This patch introduces users of the round_jiffies() function in the
networking code.
These timers all were of the "about once a second" or "about once
every X seconds" variety and several showed up in the "what wakes the
cpu up" profiles that the tickless patches provide. Some timers are
highly dynamic based on network load; but even on low activity systems
they still show up so the rounding is done only in cases of low
activity, allowing higher frequency timers in the high activity case.
The various hardware watchdogs are an obvious case; they run every 2
seconds but aren't otherwise specific of exactly when they need to
run.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We clear the unused parts of the SACK cache, This prevents us from mistakenly
taking the cache data if the old data in the SACK cache is the same as the data
in the SACK block. This assumes that we never receive an empty SACK block with
start and end both at zero.
Signed-off-by: Baruch Even <baruch@ev-en.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move DSACK code outside the SACK fast-path checking code. If the DSACK
determined that the information was too old we stayed with a partial cache
copied. Most likely this matters very little since the next packet will not be
DSACK and we will find it in the cache. but it's still not good form and there
is little reason to couple the two checks.
Since the SACK receive cache doesn't need the data to be in host order we also
remove the ntohl in the checking loop.
Signed-off-by: Baruch Even <baruch@ev-en.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only advance the SACK fast-path pointer for the first block, the
fast-path assumes that only the first block advances next time so we
should not move the cached skb for the next sack blocks.
Signed-off-by: Baruch Even <baruch@ev-en.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both aux data and sockaddr tries to use the same buffer which
obviously doesn't work. We just happen to have 4 bytes free in
the skb->cb if you take away the maximum length of sockaddr_ll.
That's just enough to store the one piece of info from aux data
that we can't generate at recvmsg(2) time.
This is what the following patch does.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is needed to make ISC's DHCP server (and probably other
DHCP servers/clients using AF_PACKET) to be able to serve another
client on the same Xen host.
The problem is that packets between different domains on the same
Xen host only have partial checksums. Unfortunately this piece of
information is not passed along in AF_PACKET unless you're using
the mmap interface. Since dhcpd doesn't support packet-mmap, UDP
packets from the same host come out with apparently bogus checksums.
This patch adds a mechanism for AF_PACKET recvmsg(2) to return the
status along with the packet. It does so by adding a new cmsg that
contains this information along with some other relevant data such
as the original packet length.
I didn't include the time stamp information since there is already
a cmsg for that.
This patch also changes the mmap code to set the CSUMNOTREADY flag
on all packets instead of just outoing packets on cooked sockets.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do this even for non-blocking sockets. This avoids the silly -EAGAIN
that applications can see now, even for non-blocking sockets in some
cases (f.e. connect()).
With help from Venkat Tekkirala.
Signed-off-by: David S. Miller <davem@davemloft.net>
The tcphdr struct passed to tcp_v4_check is not used, the following
patch removes it from the parameter list.
This adds the netfilter modifications missing in the patch I sent
for rc3-mm1.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With help from Wei Dong <weid@np.css.fujitsu.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netlink users BUG when the allocated skb for an event
notification is undersized. While this is certainly a kernel bug,
its not critical and crashing the kernel is too drastic, especially
when considering that these errors have appeared multiple times in
the past and it BUGs even if no listeners are present.
This patch replaces BUG by WARN_ON and changes the notification
functions to inform potential listeners of undersized allocations
using a unique error code (EMSGSIZE).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a dump_stats callback to enable
printing of basic statistics of prio classes.
(With help of Patrick McHardy).
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (28 commits)
sysfs: Shadow directory support
Driver Core: Increase the default timeout value of the firmware subsystem
Driver core: allow to delay the uevent at device creation time
Driver core: add device_type to struct device
Driver core: add uevent vars for devices of a class
SYSFS: Fix missing include of list.h in sysfs.h
HOWTO: Add a reference to Harbison and Steele
sysfs: error handling in sysfs, fill_read_buffer()
kobject: kobject_put cleanup
sysfs: kobject_put cleanup
sysfs: suppress lockdep warnings
Driver core: fix race in sysfs between sysfs_remove_file() and read()/write()
driver core: Change function call order in device_bind_driver().
driver core: Don't stop probing on ->probe errors.
driver core fixes: device_register() retval check in platform.c
driver core fixes: make_class_name() retval checks
/sys/modules/*/holders
USB: add the sysfs driver name to all modules
SERIO: add the sysfs driver name to all modules
PCI: add the sysfs driver name to all modules
...
