Applied fix by Andew Morton:
http://lkml.org/lkml/2007/4/8/88 - Fix `make headers_check'.
AMD and Intel x86 CPU manuals state that it is the responsibility of
system software to initialize and maintain MTRR consistency across
all processors in Multi-Processing Environments.
Quote from page 188 of the AMD64 System Programming manual (Volume 2):
7.6.5 MTRRs in Multi-Processing Environments
"In multi-processing environments, the MTRRs located in all processors must
characterize memory in the same way. Generally, this means that identical
values are written to the MTRRs used by the processors." (short omission here)
"Failure to do so may result in coherency violations or loss of atomicity.
Processor implementations do not check the MTRR settings in other processors
to ensure consistency. It is the responsibility of system software to
initialize and maintain MTRR consistency across all processors."
Current Linux MTRR code already implements the above in the case that the
BIOS does not properly initialize MTRRs on the secondary processors,
but the case where the fixed-range MTRRs of the boot processor are changed
after Linux started to boot, before the initialsation of a secondary
processor, is not handled yet.
In this case, secondary processors are currently initialized by Linux
with MTRRs which the boot processor had very early, when mtrr_bp_init()
did run, but not with the MTRRs which the boot processor uses at the
time when that secondary processors is actually booted,
causing differing MTRR contents on the secondary processors.
Such situation happens on Acer Ferrari 1000 and 5000 notebooks where the
BIOS enables and sets AMD-specific IORR bits in the fixed-range MTRRs
of the boot processor when it transitions the system into ACPI mode.
The SMI handler of the BIOS does this in SMM, entered while Linux ACPI
code runs acpi_enable().
Other occasions where the SMI handler of the BIOS may change bits in
the MTRRs could occur as well. To initialize newly booted secodary
processors with the fixed-range MTRRs which the boot processor uses
at that time, this patch saves the fixed-range MTRRs of the boot
processor before new secondary processors are started. When the
secondary processors run their Linux initialisation code, their
fixed-range MTRRs will be updated with the saved fixed-range MTRRs.
If CONFIG_MTRR is not set, we define mtrr_save_state
as an empty statement because there is nothing to do.
Possible TODOs:
*) CPU-hotplugging outside of SMP suspend/resume is not yet tested
with this patch.
*) If, even in this case, an AP never runs i386/do_boot_cpu or x86_64/cpu_up,
then the calls to mtrr_save_state() could be replaced by calls to
mtrr_save_fixed_ranges(NULL) and mtrr_save_state() would not be
needed.
That would need either verification of the CPU-hotplug code or
at least a test on a >2 CPU machine.
*) The MTRRs of other running processors are not yet checked at this
time but it might be interesting to syncronize the MTTRs of all
processors before booting. That would be an incremental patch,
but of rather low priority since there is no machine known so
far which would require this.
AK: moved prototypes on x86-64 around to fix warnings
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
In this current implementation which is used in other patches,
mtrr_save_fixed_ranges() accepts a dummy void pointer because
in the current implementation of one of these patches, this
function may be called from smp_call_function_single() which
requires that this function takes a void pointer argument.
This function calls get_fixed_ranges(), passing mtrr_state.fixed_ranges
which is the element of the static struct which stores our current
backup of the fixed-range MTRR values which all CPUs shall be
using.
Because mtrr_save_fixed_ranges calls get_fixed_ranges after
kernel initialisation time, __init needs to be removed from
the declaration of get_fixed_ranges().
If CONFIG_MTRR is not set, we define mtrr_save_fixed_ranges
as an empty statement because there is nothing to do.
AK: Moved prototypes for x86-64 around to fix warnings
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
No, just no. You do not use goto to skip a code block. You do not
return an obvious variable from a singly-inlined function and give
the function a return value. You don't put unexplained comments
about kmalloc in code which doesn't do dynamic allocation. And
you don't leave stray warnings around for no good reason.
Also, when possible, it is better to use block scoped variables
because gcc can sometime generate better code.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Fixes two problems with the GDT when compiling for uniprocessor:
- There's no percpu segment, so trying to load its selector into %fs fails.
