This is a patch to allocate pgdat and per node data area for ia64. The size
for them can be calculated by compute_pernodesize().
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is to refresh node_data[] array for ia64. As I mentioned previous
patches, ia64 has copies of information of pgdat address array on each node as
per node data.
At v2 of node_add, this function used stop_machine_run() to update them. (I
wished that they were copied safety as much as possible.) But, in this patch,
this arrays are just copied simply, and set node_online_map bit after
completion of pgdat initialization.
So, kernel must touch NODE_DATA() macro after checking node_online_map().
(Current code has already done it.) This is more simple way for just
hot-add.....
Note : It will be problem when hot-remove will occur,
because, even if online_map bit is set, kernel may
touch NODE_DATA() due to race condition. :-(
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a preparatory patch to make common code for updating of NODE_DATA() of
ia64 between boottime and hotplug.
Current code remembers pgdat address in mem_data which is used at just boot
time. But its information can be used at hotplug time by moving to global
value. The next patch uses this array.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When new node becomes enable by hot-add, new sysfs file must be created for
new node. So, if new node is enabled by add_memory(), register_one_node() is
called to create it. In addition, I386's arch_register_node() and a part of
register_nodes() of powerpc are consolidated to register_one_node() as a
generic_code().
This is tested by Tiger4(IPF) with node hot-plug emulation.
Signed-off-by: Keiichiro Tokunaga <tokuanga.keiich@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Refresh NODE_DATA() for generic archs. In this case, NODE_DATA(nid) ==
node_data[nid]. node_data[] is array of address of pgdat. So, refresh is
quite simple.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the name of old add_memory() to arch_add_memory. And use node id to
get pgdat for the node at NODE_DATA().
Note: Powerpc's old add_memory() is defined as __devinit. However,
add_memory() is usually called only after bootup.
I suppose it may be redundant. But, I'm not well known about powerpc.
So, I keep it. (But, __meminit is better at least.)
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During some profiling I noticed that default_idle causes a lot of
memory traffic. I think that is caused by the atomic operations
to clear/set the polling flag in thread_info. There is actually
no reason to make this atomic - only the idle thread does it
to itself, other CPUs only read it. So I moved it into ti->status.
Converted i386/x86-64/ia64 for now because that was the easiest
way to fix ACPI which also manipulates these flags in its idle
function.
Cc: Nick Piggin <npiggin@novell.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Overloading of page fault notification with the notify_die() has performance
issues(since the only interested components for page fault is kprobes and/or
kdb) and hence this patch introduces the new notifier call chain exclusively
for page fault notifications their by avoiding notifying unnecessary
components in the do_page_fault() code path.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove VM_LOCKED before remap_pfn range from device drivers and get rid of
VM_SHM.
remap_pfn_range() already sets VM_IO. There is no need to set VM_SHM since
it does nothing. VM_LOCKED is of no use since the remap_pfn_range does not
place pages on the LRU. The pages are therefore never subject to swap
anyways. Remove all the vm_flags settings before calling remap_pfn_range.
After removing all the vm_flag settings no use of VM_SHM is left. Drop it.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert a few stragglers over to for_each_possible_cpu(), remove
for_each_cpu().
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (65 commits)
ACPI: suppress power button event on S3 resume
ACPI: resolve merge conflict between sem2mutex and processor_perflib.c
ACPI: use for_each_possible_cpu() instead of for_each_cpu()
ACPI: delete newly added debugging macros in processor_perflib.c
ACPI: UP build fix for bugzilla-5737
Enable P-state software coordination via _PDC
P-state software coordination for speedstep-centrino
P-state software coordination for acpi-cpufreq
P-state software coordination for ACPI core
ACPI: create acpi_thermal_resume()
ACPI: create acpi_fan_suspend()/acpi_fan_resume()
ACPI: pass pm_message_t from acpi_device_suspend() to root_suspend()
ACPI: create acpi_device_suspend()/acpi_device_resume()
ACPI: replace spin_lock_irq with mutex for ec poll mode
ACPI: Allow a WAN module enable/disable on a Thinkpad X60.
sem2mutex: acpi, acpi_link_lock
ACPI: delete unused acpi_bus_drivers_lock
sem2mutex: drivers/acpi/processor_perflib.c
ACPI add ia64 exports to build acpi_memhotplug as a module
ACPI: asus_acpi_init(): propagate correct return value
...
Manual resolve of conflicts in:
arch/i386/kernel/cpu/cpufreq/acpi-cpufreq.c
arch/i386/kernel/cpu/cpufreq/speedstep-centrino.c
include/acpi/processor.h
Default values for boolean and tristate options can only be 'y', 'm' or 'n'.
This patch removes wrong default for SCHED_SMT.
Signed-off-by: Jean-Luc Leger <jean-luc.leger@dspnet.fr.eu.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass the POSIX lock owner ID to the flush operation.
This is useful for filesystems which don't want to store any locking state
in inode->i_flock but want to handle locking/unlocking POSIX locks
internally. FUSE is one such filesystem but I think it possible that some
network filesystems would need this also.
Also add a flag to indicate that a POSIX locking request was generated by
close(), so filesystems using the above feature won't send an extra locking
request in this case.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
move_pages() is used to move individual pages of a process. The function can
be used to determine the location of pages and to move them onto the desired
node. move_pages() returns status information for each page.
long move_pages(pid, number_of_pages_to_move,
addresses_of_pages[],
nodes[] or NULL,
status[],
flags);
The addresses of pages is an array of void * pointing to the
pages to be moved.
The nodes array contains the node numbers that the pages should be moved
to. If a NULL is passed instead of an array then no pages are moved but
the status array is updated. The status request may be used to determine
the page state before issuing another move_pages() to move pages.
The status array will contain the state of all individual page migration
attempts when the function terminates. The status array is only valid if
move_pages() completed successfullly.
Possible page states in status[]:
0..MAX_NUMNODES The page is now on the indicated node.
-ENOENT Page is not present
-EACCES Page is mapped by multiple processes and can only
be moved if MPOL_MF_MOVE_ALL is specified.
-EPERM The page has been mlocked by a process/driver and
cannot be moved.
-EBUSY Page is busy and cannot be moved. Try again later.
-EFAULT Invalid address (no VMA or zero page).
-ENOMEM Unable to allocate memory on target node.
-EIO Unable to write back page. The page must be written
back in order to move it since the page is dirty and the
filesystem does not provide a migration function that
would allow the moving of dirty pages.
-EINVAL A dirty page cannot be moved. The filesystem does not provide
a migration function and has no ability to write back pages.
The flags parameter indicates what types of pages to move:
MPOL_MF_MOVE Move pages that are only mapped by the process.
MPOL_MF_MOVE_ALL Also move pages that are mapped by multiple processes.
Requires sufficient capabilities.
Possible return codes from move_pages()
-ENOENT No pages found that would require moving. All pages
are either already on the target node, not present, had an
invalid address or could not be moved because they were
mapped by multiple processes.
-EINVAL Flags other than MPOL_MF_MOVE(_ALL) specified or an attempt
to migrate pages in a kernel thread.
-EPERM MPOL_MF_MOVE_ALL specified without sufficient priviledges.
or an attempt to move a process belonging to another user.
-EACCES One of the target nodes is not allowed by the current cpuset.
-ENODEV One of the target nodes is not online.
-ESRCH Process does not exist.
-E2BIG Too many pages to move.
-ENOMEM Not enough memory to allocate control array.
-EFAULT Parameters could not be accessed.