This lets the network core have the ability to handle suspend/resume
issues, if it wants to.
Thanks to Frederik Deweerdt <frederik.deweerdt@gmail.com> for the arm
driver fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the entry of Camellia cipher algorithm to ealg_list[].
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Unconfigured bcm43xx device can hit an assert() during wx_get_rate
queries. This is because bcm43xx calls ieee80211softmac_start late
(i.e. during open instead of probe).
bcm43xx_net_open ->
bcm43xx_init_board ->
bcm43xx_select_wireless_core ->
ieee80211softmac_start
Fix is to check that device is running before completing
ieee80211softmac_wx_get_rate.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently only root can trigger a referral automount because only root
can access rpc_pipefs directories. Enabling read access to non-root
should be harmless (they can still not access the pipes themselves)
and will suffice to fix this problem.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The tk_pid field is an unsigned short. The proper print format specifier for
that type is %5u, not %4d.
Also clean up some miscellaneous print formatting nits.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The tk_pid field is an unsigned short. The proper print format specifier for
that type is %5u, not %4d.
Also clean up some miscellaneous print formatting nits.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The error values are already propagated through task->tk_status, and
none of the callers check one without checking the other, so we can
drop the return value.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Fix this by letting NF_CONNTRACK_H323 depend on (IPV6 || IPV6=n).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC net/netfilter/nf_conntrack_netlink.o
net/netfilter/nf_conntrack_netlink.c: In function 'ctnetlink_conntrack_event':
net/netfilter/nf_conntrack_netlink.c:392: error: 'struct nf_conn' has no member named 'mark'
make[3]: *** [net/netfilter/nf_conntrack_netlink.o] Error 1
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The x_tables patch broke target module autoloading in the ipt action
by replacing the ipt_find_target call (which does autoloading) by
xt_find_target (which doesn't do autoloading). Additionally xt_find_target
may return ERR_PTR values in case of an error, which are not handled.
Use xt_request_find_target, which does both autoloading and ERR_PTR
handling properly. Also don't forget to drop the target module reference
again when xt_check_target fails.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP6_NF_IPTABLES=m, CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=y results in a
linker error since ipv6_find_hdr is defined in ip6_tables.c. Fix similar
to Adrian Bunk's H.323 conntrack patch: selecting ip6_tables to be build
as module requires hashlimit to be built as module as well.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing a HEARTBEAT-ACK it's possible that the transport rto
timers will not be updated because a prior T3-RTX processing would
have cleared the rto_pending flag on the transport. However, if
we received a valid HEARTBEAT-ACK, we want to force update the
rto variables, so re-set the rto_pending flag before calling
sctp_transport_update_rto().
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I tested IPv6 redirect function about kernel 2.6.19.1, and found
that the kernel can send redirect packets whose target address is global
address, and the target is not the actual endpoint of communication.
But the criteria conform to RFC2461, the target address defines as
following:
Target Address An IP address that is a better first hop to use for
he ICMP Destination Address. When the target is
the actual endpoint of communication, i.e., the
destination is a neighbor, the Target Address field
MUST contain the same value as the ICMP Destination
Address field. Otherwise the target is a better
first-hop router and the Target Address MUST be the
router's link-local address so that hosts can
uniquely identify routers.
According to this definition, when a router redirect to a host, the
target address either the better first-hop router's link-local address
or the same as the ICMP destination address field. But the function of
ndisc_send_redirect() in net/ipv6/ndisc.c, does not check the target
address correctly.
There is another definition about receive Redirect message in RFC2461:
8.1. Validation of Redirect Messages
A host MUST silently discard any received Redirect message that does
not satisfy all of the following validity checks:
......
- The ICMP Target Address is either a link-local address (when
redirected to a router) or the same as the ICMP Destination
Address (when redirected to the on-link destination).
......