Use a null selector instead.
- The real gdt needs to be loaded at some point. Do it in cpu_init().
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Currently x86 (similar to x84-64) has a special per-cpu structure
called "i386_pda" which can be easily and efficiently referenced via
the %fs register. An ELF section is more flexible than a structure,
allowing any piece of code to use this area. Indeed, such a section
already exists: the per-cpu area.
So this patch:
(1) Removes the PDA and uses per-cpu variables for each current member.
(2) Replaces the __KERNEL_PDA segment with __KERNEL_PERCPU.
(3) Creates a per-cpu mirror of __per_cpu_offset called this_cpu_off, which
can be used to calculate addresses for this CPU's variables.
(4) Simplifies startup, because %fs doesn't need to be loaded with a
special segment at early boot; it can be deferred until the first
percpu area is allocated (or never for UP).
The result is less code and one less x86-specific concept.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Xen wants a dedicated page for the GDT. I believe VMI likes it too.
lguest, KVM and native don't care.
Simple transformation to page-aligned "struct gdt_page".
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com>
As a bug workaround bank 0 on K7s is normally disabled, but no need
to do that on other AMD CPUs.
Cc: davej@redhat.com
Signed-off-by: Andi Kleen <ak@suse.de>
It doesn't put the CPU into deeper sleep states, so it's better to use the standard
idle loop to save power. But allow to reenable it anyways for benchmarking.
I also removed the obsolete idle=halt on i386
Cc: andreas.herrmann@amd.com
Signed-off-by: Andi Kleen <ak@suse.de>
identify_cpu() is used to identify both the boot CPU and secondary
CPUs, but it performs some actions which only apply to the boot CPU.
Those functions are therefore really __init functions, but because
they're called by identify_cpu(), they must be marked __cpuinit.
This patch splits identify_cpu() into identify_boot_cpu() and
identify_secondary_cpu(), and calls the appropriate init functions
from each. Also, identify_boot_cpu() and all the functions it
dominates are marked __init.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Most of asm-i386/bugs.h is code which should be in a C file, so put it there.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Now we have an explicit per-cpu GDT variable, we don't need to keep the
descriptors around to use them to find the GDT: expose cpu_gdt directly.
We could go further and make load_gdt() pack the descriptor for us, or even
assume it means "load the current cpu's GDT" which is what it always does.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We now have cpu_init() and secondary_cpu_init() doing nothing but calling
_cpu_init() with the same arguments. Rename _cpu_init() to cpu_init() and use
it as a replcement for secondary_cpu_init().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Now we are no longer dynamically allocating the GDT, we don't need the
"cpu_gdt_table" at all: we can switch straight from "boot_gdt_table" to the
per-cpu GDT. This means initializing the cpu_gdt array in C.
The boot CPU uses the per-cpu var directly, then in smp_prepare_cpus() it
switches to the per-cpu copy just allocated. For secondary CPUs, the
early_gdt_descr is set to point directly to their per-cpu copy.
For UP the code is very simple: it keeps using the "per-cpu" GDT as per SMP,
but we never have to move.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Allocating PDA and GDT at boot is a pain. Using simple per-cpu variables adds
happiness (although we need the GDT page-aligned for Xen, which we do in a
followup patch).
[akpm@linux-foundation.org: build fix]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
remove the reporting of the constant_tsc flag from the "power management"
field in /proc/cpuinfo. The NULL value there was replaced by "" because
the former would result in a printout of [8] if the flag is set.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Change mark_tsc_unstable() so it takes a string argument, which holds the
reason the TSC was marked unstable.
This is then displayed the first time mark_tsc_unstable is called.
This should help us better debug why the TSC was marked unstable on certain
systems and allow us to make sure we're not being overly paranoid when
throwing out this troublesome clocksource.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Eliminated the arch/i386/kernel/timers in 2.6.18, use clocksoures instead.
pit_latch_buggy was referred in timers/timer_tsc.c, and currently removed.
Therefore nobody refer it.
Until 2.6.17, MediaGX's TSC works correctly. after 2.6.18, warned "TSC
appears to be running slowly. Marking it as unstable". So marked unstable
TSC when CS55x0.
