- Implement HW ECC support,
- Provide read_buf() and write_buf() routines using memcpy
- Use on-flash bad block table
- Fix module refcounting
- Avoid read/modify/write in hwcontrol()
- Minor cosmetic fixes
Partly based on code and ideas from Tom Sylla <tom.sylla@amd.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
One Block of the NAND Flash Array memory is reserved as
a One-Time Programmable Block memory area.
Also, 1st Block of NAND Flash Array can be used as OTP.
The OTP block can be read, programmed and locked using the same
operations as any other NAND Flash Array memory block.
OTP block cannot be erased.
OTP block is fully-guaranteed to be a valid block.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
There's some problem with write oob in serveral platform.
So we write oob with oobsize aligned (16bytes) instead of 3 bytes (from {2,
3})
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Some free byte positions at onenand_oob_64 were wrong. This was also
reported by Christian Lehne. 3 byte slots are at 2+16*i and 2 byte
slots at 14+16*i.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Default values for boolean and tristate options can only be 'y', 'm' or 'n'.
This patch removes wrong default for MTD_PCMCIA_ANONYMOUS.
Signed-off-by: Jean-Luc Leger <jean-luc.leger@dspnet.fr.eu.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Oops. Stupid StudlyCaps. Again.
This driver is doubly-deprecated because is was subsumed into doc2000.c
and _also_ we want people to start using the new NAND wrapper for these
devices anyway. But ISTR there was still one person using it because
something didn't work for them. Must chase that up and then I can kill
this.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This lacks hardware ECC support and a few optimisations we're going to
want fairly soon, but it works well enough to mount and use JFFS2.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
After dwmw2 let me know it ought to be done, I rewrote the physmap map
driver to be a platform driver. I know zilch about the driver model,
so I probably botched it in some way, but I've done some tests on an
ixp23xx board which uses physmap, and it all seems to work.
In order to not break existing physmap users, I've added some compat
code that will instantiate a platform device iff CONFIG_MTD_PHYSMAP_LEN
is defined and != 0. Also, I've changed the default value for
CONFIG_MTD_PHYSMAP_LEN to zero, so that people who inadvertently
compile in physmap (or new, platform-style, users of physmap) don't get
burned.
This works pretty well -- the new physmap driver is a drop-in replacement
for the old one, and works on said ixp23xx board without any code changes
needed. (This should hold as long as users don't touch 'physmap_map'
directly.)
Once all physmap users have been converted to instantiate their own
platform devices, the compat code can go. (Or we decide that we can
change all the in-tree users at the same time, and never merge the
compat code.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch fixes the issues with multiple irqs.
I am resending based on feedback. I decoupled the dma mask for
consistent memory and fixed leak with multiple irq in error path.
Thanks to Manfred for catching the spin lock problem.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Fixes Rhine I cards disclosing fragments of previously transmitted frames
in new transmissions.
Before transmission, any socket buffer (skb) shorter than the ethernet
minimum length of 60 bytes was zero-padded. On Rhine I cards the data can
later be copied into an aligned transmission buffer without copying this
padding. This resulted in the transmission of the frame with the extra
bytes beyond the provided content leaking the previous contents of this
buffer on to the network.
Now zero-padding is repeated in the local aligned buffer if one is used.
Following a suggestion from the via-rhine maintainer, no attempt is made
here to avoid the duplicated effort of padding the skb if it is known that
an aligned buffer will definitely be used. This is to make the change
"obviously correct" and allow it to be applied to a stable kernel if
necessary. There is no change to the flow of control and the changes are
only to the Rhine I code path.
The patch has run on an in-service Rhine-I host without incident. Frames
shorter than 60 bytes are now correctly zero-padded when captured on a
separate host. I see no unusual stats reported by ifconfig, and no unusual
log messages.
Signed-off-by: Craig Brind <craigbrind@gmail.com>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Sat, Mar 11, Olaf Hering wrote:
> Why is the /sys/class/net/eth0/device symlink not created for the
> mv643xx_eth driver? Does this work for other platform device drivers?
> Seems to work for the ps2 keyboard at least.
The SET_NETDEV_DEV has to be done before a call to register_netdev. With
the new patch below, the device symlink for the platform device was
created. Unfortunately, after the 4 ls commands, the network connection
died. No idea if the box crashed or if something else broke, lost remote
access.
Provide sysfs 'device' in /class/net/ethN Also, set module owner field,
like pcnet32 driver does.
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ipath: tidy up white space in a few files
IB/ipath: fix label name in interrupt handler
IB/ipath: improve sparse annotation
IB/ipath: simplify IB timer usage
IB/ipath: simplify RC send posting
IB/ipath: prevent hardware from being accessed during reset
IB/ipath: fix verbs registration
IB/ipath: change handling of PIO buffers
IB/ipath: iterate over correct number of ports during reset
IB/ipath: set up 32-bit DMA mask if 64-bit setup fails
IB/ipath: fix race with exposing reset file
IB/mthca: Fix offset in query_gid method
Fix genrtc's read() routine for 64-bit platforms. Current gen_rtc_read()
stores 64bit integer and returns 8 even if an user tried to read a 32bit
integer.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make rtc-dev work well on 64-bit platforms with 32-bit userland. On those
platforms, users might try to read 32-bit integer value. This patch make
rtc-dev's read() work well for both "int" and "long" size. This tweak is came
from genrtc driver.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As pointed out by Paulo Marques <pmarques@grupopie.com> MAX_IPD_TIME is by
a factor of ten too small. Since this means that we allow ten times more
IPDs in the intended time frame this could result in a cpu check stop of a
physical cpu.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently loading the ioc3 as a module will cause the ports to be numbered
in reverse order. This mod maintains the proper order of cards for port
numbering.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When retrying a failed BIO_RW_BARRIER request, we need to keep the reference
in ->nr_pending over the whole retry. Currently, we only hold the reference
if the failed request is the *last* one to finish - which is silly, because it
would normally be the first to finish.