And the receive redirect function of ndisc_redirect_rcv() implemented
this definition, checks the target address correctly.
if (ipv6_addr_equal(dest, target)) {
on_link = 1;
} else if (!(ipv6_addr_type(target) & IPV6_ADDR_LINKLOCAL)) {
ND_PRINTK2(KERN_WARNING
"ICMPv6 Redirect: target address is not link-local.\n");
return;
}
So, I think the send redirect function must check the target address
also.
Signed-off-by: Li Yewang <lyw@nanjing-fnst.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking for an @-sign in skp_epaddr_len, make sure not to
run over the packet boundaries.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to skip over the username in the Contact header, stop at the
end of the line if no @ is found to avoid mangling following headers.
We don't need to worry about continuation lines because we search inside
a SIP URI.
Fixes Netfilter Bugzilla #532.
Signed-off-by: Lars Immisch <lars@ibp.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the packet counter of a connection is zero a division by zero
occurs in div64_64(). Fix that by using zero as average value, which
is correct as long as the packet counter didn't overflow, at which
point we have lost anyway.
Additionally we're probably going to go back to 64 bit counters
in 2.6.21.
Based on patch from Jonas Berlin <xkr47@outerspace.dyndns.org>,
with suggestions from KOVACS Krisztian <hidden@balabit.hu>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove {NFSD,RPC}_PARANOIA as having the defines doesn't really add
anything.
The printks covered by RPC_PARANOIA were triggered by badly formatted
packets and so should be ratelimited.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When main table is just a single leaf this gets printed as belonging to the
local table in /proc/net/fib_trie. A fix is below.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: nf_conntrack_pptp: fix NAT setup of expected GRE connections
[NETFILTER]: nf_nat_pptp: fix expectation removal
[NETFILTER]: nf_nat: fix ICMP translation with statically linked conntrack
[TCP]: Restore SKB socket owner setting in tcp_transmit_skb().
[AF_PACKET]: Check device down state before hard header callbacks.
[DECNET]: Handle a failure in neigh_parms_alloc (take 2)
[BNX2]: Fix 2nd port's MAC address.
[TCP]: Fix sorting of SACK blocks.
[AF_PACKET]: Fix BPF handling.
[IPV4]: Fix the fib trie iterator to work with a single entry routing tables
NFSd assumes that largest number of pages that will be needed for a
request+response is 2+N where N pages is the size of the largest permitted
read/write request. The '2' are 1 for the non-data part of the request, and 1
for the non-data part of the reply.
However, when a read request is not page-aligned, and we choose to use
->sendfile to send it directly from the page cache, we may need N+1 pages to
hold the whole reply. This can overflow and array and cause an Oops.
This patch increases size of the array for holding pages by one and makes sure
that entry is NULL when it is not in use.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to silly typos, if the nfs versions are explicitly set, no NFSACL versions
get enabled.
Also improve an error message that would have made this bug a little easier to
find.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an expected connection arrives, the NAT helper should be called to
set up NAT similar to the master connection. The PPTP conntrack helper
incorrectly checks whether the _expected_ connection has NAT setup before
calling the NAT helper (which is never the case), instead of checkeing
whether the _master_ connection is NATed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing the expectation for the opposite direction, the PPTP NAT
helper initializes the tuple for lookup with the addresses of the
opposite direction, which makes the lookup fail.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When nf_nat/nf_conntrack_ipv4 are linked statically, nf_nat is initialized
before nf_conntrack_ipv4, which makes the nf_ct_l3proto_find_get(AF_INET)
call during nf_nat initialization return the generic l3proto instead of
the AF_INET specific one. This breaks ICMP error translation since the
generic protocol always initializes the IPs in the tuple to 0.
Change the linking order and put nf_conntrack_ipv4 first.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert 931731123a
We can't elide the skb_set_owner_w() here because things like certain
netfilter targets (such as owner MATCH) need a socket to be set on the
SKB for correct operation.
Thanks to Jan Engelhardt and other netfilter list members for
pointing this out.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device is down, invoking the device hard header callbacks
is not legal, so check it early.
Based upon a shaper OOPS report from Frederik Deweerdt.