A test program for move_pages() may be found with the patches
on ftp.kernel.org:/pub/linux/kernel/people/christoph/pmig/patches-2.6.17-rc4-mm3
From: Christoph Lameter <clameter@sgi.com>
Detailed results for sys_move_pages()
Pass a pointer to an integer to get_new_page() that may be used to
indicate where the completion status of a migration operation should be
placed. This allows sys_move_pags() to report back exactly what happened to
each page.
Wish there would be a better way to do this. Looks a bit hacky.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify the gen_pool allocator (lib/genalloc.c) to utilize a bitmap scheme
instead of the buddy scheme. The purpose of this change is to eliminate
the touching of the actual memory being allocated.
Since the change modifies the interface, a change to the uncached allocator
(arch/ia64/kernel/uncached.c) is also required.
Both Andrey Volkov and Jes Sorenson have expressed a desire that the
gen_pool allocator not write to the memory being managed. See the
following:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113518602713125&w=2http://marc.theaimsgroup.com/?l=linux-kernel&m=113533568827916&w=2
Signed-off-by: Dean Nelson <dcn@sgi.com>
Cc: Andrey Volkov <avolkov@varma-el.com>
Acked-by: Jes Sorensen <jes@trained-monkey.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidate the various arch-specific implementations of pxm_to_node() and
node_to_pxm() into a single generic version.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Extend the get_sb() filesystem operation to take an extra argument that
permits the VFS to pass in the target vfsmount that defines the mountpoint.
The filesystem is then required to manually set the superblock and root dentry
pointers. For most filesystems, this should be done with simple_set_mnt()
which will set the superblock pointer and then set the root dentry to the
superblock's s_root (as per the old default behaviour).
The get_sb() op now returns an integer as there's now no need to return the
superblock pointer.
This patch permits a superblock to be implicitly shared amongst several mount
points, such as can be done with NFS to avoid potential inode aliasing. In
such a case, simple_set_mnt() would not be called, and instead the mnt_root
and mnt_sb would be set directly.
The patch also makes the following changes:
(*) the get_sb_*() convenience functions in the core kernel now take a vfsmount
pointer argument and return an integer, so most filesystems have to change
very little.
(*) If one of the convenience function is not used, then get_sb() should
normally call simple_set_mnt() to instantiate the vfsmount. This will
always return 0, and so can be tail-called from get_sb().
(*) generic_shutdown_super() now calls shrink_dcache_sb() to clean up the
dcache upon superblock destruction rather than shrink_dcache_anon().
This is required because the superblock may now have multiple trees that
aren't actually bound to s_root, but that still need to be cleaned up. The
currently called functions assume that the whole tree is rooted at s_root,
and that anonymous dentries are not the roots of trees which results in
dentries being left unculled.
However, with the way NFS superblock sharing are currently set to be
implemented, these assumptions are violated: the root of the filesystem is
simply a dummy dentry and inode (the real inode for '/' may well be
inaccessible), and all the vfsmounts are rooted on anonymous[*] dentries
with child trees.
[*] Anonymous until discovered from another tree.
(*) The documentation has been adjusted, including the additional bit of
changing ext2_* into foo_* in the documentation.
[akpm@osdl.org: convert ipath_fs, do other stuff]
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sorry I didn't notice earlier, but that BUG_ON triggers for me on the
simulator. AFAICS the mask for itv is set in cpu_init(), which comes
after sal_init(). Consequently on the simulator the itv still has its
start value of zero. I've probably missed something, but I wonder why
at this stage of the boot you even need to save and restore the itv?
Signed-Off-By: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The following patch fixes a bug in the SGI Altix tioce_bus_fixup()
code. ce_dre_comp_err_addr needs to be zero'd out not ~0ULL. As
a result completion errors weren't being captured.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
struct ia64_sal_os_state has three semi-independent sections. The code
in mca_asm.S assumes that these three sections are contiguous, which
makes it very awkward to add new data to this structure. Remove the
assumption that the sections are contiguous. Define a macro to shorten
references to offsets in ia64_sal_os_state.
This patch does not change the way that the code behaves. It just
makes it easier to update the code in future and to add fields to
ia64_sal_os_state when debugging the MCA/INIT handlers.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When I tried to use PCI Express Hotplug driver on my ia64 box, I
noticed that "PCI Express support" is not even selectable on ia64.
This patch makes PCI Express support selectable.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There is an SN bug in sn_hwperf.c that affects systems with 1024n or 1024p.
The bug manifests itself 2 ways: IO interrupts are not always
targeted to the nearest node, and 2) the "cat /proc/sgi_sn/sn_topology"
commands fails with "cannot allocate memory".
The code is using the wrong macros for validating node numbers.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
One more trivial, stand-alone patch from the Xen/ia64 review. Sanity
check usage of the reserved region numbers.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This is a trivial stand-alone patch out of the Xen/ia64 patches. Add
a vmlinuz build target to be more compatible with x86-ish targets.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
MSI callouts for altix. Involves a fair amount of code reorg in sn irq.c
code as well as adding some extensions to the altix PCI provider abstaction.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Abstract IA64_FIRST_DEVICE_VECTOR/IA64_LAST_DEVICE_VECTOR since SN platforms
use a subset of the IA64 range. Implement this by making the above macros
global variables which the platform can override in it setup code.
Also add a reserve_irq_vector() routine used by SN to mark a vector's as
in-use when that weren't allocated through assign_irq_vector().
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for making ESI calls [1]. ESI stands for "Extensible SAL
specification" and is basically a way for invoking firmware
subroutines which are identified by a GUID. I don't know whether ESI
is used by vendors other than HP (if you do, please let me know) but
as firmware "backdoors" go, this seems one of the cleaner methods, so
it seems reasonable to support it, even though I'm not aware of any
publicly documented ESI calls. I'd have liked to make the ESI module
completely stand-alone, but unfortunately that is not easily (or not
at all) possible because in order to make ESI calls in physical mode,
a small stub similar to the EFI stub is needed in the kernel proper.
I did try to create a stub that would work in user-level, but it
quickly got ugly beyond recognition (e.g., the stub had to make
assumptions about how the module-loader generated call-stubs work) and
I didn't even get it to work (that's probably fixable, but I didn't
bother because I concluded it was too ugly anyhow). While it's not
terribly elegant to have kernel code which isn't actively used in the
kernel proper, I think it might be worth making an exception here for
two reasons: the code is trivially small (all that's really needed is
esi_stub.S) and by including it in the normal kernel distro, it might
encourage other OEMs to also use ESI, which I think would be far
better than each inventing their own firmware "backdoor".
The code was originally written by Alex. I just massaged and packaged
it a bit (and perhaps messed up some things along the way...).
Changes since first version of patch that was posted to mailing list:
* Export ia64_esi_call and ia64_esi_call_phys() as GPL symbols.
* Disallow building esi.c as a module for now. Building as a module
would currently lead to an unresolved reference to "sal_lock" on SMP kernels
because that symbol doesn't get exported.
* Export esi_call_phys() only if ESI is enabled.
* Remove internal stuff from esi.h and add a "proc_type" argument to
ia64_esi_call() such that serialization-requirements can be expressed (ESI
follows SAL here, where procedure calls may have to be serialized, are
MP-safe, or MP-safe andr reentrant).
[1] h21007.www2.hp.com/dspp/tech/tech_TechDocumentDetailPage_IDX/1,1701,919,00.html
Signed-off-by: David Mosberger <David.Mosberger@acm.org>
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Linux ia64 port tried to decode the processor family number
to something human-readable, but Intel brandnames don't change
synchronously with updates to the family number. Adopt a more
i386-like approach and just print the family number in decimal.
