it.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HDA Codec driver
- Correct some index variable inversion in patch_cmedia.c
Signed-off-by: Nicolas Graziano <nicolas.graziano@wanadoo.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ENS1370/1+ driver,ES1968 driver,Intel8x0 driver,VIA82xx driver
VIA82xx-modem driver,AC97 Codec,ALI5451 driver,CS46xx driver
MIXART driver,RME HDSP driver,Trident driver,YMFPCI driver
Description: Fix-up sleeping in sound/pci. These changes fall under the
following two categories:
1) Replace schedule_timeout() with msleep() to guarantee the
task delays as expected. This also involved replacing/removing
custom sleep functions.
2) Do not assume jiffies will only increment by one if you
request a 1 jiffy sleep, i.e. use time_after/time_before in
while loops.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
EMU10K1/EMU10K2 driver
It allows the user to force the snd-emu10k1 module to think the user
has a particular sound card. Useful if their particular sound card
is not yet recognised.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
RME HDSP driver
Added 'Sample Clock Source Locking' control. If this switch is on,
the clock source can't be changed via PCM hw_params API (as sample rate).
This will fix the problem of OSS-emulation, for example.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Adds support for detecting hp insertion/removal and enable/disable of
lineouts based on unsolicited events.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Intel driver
Patch enables unsolicited responses on the HDA controller. Without
the UREN bit set, the controller will not place unsolicited responses
in a RIRB.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel8x0 driver,AC97 Codec
Fix resume of intel8x0 driver. The ac97 codec didn't restore some registers
properly, and the restore of ICH4 SPDIF and SDIN settings was missing.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,HDA Codec driver
- Added a new '6stack' model for ALC880.
- Fixed the typo in 6stack-digout model name.
- Added description for missing models in ALSA-Configuration.txt.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ATIIXP-modem driver
I didn't actually test whether the modem works, but at least the driver
loads and initializes fine. Please consider inclusion.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Adds resume support to the SigmaTel HDA patch. Please apply.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
turn many #if $undefined_string into #ifdef $undefined_string to fix some
warnings after -Wno-def was added to global CFLAGS
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Just the declaration fix wasn't enough to fix things in bt78x.c
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The dynamic pci id logic has been bothering me for a while, and now that
I started to look into how to move some of this to the driver core, I
thought it was time to clean it all up.
It ends up making the code smaller, and easier to follow, and fixes a
few bugs at the same time (dynamic ids were not being matched
everywhere, and so could be missed on some call paths for new devices,
semaphore not needed to be grabbed when adding a new id and calling the
driver core, etc.)
I also renamed the function pci_match_device() to pci_match_id() as
that's what it really does.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch creates a new kstrdup library function and changes the "local"
implementations in several places to use this function.
Most of the changes come from the sound and net subsystems. The sound part
had already been acknowledged by Takashi Iwai and the net part by David S.
Miller.
I left UML alone for now because I would need more time to read the code
carefully before making changes there.
Signed-off-by: Paulo Marques <pmarques@grupopie.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HDA Codec driver
Adds SPDIF in/out support to the SigmaTel HDA codecs. Now builds
the input mux control element names from the defcfg regs.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,HDA Codec driver,HDA generic driver,HDA Intel driver
- Fix some invalid configurations, typos in the last patch
- Make init_verbs chainable, so that different configs can share the same
init_verbs
- Reorder and clean up the source codes in patch_realtek.c
- Add the pin default configuration parser, used commonly in cmedia
and realtek patch codes.
- Add 'auto' model to ALC880 for auto-configuration from BIOS
Use this model as default, and 3-stack as fallback
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver,HDA Intel driver
Merged the work of pshou <pshou@realtek.com.tw> for the support of
more models with ALC codecs: ALC880 ASUS, Uniwill, FSC1734, generic 6-stack,
and ALC260 HP. Tests with the real hardwares are appreciated.
The codec patch is cleaned up: The preset configuration of codecs are
stored in the table and copied to the spec instance.
