Any connection in 11g/a is very latency sensitive and
we need to vote for a higher DDR frequency than in
the other phy modes.
Identify the number of latency sensitive connections
in STA mode and vote for higher DDR frequency for the
latency sensitive cases.
Change-Id: I2ce20b2b40213bde52211eae659c9673c6e0d305
CRs-fixed: 2695045
Wlan driver is built to support different chipset, while on QC platform
function driver and device probe happened in CNSS platform driver,
so when loading wlan driver, need parse supported id list to platform
driver to check if this wlan driver can be loaded in current platform.
Change-Id: I91e87ffa32d77e2bab15fca09514cdefb1075c71
CRs-Fixed: 2644233
Initialize pld_uevent_data variable to zero, as the driver
expects zero data if there is no fw down data sent from
platform driver.
Change-Id: I24c3fa459207d254f7b579a387985eca06466447
CRs-fixed: 2658683
Add code to handle hang event data and length received
from platform driver through uevent.
Change-Id: Ie4acf55cd7d2e602ad10eedbdeed045acfd85f56
CRs-fixed: 2650831
For QCN7605 chip, FW team need athdiag tool to operate FW
information. Host driver need to pass the command and result
between athdiag tool and FW.
Change-Id: Ib3f4498ba560b2b76ec6939760535069777b972c
CRs-Fixed: 2595510
Add pld API to get audio timestamp needed in FTM wlan
timesync feature to synchronise the audio clocks of
master and slave devices
Change-Id: I6f08e33904e26728492286f516ce5a8074afd1ea
CRs-Fixed: 2616917
Previously vdev trans will be rejected if psoc in trans. but
it causes issue when __hdd_psoc_idle_shutdown is in psoc trans,
if ifconfig comes here, the ifconfig will fail.
Add checking if psoc trans in driver recovering and unloading,
if yes, it will be safe to reject vdev trans, otherwise, we should
let vdev trans waiting for psoc trans.
At the same time, we also need to make sure driver state has been
set before psoc trans when unloading.
Change-Id: Ic47eebef76b8eadc90780b74f75d4ebef73b822d
CRs-Fixed: 2601435
Function ol_txrx_hl_tdls_flag_reset will call function
ol_txrx_get_vdev_from_vdev_id, it will return NULL vdev
because ol_txrx_hl_tdls_flag_reset is called before
TAILQ_INSERT_TAIL(vdev).
So, move it after TAILQ_INSERT_TAIL(vdev).
Redefinition of 'pld_pcie_register_driver' when
CONFIG_PLD_PCIE_CNSS not defined. For Hastings WHUNT,
HIF_PCI is defined but CONFIG_PLD_PCIE_CNSS is not defined.
So, replace CONFIG_PLD_PCIE_CNSS by HIF_PCI and
CONFIG_PLD_PCIE_FW_SIM.
Change-Id: I05e58516efe6a9a445168a27df9e0cfc9de2e50c
CRs-Fixed: 2589802
Don't set unload flags earlier before unregister_driver when driver
unloading to avoid runtime resume failure. And set this flags earlier
before wait_for_ops in the pld_pcie_remove to give chance SSR will be
skipped if unloading is in progress.
Change-Id: I084db32b436148932a2a90e3e1dcb1122f4303b5
CRs-Fixed: 2589413
Currently pld_lock/unlock_reg_window APIs don't support
WHUNT simulation bus types and treated as error.
Add support for WHUNT simulation buses in lock/unlock
register window APIs.
Change-Id: I1e82d822becaadc9592b693e6ab20331ecb9cbc2
The register window needs to be configed properly before accessing
any larger than 4K range PCIe registers. Expose the lock in PLD to
avoid race condition when both platform and host drivers
try to config it.
Change-Id: Icd3df3d4d2cc2ecc3df608e7b767a3e654b94500
CRs-Fixed: 2549887
WHUNT is host unit testing framework which simulates
firmware. Add a PLD wrapper layer for this virtual device.
Change-Id: I1d09b8a18a25b414b0c1d56723cc5687f2bfe297
Modem block/unblock shutdown callbacks are added to synchronize
modem shutdown when the driver is in deinit sequence.
With new changes everything is synchronized via the platform driver,
So remove the the block/unblock shutdown callback's.
Change-Id: If66eed5b51bbce64f024edf49e37a21b222a6a4c
CRs-Fixed: 2489733
Protect pld_del_dev function as part of psoc transaction
to avoid race condition with pld_deinit.
Change-Id: I3180801308b9a5e85822fb8d8bc04a9ecb42b347
CRs-Fixed: 2530822
These APIs can be used to send data request to firmware over QMI
as well as receive response from firmware.
Change-Id: I186d4c53e846af028b5ea75079027217af1580b4
CRs-fixed: 2517225
If without CNSS2 module, CNSS_RECOVERY undeclared issue will occur.
Move function pld_sdio_uevent() to CONFIG_PLD_SDIO_CNSS2 macro,
because it is active only when CONFIG_PLD_SDIO_CNSS2 is defined.
Change-Id: Ic86260ccefad820c47257a8ccbcfae9194b78b8f
CRs-Fixed: 2530671
Platform driver is still doing MHI cleanup at the current location of
clearing the recovery flag. Clear it after platform driver callback.
