Kernel 2.6.18 broke the MotU Fastlane, which uses duplicate endpoint
numbers in a manner that is not only illegal but also confuses the
kernel's endpoint descriptor caching mechanism. To work around this, we
have to add a separate usb_set_interface() call to guide the USB core to
the correct descriptors.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: David Fries <david@fries.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To enable periods shorter than 1 ms, we have to make sure that short
periods are only available for alternate settings that have a small
enough data packet interval. Furthermore, the code that aligns URBs to
USB frames is now superfluous.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The data packet interval needs to be available in the audioformat
structure, together with the other audio format parameters, so that it
can be used to influence ALSA hardware parameters.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This removes the check_hw_params_convention() function because
1) it is not necessary, as the hw_rule_* functions also work correctly
(i.e., as no-ops) when the device supports all combinations of the
audio format parameters; and
2) it would become too complex when adding a fourth altsetting-dependent
hardware parameter, as this would require another three loops to
check dependecies with rate/channels/format.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When listing the device's sample formats in the stream? proc file, the
sample format number itself is rather obscure, so we better show the
format width, too.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When checking for the maximum queue length, we have to take into account
that MAX_QUEUE is measured in milliseconds (i.e., frames) while the unit
of urb_packs is whatever data packet interval the device uses (possibly
less than one frame when using high speed devices).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When storing the channel numbers used by a format, and if the device
happens to support 32 channels, the code would try to store 1<<32 in
a 32-bit value.
Since no valid format can have zero channels, we can use 1<<(channels-1)
instead of 1<<channels so that all the channel numbers that we test for
fit into 32 bits.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the MIN_PACKS_URB symbol because other limits can force the
number of packets down to one, regardless of the value of this symbol,
and nobody has ever changed it anyway.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The CM6207 incorrectly advertises its 96 kHz playback setting as 48 kHz
in its USB device descriptor. This patch extends an existing workaround
in usbaudio.c to also cover the CM6207.
This resolves issue 0004249 in the ALSA bug tracker.
Signed-off-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The detection of non-continuous rates (given via rate tables) isn't
processed properly (e.g. for type II).
This patch fixes and simplifies the detection code.
Tested-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For audio devices that do not have proper audio descriptors (e.g.,
Edirol UA-20), we use hardcoded parameters from our quirks list.
However, we must still read the maximum packet size from the standard
endpoint descriptor; otherwise, we might use packets that are too big
and therefore rejected by the USB core.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rather use printf format instead of hardcoding prefix like 0x.
A next step would be to predefine certain formats.
Signed-off-by: Andreas Bergmeier <lcid-fire@gmx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Distribute the packets evenly among the URBs, instead of making all URBs
except the last one to have the maximum size. This makes the timing of
pointer updates more regular and removes some special cases from the
code.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Once our URBs contain enough packets, queueing more URBs does not give
us any additional underrun protection (as we use double-buffering) but
just increases latency unnecessarily. Therefore, we try to limit the
queue length to some reasonable value.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When sending a silence URB (before playback has started, or when it is
paused), use the number of frames that would be normally sent instead of
a single frame so that the rate at which completion interrupts arrive is
consistent.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the USB functions usb_get_intfdata and usb_set_intfdata instead of
dev_get_drvdata and dev_set_drvdata, respectively.
The semantic patch that makes this change for the usb_get_intfdata case is
as follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@header@
@@
#include <linux/usb.h>
@same depends on header@
position p;
@@
usb_get_intfdata@p(...) { ... }
@depends on header@
position _p!=same.p;
identifier _f;
struct usb_interface*intf;
@@
_f@_p(...) { <+...
- dev_get_drvdata(&intf->dev)
+ usb_get_intfdata(intf)
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The MIDI interfaces have to be detected dynamically for Edirol devices
ua-700, ua-25 and ua4-fx. This patch reverses the wrong changes made by
my other patch in uaxx-quirk.
Signed-off-by: Pedro Lopez-Cabanillas <pedro.lopez.cabanillas@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Renamed the old quirk function for ua-700/ua-25 to become more
generic, moving the MIDI interfaces to the quirk data header.