Signed-off-by: David S. Miller <davem@davemloft.net>
While enhancing the neighbour code to handle multiple network
namespaces I noticed that decnet is assuming neigh_parms_alloc
will allways succeed, which is clearly wrong. So handle the
failure.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Steven Whitehouse <steve@chygwyn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sorting of SACK blocks actually munges them rather than sort,
causing the TCP stack to ignore some SACK information and breaking the
assumption of ordered SACK blocks after sorting.
The sort takes the data from a second buffer which isn't moved causing
subsequent data moves to occur from the wrong location. The fix is to
use a temporary buffer as a normal sort does.
Signed-off-By: Baruch Even <baruch@ev-en.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug introduced by:
commit fda9ef5d67
Author: Dmitry Mishin <dim@openvz.org>
Date: Thu Aug 31 15:28:39 2006 -0700
[NET]: Fix sk->sk_filter field access
sk_run_filter() returns either 0 or an unsigned 32-bit
length which says how much of the packet to retain.
If that 32-bit unsigned integer is larger than the packet,
this is fine we just leave the packet unchanged.
The above commit caused all filter return values which
were negative when interpreted as a signed integer to
indicate a packet drop, which is wrong.
Based upon a report and initial patch by Raivis Bucis.
Signed-off-by: David S. Miller <davem@davemloft.net>
In a kernel with trie routing enabled I had a simple routing setup
with only a single route to the outside world and no default
route. "ip route table list main" showed my the route just fine but
/proc/net/route was an empty file. What was going on?
Thinking it was a bug in something I did and I looked deeper. Eventually
I setup a second route and everything looked correct, huh? Finally I
realized that the it was just the iterator pair in fib_trie_get_first,
fib_trie_get_next just could not handle a routing table with a single entry.
So to save myself and others further confusion, here is a simple fix for
the fib proc iterator so it works even when there is only a single route
in a routing table.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the Oops in http://bugzilla.linux-nfs.org/show_bug.cgi?id=138
We shouldn't be calling rpc_release_task() for tasks that are not active.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I think the return value of rt6_nlmsg_size() should includes the
amount of RTA_METRICS.
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch "Replace CHECKSUM_HW by CHECKSUM_PARTIAL/CHECKSUM_COMPLETE"
changed to unconditional copying of ip_summed field from collapsed
skb. This patch reverts this change.
The majority of substantial work including heavy testing
and diagnosing by: Michael Tokarev <mjt@tls.msk.ru>
Possible reasons pointed by: Herbert Xu and Patrick McHardy.
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I encountered a kernel panic with my test program, which is a very
simple IPv6 client-server program.
The server side sets IPV6_RECVPKTINFO on a listening socket, and the
client side just sends a message to the server. Then the kernel panic
occurs on the server. (If you need the test program, please let me
know. I can provide it.)
This problem happens because a skb is forcibly freed in
tcp_rcv_state_process().
When a socket in listening state(TCP_LISTEN) receives a syn packet,
then tcp_v6_conn_request() will be called from
tcp_rcv_state_process(). If the tcp_v6_conn_request() successfully
returns, the skb would be discarded by __kfree_skb().
However, in case of a listening socket which was already set
IPV6_RECVPKTINFO, an address of the skb will be stored in
treq->pktopts and a ref count of the skb will be incremented in
tcp_v6_conn_request(). But, even if the skb is still in use, the skb
will be freed. Then someone still using the freed skb will cause the
kernel panic.
I suggest to use kfree_skb() instead of __kfree_skb().
Signed-off-by: Masayuki Nakagawa <nakagawa.msy@ncos.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent hashing introduced an off-by-one bug in policy list insertion.
Instead of adding after the last entry with a lesser or equal priority,
we're adding after the successor of that entry.
This patch fixes this and also adds a warning if we detect a duplicate
entry in the policy list. This should never happen due to this if clause.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
__x25_find_socket does a sock_hold.
This adds a missing sock_put in x25_receive_data.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when association enters SHUTDOWN state,the
implementation will SACK any DATA first and then transmit
the SHUTDOWN chunk. This is against the order required by
2960bis spec. SHUTDOWN must always be first, followed by
SACK. This change forces this order and also enables bundling.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the chunk as Out-of-the-Blue if we don't have
an endpoint. Otherwise discard it as before.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify init_tag and a_rwnd mandatory parameters in INIT and
INIT-ACK chunks.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_process_missing_param() needs to use the SCTP_ERROR_MISS_PARAM
error cause value.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Join all-node multicast group after assignment of dev->ip6_ptr
because it must be assigned when ipv6_dev_mc_inc() is called.
