sizeof(dp) is just the size of the pointer. Change it to the size of the
referenced structure.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Patchwork: http://patchwork.linux-mips.org/patch/789/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The handle_edge_irq() flowhandler disables edge int sources which occur
too fast (i.e. another edge comes in before the irq handler function
had a chance to finish). Currently, the mask_ack() callback does not
ack the edges in hardware, leading to an endless loop in the flowhandler
where it tries to shut up the irq source.
When I rewrote the alchemy IRQ code I wrongly assumed the mask_ack()
callback was only used by the level flowhandler, hence it omitted the
(at the time pointless) edge acks. Turned out I was wrong; so here
is a complete mask_ack implementation for Alchemy IC, which fixes
the above mentioned problem.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are 16 individual channels (NUM_DBDMA_CHANS) to save/restore plus the
global ddma block config (the +1). The last register in a channel can be
skipped since it's read-only (at offset 0x18).
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(Thanks to Al Viro for reminding me of this, via Ingo)
CPU_MASK_ALL is the (deprecated) "all bits set" cpumask, defined as so:
#define CPU_MASK_ALL (cpumask_t) { { ... } }
Taking the address of such a temporary is questionable at best,
unfortunately 321a8e9d (cpumask: add CPU_MASK_ALL_PTR macro) added
CPU_MASK_ALL_PTR:
#define CPU_MASK_ALL_PTR (&CPU_MASK_ALL)
Which formalizes this practice. One day gcc could bite us over this
usage (though we seem to have gotten away with it so far).
So replace everywhere which used &CPU_MASK_ALL or CPU_MASK_ALL_PTR
with the modern "cpu_all_mask" (a real struct cpumask *), and remove
CPU_MASK_ALL_PTR altogether.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Mike Travis <travis@sgi.com>
loops_per_jiffy depends on coreclk speed; preset it instead of
letting the kernel waste precious microseconds trying to approximate it.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Eliminate the 'allow_au1k_wait' variable. MIPS kernel installs the
Alchemy-specific wait code before timer initialization; if the C0
timer must be used for timekeeping the wait function is set to NULL
which means no wait implementation is available.
As a sideeffect, the 'wait instruction available' output in
/proc/cpuinfo now correctly indicates whether 'wait' is usable.
Run-tested on DB1200.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the following warning at boot time:
WARNING: at drivers/gpio/gpiolib.c:83 0x8021d5e0()
autorequest GPIO-207
Modules linked in:
Call Trace:[<8011e0ec>] 0x8011e0ec
[<80110a28>] 0x80110a28
[<80110a28>] 0x80110a28
[..snip..]
The current code does not request the GPIO and attempts
to set its direction, which is a violation of the GPIO API.
This patch also unhardcode the GPIO we request and use
the one we defined in the button driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a few open-coded GPIO register accesses with gpio calls.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a few GPIO register accesses in the board init code with calls to
the gpio api.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace a few GPIO register accesses in the board init code with calls
to the gpio api.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current in-kernel Alchemy GPIO support is far too inflexible for
all my use cases. To address this, the following changes are made:
* create generic functions which deal with manipulating the on-chip
GPIO1/2 blocks. Such functions are universally useful.
* Macros for GPIO2 shared interrupt management and block control.
* support for both built-in CONFIG_GPIOLIB and fast, inlined GPIO macros.
If CONFIG_GPIOLIB is not enabled, provide linux gpio framework
compatibility by directly inlining the GPIO1/2 functions. GPIO access
is limited to on-chip ones and they can be accessed as documented in
the datasheets (GPIO0-31 and 200-215).
If CONFIG_GPIOLIB is selected, two (2) gpio_chip-s, one for GPIO1 and
one for GPIO2, are registered. GPIOs can still be accessed by using
the numberspace established in the databooks.
However this is not yet flexible enough for my uses: My Alchemy
systems have a documented "external" gpio interface (fixed, different
numberspace) and can support a variety of baseboards, some of which
are equipped with I2C gpio expanders. I want to be able to provide
the default 16 GPIOs of the CPU board numbered as 0..15 and also
support gpio expanders, if present, starting as gpio16.
To achieve this, a new Kconfig symbol for Alchemy is introduced,
CONFIG_ALCHEMY_GPIO_INDIRECT, which boards can enable to signal
that they don't want the Alchemy numberspace exposed to the outside
world, but instead want to provide their own. Boards are now respon-
sible for providing the linux gpio interface glue code (either in a
custom gpio.h header (in board include directory) or with gpio_chips).