Add a new field "model name" that uses PAL_BRAND_INFO to find
the official name for the cpu, or on older systems, falls back
to using the well-known codenames (Merced, McKinley, Madison).
Signed-off-by: Tony Luck <tony.luck@intel.com>
Calls to set_irq_info in set_irq_affinity_info() is redundant because
irq_affinity mask was set just one line immediately above it. Remove
that duplicate call.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When CONFIG_PCI_MSI is set, move_irq() is an empty function, causing
grief when sys admin tries to bind interrupt to CPU.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
When building sim_defconfig, which does not define CONFIG_ACPI
arch/ia64/kernel/acpi.c:71: warning: 'acpi_madt_rev' defined but not used
really acpi.c should not be built when CONFIG_ACPI=n...
Signed-off-by: Len Brown <len.brown@intel.com>
This closes a couple holes in our attribute aliasing avoidance scheme:
- The current kernel fails mmaps of some /dev/mem MMIO regions because
they don't appear in the EFI memory map. This keeps X from working
on the Intel Tiger box.
- The current kernel allows UC mmap of the 0-1MB region of
/sys/.../legacy_mem even when the chipset doesn't support UC
access. This causes an MCA when starting X on HP rx7620 and rx8620
boxes in the default configuration.
There's more detail in the Documentation/ia64/aliasing.txt file this
adds, but the general idea is that if a region might be covered by
a granule-sized kernel identity mapping, any access via /dev/mem or
mmap must use the same attribute as the identity mapping.
Otherwise, we fall back to using an attribute that is supported
according to the EFI memory map, or to using UC if the EFI memory
map doesn't mention the region.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Bob Picco noted that 6edfba1b33
dropped the -ffreestanding compiler flag from the top level
Makefile, which allows the compiler to substitute memcpy() in
places where strcpy() is used with a known size source string.
But the ia64 memcpy() returns 0 for success, and "bytes copied"
for failure.
Fix to return the address of the destination string (like
stdlibc version, and other architectures). There are no
places where ia64 specific code makes use of the non-standard
return value.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] update sn2 defconfig
[IA64] Add mca recovery failure messages
[IA64-SGI] fix SGI Altix tioce_reserve_m32() bug
[IA64] enable dumps to capture second page of kernel stack
[IA64-SGI] - Reduce overhead of reading sn_topology
[IA64-SGI] - Fix discover of nearest cpu node to IO node
[IA64] IOC4 config option ordering
[IA64] Setup an IA64 specific reclaim distance
[IA64] eliminate compile time warnings
[IA64] eliminate compile time warnings
[IA64-SGI] SN SAL call to inject memory errors
[IA64] - Fix MAX_PXM_DOMAINS for systems with > 256 nodes
[IA64] Remove unused variable in sn_sal.h
[IA64] Remove redundant NULL checks before kfree
[IA64] wire up compat_sys_adjtimex()
Update SN2 defconfig to latest kernel and add QLA FC drivers commonly
found in SN2 boxes.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When the mca recovery code encounters a condition that makes
the MCA non-recoverable, print the reason it could not recover.
This will make it easier to identify why the recovery code did
not recover.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The following patch fixes a bug in the SGI Altix tioce_reserve_m32()
code. The bug was that we could walking past the end of the CE ASIC
32/40bit PMU ATE Buffer, resulting in a PIO Reply Error.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
MPI programs using certain debug options have a long
startup time. This was traced to a "vmalloc/vfree" in
the code that reads /proc/sgi_sn/sn_topology. On large
systems, vfree requires an IPI to all cpus to do TLB
purging.
Replace the vmalloc/vfree with kmalloc/kfree. Although
the size of the structure being allocated is unknown, it
will not not exceed 96 bytes.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix a bug that causes discovery of the nearest node/cpu to
a TIO (IO node) to fail.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Few of the notifier_chain_register() callers use __init in the definition
of notifier_call. It is incorrect as the function definition should be
available after the initializations (they do not unregister them during
initializations).
This patch fixes all such usages to _not_ have the notifier_call __init
section.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_splice() moves data to/from pipes with a file input/output. sys_vmsplice()
moves data to a pipe, with the input being a user address range instead.
This uses an approach suggested by Linus, where we can hold partial ranges
inside the pages[] map. Hopefully this will be useful for network
receive support as well.
Signed-off-by: Jens Axboe <axboe@suse.de>
SERIAL_SGI_IOC4 and BLK_DEV_SGIIOC4 depend upon SGI_IOC4, and
SERIAL_SGI_IOC3 depends upon SGI_IOC3. Currently the definitions
are out of order in the config sequence.
Fix by including drivers/sn/Kconfig immediately after SGI_SN,
upon which SGI_IOC4 and SGI_IOC3 depend.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes following compile time warnings:
drivers/pci/pci-sysfs.c: In function `pci_read_legacy_io':
drivers/pci/pci-sysfs.c:257: warning: implicit declaration of function `ia64_pci_legacy_read'
drivers/pci/pci-sysfs.c: In function `pci_write_legacy_io':
drivers/pci/pci-sysfs.c:280: warning: implicit declaration of function `ia64_pci_legacy_write'
It also fixes wrong definition of ia64_pci_legacy_write (type of `bus' is not
`pci_dev', but `pci_bus').
Signed-Off-By: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This is a trivial patch to remove following compile time warning:
arch/ia64/ia32/../../../fs/binfmt_elf.c:508: warning: 'randomize_stack_top' defined but not used
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Andrew Morton pointed out that compiler might not inline the functions
marked for inline in kprobes. There-by allowing the insertion of probes
on these kprobes routines, which might cause recursion.
This patch removes all such inline and adds them to kprobes section
there by disallowing probes on all such routines. Some of the routines
can even still be inlined, since these routines gets executed after the
kprobes had done necessay setup for reentrancy.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dmi_scan.c is arch-independent and is used by i386, x86_64, and ia64.
Currently all three arches compile it from arch/i386, which means that ia64
and x86_64 depend on things in arch/i386 that they wouldn't otherwise care
about.
This is simply "mv arch/i386/kernel/dmi_scan.c drivers/firmware/" (removing
trailing whitespace) and the associated Makefile changes. All three
architectures already set CONFIG_DMI in their top-level Kconfig files.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andrey Panin <pazke@orbita1.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'tee' of git://brick.kernel.dk/data/git/linux-2.6-block:
[PATCH] splice: add support for sys_tee()
[PATCH] splice: pass offset around for ->splice_read() and ->splice_write()
This patch modifies ia64's show_mem() to walk the vmem_map page tables and
rapidly skip forward across regions where the page tables are missing.
This prevents the pfn_valid() check from causing numerous unnecessary
page faults.
Without this patch on a 512 node 512 cpu system where every node has four
memory holes, the show_mem() call takes 1 hour 18 minutes. With this
patch, it takes less than 3 seconds.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ia64_wait_for_slaves() was changed in 2.6.17-rc1 to report the slave
state. It incorrectly assumes that all slaves are for MCA, but
ia64_wait_for_slaves() is also called from the INIT monarch handler.
The existing message is very misleading, so correct it.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Basically an in-kernel implementation of tee, which uses splice and the
pipe buffers as an intelligent way to pass data around by reference.
Where the user space tee consumes the input and produces a stdout and
file output, this syscall merely duplicates the data inside a pipe to
another pipe. No data is copied, the output just grabs a reference to the
input pipe data.