This fixes Bug#7817, reported by <gernoth@informatik.uni-erlangen.de>.
Closes: 7817
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When old flow cache entries that are not at the head of their chain
trigger a transient security error they get unlinked along with all
the entries preceding them in the chain. The preceding entries are
not freed correctly.
This patch fixes this by simply leaving the entry around. It's based
on a suggestion by Venkat Yekkirala.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change my email address to reflect OSDL merger.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
[ The irony. Somebody still has his sign-off message hardcoded
in a script or his brainstem ;^]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PSM values below 0x1001 of L2CAP are reserved for well known
services. Restrict the possibility to bind them to privileged
users.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
inetdev_init out label moved after RCU assignment
(final suggestion by Herbert Xu)
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A quick patch to change the inet_sock->is_icsk assignment to better fit with
existing kernel coding style.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The subh->err_hdr should point to the error header, not the data.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading the NAT module, existing connection tracking entries don't
have room for NAT information allocated and packets are dropped, causing
hanging connections. They really should be entered into the NAT table
as NULL mappings, but the current allocation scheme doesn't allow this.
For now simply accept those packets to avoid the hanging connections.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IPv6 connection tracking splits up a defragmented packet into
its original fragments, the packets are taken from a list and are
passed to the network stack with skb->next still set. This causes
dev_hard_start_xmit to treat them as GSO fragments, resulting in
a use after free when connection tracking handles the next fragment.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the ftp stalls present in the current kernels.
All credit goes to Komuro <komurojun-mbn@nifty.com> for tracking
this down. The patch is untested but it looks *cough* obviously
correct.
Signed-off-by: Craig Schlenter <craig@codefountain.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
->helper is uninitialized in the expectation registered by the netbios_ns
helper and it later copied to the expected connection, which causes invalid
memory dereferences when trying to call the helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current netlbl_cipsov4_add_common() function has two problems which are
fixed with this patch. The first is an off-by-one bug where it is possibile to
overflow the doi_def->tags[] array. The second is a bug where the same
doi_def->tags[] array was not always fully initialized, which caused sporadic
failures.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
In the case the device registration for a new Bluetooth low-level
connection fails there is no need to unregister it when the temporary
data structure has been removed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When calling send() with a zero length parameter on a RFCOMM socket
it returns a positive value. In this rare case the variable err is
used uninitialized and unfortunately its value is returned.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the DLC device is no longer attached to the TTY device, then return
errors or default values for various callbacks of the TTY layer.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With malformed packets it might be possible to overwrite internal
CMTP and CAPI data structures. This patch adds additional length
checks to prevent these kinds of remote attacks.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Trivial. Newlines missing on the SOCK_DEBUG's for X.25 facility
negotiation.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inet_create() and inet6_create() functions incorrectly set the
inet_sock->is_icsk field. Both functions assume that the is_icsk field is
large enough to hold at least a INET_PROTOSW_ICSK value when it is actually
only a single bit. This patch corrects the assignment by doing a boolean
comparison whose result will safely fit into a single bit field.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is important that we only assign dev->ip{,6}_ptr
only after all portions of the inet{,6} are setup.
Otherwise we can receive packets before the multicast
spinlocks et al. are initialized.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot compute the gap until we know we have a 'struct ebt_entry' and
not 'struct ebt_entries'. Failure to check can cause crash.
Tested-by: Santiago Garcia Mantinan <manty@manty.net>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the return value of nfct_nat() in device_cmp(), we might very well
have non NAT conntrack entries as well (Netfilter bugzilla #528).
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets generated by the REJECT target in the output chain have a local
destination address and a foreign source address. Make sure not to use
the foreign source address for the output route lookup.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Used by compat code offsets of entries should be 'unsigned int' as entries
array size has this dimension.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a proper prototype for x25_init_timers() in
include/net/x25.h
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes redundant argument check for module_put().