To make the board-specific inlined gpio functions work, the MIPS
Makefile must be changed so that the mach-au1x00/gpio.h header is
included _after_ the board headers, by moving the inclusion of
the mach-au1x00/ to the end of the header list.
See arch/mips/include/asm/mach-au1x00/gpio.h for more info.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add platform data for the smc91x on the PB1200/DB1200, and remove the
now unused AU1X00 entry in smc91x.h.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
This patch converts the GPIO board code to use gpiolib.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With a postfix decrement t reaches -1 rather than 0, so the fall-back will
not occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: mano@roarinelk.homelinux.net
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In Linus' current -git the cpumask member is now a pointer.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace the current sysctl-based suspend interface with a new sysfs-
based one which also uses the Linux-2.6 suspend model.
To configure wakeup sources, a subtree for the demoboards is created
under /sys/power/db1x:
sys/
`-- power
`-- db1x
|-- gpio0
|-- gpio1
|-- gpio2
|-- gpio3
|-- gpio4
|-- gpio5
|-- gpio6
|-- gpio7
|-- timer
|-- timer_timeout
|-- wakemsk
`-- wakesrc
The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2
bits of the SYS_WAKEMSK (wakeup source enable) register. Writing '1'
enables a wakesource, 0 disables it.
The 'timer_timeout' node holds the timeout in seconds after which the
TOYMATCH2 event should wake the system.
The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex),
the 'wakemsk' node can be used to get/set the wakeup mask directly.
For example, to have the timer wake the system after 10 seconds of sleep,
the following must be done in userspace:
echo 10 > /sys/power/db1x/timer_timeout
echo 1 > /sys/power/db1x/timer
echo mem > /sys/power/sleep
This patch also removes the homebrew CPU frequency switching code. I don't
understand how it could have ever worked reliably; it does not communicate
the clock changes to peripheral devices other than uarts.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/alchemy/devboards/pm.c
Implement suspend/resume for DBDMA controller and its channels.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Au1550/Au1200 have a different memory controller which requires additi-
onal code to properly put memory to sleep (code taken from AMD/RMI's
Linux-2.6.11 source package).
Also fix up the remaining pm-related paths to compile on Au1200/Au1550
platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that nothing in time.c depends on calc_clock, it can
be moved to clocks.c where it belongs.
While at it, give it a better non-generic name and call it
as soon as possible in plat_mem_init.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the 32 kHz counter1 (RTC) as clocksource / clockevent
device. As a nice side effect, this also enables use of the 'wait'
instruction for runtime idle power savings.
If the counters aren't enabled/working properly, fall back on the
cp0 counter clock code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the cpu_table:
- move detection of whether c0_config[OD] is read-only and should be set
to fix various chip errata to au1000 headers.
- move detection of write-only sys_cpupll to au1000 headers.
- remove the BCLK switching code: Activation of this features should be
left to the boards using the chips since it also affects external devices
tied to BCLK, and only the board designers know whether it is safe to
enable.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/cputable.c
There are no in-tree users, so remove them.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch attempts to modernize core Alchemy interrupt handling code.
- add irq_chips for irq controllers instead of irq type,
- add a set_type() hook to change irq trigger type during runtime,
- add a set_wake() hook to control GPIO0..7 based wakeup,
- use linux' IRQF_TRIGGER_ constants instead of homebrew ones,
- enable GENERIC_HARDIRQS_NO__DO_IRQ.
- simplify plat_irq_dispatch
- merge au1xxx_irqmap into irq.c file, the only place where its
contents are referenced.
- board_init_irq() is now mandatory for every board; use it to register
the remaining (gpio-based) interrupt sources; update all boards
accordingly.
Run-tested on Db1200 and other Au1200 based platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c
Not every alchemy-based board might want these options forced on it,
and most of this stuff seems to be intended for devboard code anyway.
Remove commandline mangling code out of common chip code and instead
add relevant sections to all in-tree boards to not change existing
behaviour.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This should ease sharing of common devboard code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since memsize is unsigned, it would seem better to use strict_strtoul that
strict_strtol.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@s2@
long e;
position p;
@@
strict_strtol@p(...,&e)
@@
position p != s2.p;
type T;
T e;
@@
- strict_strtol@p
+ strict_strtoul
(...,&e)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add au1xmmc platform data for PB1200/DB1200 boards and wire up the 2 SD
controllers for them.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
