This patch adds support for the integrated RNG of the TX4939 SoC.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a sysdev to access SRAM in TXx9 SoCs via sysfs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CFE is the only supported and used bootloader on the SiByte boards,
the standalone kernel support has been never used outside Broadcom.
Remove it and make the kernel use CFE by default.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the SiByte simulation Kconfig option, which only modified
a printk.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes sure that we are not going to clear
or change the interrupt status of a GPIO interrupt
superior to 13 as this is the maximum number of GPIO
interrupt source (p.232 of the RC32434 reference manual).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CPU_CAVIUM_OCTEON is mips_r2 which is handled before the switch. This
label in the switch statement is dead code, so we remove it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Octeon has no execution hazards, so we can remove them and save an
instruction per TLB handler invocation.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some CPUs do not need ehb instructions after writing CP0 registers.
By allowing ehb generation to be overridden in
cpu-feature-overrides.h, we can save a few instructions in the TLB
handler hot paths.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Try to fold the 64-bit TLB refill handler opportunistically at the
beginning of the vmalloc path so as to avoid splitting execution flow in
half and wasting cycles for a branch required at that point then. Resort
to doing the split if either of the newly created parts would not fit into
its designated slot.
Original-patch-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The logic used to split the r4000 refill handler is liberally
sprinkled with magic numbers. We attempt to explain what they are and
normalize them against a new symbolic value (MIPS64_REFILL_INSNS).
CC: David VomLehn <dvomlehn@cisco.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add platform support for ACLC of TXx9 SoCs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for PCI and PCIe to the base Cavium OCTEON
processor support.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here we add the register definitions for the processor blocks used by
the following PCI support patch.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the integrated DMAC of the TXx9 family.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use container structure for clocksource, clock_event_device and hold a
pointer to txx9_tmr_reg in it.
This saves a few instructions in clocksource and clock_event handlers.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A wrong resolution of a merge conflict made the recently deleted wrong
error check in sb1250_set_affinity. Send the zombie back to the empire
of the undead.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit 337eb00a2c
Push BKL down into ->remount_fs()
and
commit 4aa98cf768
Push BKL down into do_remount_sb()
were uncorrectly merged.
The former removes one pair of lock/unlock_kernel(), but the latter adds
several unlock_kernel(). Finally a few unlock_kernel() calls left.
Signed-off-by: J. R. Okajima <hooanon05@yahoo.co.jp>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If a filesystem supports POSIX ACL's, the VFS layer expects the filesystem
to do POSIX ACL checks on any files not owned by the caller, and it does
this for every single pathname component that it looks up.
That obviously can be pretty expensive if the filesystem isn't careful
about it, especially with locking. That's doubly sad, since the common
case tends to be that there are no ACL's associated with the files in
question.
ext4 already caches the ACL data so that it doesn't have to look it up
over and over again, but it does so by taking the inode->i_lock spinlock
on every lookup. Which is a noticeable overhead even if it's a private
lock, especially on CPU's where the serialization is expensive (eg Intel
Netburst aka 'P4').
For the special case of not actually having any ACL's, all that locking is
unnecessary. Even if somebody else were to be changing the ACL's on
another CPU, we simply don't care - if we've seen a NULL ACL, we might as
well use it.
So just load the ACL speculatively without any locking, and if it was
NULL, just use it. If it's non-NULL (either because we had a cached
entry, or because the cache hasn't been filled in at all), it means that
we'll need to get the lock and re-load it properly.
(This commit was ported from a patch originally authored by Linus for
ext3.)
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If a filesystem supports POSIX ACL's, the VFS layer expects the filesystem
to do POSIX ACL checks on any files not owned by the caller, and it does
this for every single pathname component that it looks up.
That obviously can be pretty expensive if the filesystem isn't careful
about it, especially with locking. That's doubly sad, since the common
case tends to be that there are no ACL's associated with the files in
question.
ext3 already caches the ACL data so that it doesn't have to look it up
over and over again, but it does so by taking the inode->i_lock spinlock
on every lookup. Which is a noticeable overhead even if it's a private
lock, especially on CPU's where the serialization is expensive (eg Intel
Netburst aka 'P4').