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Whether a region is below 1Mb is determined by its start rather than
its end.
This hunk got erroneously dropped from a previous patch.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The PowerNow! driver for Opteron reports the number of cores
in the system, but claims to report the number of processors.
Fix this minor cosmetic bug.
Signed-off-by: Bhavana Nagendra <bhavana.nagendra@amd.com>
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
fill_powernow_table_pstate() and fill_powernow_table_fidvid() are only
defined and used for X86_POWERNOW_K8_ACPI.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Dave Jones <davej@redhat.com>
There is something wrong with this code. It needs more
testing. It is better to disable it for now because support
for some machines will be broken.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Replace obsolete pci_find_device with pci_get_device.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Support for Longhaul ver. 2 broke driver for VIA C3 Eden 600MHz with
Samuel 2 core. Processor is not able to switch frequency anymore. I
don't know much about this issue at the moment, but until (if ever) I
will know why, this part should be reversed.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AMD dual core laptops with C1E do not run the APIC timer correctly
when they go idle. Previously the code assumed this only happened
on C2 or deeper. But not all of these systems report support C2.
Use a AMD supplied snippet to detect C1E being enabled and then disable
local apic timer use.
This supercedes an earlier workaround using DMI detection of specific systems.
Thanks to Mark Langsdorf for the detection snippet.
Signed-off-by: Andi Kleen <ak@suse.de>
This reverts commit aeeddc1435, which was
half-baked and broken. It just resulted in compile errors, since
cpufreq_register_driver() still changes the 'driver_data' by setting
bits in the flags field. So claiming it is 'const' _really_ doesn't
work.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 2ff2d3d747.
Uwe Bugla reports that he cannot mount a floppy drive any more, and Jiri
Slaby bisected it down to this commit.
Benjamin LaHaise also points out that this is a big hot-path, and that
interrupt delivery while idle is very common and should not go through
all these expensive gyrations.
Fix up conflicts in arch/i386/kernel/apic.c and arch/i386/kernel/irq.c
due to other unrelated irq changes.
Cc: Stephane Eranian <eranian@hpl.hp.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Uwe Bugla <uwe.bugla@gmx.de>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Start using v2 version of Longhaul when available. It provides
voltage scaling and can use ACPI C3 state. That's curious. CPU
will not change frequency on ACPI C3 when v1 is in use, but it will
when v2 is used. Driver will return max frequency all the time if
this isn't true for all processors. There is strange thing with
mobile voltage. Looks like only Nehemiah (C3-M) supports it.
Earlier processors have different mobile VRM (in docs), but I can't
find any which is using it. Looks like all are using VRM 8.5. So
fail for non Nehemiah with mobile VRM.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Solution for small, but nasty bug: access beyond end of f_table for C7 brand.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
The old Cyrix 5520 CPU detection code relied upon the PCI layer setup being
done earlier than the CPU setup, which is no longer true. Fortunately we
know that if the processor is a MediaGX we can do type 1 pci config
accesses to check the companion chip. We thus do those directly and from
this find the 5520 and implement the workarounds for the timer problem
Original report from takada@mbf.nifty.com, I sent a proposed patch which
Takara then corrected, tested and sent back to the list on 10th January.
Submitting for merging as it seems to have been missed
AK: Changed to use pci-direct.h and fix warning for !CONFIG_PCI (later
AK: originally from akpm)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: <takada@mbf.nifty.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Fix bogus warning
linux/arch/i386/kernel/cpu/transmeta.c:12: warning: ‘cpu_freq’ may be used uninitialized in this function
Signed-off-by: Andi Kleen <ak@suse.de>
Just various new acronyms. The new popcnt bit is in the middle
of Intel space. This looks a little weird, but I've been assured
it's ok.
Also I fixed RDTSCP for i386 which was at the wrong place.
For i386 and x86-64.
Signed-off-by: Andi Kleen <ak@suse.de>
Original code doesn't write back to CCR4 register. This patch reflects a
value of a register.
Cc: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
I hope to support "classic" MediaGXm in kernel.