Added/fixed comments.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Allow sub_device=0 in board config check. This means that every device
with the given sub vendor ID will match.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Clean up and fix ALC-codec support code.
The last addition of bound volume is fixed now to handle correctly
the bound 'mute switches'. The analog loopback should work better.
The init verbs are fixed together with this change.
The numbers are replaced with macros for better readability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Feed front signals to all surround channels if no data is given
for surround channels.
It seems that CLFE works as expected (only center outputs) even if
connected from the front line - at least on my test system.
If this change causes problems on other system (e.g. only the left
channel is transferred to the center channel), please let me know...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Fixed the handling of amp cache in hda-codec driver.
The confliction of cache values with different indices should be fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,Memalloc module,RME HDSP driver,RME9652 driver
Add the write support to snd-page-alloc proc file for buffer pre-allocation.
Removed the pre-allocation codes via module options.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Timer Midlevel,ALSA sequencer,ALSA<-OSS sequencer,Digigram VX core
I2C tea6330t,GUS Library,VIA82xx driver,VIA82xx-modem driver
CA0106 driver,CS46xx driver,EMU10K1/EMU10K2 driver,YMFPCI driver
Digigram VX Pocket driver,Common EMU synth,USB generic driver,USB USX2Y
Checking a pointer for NULL before calling kfree() on it is redundant,
kfree() deals with NULL pointers just fine.
This patch removes such checks from sound/
This patch also makes another, but closely related, change.
It avoids casting pointers about to be kfree()'ed.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel8x0 driver
To avoid confusion, the structure members vendor/device were renamed
to subvendor/subdevice, because we compare them with PCI subsystem vendor
and subsystem device.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
AC97 Codec,ATIIXP driver,VIA82xx driver
To avoid confusion, the structure members vendor/device were renamed
to subvendor/subdevice, because we compare them with PCI subsystem vendor
and subsystem device.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
ALI5451 driver
This patch adds modem support for ali5451. Since it is same pci device
all is done in ali5451.c.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
CA0106 driver
Use the DMA_32BIT_MASK constant from dma-mapping.h
when calling pci_set_dma_mask() or pci_set_consistent_dma_mask()
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
AC97 Codec
Simple MC97 modem mixer with two common controls: Off-hook and CID,
and Si3056 MC specific control: Modem Speaker.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Documentation,ICE1724 driver
Add the support of Chaintech AV-710 to ice1724 driver.
The patch includes the WM-codec initialization fix by
Jaanus Kivistik <jaanus@no.spam.ee>.
Since both AV-710 and AMP Audio2000 have the same SSID, initialize
WM codecs as default for both devices. In case it breaks Audio2000,
you can pass 'model=amp2000' option to avoid WM codec initialization.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Fixed the capture on some ALC880 devices.
The node 0x07 is sometimes invalid as an ADC. Also, the intialization
of ADC nodes are fixed on some models.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,ICE1712 driver
Updated the documentation for ice1712 and ice1724 drivers.
Added the device description for shuttle SN25P missing in the last patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CA0106 driver
This fixes a bug whereby when the snd-ca0106 module first loads,
alsamixer says 'SPDIF Out [Off]' but no analog sound comes from the speakers.
This covers any bug reports that said things like
'mixer fails to remember analog output on, when the system is rebooted.'
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
Maestro3 driver
Add a hardware volume quirk list to the maestro3 driver. Details were
taken from the Windows driver. Hardware volume control is enabled only for
the systems in the list.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Suppressing the error message regarding no AFG.
This is often harmless (e.g. probing a modem codec).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CA0106 driver,HDA Codec driver
This patch makes needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,HDA Intel driver
Added the support of VIA VT8251/VT8237A HD-Audio controllers.