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
All ->doit handlers want a struct rtattr **, so pass down the right
type.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a suggestion from Christoph Hellwig.
This fixes various races in module load/unload handling
too.
Signed-off-by: David S. Miller <davem@davemloft.net>
Installing an IPsec SA using old algorithm names (.compat) does not work
if the algorithm is not already loaded. When not using the PF_KEY
interface, algorithms are not preloaded in xfrm_probe_algs() and
installing a IPsec SA fails.
Signed-off-by: Martin Willi <martin@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When this code was converted to use sk_for_each() the
logic for the "best hash chain length" code was reversed,
breaking everything.
The original code was of the form:
size = 0;
do {
if (++size >= best_size_so_far)
goto next;
} while ((sk = sk->next) != NULL);
best_size_so_far = size;
best = result;
next:;
and this got converted into:
sk_for_each(sk2, node, head)
if (++size < best_size_so_far) {
best_size_so_far = size;
best = result;
}
Which does something very very different from the original.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the following needlessly global functions static:
- ipv6.c: sctp_inet6addr_event()
- protocol.c: sctp_inetaddr_event()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ivan Skytte Jorgensen <isj-sctp@i1.dk>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back when the original NetLabel patches were being changed to use Netlink
attributes correctly some code was accidentially dropped which set all of the
undefined CIPSOv4 level and category mappings to a sentinel value. The result
is the mappings data in the kernel contains bogus mappings which always map to
zero. This patch restores the old/correct behavior by initializing the mapping
data to the correct sentinel value.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
There are a couple of cases where the user input for a CIPSOv4 DOI add
operation was not being done soon enough; the result was unexpected behavior
which was resulting in oops/panics/lockups on some platforms. This patch moves
the existing input validation code earlier in the code path to protect against
bogus user input.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Return error and prevent from loading module when gss_mech_register()
failed.
Cc: Andy Adamson <andros@citi.umich.edu>
Cc: J. Bruce Fields <bfields@citi.umich.edu>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ieee80211softmac_wx_get_genie locks the associnfo mutex at
function exit. This patch fixes it. The patch is against Linus'
tree (commit af1713e0).
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The signature of work functions changed recently from a context
pointer to the work structure pointer. This caused a problem in
the ieee80211softmac code, because the ieee80211softmac_assox_work
function has been called directly with a parameter explicitly
casted to (void*). This compiled correctly but resulted in a
softlock, because mutex_lock was called with the wrong memory
address. The patch fixes the problem. Another issue was a wrong
call of the schedule_work function. Softmac works again and this
fixes the problem I mentioned earlier in the zd1211rw rx tasklet
patch. The patch is against Linus' tree (commit af1713e0).
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the redirect packet of the router if the jiffies wraparound.
Signed-off-by: Li Yewang <lyw@nanjing-fnst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message logged in tcp_v4_inbound_md5_hash when the hash was expected
but not found was reversed.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
md5sig_info.alloced4 must be set to zero when freeing keys4, otherwise
it will not be alloc'd again when another key is added to the same
socket by tcp_v4_md5_do_add.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the menu dependencies in net/ipv6/netfilter/Kconfig
guard the entries in that file from the Kconfig GUI, this does
not prevent them from being selected still via "make oldconfig"
when IPV6 etc. is disabled.
So add explicit dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
rose_add_loopback_neigh uses kmalloc and the callers were ignoring the
error value. Rewrite to let the caller deal with the allocation. This
allows the use of static allocation of kmalloc use entirely.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ax25_linkfail_register uses kmalloc and the callers were ignoring the
error value. Rewrite to let the caller deal with the allocation. This
allows the use of static allocation of kmalloc use entirely.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ax25_listen_register to return something that's a sane error code,
then all callers to use it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace ax25_protocol_register by ax25_register_pid which assumes the
caller has done the memory allocation. This allows replacing the
kmalloc allocations entirely by static allocations.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent fix 0506d4068b made obvious that
error values were not being propagated through the AX.25 stack. To help
with that this patch marks all kmalloc users in the AX.25, NETROM and
ROSE stacks as __must_check.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the deferred hooks and all related code as scheduled in
feature-removal-schedule.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make fib6_node 'subtree' depend on IPV6_SUBTREES.