The DIR1 register of MediaGXm( or Geode) shows the following values for
identify CPU. For example, My MediaGXm shows 0x42.
We can read National Semiconductor's datasheet without any NDAs.
http://www.national.com/pf/GX/GXLV.html
from datasheets:
DIR1
0x30 - 0x33 GXm rev. 1.0 - 2.3
0x34 - 0x4f GXm rev. 2.4 - 3.x
0x5x GXm rev. 5.0 - 5.4
0x6x GXLV
0x7x (unknow)
0x8x Gx1
In nsc driver of X, accept 0x30 through 0x82. What will 0x7x mean?
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
All Transmeta CPUs ever produced have constant-rate TSCs.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
mtrr: fix size_or_mask and size_and_mask
This fixes two bugs in /proc/mtrr interface:
o If physical address size crosses the 44 bit boundary
size_or_mask is evaluated wrong.
o size_and_mask limits width of physical base
address for an MTRR to be less than 44 bits.
TBD: later patch had one more change, but I think that was bogus.
TBD: need to double check
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Add a notifier mechanism to the low level idle loop. You can register a
callback function which gets invoked on entry and exit from the low level idle
loop. The low level idle loop is defined as the polling loop, low-power call,
or the mwait instruction. Interrupts processed by the idle thread are not
considered part of the low level loop.
The notifier can be used to measure precisely how much is spent in useless
execution (or low power mode). The perfmon subsystem uses it to turn on/off
monitoring.
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Every file should include the headers containing the prototypes for
it's global functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Convert the PDA code to use %fs rather than %gs as the segment for
per-processor data. This is because some processors show a small but
measurable performance gain for reloading a NULL segment selector (as %fs
generally is in user-space) versus a non-NULL one (as %gs generally is).
On modern processors the difference is very small, perhaps undetectable.
Some old AMD "K6 3D+" processors are noticably slower when %fs is used
rather than %gs; I have no idea why this might be, but I think they're
sufficiently rare that it doesn't matter much.
This patch also fixes the math emulator, which had not been adjusted to
match the changed struct pt_regs.
[frederik.deweerdt@gmail.com: fixit with gdb]
[mingo@elte.hu: Fix KVM too]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Ian Campbell <Ian.Campbell@XenSource.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Zachary Amsden <zach@vmware.com>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@osdl.org: sparc64 fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change should make Longhaul more compatible with
both ver. 2 and Powersaver processors. Voltage transitions
will be done before or after frequency transition. That depends
on direction of change. I don't know how to force conservative
governor when voltage scaling is enabled, so there is only
a warning for user. Minimal voltage is calculated in different
way now because in this way more power is saved at lower
multipliers.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
This is driver for Enhanced Powersaver which is present in VIA C7
processors. Beta tested by Jorgen (jorgen (at) greven dot dk).
Thanks! Based on documentation provided by Dave Jones (Thanks!)
and C7 Eden datasheet available from www.via.com.tw. Looks like all
these C7 Eden CPU's don't have P-states in BIOS. I know that 2
p-states is low, but Jorgen finds it usefull anyway because board
is passive cooled.
There are 3 different types of C7 processors (called brands):
0. C7-M - these processors can set any maultiplier between min and
max, any voltage between min and max.
1. C7 - only min and max states are supported. Voltage is different
for min and max states.
2. Eden - only min and max states are supported. Looks like this
brand can only change multiplier. Voltage seems to be the same for
min and max frequency.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
I don't know why it is working and how, but it is working. On my
Epia transition time is by default set to 100us. I'm changing it to
200us. After that I can change frequency from min (x4.0) to max (x7.5)
without lockup. Many times.
There is a paranoid check at a beginning of a patch. Probably dead
code, but I don't have better ideas for CL10000 case at the moment.
Only way to to detect broken chip seems to be looking in log for
spurious interrupts.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
This is bug reported by John-Marc Chandonia:
> Detected 1002.292 MHz processor.
> longhaul: VIA C3 'Nehemiah B' [C5N] CPU detected. Powersaver supported.
> longhaul: Using throttling support.
> longhaul: Invalid (reserved) FSB!
