This patch fixes the nic initialization. If the nic was in low power
mode, it brings it back to normal power. Also, it utilizes a new
hardware reset during the init.
I am resending based on feedback, I corrected the register size mapping
and delay after posted write.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2_reset function only called from sky2_probe.
Maybe the compiler was smart enough to figure this out already.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ALIGN() macro in kernel.h does the same math that the
sky2 driver was using for padding.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add an fake NAPI schedule once a second. This is an attempt to work around
for broken configurations with edge-triggered interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a workaround for the case edge-triggered irq's. Several users
seem to have broken configurations sharing edge-triggered irq's. To avoid
losing IRQ's, reshedule if more work arrives.
The changes to netdevice.h are to extract the part that puts device
back in list into separate inline.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update skb with the real packet size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
This patch fixes PIO mode on the softmac bcm43xx
driver. (A dscape patch will follow).
It mainly fixes endianess issues.
This patch is tested on PowerPC32 and i386.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original code was doing arithmetics on a little-endian value.
Reported by Stelios Koroneos <stelios@stelioscellar.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes several bugs in the gianfar driver, including a major one
where spinlocks were horribly broken:
* Split gianfar locks into two types: TX and RX
* Made it so gfar_start() now clears RHALT
* Fixed a bug where calling gfar_start_xmit() with interrupts off would
corrupt the interrupt state
* Fixed a bug where a frame could potentially arrive, and never be handled
(if no more frames arrived
* Fixed a bug where the rx_work_limit would never be observed by the rx
completion code
* Fixed a bug where the interrupt handlers were not actually protected by
their spinlocks
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct the base address of the Realtek RTL8019AS chip on the Toshiba RBTX4938
board -- this should make the driver work at least when CONFIG_PCI is enabled.
Signed-off-by: Yuri Shpilevsky <yshpilevsky@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In a short discussion with Benjamin Herrenschmidt he mentioned
that Marvell PHYs are powered down the same way as the other
ones we currently handle. Thus actually do that, hopefully
saving some power during suspend.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The room for the names in bcm43xx_priv_wx_args[] are IFNAMSIZ long and
IFNAMSIZ is defined as 16, so the names in bcm43xx_priv_wx_args should
be 15 characters (16 including the trailing \0). This patch fixes that
for the "set_shortpreambl", "get_shortpreambl", "set_swencryption", and
"get_swencryption" private calls. Patch is against 2.6.17-rc1.
Signed-off-by: Erik Mouw <erik@harddisk-recovery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This cleans up the bcm43xx sysfs code and makes it compliant
with the unwritten sysfs rules (at least I hope so).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a memory leak spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "depends on" to make all bcm43xx driver options be listed
at the same level.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix printk format warnings:
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:456: warning: format ‘%u’ expects type ‘unsigned int’, but argument 3 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:460: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:476: warning: format ‘%u’ expects type ‘unsigned int’, but argument 3 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:480: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘size_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:200: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:311: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
drivers/net/wireless/bcm43xx/bcm43xx_dma.c:733: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘dma_addr_t’
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Symbol firmware F3.91-71 has an additional word in the commsquality RID.
Extend the receiving buffer by one word to accomodate it.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2.6.17-rc1 changed the title for the entry CONFIG_NET_RADIO. I
personally disagree with this change and want it reverted. Patch for
2.6.17-rc1.
Rationale : WIRELESS_EXT is an invisible option. Therefore,
the only way for a user to enable it is via NET_RADIO. Some users need
to do that for out-of-tree drivers. Therefore it should be mentionned
in the title of the option.
Rationale2 : the option just below is called "Wireless
Extension API over RtNetlink". Some users may confuse this option for
the main "Wireless Extension" option. Therefore reverting this change
help disambiguate the relation between those two options.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send scan completion events to user space when a scan completes.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Airo firmware versions >= 5.30.17 send re-association events to the
driver that are currently unrecognized, causing spurious disassociation
events to be sent to user space. Loss of sync due to scan requests also
results in disassociation events sent to user space. This patch traps
those two events; suppressing sync-loss on scan, and sending the correct
association event on re-association notifications.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From: Linus Walleij <triad@df.lth.se>
This patch enables support for ALi ISA bridges when we run the smcinit
code. It is needed to properly configure some Toshiba laptops.
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the STIR421x case, when the firmware upload fails, we need to
unregister_netdev. Otherwise we hit a BUG on free_netdev(), if sysfs
is enabled.