Signed-off-by: Kim Nordlund <kim.nordlund@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ivan Skytte Jorgensen <isj-sctp@i1.dk>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in SCTP, we maintain a local address list by rebuilding the whole
list from the device list whenever we get a address add/delete event.
This patch fixes it by only adding/deleting the address for which we
receive the event.
Also removed the sctp_local_addr_lock() which is no longer needed as we
now use list_for_each_safe() to traverse this list. This fixes the bugs
in sctp_copy_laddrs_xxx() routines where we do copy_to_user() while
holding this lock.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should call tcp_free_md5sig_pool() not __tcp_free_md5sig_pool()
so that it does proper refcounting.
Signed-off-by: David S. Miller <davem@davemloft.net>
> Relevant standard (RFC 3493) notes:
>
> The IPV6_UNICAST_HOPS option may be used with getsockopt() to
> determine the hop limit value that the system will use for subsequent
> unicast packets sent via that socket.
>
> I don't reckon -1 could be the hop limit value.
-1 means un-initialized.
> IMHO, the value from
> case 1 (if socket is connected to some destination), otherwise case 2
> (if bound to a scope interface) or ultimately the default hop limit
> ought to be returned instead, as it will be most often correct, while
> the current behavior is always wrong, unless setsockopt() has been used
> first. I don't if some people may think doing a route lookup in
> getsockopt might be overly expensive, but at least the two other cases
> should be ok, particularly the last one.
The following patch seems to work for me, but this code has behaved this
way for a while, so don't know if it will break any existing apps.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a recent patch we introduced invalid return codes which will result in the
opposite of what is intended (i.e. send more packets in face of peculiar
network conditions).
This fixes it by returning ~0 which means not calculated as per
dccp_li_hist_calc_i_mean.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
If we come to node we'd already marked as seen and it's not a part of path
(i.e. we don't have a loop right there), we already know that it isn't a
part of any loop, so we don't need to revisit it.
That speeds the things up if some chain is refered to from several places
and kills O(exp(table size)) worst-case behaviour (without sleeping,
at that, so if you manage to self-LART that way, you are SOL for a long
time)...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matches and targets verification is duplicated in normal and compat processing
ways. This patch refactors code in order to remove this.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CLUSTERIP, CONNMARK, CONNSECMARK, and connbytes need ip_conntrack or
layer 3 protocol module of nf_conntrack.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To do that, this makes nf_ct_l3proto_try_module_{get,put} compatible
functions. As a result we can remove '#ifdef' surrounds and direct call of
need_conntrack().
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_NAT depends on NF_CONNTRACK_IPV4, not NF_CONNTRACK.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building with INET=n results in
WARNING: "ip_route_output_key" [net/netfilter/nf_conntrack_h323.ko] undefined!
The entire code in net/netfilter is only used for IPv4/IPv6 currently, so
let it depend on INET.
Noticed by Toralf Förster <toralf.foerster@gmx.de>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no point deferring something just to immediately fail the deferral,
especially now that we can do something more useful in the failure case by
returning an error.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To avoid tying up server threads when nfsd makes an upcall (to mountd, to get
export options, to idmapd, for nfsv4 name<->id mapping, etc.), we temporarily
"drop" the request and save enough information so that we can revisit it
later.
Certain failures during the deferral process can cause us to really drop the
request and never revisit it.
This is often less than ideal, and is unacceptable in the NFSv4 case--rfc 3530
forbids the server from dropping a request without also closing the
connection.
As a first step, we modify the deferral code to return -ETIMEDOUT (which is
translated to nfserr_jukebox in the v3 and v4 cases, and remains a drop in the
v2 case).
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The memory leak here is embarassingly obvious.
This fixes a problem that causes the kernel to leak a small amount of memory
every time it receives a integrity-protected request.
Thanks to Aim Le Rouzic for the bug report.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All kcalloc() calls of the form "kcalloc(1,...)" are converted to the
equivalent kzalloc() calls, and a few kcalloc() calls with the incorrect
ordering of the first two arguments are fixed.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
Fix inotify maintainers entry
Fix typo in new debug options.