FSB is correcly guessed for 999.554 MHz CPU.
To fix this error:
- ROUNDING should be range, not mask - at it's current value it is +7 -8,
- more precise calculations inside guess_fsb - 7.5x133MHz is 1000MHz now.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Now there is no need to depend on -1 in Nehemiah tables. After
previous change code is eliminating multipliers lower then 5.0
by minmult for Nehemiah A and B.
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Looks like some time ago I introduced a bug to Longhaul.
I had report that 9x133Mhz CPU is seen as 5x133MHz. So I
changed multipliers table. That was a mistake. According to
documentation table was correct. So only way to avoid 5 or 9
dilema is not use MaxMHzBR for PowerSaver 1.0. One code that
works on all processors. To do it I need also separate flag for
Nehemiah C (min = x4.0) and Nehemiah (min = x5.0).
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
This fixes the cpuinfo_cur_freq value by using the correct
find_khz_freq_from_fiddid() when the CPU uses hardware p-states.
Signed-off-by: Joachim Deguara <joachim.deguara@amd.com>
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
There is no need to have this option in Longhaul anymore.
It was for laptop with CLE266 chipset in times, when only
ACPI C3 was used to switch frequency. Now we have native
support not only for CLE266, but CN400 too. Would be good
to have support for PN266, but I can't find datasheet for it.
Looks like BIOS for CPU's faster then 1GHz don't support
ACPI C2 nor C3.
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
This reverts commit e4f0ae0ea6.
It's not wrong, but it's not right either, and everybody seems to agree
that the right fix is probably to do the ccr3 write after the ccr4 one
(and that we also should clean it up a bit). And after that we need to
really validate that all the bits that we write to ccr4 actually do
work.
The old 2.6.19 code was insane, and basically didn't change ccr4 at all
(even though it certainly looks like it was the *intent* to do so). So
let's revert the change that may fix things, just because it's not what
was actually ever tested when the code was written, even if it _was_ the
intent.
There's a discussion on http://lkml.org/lkml/2007/1/9/63 that was
started by the patch that now gets reverted, and that discussion may
well contain the proper long-term fix.
Suggested-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This workaround unnecessarily cripples functionality to work
around an errata that doesn't seem possible to hit due to
us using the automatic clock throttling in the p4 mcheck code.
See http://lkml.org/lkml/2006/10/28/148 for complete reasoning
and lack of disconsent.
Signed-off-by: Dave Jones <davej@redhat.com>
The current PDA code, which went in in post 2.6.19 has a flaw in that it
doesn't correctly cycle the GDT and %GS segment through the boot PDA,
the CPU PDA and finally the per-cpu PDA.
The bug generally doesn't show up if the boot CPU id is zero, but
everything falls apart for a non zero boot CPU id. The basically kills
voyager which is perfectly capable of doing non zero CPU id boots, so
voyager currently won't boot without this.
The fix is to be careful and actually do the GDT setups correctly.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We write back the wrong register when configuring the Geode processor.
Instead of storing to CCR4, it stores to CCR3.
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o MODPOST generates warning for i386 if kernel is compiled with
CONFIG_RELOCATABLE=y
WARNING: vmlinux - Section mismatch: reference to .init.data: from .data between 'this_cpu' (at offset 0xc05194d0) and 'cpuinfo_op'
o this_cpu pointer should be of type __cpuinitdata.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cmd.val was used uninitialized on the line below.
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This is patch that solves Ebox mini PC issue and make
FSB code more specification compilant. At start guess_fsb
function is guessing 200MHz FSB too. It is better to
make it in this way because, thanks to this function, driver
will fail for bogus FSB values caused by bogus multiplier
value. For PowerSaver processors we can't depend on Max /
MinMHzFSB because these values are only used for
PowerSaver 2.0 and 3.0. Most processors on which Longhaul
is used are PowerSaver 1.0 only. I'm changing code for older
CPU's too, but not so much as previously, and this code was
already used for Ezra. Using MinMHzBR for Ezra-T is outside
spec. It is for voltage scaling purpose and don't have to
be equal to minmult (but it is). Same for Nehemiah (it
isn't for sure). Added mult - current multiplier value.