Added a new quirk for the Edirol UA-4FX.
Signed-off-by: Pedro Lopez-Cabanillas <pedro.lopez.cabanillas@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add support for the E-Mu "Tracker Pre" USB sound card, following
the example of the (very similar) E-Mu 0202 and E-Mu 0404 USB.
As with the 0202 and 0404 USB, functionality is very limited:
just a couple of sample rates, no volume/mute control, etc.
Signed-off-by: Eran Tromer <eran@tromer.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the ignore_ctl_error parameter to enable/disable the control-error
handling for mixer interfaces. It was a hard-coded ifdef, and now you
can change it more easily.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Kill snd_assert() in other places, either removed or replaced with
if () with snd_BUG_ON().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Since USB_EHCI_SPLIT_ISO is now unconditionally enabled the
#ifndef CONFIG_USB_EHCI_SPLIT_ISO became wrong.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the race at reconnection of the device.
The disconnected usb_chip[] must be cleared before the next probe
call properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Putting space between ! and variable is a strange coding style, fix
that, also make it fit into 80 columns where that is easy.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
usb audio contains useful debugging code, protected by #if
0. Unfortunately, it will not compile because variable names changed;
fix it.
Dallas workaround is formatted in a way where it is not quite obvious
what is normal code and what is quirk. Reformat it to make it obvious.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dallas USB speakers are buggy in more than one way. One of configs
they offer does not work at all.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a workaround for the feedback pipe of E-Mu 0202/0404 USB devices
that reports the number of samples per packet instead of the number of
samples per microframe.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
sound/usb/usbaudio.c: In function 'usb_audio_suspend':
sound/usb/usbaudio.c:3674: error: implicit declaration of function 'snd_pcm_sus\pend_all'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch implements suspend/resume support for USB audio devices.
It works with the microphone in my camera.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
usb_set_interface() can fail, even for altsetting 0
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Allow low speed MIDI devices because newer devices from ESI do not
support full speed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add a snd_pcm_rate_to_rate_bit() function to factor out common code used
by several drivers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fixed AC3 interface in device_setup=0x00 mode thanks to Hakan
Lennestal and updated documentation
Signed-off-by: Thibault Le Meur <Thibault.LeMeur@supelec.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Audiophile-usb fix (corrects little-endianness in 16bit
modes, resets interfaces at device initialization, and updates the
documentation).
Signed-off-by: Thibault Le Meur <Thibault.LeMeur@supelec.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The last patch didn't really work (false report).
Although the hardware supports 125us minimum period, the current
usb-audio driver code assumes the 1ms period in many places.
Rollback the change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The minimal period size is 125us for high-speed mode while
1ms for full-speed mode.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Recent changes in usbcore removed the bandwidth field from struct urb.
Remove the occurence in usbaudio.c
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added support for the Edirol UA-101 (only in high-speed mode) by taking
the quirks for the UA-1000 and change them accordingly. Changes were
made in 'usbaudio.c', 'usbaudio.h', and 'usbquirks.h'
MIDI and recording seem to work perfectly (with JACK), but playback
gives some few glitches. I think that's the mentioned
synchronizing-problem in the UA-1000 quirk ('FIXME: playback must be
synchronized to capture'), so I didn't change that.
ToDo: Adding Mixer-Support for the built-in
control-panel/patch-bay/router.
Signed-off-by: Bjoern Fay <mail@bfay.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The patch fixes the memory corruption by the support of unconventional
sample rates. Also, it avoids the too restrictive constraints if
any of usb descriptions contain continuous rates.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This is a patch for ALSA Bug #2724. Some webcams provide bogus
settings with no valid rates. With this patch those are skipped.
Signed-off-by: Gregor Jasny <gjasny@web.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Went rummaging through usbaudio.c and found some castings that
aren't needed as far as I can see. Part of the KernelJanitors
TODO list.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add pause capabilities for both USB playback and capture streams.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
