Commit Graph

1659 Commits

Author SHA1 Message Date
Mark Lord
9d51af7bd2 sata_mv: fix MSI irq race condition
Fix a (rare) race condition in mv_interrupt() when using MSI.

The value of hpriv->main_irq_mask_addr can change on on the fly,
and without this patch we could end up writing back a stale copy
to the hardware.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-13 14:55:44 -04:00
Robert Hancock
968e594afd libata: Don't trust current capacity values in identify words 57-58
Hanno Böck reported a problem where an old Conner CP30254 240MB hard drive
was reported as 1.1TB in capacity by libata:

http://lkml.org/lkml/2009/2/13/134

This was caused by libata trusting the drive's reported current capacity in
sectors in identify words 57 and 58 if the drive does not support LBA and the
current CHS translation values appear valid. Unfortunately it seems older
ATA specs were vague about what this field should contain and a number of drives
used values with wrong byte order or that were totally bogus. There's no
unique information that it conveys and so we can just calculate the number
of sectors from the reported current CHS values.

While we're at it, clean up this function to use named constants for the
identify word values.

Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-05 07:26:10 -05:00
Tejun Heo
d6515e6ff4 libata: make sure port is thawed when skipping resets
When SCR access is available and the link is offline, softreset is
skipped as it only wastes time and some controllers don't respond very
well.  However, the skip path forgot to thaw the port, which not only
blocks further event notification from the port but also causes
repeated EH invocations on the same event on drivers which rely on
->thaw() to clear events if the IRQ is shared with another device or
port.

This problem has always been there but is uncovered by recent sata_nv
nf2/3 change which dropped hardreset support while maintaining SCR
access.  nf2/3 doesn't clear hotplug event mask from the interrupt
handler but relies on ->thaw() to clear them.  When the hardreset was
there, the reset action was never skipped and the port was always
thawed but, with the hardreset gone, ->prereset() determines that
there's no need for softreset and both ->softreset() and ->thaw() are
skipped.  This leads to stuck hotplug event in the IRQ status register
triggering hotplug event whenever IRQ is delieverd on the same IRQ.
As the controller shares the same IRQ for both ports, this happens on
every IO if one port is occpupied and the other isn't.

This patch fixes the problem by making sure that the port is thawed on
reset-skip path.

bko#11615 reports this problem.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Robert Hancock <hancockrwd@gmail.com>
Reported-by: Dan Andresan <danyer@gmail.com>
Reported-by: Arne Woerner <arne_woerner@yahoo.com>
Reported-by: Stefan Lippers-Hollmann <s.L-H@gmx.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-05 07:25:43 -05:00
Brandon Ehle
55f784c826 sata_nv: fix module parameter description
Update MODULE_PARM_DESC for ADMA to reflect the fact that the
option is disabled by default.

Signed-off-by: Brandon Ehle <azverkan@yahoo.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-05 07:25:37 -05:00
peerchen
7adbe46b92 ahci: Add the Device IDs for MCP89 and remove IDs of MCP7B to/from ahci.c
Added the Device IDs for MCP89 AHCI controller.

Removed the IDs of MCP7B because this chipset had been cancelled.

Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-05 07:25:30 -05:00
Tejun Heo
b535708146 libata: don't use on-stack sense buffer
sense_buffer is used as DMA target and shouldn't be allocated on
stack.  Use ap->sector_buf instead.  This problem is spotted by Chuck
Ebbert.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-05 07:25:10 -05:00
FUJITA Tomonori
5825627c94 libata: fix dma_unmap_sg misuse
libata passes the returned value of dma_map_sg() to
dma_unmap_sg(),which is the misuse of dma_unmap_sg().

DMA-mapping.txt says:

To unmap a scatterlist, just call:

	pci_unmap_sg(pdev, sglist, nents, direction);

Again, make sure DMA activity has already finished.

PLEASE NOTE:  The 'nents' argument to the pci_unmap_sg call must be
              the _same_ one you passed into the pci_map_sg call,
	      it should _NOT_ be the 'count' value _returned_ from the
              pci_map_sg call.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-05 07:24:57 -05:00
Alan Cox
c55af1f5ab [libata] pata_legacy: for VLB 32bit PIO don't try tricks with slop
These devices are generally used with ATA anyway and it seems that some
ATAPI will need us to issue the right number of words.  Therefore as we
can't switch mid burst on VLB devices we should only use 32bit I/O for
suitable block sizes.