Change-Id: Ifa81950790fa3d2704ed1aed85301a99c6383470
CRs-Fixed: 2526873
Add separate Coldboot calibration mode (10) for Coldboot Calibration
done during FTM Mode in PLD.
Change-Id: I7e4bb5209d87613bb49a0a958d8e691c73fdcfe1
CRs-Fixed: 2499766
The SDIO HIF for QCN7605 requires to use the SDIO Abstraction Layer.
Used the SDIO CNSS2 PLD layer api's to interface with SDIO AL
Change-Id: I839a580941e4651e3dcff4f87cda26cc567687fc
CRs-Fixed: 2275631
Add additional bandwidth level for "very high" bandwidth. As per the
default configuration if the total number of tx/rx packets exceeds
bus_bw_very_high_threshold, the bus bandwidth requirement is designated
as PLD_BUS_WIDTH_VERY_HIGH and PLD API is called with this value.
Default value of 7000 is chosen for bus_bw_very_high_threshold, which
amounts to 820Mbps of throughput considering a 1500 byte packet and
100ms bandwidth timer interval.
Change-Id: I3bd904429a02ec4935ba12da7c2cfd37eec738ed
CRs-Fixed: 2489362
Bus bandwidth logic uses PLD_BUS_WIDTH_NONE to vote if the packet
threshold is less than bus_bw_low_threshold. The same vote is used for
system suspend too. Add a new state for bus bandwidth logic to vote for
idle state.
Change-Id: I62ca6fff84a01083001db360f56344a05fb955db
CRs-Fixed: 2484003
Provide platform driver interface for idle restart/shutdown for
PCIe bus in PLD. Remove PCIe power off call for discrete PCIe bus
enabled SoC such that platform driver can execute proper SoC power
off sequence.
Change-Id: If08186247e89a4182cadbf83817dce4f02654ecc
CRs-Fixed: 2431419
Add PLD API in order to check if DRV (Direct Resource Vote) subsystem
is connected or not.
Change-Id: I3b600b0760e27c7111320088034c555aee4ff773
CRs-fixed: 2452039
Populate WLAN device version related info along with other SOC info
in pld_get_soc_info() API.
Change-Id: Ie0e862c6755d10fbc80b11fbf39d004fafcfd9af
CRs-fixed: 2437413
Serialize psoc interface inactivity idle shutdown and restart via PLD
such that platfrom driver can serialize psoc idle shutdown and restart
to driver unload and SSR events to avoid any race conditions.
Change-Id: Ibac40158ad5b94468b09c53eaf7f3d9a3cb8badf
CRs-Fixed: 2430868
Introduces a new build flag 'DYNAMIC_SINGLE_CHIP':
If DYNAMIC_SINGLE_CHIP is defined, which means there
are multiple possible drivers, but only requires one
instance of driver at a time. In such case, leave
MULTI_IF_NAME undefined, no matter what the module
name is, only prepend DYNAMIC_SINGLE_CHIP to names
of firmware/mac/ini files.
Take path of driverdump and ini file for example:
If both MULTI_IF_NAME and DYNAMIC_SINGLE_CHIP are not
defined, the paths are:
driverdump: '/proc/debugdriver/driverdump'
ini: '/<fw_root>/wlan/qca_cld/WCNSS_qcom_cfg.ini'
If DYNAMIC_SINGLE_CHIP is defined as 'qca6174':
driverdump: '/proc/debugdriver/driverdump'
ini: '/<fw_root>/wlan/qca_cld/qca6174/WCNSS_qcom_cfg.ini'
If MULTI_IF_NAME is defined as 'qca6174' and
DYNAMIC_SINGLE_CHIP is not defined:
driverdump: '/proc/debugdriverqca6174/driverdump'
ini: '/<fw_root>/wlan/qca_cld/qca6174/WCNSS_qcom_cfg.ini'
On LA platform, DYNAMIC_SINGLE_CHIP is controlled by
TARGET_WLAN_CHIP and TARGET_MULTI_WLAN:
If more than one WLAN devices are enabled in TARGET_WLAN_CHIP,
and TARGET_MULTI_WLAN is not set to 'true',
DYNAMIC_SINGLE_CHIP will be set to the device name, to
avoid name conflicts of firmware/mac/ini files;
meanwhile, MODNAME is set to 'wlan', then paths for
debugging are not changed.
Otherwise, MULTI_IF_NAME will be defined if requires
multiple instances of driver.
Change-Id: I22ed34d80d3540451bf8b891243c6cdac5a73d7e
CRs-Fixed: 2402432
Currently there is no way to find out PD Restart indication,
so platform driver has added an API to differentiate PD Restart
from SSR. Using this API in shutdown notify handler, sending
message to IPA to do required cleanup.
Change-Id: I9d07c6fc573b6db1c7d0c1b7c99f325e22fe81cd
CRs-Fixed: 2436036
Add update_status callback to pld usb which will be called by
CNSS to update WLAN FW status(FW-DOWN, RECOVERY)
Change-Id: I159e09eac8bdb75525c64e7b42c3315141ec1f8d
CRs-Fixed: 2430265