Signed-off-by: Jens Axboe <axboe@suse.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Prefetch mmap_sem in ia64_do_page_fault()
[IA64] Failure to resume after INIT in user space
[IA64] Pass more data to the MCA/INIT notify_die hooks
[IA64] always map VGA framebuffer UC, even if it supports WB
[IA64] fix bug in ia64 __mutex_fastpath_trylock
[IA64] for_each_possible_cpu: ia64
[IA64] update HP CSR space discovery via ACPI
[IA64] Wire up new syscalls {set,get}_robust_list
[IA64] 'msg' may be used uninitialized in xpc_initiate_allocate()
[IA64] Wire up new syscall sync_file_range()
Current implementations define NODES_SHIFT in include/asm-xxx/numnodes.h for
each arch. Its definition is sometimes configurable. Indeed, ia64 defines 5
NODES_SHIFT values in the current git tree. But it looks a bit messy.
SGI-SN2(ia64) system requires 1024 nodes, and the number of nodes already has
been changeable by config. Suitable node's number may be changed in the
future even if it is other architecture. So, I wrote configurable node's
number.
This patch set defines just default value for each arch which needs multi
nodes except ia64. But, it is easy to change to configurable if necessary.
On ia64 the number of nodes can be already configured in generic ia64 and SN2
config. But, NODES_SHIFT is defined for DIG64 and HP'S machine too. So, I
changed it so that all platforms can be configured via CONFIG_NODES_SHIFT. It
would be simpler.
See also: http://marc.theaimsgroup.com/?l=linux-kernel&m=114358010523896&w=2
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Take a hint from an x86_64 optimization by Arjan van de Ven and use it
for ia64. See a9ba9a3b38
Prefetch the mmap_sem, which is critical for the performance of the page fault
handler.
Note: mm may be NULL but I guess that is safe.
See 458f935527
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The OS INIT handler is loading incorrect values into cr.ifa on exit.
This shows up as a hang when resuming after an INIT that is delivered
while a cpu is in user space. Correct the value loaded into cr.ifa.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The MCA/INIT handlers maintain important state in the SAL to OS (sos)
area and in the monarch_cpu flag. Kernel debuggers (such as KDB) need
this data, and may need to adjust the monarch_cpu field so make the
data available to the notify_die hooks. Define two more events for
calling the functions on the notify_die chain.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu under
arch/ia64/kernel/.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fjitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Get rid of the manual search of _CRS, in favor of
acpi_get_vendor_resource() which is now provided by the ACPI CA. And fall
back to searching for a consumer-only address space descriptor if no
vendor-defined resource is found.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Otherwise, illegal configurations like X86_VOYAGER=y, PCI=y are
possible.
This patch also fixes the options select'ing ACPI to also select PCI.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
gcc3 thinks that a 32-bit field of a u64 type is itself a u64, so
should be printed with "%ld". gcc4 thinks it needs just "%d".
Make both versions happy by avoiding this construct.
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] ioremap() should prefer WB over UC
[IA64] Add __mca_table to the DISCARD list in gate.lds
[IA64] Move __mca_table out of the __init section
[IA64] simplify some condition checks in iosapic_check_gsi_range
[IA64] correct some messages and fixes some minor things
[IA64-SGI] fix for-loop in sn_hwperf_geoid_to_cnode()
[IA64-SGI] sn_hwperf use of num_online_cpus()
[IA64] optimize flush_tlb_range on large numa box
[IA64] lazy_mmu_prot_update needs to be aware of huge pages
This adds support for the sys_splice system call. Using a pipe as a
transport, it can connect to files or sockets (latter as output only).
From the splice.c comments:
"splice": joining two ropes together by interweaving their strands.
This is the "extended pipe" functionality, where a pipe is used as
an arbitrary in-memory buffer. Think of a pipe as a small kernel
buffer that you can use to transfer data from one end to the other.
The traditional unix read/write is extended with a "splice()" operation
that transfers data buffers to or from a pipe buffer.
Named by Larry McVoy, original implementation from Linus, extended by
Jens to support splicing to files and fixing the initial implementation
bugs.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
efi_memmap_init() collects full granules of WB memory, without
regard for whether they also support UC. So in order for ioremap()
to work for main memory, it must prefer WB mappings when possible.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add __mca_table to the DISCARD list for the gate.lds linker script to
avoid broken linker references when linking the final vmlinux file.
Also add comment to include/asm-ia64/asmmacros.h to avoid anyone else
hitting this problem in the future.
Credits to James Bottomley <James.Bottomley@SteelEye.com> for spotting
the DISCARD list in gate.lds.S
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Some condition checks on iosapic_check_gsi_range() can be omitted
because always `base <= end' is assured. This patch simplifies those
checks.
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch corrects some wrong comments and a printk message.
It also fixes some minor things, and makes all lines fit in
80 columns.
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tweak the proc setup code so things work OK with const
proc_dir_entry.proc_fops.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a for-loop in sn_hwperf_geoid_to_cnode(). It needs to loop over
num_cnodes to ensure it can still process TIO nodes in addition to
compute nodes on systems with many nodes. Interim fix until better
support for many (>265) nodes is complete.
Signed-off-by: Dean Roe <roe@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Eliminate an unnecessary -- and flawed -- use of the expensive
num_online_cpus().
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
It was reported from a field customer that global spin lock ptcg_lock
is giving a lot of grief on munmap performance running on a large numa
machine. What appears to be a problem coming from flush_tlb_range(),
which currently unconditionally calls platform_global_tlb_purge().
For some of the numa machines in existence today, this function is
mapped into ia64_global_tlb_purge(), which holds ptcg_lock spin lock
while executing ptc.ga instruction.
Here is a patch that attempt to avoid global tlb purge whenever
possible. It will use local tlb purge as much as possible. Though the
conditions to use local tlb purge is pretty restrictive. One of the
side effect of having flush tlb range instruction on ia64 is that
kernel don't get a chance to clear out cpu_vm_mask. On ia64, this mask
is sticky and it will accumulate if process bounces around. Thus
diminishing the possible use of ptc.l. Thoughts?
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Jack Steiner <steiner@sgi.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Function lazy_mmu_prot_update is also used on huge pages when it is called
by set_huge_ptep_writable, but it isn't aware of huge pages.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Acked-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The kernel's implementation of notifier chains is unsafe. There is no
protection against entries being added to or removed from a chain while the
chain is in use. The issues were discussed in this thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
We noticed that notifier chains in the kernel fall into two basic usage
classes:
"Blocking" chains are always called from a process context
and the callout routines are allowed to sleep;
"Atomic" chains can be called from an atomic context and
the callout routines are not allowed to sleep.
We decided to codify this distinction and make it part of the API. Therefore
this set of patches introduces three new, parallel APIs: one for blocking
notifiers, one for atomic notifiers, and one for "raw" notifiers (which is
really just the old API under a new name). New kinds of data structures are
used for the heads of the chains, and new routines are defined for
registration, unregistration, and calling a chain. The three APIs are
explained in include/linux/notifier.h and their implementation is in
kernel/sys.c.
With atomic and blocking chains, the implementation guarantees that the chain
links will not be corrupted and that chain callers will not get messed up by
entries being added or removed. For raw chains the implementation provides no
guarantees at all; users of this API must provide their own protections. (The
idea was that situations may come up where the assumptions of the atomic and
blocking APIs are not appropriate, so it should be possible for users to
handle these things in their own way.)