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-25 15:30:23 -05:00
Alan Cox
c48052cc36 [libata] pata_amd: program FIFO
With 32bit PIO we can use the posted write buffers, but only for 32bit I/O
cycles.  This means we must disable the FIFO for ATAPI where a final 16bit
cycle may occur.

Rework the FIFO logic so that we disable the FIFO then selectively
re-enable it when we set the timings on AMD devices.  Also fix a case
where we scribbled on PCI config 0x41 of Nvidia chips when we shouldn't.

Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-25 15:30:16 -05:00
Mark Lord
6be96ac15e sata_mv: fix SoC interrupt breakage
For some reason, sata_mv doesn't clear interrupt status during init
when it's running on an SoC host adapter.  If the bootloader has
touched the SATA controller before starting Linux, Linux can end up
enabling the SATA interrupt with events pending, which will cause the
interrupt to be marked as spurious and then be disabled, which then
breaks all further accesses to the controller.

This patch makes the SoC path clear interrupt status on init like in
the non-SoC case.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-25 15:25:35 -05:00
Ondrej Zary
7ba07d16bd pata_it821x: resume from hibernation fails with RAID volume
Hibernation didn't work for me since I started to use IT8212 controller.
I did some debugging (booting with no_console_suspend init=/bin/sh).

Found that resume fails (2.6.28) with "serial number mismatch 'some
garbage' != 'some other garbage'" and "revalidation failed" messages.
That's because the controller firmware fills different serial number in
the IDENTIFY every boot.

The patch below fixes the resume simply clearing the serial number.  The
proper fix would be probably to fill in the serial number of the RAID
volume instead.  I assume that there must be something like that stored on
the drives but I don't know where.

Fix resume on pata_it821x RAID volume by clearing the serial number in
IDENTIFY data, which is otherwise different on each boot.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-25 15:22:44 -05:00
Zlatko Calusic
5955c7a2cf Add support for VT6415 PCIE PATA IDE Host Controller
Signed-off-by: Zlatko Calusic <zlatko.calusic@iskon.hr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-17 16:56:31 -08:00
Tejun Heo
7dac745b8e sata_nv: give up hardreset on nf2
Kernel bz#12176 reports that nf2 hardreset simply doesn't work.  Give
up.  Argh...

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Robert Hancock <hancockr@shaw.ca>
Reported-by: Saro <saro_v@hotmail.it>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-16 18:57:25 -05:00
Sergei Shtylyov
d1b3525b41 libata-sff: fix 32-bit PIO ATAPI regression
Commit 871af1210f (libata: Add 32bit
PIO support) has caused all kinds of errors on the ATAPI devices, so
it has been empirically proven that one shouldn't try to read/write
an extra data word when a device is not expecting it already. "Don't
do it then"; however, still use a chance to do 32-bit read/write one
last time when there are exactly 3 trailing bytes.

Oh, and stop pointlessly swapping the bytes to and fro on big-endian
machines by using io*_rep() accessors which shouldn't byte-swap.

This patch should fix the kernel.org bug #12609.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-16 18:55:56 -05:00
Samuel Thibault
5193535517 Fix my email address in qd65xx.[ch]/pata_qdi.c
The @fnac.net will be shut down within a couple of months, so fix my
email address.

Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-03 16:53:56 -08:00
Tejun Heo
9062712fa9 libata: implement HORKAGE_1_5_GBPS and apply it to WD My Book
3Gbps is often much more prone to transmission failures.  It's usually
okay to let EH handle speed down after transmission failures but some
WD My Book drives completely shutdown after certain transmission
failures and after it only power cycling can revive them.  Combined
with the fact that external drives often end up with cable assembly
which is longer than usual and more likely to have intervening gender,
this makes these drives very likely to shutdown under certain
configurations virtually rendering them unusable.

This patch implements HOARKGE_1_5_GBPS and applies it to WD My Book
such that 1.5Gbps is forced once the device is identified.

Please take a look at the following bz for related reports.

  http://bugzilla.kernel.org/show_bug.cgi?id=9913

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:04:31 -05:00
Tejun Heo
cf9a590a9e libata: add no penalty retry request for EH device handling routines
Let -EAGAIN from EH device handling routines trigger EH retry without
consuming its tries count.  This will be used to implement link SPD
horkage which requires hardreset to adjust SPD without affecting other
EH decisions.  As it bypasses the forward progress guarantee provided
by the tries count, the requester is responsible for ensuring forward
progress.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:04:19 -05:00
Tejun Heo
c2c7a89c5e libata: improve probe failure handling
When link is flaky at high speed, it isn't uncommon for a device to
repeatedly fail probing sequence early after successfully negotiating
high link speed.  This often leads to consecutive hotplug events
without successful probing.