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
ACPI PM2 register was fallback for "Longhaul ver. 1" CPU's.
My assumption that this register isn't present at
"PowerSaver" motherboards is so far true, but current code
will not work correctly in other case. There are three possible
supports: ACPI C3, PM2 and northbridge. That was my assumption
that ACPI C3 and northbridge is for PS and northbridge and PM2
is for V1. In current code we can only check if it is ACPI
support or not by port22_en. So remove port22_en and add
longhaul_flags. If USE_ACPI_C3 and USE_NORTHBRIDGE are both
clear then it means ACPI PM2 support. Also change order of
support probe from ACPI C3, PM2, northbridge to ACPI C3,
northbridge, ACPI PM2. Paranoid protection against port 0x22
cast as ACPI PM2 register. Bit 1 clear in such case - lockup
on AGP DMA. And obvious (now) fixup for do_powersaver. Use
cx->address only for ACPI C3 ("PowerSaver" processor using
PM2 support).
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
A space and a bracket are missing (and indentation is wrong).
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Fixes the oops in cpufreq_stats with acpi_cpufreq driver. The issue was
that the frequency was reported as 0 in acpi-cpufreq.c. The bug is due to
different indicies for freq_table and ACPI perf table.
Also adds a check in cpufreq_stats to check for error return from
freq_table_get_index() and avoid using the error return value.
Patch fixes the issue reported at
http://www.ussg.iu.edu/hypermail/linux/kernel/0611.2/0629.html
and also other similar issue here
http://bugme.osdl.org/show_bug.cgi?id=7383 comment 53
Signed-off-by: Dhaval Giani <dhaval.giani@gmail.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Check the correct variable and set policy->cur upon acpi-cpufreq
initialization to allow the userspace governor to be used as default.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-by: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Support for CN400 northbridge when ACPI C3 isn't available.
Tested on Epia SP13000. Thanks to Robert for testing it.
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
On board of Epia SP13000 is 10x133Mhz VIA Nehemiah. It is reported
as 10x200MHz. This patch is fixing this issue.
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Support for Core CPUs was broken in two ways in speedstep-lib: for x86_64,
we missed a MSR definition; for both x86_64 and i386, the FSB calculation
was wrong by four (it's a quad-pumped bus). Also increase the accuracy
of the calculation.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Fix the bug in duplicate states elimination in acpi-cpufreq.
Bug: Due to duplicate state elimiation in the loop earlier, the number
of valid_states can be less than perf->state_count, in which case
freq_table was ending up with some garbage/uninitialized entries
in the table.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
From: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
On some systems there could be bits set in the upper half of
the control value provided by the _PSS object. These bits are
only relevant for cpufreq drivers that use IO ports which are not
currently supported by the speedstep-centrino driver. The current
MSR oriented code assumes that upper bits are not set and thus
fails to work correctly when they are. e.g. the control and status
value equality check failed on the IBM x3650 even though the ACPI
spec allows inequality.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Dave Jones <davej@redhat.com>
We don't need a temporary variable to get the PCI revision ID.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Jones <davej@redhat.com>
There was lots of #ifdef noise in the kernel due to hotcpu_notifier(fn,
prio) not correctly marking 'fn' as used in the !HOTPLUG_CPU case, and thus
generating compiler warnings of unused symbols, hence forcing people to add
#ifdefs.
the compiler can skip truly unused functions just fine:
text data bss dec hex filename
1624412 728710 3674856 6027978 5bfaca vmlinux.before
1624412 728710 3674856 6027978 5bfaca vmlinux.after
[akpm@osdl.org: topology.c fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We do the exact same printk about a dozen lines above
with no intermediate printk's.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Here is a small patch for i386 which adds a cpufeature flag and
detection code for Intel's Branch Trace Store (BTS) feature. This
feature can be found on Intel P4 and Core 2 processors among others.
It can also be used by perfmon.
changelog:
- add CPU_FEATURE_BTS
- add Branch Trace Store detection
signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Make the needlessly global alloc_gdt() static.