There are some limitations, which should not be too hard to live with. For
atomic/blocking chains, registration and unregistration must always be done in
a process context since the chain is protected by a mutex/rwsem. Also, a
callout routine for a non-raw chain must not try to register or unregister
entries on its own chain. (This did happen in a couple of places and the code
had to be changed to avoid it.)
Since atomic chains may be called from within an NMI handler, they cannot use
spinlocks for synchronization. Instead we use RCU. The overhead falls almost
entirely in the unregister routine, which is okay since unregistration is much
less frequent that calling a chain.
Here is the list of chains that we adjusted and their classifications. None
of them use the raw API, so for the moment it is only a placeholder.
ATOMIC CHAINS
-------------
arch/i386/kernel/traps.c: i386die_chain
arch/ia64/kernel/traps.c: ia64die_chain
arch/powerpc/kernel/traps.c: powerpc_die_chain
arch/sparc64/kernel/traps.c: sparc64die_chain
arch/x86_64/kernel/traps.c: die_chain
drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list
kernel/panic.c: panic_notifier_list
kernel/profile.c: task_free_notifier
net/bluetooth/hci_core.c: hci_notifier
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain
net/ipv6/addrconf.c: inet6addr_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain
net/netlink/af_netlink.c: netlink_chain
BLOCKING CHAINS
---------------
arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain
arch/s390/kernel/process.c: idle_chain
arch/x86_64/kernel/process.c idle_notifier
drivers/base/memory.c: memory_chain
drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list
drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list
drivers/macintosh/adb.c: adb_client_list
drivers/macintosh/via-pmu.c sleep_notifier_list
drivers/macintosh/via-pmu68k.c sleep_notifier_list
drivers/macintosh/windfarm_core.c wf_client_list
drivers/usb/core/notify.c usb_notifier_list
drivers/video/fbmem.c fb_notifier_list
kernel/cpu.c cpu_chain
kernel/module.c module_notify_list
kernel/profile.c munmap_notifier
kernel/profile.c task_exit_notifier
kernel/sys.c reboot_notifier_list
net/core/dev.c netdev_chain
net/decnet/dn_dev.c: dnaddr_chain
net/ipv4/devinet.c: inetaddr_chain
It's possible that some of these classifications are wrong. If they are,
please let us know or submit a patch to fix them. Note that any chain that
gets called very frequently should be atomic, because the rwsem read-locking
used for blocking chains is very likely to incur cache misses on SMP systems.
(However, if the chain's callout routines may sleep then the chain cannot be
atomic.)
The patch set was written by Alan Stern and Chandra Seetharaman, incorporating
material written by Keith Owens and suggestions from Paul McKenney and Andrew
Morton.
[jes@sgi.com: restructure the notifier chain initialization macros]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because pgdat_list was linked to pgdat_list in *reverse* order, (By default)
some of arch has to sort it by themselves.
for_each_pgdat has gone..for_each_online_pgdat() uses node_online_map, which
doesn't need to be sorted.
This patch removes codes for sorting pgdat.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The find_*_bit() routines are defined to work on a pointer to unsigned long.
But partial_page.bitmap is unsigned int and it is passed to find_*_bit() in
arch/ia64/ia32/sys_ia32.c. So the compiler will print warnings.
This patch changes to unsigned long instead.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide proper kprobes fault handling, if a user-specified pre/post handlers
tries to access user address space, through copy_from_user(), get_user() etc.
The user-specified fault handler gets called only if the fault occurs while
executing user-specified handlers. In such a case user-specified handler is
allowed to fix it first, later if the user-specifed fault handler does not fix
it, we try to fix it by calling fix_exception().
The user-specified handler will not be called if the fault happens when single
stepping the original instruction, instead we reset the current probe and
allow the system page fault handler to fix it up.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Acked-by: Anil S Keshavamurthy<anil.s.keshavamurthy@intel.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently kprobe handler traps only happen in kernel space, so function
kprobe_exceptions_notify should skip traps which happen in user space.
This patch modifies this, and it is based on 2.6.16-rc4.
Signed-off-by: bibo mao <bibo.mao@intel.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: "Keshavamurthy, Anil S" <anil.s.keshavamurthy@intel.com>
Cc: <hiramatu@sdl.hitachi.co.jp>
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When kretprobe probes the schedule() function, if the probed process exits
then schedule() will never return, so some kretprobe instances will never
be recycled.
In this patch the parent process will recycle retprobe instances of the
probed function and there will be no memory leak of kretprobe instances.
Signed-off-by: bibo mao <bibo.mao@intel.com>
Cc: Masami Hiramatsu <hiramatu@sdl.hitachi.co.jp>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create compat_sys_adjtimex and use it an all appropriate places.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We had a copy of the compatibility version of struct timex in each 64 bit
architecture. This patch just creates a global one and replaces all the
usages of the old ones.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Almost all users of the table addresses from the EFI system table want
physical addresses. So rather than doing the pa->va->pa conversion, just keep
physical addresses in struct efi.
This fixes a DMI bug: the efi structure contained the physical SMBIOS address
on x86 but the virtual address on ia64, so dmi_scan_machine() used ioremap()
on a virtual address on ia64.
This is essentially the same as an earlier patch by Matt Tolentino:
http://marc.theaimsgroup.com/?l=linux-kernel&m=112130292316281&w=2
except that this changes all table addresses, not just ACPI addresses.
Matt's original patch was backed out because it caused MCAs on HP sx1000
systems. That problem is resolved by the ioremap() attribute checking added
for ia64.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: "Tolentino, Matthew E" <matthew.e.tolentino@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Andi Kleen <ak@muc.de>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Check the EFI memory map so we can use the correct memory attributes for
ioremap(). Previously, we always used uncacheable access, which blows up on
some machines for regular system memory.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: "Tolentino, Matthew E" <matthew.e.tolentino@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Andi Kleen <ak@muc.de>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass the size, not a pointer to the size, to efi_mem_attribute_range().
This function validates memory regions for the /dev/mem read/write/mmap paths.
The pointer allows arches to reduce the size of the range, but I think that's
unnecessary complexity. Simplifying it will let me use
efi_mem_attribute_range() to improve the ia64 ioremap() implementation.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: "Tolentino, Matthew E" <matthew.e.tolentino@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Andi Kleen <ak@muc.de>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable DMI table parsing on ia64.
Andi Kleen has a patch in his x86_64 tree which enables the use of i386
dmi_scan.c on x86_64. dmi_scan.c functions are being used by the
drivers/char/ipmi/ipmi_si_intf.c driver for autodetecting the ports or
memory spaces where the IPMI controllers may be found.
This patch adds equivalent changes for ia64 as to what is in the x86_64
tree. In addition, I reworked the DMI detection, such that on EFI-capable
systems, it uses the efi.smbios pointer to find the table, rather than
brute-force searching from 0xF0000. On non-EFI systems, it continues the
brute-force search.
My test system, an Intel S870BN4 'Tiger4', aka Dell PowerEdge 7250, with
latest BIOS, does not list the IPMI controller in the ACPI namespace, nor
does it have an ACPI SPMI table. Also note, currently shipping Dell x8xx
EM64T servers don't have these either, so DMI is the only method for
obtaining the address of the IPMI controller.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'audit.b3' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current: (22 commits)
[PATCH] fix audit_init failure path
[PATCH] EXPORT_SYMBOL patch for audit_log, audit_log_start, audit_log_end and audit_format
[PATCH] sem2mutex: audit_netlink_sem
[PATCH] simplify audit_free() locking
[PATCH] Fix audit operators
[PATCH] promiscuous mode
[PATCH] Add tty to syscall audit records
[PATCH] add/remove rule update
[PATCH] audit string fields interface + consumer
[PATCH] SE Linux audit events
[PATCH] Minor cosmetic cleanups to the code moved into auditfilter.c
[PATCH] Fix audit record filtering with !CONFIG_AUDITSYSCALL
[PATCH] Fix IA64 success/failure indication in syscall auditing.