This patch improves libata EH such that it remembers probing trials
and if there have been more than two unsuccessful trials in the past
60 seconds, slows down link speed to 1.5Gbps.

As link speed negotiation is the duty of the PHY layer proper, the
goal of this fallback mechanism is to provide the last resort when
everything else fails, which unfortunately happens not too
infrequently, so no fancy 6->3->1.5 speeding down or highest
successful transmission speed seen kind of logics (yet).

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:03:34 -05:00
Tejun Heo
a07d499b47 libata: add @spd_limit to sata_down_spd_limit()
Add @spd_limit to sata_down_spd_limit() so that the caller can specify
the SPD limit it wants.  This parameter doesn't get in the way even
when it's too low.  The closest possible limit is applied.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:03:22 -05:00
Tejun Heo
99cf610aa4 libata: clear dev->ering in smarter way
dev->ering used to be cleared together with the rest of ata_device in
ata_dev_init() which is called whenever a probing event occurs.
dev->ering is about to be used to track probing failures so it needs
to remain persistent over multiple porbing events.  This patch
achieves this by doing the following.

* Instead of CLEAR_OFFSET, define CLEAR_BEGIN and CLEAR_END and only
  clear between BEGIN and END.  ering is moved after END.  The split
  of persistent area is to allow hotter items remain at the head.

* ering is explicitly cleared on ata_dev_disable() and when device
  attach succeeds.  So, ering is persistent throug a device's life
  time (unless explicitly cleared of course) and also through periods
  inbetween disablement of an attached device and successful detection
  of the next one.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:03:17 -05:00
Tejun Heo
9913ff8abf libata: check onlineness before using SPD in sata_down_spd_limit()
sata_down_spd_limit() should check whether the link is online before
using the SPD value to determine how to limit the link speed.  Factor
out onlineness test and test it from sata_down_spd_limit().

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:03:08 -05:00
Tejun Heo
678afac678 libata: move ata_dev_disable() to libata-eh.c
ata_dev_disable() is about to be more tightly integrated into EH
logic.  Move it to libata-eh.c.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:03:00 -05:00
Tejun Heo
d89293abd9 libata: fix EH device failure handling
The dev->pio_mode > XFER_PIO_0 test is there to avoid unnecessary
speed down warning messages but it accidentally disabled SATA link spd
down during configuration phase after reset where PIO mode is always
zero.

This patch fixes the problem by moving the test where it belongs.
This makes libata probing sequence behave better when the connection
is flaky at higher link speeds which isn't too uncommon for eSATA
devices.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:02:57 -05:00
Tejun Heo
8d993eaa9c sata_nv: ck804 has borked hardreset too
While playing with nvraid, I found out that rmmoding and insmoding
often trigger hardreset failure on the first port (the second one was
always okay).  Seriously, how diverse can you get with hardreset
behaviors?  Anyways, make ck804 use noclassify variant too.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:02:38 -05:00
Randy Dunlap
5eb66fe05f libata: fix kernel-doc warnings
Fix libata kernel-doc warnings:

Warning(linux-next-20090120//drivers/ata/libata-core.c:4720): Excess function parameter 'dev' description in 'ata_qc_new'
Warning(linux-next-20090120//drivers/ata/libata-scsi.c:428): No description found for parameter 'ap'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 22:41:45 -05:00
Arjan van de Ven
f3d7f23f87 ahci: add a module parameter to ignore the SSS flags for async scanning
The SSS flag, which directs the OS to spin up one disk at a time
to not have the PSU blow out, sometimes gets set even when not needed.
The effect of this is a longer-than-needed boot time.

This patch adds a module parameter that makes the driver ignore SSS
at least as far as the parallel scan during boot is concerned...

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 22:41:39 -05:00
Mark Lord
4462254ac6 sata_mv: Fix chip type for Hightpoint RocketRaid 1740/1742
Fix chip type for the Highpoint RocketRAID 1740 and 1742 PCI cards.
These really do have Marvell 6042 chips on them, rather than the 5081 chip.