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[PATCH] Use pci_set_consistent_dma_mask in ixgb driver
[PATCH] sky2: bad memory reference on dual port cards
[PATCH] mv643xx_eth: Fix tx_timeout to only conditionally wake tx queue
[PATCH] mv643xx_eth: Always free completed tx descs on tx interrupt
[PATCH] net drivers: fix section attributes for gcc
[PATCH] remove drivers/net/hydra.h
[PATCH] drivers/net/via-rhine.c: make a function static
[netdrvr b44] trim trailing whitespace
[PATCH] b44: increase version to 1.00
[PATCH] b44: disable default tx pause
[PATCH] via-rhine: execute bounce buffers code on Rhine-I only
[PATCH] network: axnet_cs.c: add missing 'PRIV' in ei_rx_overrun
[PATCH] dlink pci cards using wrong driver
The ixgb driver is using pci_alloc_consistent, thus is should also use
pci_set_consistent_dma_mask. This allows the driver to work on SGI
systems.
In case of an error during probing it should also disable the device again.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sky2 driver will oops referencing bad memory if used on
a dual port card. The problem is accessing past end of
MIB counter space.
Applies for both 2.6.17 and 2.6.16 (with fuzz)
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After resetting the hardware on a tx_timeout, call netif_wake_queue()
only if we have free tx descriptors.
Also, attempt to recover if mv643xx_eth_start_xmit() is called when
there are fewer free tx descriptors than expected.
The BUG_ON() call we are replacing was hit on a tx_timeout that
called netif_wake_queue(), indirectly via netif_device_attach(),
even though we did not have enough free tx descriptors.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the tx interrupt handler to free completed tx descriptors even
when NAPI is enabled. Otherwise, the tx queue would fill up resulting
in poor performance and "NETDEV WATCHDOG: <iface>: transmit timed out"
messages.
Signed-off-by: Brent Cook <bcook@bpointsys.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If CONFIG_HOTPLUG=n, gcc doesn't like some __initdata to be const (rodata)
and other __initdata not const, so make the non-const __initdata const.
gcc errors:
drivers/net/bnx2.c:66: error: version causes a section type conflict
drivers/net/starfire.c:338: error: version causes a section type conflict
drivers/net/typhoon.c:137: error: version causes a section type conflict
drivers/net/natsemi.c:241: error: version causes a section type conflict
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove drivers/net/hydra.h which is both unused and covered by a 4 clause
BSD licence (not by the UCB).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-By: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Disable default tx pause frame support.
The b44 controller has a bug that generates excessive tx pause
frames.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the problem of some Dlink cards picking the wrong
driver. It looks like these cards use Yukon 1 chipset, not Yukon 2.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The in-kernel Sangoma drivers are both not compiling and marked as BROKEN
since at least kernel 2.6.0.
Sangoma offers out-of-tree drivers, and David Mandelstam told me Sangoma
does no longer maintain the in-kernel drivers and prefers to provide them
as a separate installation package.
This patch therefore removes these drivers.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kconfig: fix typo in change count initialization
kconfig: recenter menuconfig
kconfig: revert conf behaviour change
kconfig: fix default value for choice input
kbuild: fix NULL dereference in scripts/mod/modpost.c
kbuild: fix mode of checkstack.pl and other files.
kbuild: rebuild initramfs if content of initramfs changes
kbuild: properly pass options to hostcc when doing make O=..
kbuild: modules_install for external modules must not remove existing modules
kbuild: fix make dir/
ver_linux: don't print reiser4progs version if none found
kbuild: mips: fix sed regexp to generate asm-offset.h
kbuild: fix building single targets with make O=.. single-target
kbuild: use relative path to -I
kbuild: fix unneeded rebuilds in drivers/net/chelsio after moving source tree
kbuild: fix unneeded rebuilds in drivers/media/video after moving source tree
kbuild: fix garbled text in modules.txt
Speed up SRAM read and write functions if possible by using MMIO
instead of config. cycles. With this change, the post reset signature
done at the end of D3 power change must now be moved before the D3
power change.
IBM reported a problem on powerpc blades during ethtool self test that
was caused by the memory test taking excessively long. Config. cycles
are very slow on powerpc and the memory test can take more than 10
seconds to complete using config. cycles.
David Miller informed me that an earlier version of the patch caused
problems on sparc64 systems with built-in tg3 chips. This version
fixes the problem by excluding all SUN built-in tg3 chips from doing
MMIO SRAM access.
TG3_FLAG_EEPROM_WRITE_PROT is also set unconditionally when
TG3_FLG2_SUN_570X is set. This should be sane as all SUN chips are
built-in and do not require Vaux switching.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill the TG3_FLAG_NO_{TX|RX}_PSEUDO_CSUM flags because they are not
very useful. This will free up some bits for new flags.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables support for the Sigmatel's STIR421x IrDA chip.
Once patched with Sigmatel's firmware, this chip "almost" follows the
USB-IrDA spec. Thus this patch is against irda-usb.[ch].
The code has been tested by Nick Fedchik on an STIR4210 chipset based
dongle.
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