For the special case of not actually having any ACL's, all that locking is
unnecessary. Even if somebody else were to be changing the ACL's on
another CPU, we simply don't care - if we've seen a NULL ACL, we might as
well use it.
So just load the ACL speculatively without any locking, and if it was
NULL, just use it. If it's non-NULL (either because we had a cached
entry, or because the cache hasn't been filled in at all), it means that
we'll need to get the lock and re-load it properly.
This is noticeable even on Nehalem, which does locking quite well (much
better than P4). From lmbench:
Processor, Processes - times in microseconds - smaller is better
--------------------------------------------------------------------
Host OS Mhz null null open slct fork exec sh
call I/O stat clos TCP proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ----
- before:
nehalem.l Linux 2.6.30- 3193 0.04 0.09 0.95 1.45 2.18 69.1 273. 1141
nehalem.l Linux 2.6.30- 3193 0.04 0.09 0.95 1.48 2.28 69.9 253. 1140
nehalem.l Linux 2.6.30- 3193 0.04 0.10 0.95 1.42 2.19 68.6 284. 1141
- after:
nehalem.l Linux 2.6.30- 3193 0.04 0.09 0.92 1.44 2.12 68.3 282. 1094
nehalem.l Linux 2.6.30- 3193 0.04 0.09 0.92 1.39 2.20 67.0 308. 1123
nehalem.l Linux 2.6.30- 3193 0.04 0.09 0.92 1.39 2.36 67.4 293. 1148
where you can see what appears to be a roughly 3% improvement in stat
and open/close latencies from just the removal of the locking overhead.
Of course, this only matters for files you don't own (the owner never
needs to do the ACL checks), but that's the common case for libraries,
header files, and executables. As well as for the base components of any
absolute pathname, even if you are the owner of the final file.
[ At some point we probably want to move this ACL caching logic entirely
into the VFS layer (and only call down to the filesystem when
uncached), but in the meantime this improves ext3 a bit.
A similar fix to btrfs makes a much bigger difference (15x improvement
in lmbench) due to broken caching. ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-stu300: Make driver depend on MACH_U300
i2c-s3c2410: use resource_size()
i2c: Use resource_size macro
i2c: ST DDC I2C U300 bus driver v3
i2c-bfin-twi: pull in io.h for ioremap()
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: switch to using late_initcall
radeon legacy chips: tv dac bg/dac adj updates
drm/radeon: introduce kernel modesetting for radeon hardware
drm: Add the TTM GPU memory manager subsystem.
drm: Memory fragmentation from lost alignment blocks
drm/radeon: fix mobility flags on new PCI IDs.
Authentication error abort codes should be translated to appropriate
Linux error codes, rather than all being translated to EREMOTEIO - which
indicates that the server had internal problems.
Additionally, a server shouldn't be marked unavailable and the next
server tried if an authentication error occurs. This will quickly make
all the servers unavailable to the client. Instead the error should be
returned straight to the user.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Connections that have seen a connection-level abort should not be reused
as the far end will just abort them again; instead a new connection
should be made.
Connection-level aborts occur due to such things as authentication
failures.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some architectures need to initialize SLAB caches to be able
to allocate page tables. They do that from pgtable_cache_init()
so the later should be called earlier now, best is before
vmalloc_init().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The remove member of the platform_driver bfin_t350mcqb_driver should use
__devexit_p() to refer to the remove function, and that function should
get __devexit markings. Likewise, the probe function should be marked
with __devinit and not __init.
Also, module_init() functions should be marked with __init rather than
__devinit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dma_alloc_* functions sets the memory to 0 before returning so there
is no need to call memset after the allocation. Also no point in clearing
the memory when disabling the buffer.
Signed-off-by: Vivek Kutal <vivek.kutal@azingo.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The local fbinfo/info vars in the suspend functions don't actually get
used which cause ugly gcc warnings, so drop them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add accelerated bitblt functions to s1d13xxx based video chipsets, more
specificly functions copyarea and fillrect.
It has only been tested and activated for 13506 chipsets but is expected
to work for the majority of s1d13xxx based chips. This patch also cleans
up the driver with respect of whitespaces and other formatting issues. We
update the current status comments.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>