They are (almost) compatible with Intel ICH6/7.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,HDA Intel driver
This patch changes the Intel HD Audio device driver to include
the support of HD Audio device embedded in ATI south bridge
IXP450. Because the design of ATI chipset follows intel HD Audio
specification 1.0, the programming method is the same as that
of intel HD Audio device exception one minor change which requires
to enable snoop for DMA transport. There are 3 changes that have been
made to hda_intel.c file.
1. Added device ID for ATI HD Audio device;
2. Increase maximum CODEC supported to 4;
3. Enable snoop during the driver initialization.
Signed-off-by: Frederick Li <fli@ati.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver
Added 'test' model for testing/debugging the devices with ALC880 codec.
This model is built only when CONFIG_SND_DEBUG is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,HDA Intel driver
Added position_fix module option to HDA-intel driver for fixing up
the DMA position (possibly hardware-) bugs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Maestro3 driver
Some HP OmniBook laptops (500 and 6000 at least) require some GPIO magic
before the HW volume buttons work. This patch makes them work mostly.
Something is still missing to make them work perfectly. However I have been
unable to figure out what exactly.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Maestro3 driver
Due to a typo interrupts were never actually acked or disabled.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
The following patch adds SB0060 to emu_chip_details.
Signed-off-by: Mikael Magnusson <mikaelmagnusson@glocalnet.net>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
AC97 Codec
The code for AD1980/AD1985/AD1986 codecs forgot to enable the code to
switch the jack sharing bits on AD1888-compatible codecs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
AC97 Codec
The code for modifying the center/LFE disable bit on AD1888 codecs
accidentally toggled the mute split bit instead.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
CS4281 driver
Reset the FPDN bit of the EPPMC register if needed.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
EMU10K1/EMU10K2 driver
e.g. When HD Capture source is set to SPDIF,
setting HD Capture channel to 0 captures from CDROM digital input.
setting HD Capture channel to 1 captures from SPDIF in.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
EMU10K1/EMU10K2 driver
The capture rate does in fact vary, but it only captures anything if
the HD Capture source is set to I2S or AC97. I have not tested if the sound
is actually captured from an physical input of some type or not.
TODO: Get SPDIF capture working.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
AC97 Codec
Add the 'Mic Front Input Switch' control to the mixer for ALC850.
Enabling this input is required for using the front panel microphone
connector with ASUS A8V motherboard.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
AC97 Codec
ac97_enum mixer elements (e.g., 'Capture Source') did not work because
of wrong bitmask calculation in snd_ac97_get_enum_double() and
snd_ac97_put_enum_double().
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1072
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
HDA Codec driver
Fix and cleanup of CM9880 automatic PIN configuration.
snd_hda_codec_setup_stream() doesn't do anything when NID is 0.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
When building with gcc -W sound/pci/emu10k1/emupcm.c produces this little
warning in 2.6.12-rc2-mm3 :
sound/pci/emu10k1/emupcm.c:265: warning: 'inline' is not at beginning of
declaration
No big deal, but trivial to fix.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA generic driver,HDA Codec driver
Add initial SigmaTel codec support for 9200 and 922x. Note that
this hda patch relies on the configuration default registers to
be set correctly (normally by BIOS/firmware) in order for it to
set up pin widgets properly. There's a test switch in the patch
so it will work with the SigmaTel reference boards that are usually
plugged into a system that doesn't set the configuration default
registers. It supports 2 channel analog out and line/mic in. I
plan to add >2 channel support and spdif support shortly.
Please apply.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA Codec driver,HDA generic driver
Fix some vref defines so they are valid for the different bits in
the pin cap and pin control registers. Please apply.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
The handling of shared surround/clfe output jacks with line/mic-in
on some AC97 codecs is improved.
Instead of 'Line-In As Surround' or 'Mic As Center/LFE' switch, two
new enum controls are introduced: 'Channel Mode' and 'Surround Jack Mode'.
The formar changes the current output mode among 2, 4 and 6-channels.