[PATCH] Miscellaneous bug and warning fixes
[PATCH] Capture selinux subject/object context information.
[PATCH] Exclude messages by message type
[PATCH] Collect more inode information during syscall processing.
[PATCH] Pass dentry, not just name, in fsnotify creation hooks.
[PATCH] Define new range of userspace messages.
[PATCH] Filter rule comparators
...
Fixed trivial conflict in security/selinux/hooks.c
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] New IA64 core/thread detection patch
[IA64] Increase max node count on SN platforms
[IA64] Increase max node count on SN platforms
[IA64] Increase max node count on SN platforms
[IA64] Increase max node count on SN platforms
[IA64] Tollhouse HP: IA64 arch changes
[IA64] cleanup dig_irq_init
[IA64] MCA recovery: kernel context recovery table
IA64: Use early_parm to handle mvec_name and nomca
[IA64] move patchlist and machvec into init section
[IA64] add init declaration - nolwsys
[IA64] add init declaration - gate page functions
[IA64] add init declaration to memory initialization functions
[IA64] add init declaration to cpu initialization functions
[IA64] add __init declaration to mca functions
[IA64] Ignore disabled Local SAPIC Affinity Structure in SRAT
[IA64] sn_check_intr: use ia64_get_irr()
[IA64] fix ia64 is_hugepage_only_range
* master.kernel.org:/pub/scm/linux/kernel/git/sam/kbuild: (46 commits)
kbuild: remove obsoleted scripts/reference_* files
kbuild: fix make help & make *pkg
kconfig: fix time ordering of writes to .kconfig.d and include/linux/autoconf.h
Kconfig: remove the CONFIG_CC_ALIGN_* options
kbuild: add -fverbose-asm to i386 Makefile
kbuild: clean-up genksyms
kbuild: Lindent genksyms.c
kbuild: fix genksyms build error
kbuild: in makefile.txt note that Makefile is preferred name for kbuild files
kbuild: replace PHONY with FORCE
kbuild: Fix bug in crc symbol generating of kernel and modules
kbuild: change kbuild to not rely on incorrect GNU make behavior
kbuild: when warning symbols exported twice now tell user this is the problem
kbuild: fix make dir/file.xx when asm symlink is missing
kbuild: in the section mismatch check try harder to find symbols
kbuild: fix section mismatch check for unwind on IA64
kbuild: kill false positives from section mismatch warnings for powerpc
kbuild: kill trailing whitespace in modpost & friends
kbuild: small update of allnoconfig description
kbuild: make namespace.pl CROSS_COMPILE happy
...
Trivial conflict in arch/ppc/boot/Makefile manually fixed up
alarm() calls the kernel with an unsigend int timeout in seconds. The
value is stored in the tv_sec field of a struct timeval to setup the
itimer. The tv_sec field of struct timeval is of type long, which causes
the tv_sec value to be negative on 32 bit machines if seconds > INT_MAX.
Before the hrtimer merge (pre 2.6.16) such a negative value was converted
to the maximum jiffies timeout by the timeval_to_jiffies conversion. It's
not clear whether this was intended or just happened to be done by the
timeval_to_jiffies code.
hrtimers expect a timeval in canonical form and treat a negative timeout as
already expired. This breaks the legitimate usage of alarm() with a
timeout value > INT_MAX seconds.
For 32 bit machines it is therefor necessary to limit the internal seconds
value to avoid API breakage. Instead of doing this in all implementations
of sys_alarm the duplicated sys_alarm code is moved into a common function
in itimer.c
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IPF SDM 2.2 changes definition of PAL_LOGICAL_TO_PHYSICAL to add
proc_number=-1 to get core/thread mapping info on the running processer.
Based on this change, we had better to update existing core/thread
detection in IA64 kernel correspondingly. The attached patch implements
this change. It simplifies detection code and eliminates potential race
condition. It also runs a bit faster and has better scalability especially
when cores and threads number grows up in one package.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Node number are kept in the cpu_to_node_map which is
currently defined as u8. Change to u16 to accomodate
larger node numbers.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add support in IA64 acpi for platforms that support more than
256 nodes. Currently, ACPI is limited to 256 nodes because the
proximity domain number is 8-bits.
Long term, we expect to use ACPI3.0 to support >256 nodes.
This patch is an interim solution that works with platforms
that pass the high order bits of the proximity domain in
"reserved" fields of the ACPI tables. This code is enabled
ONLY on SN platforms.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add a configuration option to allow the maximum
number of nodes to be configurable for GENERIC or SN
kernels.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
arch/ia64/sn and include/asm-ia64/sn changes required to support Tollhouse
system PCI hotplug, fixes the ia64_sn_sysctl_ioboard_get call, and introduces
the PRF_HOTPLUG_SUPPORT feature bit.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
dig_irq_init is equivalent to machvec_noop, no need to define
another empty function.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Memory errors encountered by user applications may surface
when the CPU is running in kernel context. The current code
will not attempt recovery if the MCA surfaces in kernel
context (privilage mode 0). This patch adds a check for cases
where the user initiated the load that surfaces in kernel
interrupt code.
An example is a user process lauching a load from memory
and the data in memory had bad ECC. Before the bad data
gets to the CPU register, and interrupt comes in. The
code jumps to the IVT interrupt entry point and begins
execution in kernel context. The process of saving the
user registers (SAVE_REST) causes the bad data to be loaded
into a CPU register, triggering the MCA. The MCA surfaces in
kernel context, even though the load was initiated from
user context.
As suggested by David and Tony, this patch uses an exception
table like approach, puting the tagged recovery addresses in
a searchable table. One difference from the exception table
is that MCAs do not surface in precise places (such as with
a TLB miss), so instead of tagging specific instructions,
address ranges are registers. A single macro is used to do
the tagging, with the input parameter being the label
of the starting address and the macro being the ending
address. This limits clutter in the code.
This patch only tags one spot, the interrupt ivt entry.
Testing showed that spot to be a "heavy hitter" with
MCAs surfacing while saving user registers. Other spots
can be added as needed by adding a single macro.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
include/linux/platform.h contained nothing that was actually used except
the default_idle() prototype, and is therefore removed by this patch.
This patch does the following with the platform specific default_idle()
functions on different architectures:
- remove the unused function:
- parisc
- sparc64
- make the needlessly global function static:
- arm
- h8300
- m68k
- m68knommu
- s390
- v850
- x86_64
- add a prototype in asm/system.h:
- cris
- i386
- ia64
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Patrick Mochel <mochel@digitalimplant.org>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I'm not sure of the worthiness of this idea, so please consider it an RFC.
Its key merits are:
* Reuse existing infrastructure
* Greatly tightens up the parsing of nomca
* Greatly simplifies the parsing of machvec
Addition cleanup (moving setup_mvec() to machvec.c) by Ken Chen.
Signed-Off-By: Horms <horms@verge.net.au>
Signed-Off-By: Tony Luck <tony.luck@intel.com>
This patch removes all occurances of _INLINE_ in the kernel.
With the exception of tty_flip.h, I've simply removed the inline's since
gcc should know best which functions to be inlined.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ia64_mv is initialized based on platform detected or specified.