So move the rdev_dec_pending call up into the didn't-fail branch. As the rdev
isn't used in the later code, calling rdev_dec_pending earlier doesn't hurt.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the test for 'do barrier work' down a bit so that if the first write to a
raid1 is a BIO_RW_BARRIER write, the checking done by superblock writes will
cause the right thing to happen.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because that is what you get if a BIO_RW_BARRIER isn't supported!
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to hold a reference to rdevs while reading and writing to attempt to
correct read errors. This reference must be taken under an rcu lock.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should add to the counter for the rdev *after* checking if the rdev is
NULL!!!
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Names that are the opposite of their intended meanings are not so helpful.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The reset code now turns off the PRESENT flag during a reset, so that
other code won't attempt to access a device that's in mid-reset.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remember when the verbs layer unregisters from the lower-level code.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Different ipath hardware types have different numbers of buffers
available, so we decide on the counts ourselves unless we are specifically
overridden with a module parameter.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some systems do not set up 64-bit maps on systems with 2GB or less of
memory installed, so we have to fall back to trying a 32-bit setup.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We were accidentally exposing the "reset" sysfs file more than once
per device.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
GuidInfo records have 8 byte GUIDs in them, so an index should be
multiplied by 8 to get an offset. mthca_query_gid() was incorrectly
multiplying by 16.
Noticed by Leonid Keller <leonid@mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TG3]: Update version and reldate
[TG3]: Fix bug in nvram write
[TG3]: Add reset_phy parameter to chip reset functions
[TG3]: Reset chip when changing MAC address
[TG3]: Add phy workaround
[TG3]: Call netif_carrier_off() during phy reset
[IPV6]: Fix race in route selection.
[XFRM]: fix incorrect xfrm_policy_afinfo_lock use
[XFRM]: fix incorrect xfrm_state_afinfo_lock use
[TCP]: Fix unlikely usage in tcp_transmit_skb()
[XFRM]: fix softirq-unsafe xfrm typemap->lock use
[IPSEC]: Fix IP ID selection
[NET]: use hlist_unhashed()
[IPV4]: inet_init() -> fs_initcall
[NETLINK]: cleanup unused macro in net/netlink/af_netlink.c
[PKT_SCHED] netem: fix loss
[X25]: fix for spinlock recurse and spinlock lockup with timer handler
* git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: make EVIOCGSND return meaningful data
Input: ressurect EVIOCGREP and EVIOCSREP
Input: psmouse - fix new device detection logic
Input: move input_device_id to mod_devicetable.h
Input: allow using several chords for braille
Input: allow passing NULL to input_free_device()
Input: spitzkbd - fix the reversed Address and Calender keys
Input: ads7846 - improve filtering for thumb press accuracy
Input: ads7846 - report 0 pressure value along with pen up event
Input: ads7846 - handle IRQs that were latched during disabled IRQs
Input: ads7846 - miscellaneous fixes
Input: ads7846 - use msleep() instead of udelay() in suspend
Input: ads7846 - debouncing and rudimentary sample filtering
Input: ads7846 - power down ADC a bit later
Input: ads7846 - add pen_down sysfs attribute
Input: wistron - add support for Fujitsu N3510
Input: wistron - add signature for Amilo M7400
* git://git.kernel.org/pub/scm/linux/kernel/git/perex/alsa: (22 commits)
[ALSA] via82xx - Use DXS_SRC as default for VIA8235/8237/8251 chips
[ALSA] hda-codec - Add model entry for ASUS Z62F
[ALSA] PCMCIA sound devices shouldn't depend on ISA
[ALSA] hda-codec - Fix capture from line-in on VAIO SZ/FE laptops
[ALSA] Fix Oops at rmmod with CONFIG_SND_VERBOSE_PROCFS=n
[ALSA] PCM core - introduce CONFIG_SND_PCM_XRUN_DEBUG
[ALSA] adding __devinitdata to pci_device_id
[ALSA] add __devinitdata to all pci_device_id
[ALSA] hda-codec - Add codec id for AD1988B codec chip
[ALSA] hda-codec - Add model entry for ASUS M9 laptop
[ALSA] pcxhr - Fix a compiler warning on 64bit architectures
[ALSA] via82xx: tweak VT8251 workaround
[ALSA] intel8x0 - Disable ALI5455 SPDIF-input
[ALSA] via82xx: add support for VIA VT8251 (AC'97)
[ALSA] Fix typos and add information about Jack support to Audiophile-Usb.txt
[ALSA] Fix double free in error path of miro driver
[ALSA] hda-codec - Add entry for Epox EP-5LDA+ GLi
[ALSA] sound/pci/: remove duplicate #include's
[ALSA] hda-codec - Use model 'hp' for all HP laptops with AD1981HD
[ALSA] continue on IS_ERR from platform device registration
...