The latter controls whether the jacks are shared or independent.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PCM Midlevel,CA0106 driver,EMU10K1/EMU10K2 driver
Fix by Guillaume Chazarain <guichaz@yahoo.fr>:
Some tunables in /proc have a write() function, but as their
permission does not reflect it, it can be confusing to the user.
So here is a patch that corrects the mode of those files. Note that I
have only tested the 'xrun_debug' entry.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,VIA82xx driver
Add support for full sample rate conversion capabilities of DXS
channels present in VIA VT8233/5/7 controllers:
- any sample rate in the 8000 ... 48000 Hz range is supported even if
the AC'97 codec supports only 48000 Hz output;
- different DXS channels can use different sample rates at the same
time (the controller performs required sample rate conversion and
mixing in hardware).
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
FM801 driver
The Gallant Odyssey Sound 4 card is based on the ForteMedia FM801
chip, but has a different PCI ID.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
YMFPCI driver
This patch removes some dead code found by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ICE1712 driver
Provides preliminary support for the Terratec Phase 28 card.
Not extensively tested and probably buggy, but it seems to work.
Signed-off-by: Simone Zinanni <simone@develer.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
Although we can set 44100 as the output rate, the SPDIF can do it, but the Analog output cannot.
The SPDIF has the bug, whereby the Left channel arrives one sample late, so although we don't do any resampling,
it is not good for AC3 non-audio output.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
HDA Codec driver
Patch by C.L. Tien <cltien@cmedia.com.tw>:
The patch makes cm9880 to choose multi-channel jacks automatically.
1. I found the current code has basic_init, which already includes
necessary controls for 6-stack initialization, so I don't need
another model.
2. I add a new model 'auto' to let the driver find a. if there are
option real panel/front panel, b. the jacks to be used for multichannel.
Because the jack color are based on MS's channel sequence, so the 'auto'
model will pick the same jacks for multichannel MS uses. I did this to
hope to minimize users questions. These code can also be applied to other
codecs but I don't have any to test.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel8x0-modem driver
With some intel based ac97 modems codec access semaphore is not cleared
after 0x54 AC97 register (GPIO_STATUS) reads. This may causes problems
with newly applied modem mixer (Off-hook switch) and in other cases.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
- Added CM9780 patch
- Fix the SPDIF support on CM9761/CM9780
- Allow the generic enum callback to pass any number (not power of 2)
as the value mask
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
This add identification of Audigy 1 model SB0090 and fixes
problems with ac97 codec (mic not working).
Signed-off-by: Peter Zubaj <pzad@pobox.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
Use expliciitly the old default id strings for backward compatibility.
This will make 'alsactl restore' working again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
This patch converts the emu10k1 driver to use the card capabilities
structure for some more things.
Not extensively tested but seems to work.
Signed-off-by: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
Fixed the detection of bit resolution of ac97 mixer controls.
This will fix the problem with TI ac97 codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EMU10K1/EMU10K2 driver
One can select which capture source, but one cannot yet set volumes.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
HDA Codec driver
The patch_cm9880.c can't play side/C/B channels from front panel jacks.
I fixed it by adding select pin.
Signed-off-by: ChenLi Tien <cltien@cmedia.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDA generic driver
During debugging for cm9880 multi-channel playback, I added the * after
the currently selected widget, mixer widget doesn't need this but other
3 widget types need it.
Signed-off-by: ChenLi Tien <cltien@cmedia.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Trying software suspend on my workstation makes it crash on resume. The
problem is that via82xx marks the chip_init function as _devinit, but calls
it on resume as well.
Cc: <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a typo in the Intel AC'97 audio driver intel8x0.c for
Intel ESB2.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Cc: <tiwai@suse.de>
Cc: <perex@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the Intel ESB2 HD Audio DID to the hda_intel.c audio driver.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I thought I'm done with fixing u32 vs. pm_message_t ... unfortunately that
turned out not to be the case as Russel King pointed out. This fixes last few
bits in alsa.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the Intel ESB2 DID's to the intel8x0.c file for AC'97 audio
support.
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