However, there is one instantiation of each platform type. We
don't expect to switch platform vector during run time. Move
those platform specific type into init section since a copy is
made into global ia64_mv at initialization.
Also move instruction patch list into init section as well.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add init declaration to bunch of patch functions and gate
page setup function.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add init declaration to variables/functions used for memory
initialization. I don't think they would clash with memory
hotplug. If they do, please yell.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add init declaration to cpu initialization functions.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Mark init related variable and functions with appropriate
__init* declaration to mca functions.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
According to the ACPI spec, the OSPM must ignore the contents of the
Processor Local APIC/SAPIC Affinity Structure in System Resource
Affinity Table (SRAT), if its enable flag is cleared. However, ia64
linux refers all of the Processor Local APIC/SAPIC Affinity Structures
in SRAT regardless of the enable flag. This is obviously against the
ACPI spec. This patch fixes this bug.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Use the recently-added ia64_get_irr() rather than duplicating the code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
fix is_hugepage_only_range() definition to be "overlaps"
instead of "within architectural restricted hugetlb address
range". Simplify the ia64 specific code that used to use
is_hugepage_only_range() to just check which region the
address is in.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Quite a long time back, prepare_hugepage_range() replaced
is_aligned_hugepage_range() as the callback from mm/mmap.c to arch code to
verify if an address range is suitable for a hugepage mapping.
is_aligned_hugepage_range() stuck around, but only to implement
prepare_hugepage_range() on archs which didn't implement their own.
Most archs (everything except ia64 and powerpc) used the same
implementation of is_aligned_hugepage_range(). On powerpc, which
implements its own prepare_hugepage_range(), the custom version was never
used.
In addition, "is_aligned_hugepage_range()" was a bad name, because it
suggests it returns true iff the given range is a good hugepage range,
whereas in fact it returns 0-or-error (so the sense is reversed).
This patch cleans up by abolishing is_aligned_hugepage_range(). Instead
prepare_hugepage_range() is defined directly. Most archs use the default
version, which simply checks the given region is aligned to the size of a
hugepage. ia64 and powerpc define custom versions. The ia64 one simply
checks that the range is in the correct address space region in addition to
being suitably aligned. The powerpc version (just as previously) checks
for suitable addresses, and if necessary performs low-level MMU frobbing to
set up new areas for use by hugepages.
No libhugetlbfs testsuite regressions on ppc64 (POWER5 LPAR).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Original 2.6.9 patch and explanation from somewhere within HP via
bugzilla...
ia64 stores a success/failure code in r10, and the return value (normal
return, or *positive* errno) in r8. The patch also sets the exit code to
negative errno if it's a failure result for consistency with other
architectures.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
A pte may be zapped by the swapper, exiting process, unmapping or page
migration while the accessed or dirty bit handers are about to run. In that
case the accessed bit or dirty is set on an zeroed pte which leads the VM to
conclude that this is a swap pte. This may lead to
- Messages from the vm like
swap_free: Bad swap file entry 4000000000000000
- Processes being aborted
swap_dup: Bad swap file entry 4000000000000000
VM: killing process ....
Page migration is particular suitable for the creation of this race since
it needs to remove and restore page table entries.
The fix here is to check for the present bit and simply not update
the pte if the page is not present anymore. If the page is not present
then the fault handler should run next which will take care of the problem
by bringing the page back and then mark the page dirty or move it onto the
active list.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When there is no bus check, the return code should be failure, not success.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
This stuff is all in the generic ia64 kernel, and the new initcall error
reporting complains about them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Turn on CONFIG_PNPACPI. I recently removed 8250_acpi.c. All devices
previously claimed by 8250_acpi.c should now be claimed by 8250_pnp.c.
This depends on having CONFIG_PNPACPI so ACPI devices show up as PNP
devices.
All other ia64 defconfigs either have CONFIG_PNPACPI already, or
don't have 8250 support turned on at all.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The MCA recovery messages are currently KERN_DEBUG,
so they don't show up in /var/log/messages (by default).
Increase the severity to KERN_ERR, for the initial
message (and also add the physical address to this
message). Leave the successful isolation message as
KERN_DEBUG, but increase the severity when isolation
fails to KERN_CRIT.
[Russ' patch made these all KERN_CRIT]
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
The kbuild system takes advantage of an incorrect behavior in GNU make.
Once this behavior is fixed, all files in the kernel rebuild every time,
even if nothing has changed. This patch ensures kbuild works with both
the incorrect and correct behaviors of GNU make.
For more details on the incorrect behavior, see:
http://lists.gnu.org/archive/html/bug-make/2006-03/msg00003.html
Changes in this patch:
- Keep all targets that are to be marked .PHONY in a variable, PHONY.
- Add .PHONY: $(PHONY) to mark them properly.
- Remove any $(PHONY) files from the $? list when determining whether
targets are up-to-date or not.
Signed-off-by: Paul Smith <psmith@gnu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Allow sysadmin to disable all warnings about userland apps
making unaligned accesses by using:
# echo 1 > /proc/sys/kernel/ignore-unaligned-usertrap
Rather than having to use prctl on a process by process basis.
Default behaivour leaves the warnings enabled.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
beautify coding style for zeroing end of fsyscall_table entries.
Remove misleading __NR_syscall_last and add more comments.
Drop (now unneeded) "guard against failure to increase NR_syscalls"
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
arch/ia64/kernel/unaligned.c erroneously marked die_if_kernel()
with a "noreturn" attribute ... which is silly (it returns whenever
the argument regs say that the fault happened in user mode, as one
might expect given the "if_kernel" part of its name!). Thanks to
Alan and Gareth for pointing this out.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Christoph Hellwig <hch@infradead.org> pointed that there are no
in-tree uses of this. So revert 9c65cb9be6
Signed-off-by: Tony Luck <tony.luck@intel.com>
pcibios_setup() should return NULL if it handled a parameter. Since ia64
handles no parameters, it should return the string that was passed in,
not NULL. This brings ia64 into line with all other architectures that
handle no parameters.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Take advantage of kzalloc() as well as reduce the size of code generated
for the error returns in xpc_setup_infrastructure().
Signed-off-by: Jes Sorensen <jes@sgi.com>
Acked-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
unaligned_access does fetch cr.ipsr, then calls
dispatch_unaligned_handler, but dispatch_unaligned_handler fetches
cr.ipsr again, so delete the first one.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Commit 9ec4b1f356 made kprobes not compile
without module support, so just make that clear in the Kconfig file.
Also, since it's marked EXPERIMENTAL, make that dependency explicit too.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor updates to earlier patch.
- Added to documentation to add ia64 as well.
- Minor clarification on how to use disabled cpus
- used plain max instead of max_t per Andew Morton.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
It appears that if auditing is enabled, the kernel fails to
check for pending signals before returning to user mode.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Acked-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Trivial port of this feature from i386
As it stands, panic_on_oops but does nothing on ia64
Signed-Off-By: Horms <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The original ia64 udelay() was simple, but flawed for platforms without
synchronized ITCs: a preemption and migration to another CPU during the
while-loop likely resulted in too-early termination or very, very
lengthy looping.
The first fix (now in 2.6.15) broke the delay loop into smaller,
non-preemptible chunks, reenabling preemption between the chunks. This
fix is flawed in that the total udelay is computed to be the sum of just
the non-premptible while-loop pieces, i.e., not counting the time spent
in the interim preemptible periods. If an interrupt or a migration
occurs during one of these interim periods, then that time is invisible
and only serves to lengthen the effective udelay().