Confirmed by multiple (two) users (for the 1740), and by examining
the product photographs from Highpoint's web site.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 22:41:29 -05:00
Pasi Kärkkäinen
41137aa61c [libata] sata_sil: Fix compilation error with libata debugging enabled
I tried compiling 2.6.29-rc1 and 2.6.29-rc3 with libata debugging enabled
and got the following error:

  CC [M]  drivers/ata/sata_sil.o
drivers/ata/sata_sil.c: In function 'sil_fill_sg':
drivers/ata/sata_sil.c:327: error: 'pi' undeclared (first use in this function)
drivers/ata/sata_sil.c:327: error: (Each undeclared identifier is reported only once
drivers/ata/sata_sil.c:327: error: for each function it appears in.)
make[2]: *** [drivers/ata/sata_sil.o] Error 1
make[1]: *** [drivers/ata] Error 2
make: *** [drivers] Error 2

include/linux/libata.h has the following enabled:

#define ATA_DEBUG
#define ATA_VERBOSE_DEBUG
#define ATA_IRQ_TRAP

This fixes the compilation.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 22:38:29 -05:00
Alexander Beregalov
1737ef7598 sata_sil: Fix build breakage
Commit e57db7b (SATA Sil: Blacklist system that spins off disks during ACPI power off)
 breaks build like the following, in both cases when CONFIG_DMI set or not.

        drivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
        drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
        drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a cast

  sata_sil.c should include dmi.h

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-29 18:19:30 -08:00
Linus Torvalds
490a8d70cd Merge branch 'hibern_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'hibern_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  SATA PIIX: Blacklist system that spins off disks during ACPI power off
  SATA Sil: Blacklist system that spins off disks during ACPI power off
  SATA AHCI: Blacklist system that spins off disks during ACPI power off
  SATA: Blacklisting of systems that spin off disks during ACPI power off
  DMI: Introduce dmi_first_match to make the interface more flexible
  Hibernation: Introduce system_entering_hibernation
2009-01-27 07:50:41 -08:00
Rafael J. Wysocki
5f451fe1ab SATA PIIX: Blacklist system that spins off disks during ACPI power off
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.

To prevent this from happening we can blacklist the affected systems
using DMI information.

Blacklist HP 2510p that uses the ata_piix driver.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-27 02:15:53 -05:00
Rafael J. Wysocki
e57db7bde7 SATA Sil: Blacklist system that spins off disks during ACPI power off
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.

To prevent this from happening we can blacklist the affected systems
using DMI information.

Blacklist HP nx6325 that uses the sata_sil driver.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-27 02:15:52 -05:00
Rafael J. Wysocki
1fd684346d SATA AHCI: Blacklist system that spins off disks during ACPI power off
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.

To prevent this from happening we can blacklist the affected systems
using DMI information.

Blacklist HP nx6310 that uses the AHCI driver.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-27 02:15:51 -05:00
Rafael J. Wysocki
2a6e58d273 SATA: Blacklisting of systems that spin off disks during ACPI power off
Introduce new libata flags ATA_FLAG_NO_POWEROFF_SPINDOWN and
ATA_FLAG_NO_HIBERNATE_SPINDOWN that, if set, will prevent disks from
being spun off during system power off and hibernation, respectively
(to handle the hibernation case we need the new system state
SYSTEM_HIBERNATE_ENTER that can be checked against by libata, in
analogy with SYSTEM_POWER_OFF).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-27 02:15:49 -05:00
Phil Sutter
b98f504639 pata-rb532-cf: remove set_irq_type from finish_io
The driver has been tested without the call to set_irq_type at this
point and occurs to work fine, so it should be safe to remove it.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-27 02:13:03 -05:00
JosephChan@via.com.tw
e4d866cdea [libata] pata_via: support VX855, future chips whose IDE controller use 0x0571
It supports VX855 and future chips whose IDE controller uses PCI ID 0x0571.

Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:51:26 -05:00
Mark Lord
f9228c7ffa sata_mv: no longer experimental (v2)
Update Kconfig for sata_mv with full list of chips supported,
and (finally!) remove the "EXPERIMENTAL" designations.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:42:10 -05:00
Mark Lord
6d3c30efc9 sata_mv: msi masking fix (v2)
Enable reliable use of Message-Signaled Interrupts (MSI) in sata_mv
by masking further chip interrupts within the main interrupt handler.

Based upon a suggestion by Grant Grundler.
MSI is working reliably in all of my test systems here now.

Signed-off-by: Mark Lord <mlord@pobox.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:41:57 -05:00
Thomas Reitmayr
5d0fb2e730 sata_mv: Properly initialize main irq mask
I noticed that during initialization sata_mv.c assumes that the main
interrupt mask has its default value of 0. The function
mv_platform_probe(..) initializes a shadow irq mask with 0 assuming
that's the value of the controller's register. Now
mv_set_main_irq_mask(..) only writes the controller's register if the
new value differs from the "shadowed" value. This is fatal when trying
to disable all interrupts in mv_init_host(..), i.e. the following
function call does not write anything to the main irq mask register:

  mv_set_main_irq_mask(host, ~0, 0);

The effect I see on my machine (QNAP TS-109 II) with booting via kexec
(with Linux as a 2nd-stage boot loader) is that if the sata_mv module
was still loaded when performing kexec, then the new kernel's sata_mv
module starts up with interrupts enabled. This results in an unhandled
IRQ and breaks the boot process.