(against) pda-percpu-init
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Until not so long ago, there were system log messages pointing to
inconsistent MTRR setup of the video frame buffer caused by the way vesafb
and X worked. While vesafb was fixed meanwhile, I believe fixing it there
only hides a shortcoming in the MTRR code itself, in that that code is not
symmetric with respect to the ordering of attempts to set up two (or more)
regions where one contains the other. In the current shape, it permits
only setting up sub-regions of pre-exisiting ones. The patch below makes
this symmetric.
While working on that I noticed a few more inconsistencies in that code,
namely
- use of 'unsigned int' for sizes in many, but not all places (the patch
is converting this to use 'unsigned long' everywhere, which specifically
might be necessary for x86-64 once a processor supporting more than 44
physical address bits would become available)
- the code to correct inconsistent settings during secondary processor
startup tried (if necessary) to correct, among other things, the value
in IA32_MTRR_DEF_TYPE, however the newly computed value would never get
used (i.e. stored in the respective MSR)
- the generic range validation code checked that the end of the
to-be-added range would be above 1MB; the value checked should have been
the start of the range
- when contained regions are detected, previously this was allowed only
when the old region was uncacheable; this can be symmetric (i.e. the new
region can also be uncacheable) and even further as per Intel's
documentation write-trough and write-back for either region is also
compatible with the respective opposite in the other
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Allow selected bug checks to be skipped by paravirt kernels. The two most
important are the F00F workaround (which is either done by the hypervisor,
or not required), and the 'hlt' instruction check, which can break under
some hypervisors.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Both lhype and Xen want to call the core of the x86 cpu detect code before
calling start_kernel.
(extracted from larger patch)
AK: folded in start_kernel header patch
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the pcurrent field in the PDA to implement the "current" macro. This ends
up compiling down to a single instruction to get the current task.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the cpu_number in the PDA to implement raw_smp_processor_id. This is a
little simpler than using thread_info, though the cpu field in thread_info
cannot be removed since it is used for things other than getting the current
CPU in common code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch is the meat of the PDA change. This patch makes several related
changes:
1: Most significantly, %gs is now used in the kernel. This means that on
entry, the old value of %gs is saved away, and it is reloaded with
__KERNEL_PDA.
2: entry.S constructs the stack in the shape of struct pt_regs, and this
is passed around the kernel so that the process's saved register
state can be accessed.
Unfortunately struct pt_regs doesn't currently have space for %gs
(or %fs). This patch extends pt_regs to add space for gs (no space
is allocated for %fs, since it won't be used, and it would just
complicate the code in entry.S to work around the space).
3: Because %gs is now saved on the stack like %ds, %es and the integer
registers, there are a number of places where it no longer needs to
be handled specially; namely context switch, and saving/restoring the
register state in a signal context.
4: And since kernel threads run in kernel space and call normal kernel
code, they need to be created with their %gs == __KERNEL_PDA.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
When a CPU is brought up, a PDA and GDT are allocated for it. The GDT's
__KERNEL_PDA entry is pointed to the allocated PDA memory, so that all
references using this segment descriptor will refer to the PDA.
This patch rearranges CPU initialization a bit, so that the GDT/PDA are set up
as early as possible in cpu_init(). Also for secondary CPUs, GDT+PDA are
preallocated and initialized so all the secondary CPU needs to do is set up
the ldt and load %gs. This will be important once smp_processor_id() and
current use the PDA.
In all cases, the PDA is set up in head.S, before a CPU starts running C code,
so the PDA is always available.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Clean up the espfix code:
- Introduced PER_CPU() macro to be used from asm
- Introduced GET_DESC_BASE() macro to be used from asm
- Rewrote the fixup code in asm, as calling a C code with the altered %ss
appeared to be unsafe
- No longer altering the stack from a .fixup section
- 16bit per-cpu stack is no longer used, instead the stack segment base
is patched the way so that the high word of the kernel and user %esp
are the same.
- Added the limit-patching for the espfix segment. (Chuck Ebbert)
[jeremy@goop.org: use the x86 scaling addressing mode rather than shifting]
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Zachary Amsden <zach@vmware.com>
Acked-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