This new fix backs out the current flawed fix and returns to a simple
udelay(), fully preemptible and interruptible. It implements two simple
alternative udelay() routines: one a default generic version that uses
ia64_get_itc(), and the other an sn-specific version that uses that
platform's RTC.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix XPC so that it does not deliver any messages until the connected
callout has returned, as well as, prevent the disconnected callout to
occur before the disconnecting callout has returned.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The __sn_cnodeid_to_nasid array was incorrectly sized at MAX_NUMNODES.
On a large system, this array could overflow. The following patch
corrects this by defining it to MAX_COMPACT_NODES.
Signed-off-by: Dean Roe <roe@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This one falls into the "present for Andrew Morton" category to address
his wishlist for a compiler warning free build ;-)
Signed-off-by: Tony Luck <tony.luck@intel.com>
General SN2 code cleanup:
- Do not initialize global variables to zero
- Use kzalloc instead of kmalloc+memset
- Check kmalloc return values
- Do not obfuscate spin lock calls
- Remove some unused code
- Various formatting cleanups
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Remove symbol exports from ia64_ksyms.c that are already exported in
lib/string.c.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Have a facility to account for potentially hot-pluggable CPUs. ACPI doesnt
give a determinstic method to find hot-pluggable CPUs. Hence we use 2 methods
to assist.
- BIOS can mark potentially hot-pluggable CPUs as disabled in the MADT tables.
- User can specify the number of hot-pluggable CPUs via parameter
additional_cpus=X
The option is enabled only if ACPI_CONFIG_HOTPLUG_CPU=y which enables the
physical hotplug option. Without which user can still use logical onlining
and offlining of CPUs by enabling CONFIG_HOTPLUG_CPU=y
Adds more bits to cpu_possible_map for potentially hot-pluggable cpus.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Do not set cpu_possible_map for NR_CPUS when ACPI_CONFIG_HOTPLUG_CPU is set.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
MCA driver can cause panic if kernel gets a state info with no minstate.
This patch adds minstate validation before handling it.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Remove an erroneous kfree, and unlink the pcidev_info struct from the
pcidev_info list prior to free'ing the pcidev_info struct.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Registers system call for the ia64 architecture.
Reserves space for ppoll and pselect, and adds unshare at system
call number 1296.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
No platform in the community tree uses PLATFORM_MCA_HANDLERS, remove
the references.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update the comm field on the MCA handler for user tasks as well as for
verified kernel tasks. This helps to identify the task that was
running when the MCA occurred.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Print a message identifying the monarch MCA handler. Print a summary
of the status of the slave MCA cpus.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Prevent SN2 specific code to be executed on non SN2 platforms when
running a generic kernel.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There were two problems with enabling the PRINTK_TIME config
option:
1) The first calls to printk() occur before per-cpu data virtual
address is pinned into the TLB, so sched_clock() can fault.
2) sched_clock() is based on ar.itc, which may not be synchronized
across cpus.
Ken Chen started this patch, Tony Luck tinkered with it, and Jes
Sorensen perfected it.
Signed-off-by: Tony Luck <tony.luck@intel.com>
The check of (end != cp) after memparse in efi.c looks wrong to me.
The result is that we can't use mem= and max_addr= kernel parameter at
the same time.
The following patch removed the check just like other arches do.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Rewrite the SN pio_phys_xxx macros in assembly language. This
avoids issues with the Intel icc compiler. Function call
overhead is not an issue - the functions reference PIOs
and take 100's nsec to complete.
In addition, the functions should likely be in assembly
language anyway - they reference memory using physical
addressing mode. One function executes with psr.ic disabled.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
After converting the cpu physical address to shub2 physical
addressing, the address was run through TO_PHYS() which
clobbered a high node offset bit causing the BTE to fail
on shub2 nodes with large memory. This fix corrects
that problem.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
The patch implements cpu topology exportation by sysfs.
Items (attributes) are similar to /proc/cpuinfo.
1) /sys/devices/system/cpu/cpuX/topology/physical_package_id:
represent the physical package id of cpu X;
2) /sys/devices/system/cpu/cpuX/topology/core_id:
represent the cpu core id to cpu X;
3) /sys/devices/system/cpu/cpuX/topology/thread_siblings:
represent the thread siblings to cpu X in the same core;
4) /sys/devices/system/cpu/cpuX/topology/core_siblings:
represent the thread siblings to cpu X in the same physical package;
To implement it in an architecture-neutral way, a new source file,
driver/base/topology.c, is to export the 5 attributes.
If one architecture wants to support this feature, it just needs to
implement 4 defines, typically in file include/asm-XXX/topology.h.
The 4 defines are:
#define topology_physical_package_id(cpu)
#define topology_core_id(cpu)
#define topology_thread_siblings(cpu)
#define topology_core_siblings(cpu)
The type of **_id is int.
The type of siblings is cpumask_t.
To be consistent on all architectures, the 4 attributes should have
deafult values if their values are unavailable. Below is the rule.
1) physical_package_id: If cpu has no physical package id, -1 is the
default value.
2) core_id: If cpu doesn't support multi-core, its core id is 0.
3) thread_siblings: Just include itself, if the cpu doesn't support
HT/multi-thread.
4) core_siblings: Just include itself, if the cpu doesn't support
multi-core and HT/Multi-thread.
So be careful when declaring the 4 defines in include/asm-XXX/topology.h.
If an attribute isn't defined on an architecture, it won't be exported.
Thank Nathan, Greg, Andi, Paul and Venki.
The patch provides defines for i386/x86_64/ia64.
Signed-off-by: Zhang, Yanmin <yanmin.zhang@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During some testing, we got a warning about trying to allocate
memory while holding a lock. This fixes that problem.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Maintenance patch:
- Add missing __init calls
- Do not zero initialize global variables
- No need to typecast function call returns to void
- Some formatting
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
If SAL_CACHE_FLUSH drops interrupts, complain about it and fall back to
using PAL_CACHE_FLUSH instead.
This is to work around a defect in HP rx5670 firmware: when an interrupt
occurs during SAL_CACHE_FLUSH, SAL drops the interrupt but leaves it marked
"in-service", which leaves the interrupt (and others of equal or lower
priority) masked.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Somehow I doubt this comment is meant to be here anymore... It's
been floating after the L1_CACHE_SHIFT entry since before Linux
moved to bitkeeper.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Temporary patch to make pci_enable_msi() fail gracefully on altix. Will be
removed after 2.6.16 releases and the msi abstraction patches start flowing.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Redirecting interrupts using smp_affinity on altix does not work on kernels
built with CONFIG_PCI_MSI. The problem is that move_irq() turns into a noop
if MSI is built in. This patch calls move_native_irq() instead of move_irq()
to get around that.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
On SN2, MMIO writes which are issued from separate processors are not
guaranteed to arrive in any particular order at the IO hardware. When
performing such writes from the kernel this is not a problem, as a
kernel thread will not migrate to another CPU during execution, and
mmiowb() calls can guarantee write ordering when control of the IO
resource is allowed to move between threads.
However, when MMIO writes can be performed from user space (e.g. DRM)
there are no such guarantees and mechanisms, as the process may
context-switch at any time, and may migrate to a different CPU as part
of the switch. For such programs/hardware to operate correctly, it is
required that the MMIO writes from the old CPU be accepted by the IO
hardware before subsequent writes from the new CPU can be issued.
The following patch implements this behavior on SN2 by waiting for a
Shub register to indicate that these writes have been accepted. This
is placed in the context switch-in path, and only performs the wait
when the newly scheduled task changes CPUs.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