The unhandled interrupt itself might also be fixed by Lennert's patch
proposed at http://markmail.org/message/kwvzxstnlsa3s26w which I did not
try yet.

However I still propose to additionally initialize the shadow variable
with the current contents of the main irq mask register to get both in
sync and allow proper disabling the main irq mask. This fixes the
unhandled irq on my machine.

Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:37:37 -05:00
Mark Lord
cd12e1f7a2 sata_mv: remove bogus nsect restriction
Remove unneeded nsect restriction from GenII NCQ path,
and improve comments to explain why this is not a problem.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:37:00 -05:00
Mark Lord
cae6edc3b5 sata_mv: don't read hc_irq_cause
Remove silly read-modify-write sequences when clearing interrupts
in hc_irq_cause.  This gets rid of unneeded MMIO reads, resulting in
a slight performance boost when switching between EDMA and non-EDMA
modes (eg. for cache flushes).

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:36:53 -05:00
Mark Lord
b0bccb18bc sata_mv: fix 8-port timeouts on 508x/6081 chips
Fix a longstanding bug for the 8-port Marvell Sata controllers (508x/6081),
where accesses to the upper 4 ports would cause lost-interrupts / timeouts
for the lower 4-ports.  With this patch, the 6081 boards should finally be
reliable enough for mainstream use with Linux.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:36:41 -05:00
Tejun Heo
2d775708bc sata_nv: fix MCP5x reset
MCP5x family of controllers seem to share much more with nf2's as far
as reset protocol is concerned.  It requires heardreset to get the PHY
going and classfication code report after hardreset is unreliable.
Create a new board type MCP5x and use noclassify hardreset.  SWNCQ is
modified to inherit from this new type.

This fixes hotplug regression reported in kernel bz#12351.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:36:31 -05:00
Tejun Heo
e8caa3c70e sata_nv: rename nv_nf2_hardreset()
nv_nf2_hardreset() will be used by other flavors too.  Rename it to
nv_noclassify_hardreset().

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:36:29 -05:00
Tejun Heo
b919930c34 libata: set NODEV_HINT for 0x7f status
Asus Pundit-R with atiixp controller has the second port missing and,
very unusually, its status is stuck at 0x7f and all others at 0.  This
meanst that it fails TF access test but gets detected as a disk due to
classification code check and then evades polling IDENTIFY presence
detection thanks to the missing BSY in the status value causing
excessive delays during boot.

This patch makes libata-sff HSM set NODEV_HINT if the status is 0x7f
to make polling IDENTIFY presence detection work for these machines.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:36:26 -05:00
Tejun Heo
80ee6f54f5 libata-sff: fix incorrect EH message
The EH message for NODEV_HINT path was describing the opposite
condition.  Fix it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:36:16 -05:00
Michal Sojka
e4ac522bd7 sata_fsl: Return non-zero on error in probe()
while I was looking over kernel sources I've found this small bug.

Formerly, zero was returned even if an error happened.

Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:23:58 -05:00
Andrew Morton
bc42b24e6e drivers/ata/pata_ali.c: s/isa_bridge/ali_isa_bridge/ to fix alpha build
drivers/ata/pata_ali.c:44: error: static declaration of 'isa_bridge' follows non-static declaration
arch/alpha/include/asm/pci.h:274: error: previous declaration of 'isa_bridge' was here

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:23:43 -05:00
David Daney
3c929c6f5a libata: New driver for OCTEON SOC Compact Flash interface (v7).
Cavium OCTEON processor support was recently merged, so now we have
this CF driver for your consideration.

Most OCTEON variants have *no* DMA or interrupt support on the CF
interface so for these, only PIO is supported.  Although if DMA is
available, we do take advantage of it.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:23:39 -05:00
David Daney
3ada9c1264 libata: Add another column to the ata_timing table.
The forthcoming OCTEON SOC Compact Flash driver needs an additional
timing value that was not available in the ata_timing table.  I add a
new column for dmack_hold time.  The values were obtained from the
Compact Flash specification Rev 4.1.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:23:37 -05:00