Jon needs a new shift key.
fs: Convert kmalloc() + memset() to kzalloc() in fs/.
configfs.h: Remove dead macro definitions.
kconfig: Standardize "depends" -> "depends on" in Kconfig files
e100: replace kmalloc with kcalloc
um: replace kmalloc+memset with kzalloc
fix typo in net/ipv4/ip_fragment.c
include/linux/compiler.h: reject gcc 3 < gcc 3.2
Kconfig: fix spelling error in config KALLSYMS help text
Remove duplicate "have to" in comment
Fix small typo in drivers/serial/icom.c
Use consistent casing in help message
EXT{2,3,4}_FS: remove outdated part of the help text
current -git doesnt boot on my laptop due to netpoll not unlocking the
tx lock in the else branch.
booted this up on my laptop with lockdep enabled and there are no
locking complaints and it works fine.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During boot we get:
netconsole: device eth0 not up yet, forcing it
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
WARNING (!__warned) at kernel/softirq.c:137 local_bh_enable()
Call Trace:
[<ffffffff80235baf>] local_bh_enable+0x41/0xa3
[<ffffffff8045ab8e>] netpoll_send_skb+0x116/0x144
[<ffffffff8045b1ee>] netpoll_send_udp+0x263/0x271
[<ffffffff803d41ec>] write_msg+0x42/0x5e
[<ffffffff80230c9b>] __call_console_drivers+0x5f/0x70
[<ffffffff80230d19>] _call_console_drivers+0x6d/0x71
[<ffffffff802313f0>] release_console_sem+0x148/0x1ec
[<ffffffff802316ce>] register_console+0x1b1/0x1ba
[<ffffffff803d4178>] init_netconsole+0x54/0x68
[<ffffffff802071ae>] init+0x152/0x308
[<ffffffff804dac8b>] _spin_unlock_irq+0x14/0x30
[<ffffffff8022c15e>] schedule_tail+0x43/0x9f
[<ffffffff8020a758>] child_rip+0xa/0x12
Herbert sayeth:
Normally networking isn't invoked with interrupts turned off, but I
suppose we don't have a choice here. This is unique being a place where you
can get called with BH on, off, or IRQs off.
Given that this is only used for printk, the easiest solution is probably
just to disable local IRQs instead of BH.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dean Manners notices that when an IPVS synchonisation daemons are
started the system load slowly climbs up to 1. This seems to be related
to the call to ssleep(1) (aka msleep(1000) in the main loop. Replacing
this with a call to msleep_interruptable() seems to make the problem go
away. Though I'm not sure that it is correct.
This is the second edition of this patch, which replaces ssleep()
in the main loop for both the master and backup threads, as well
as some thread synchronisation code. The latter is just for thorougness
as it shouldn't be causing any problems.
Signed-Off-By: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix foobar in 15b1c0e822 and
e8cc49bb0f patch series.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
That accumulated over the last months hackaton, shame on me for not
using git-apply whitespace helping hand, will do that from now on.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Spotted by David Miller when compiling on sparc64, I reproduced it here on
parisc64, that are the only platforms to define __kernel_suseconds_t as an
'int', all the others, x86_64 and x86 included typedef it as a 'long', but from
the definition of suseconds_t it should just be an 'int' on platforms where it
is >= 32bits, it would not require all the castings from suseconds_t to (int)
when printking variables of this type, that are not needed on parisc64 and
sparc64.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This fixes conversion errors which arose by not properly type-casting
from u32 to __u64. Fixed by explicitly casting each type which is not
__u64, or by performing operation after assignment.
The patch further adds missing debug information to track the current
value of X_recv.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
No code change at all.
This reorders the source file to follow the same order as the corresponding
header file.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
No code change at all.
To make the header file easier to read, the following ordering is established
among the declarations:
* hist_new
* hist_delete
* hist_entry_new
* hist_head
* hist_find_entry
* hist_add_entry
* hist_entry_delete
* hist_purge
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch does not alter any algorithm, just the debug message format:
* s#%s, sk=%p#%s(%p)#g
* when a statename is present, it now uses %s(%p, state=%s)
* when only function entry is debugged, it adds an `- entry'
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This migrates all packet history operations into the routine
ccid3_hc_tx_packet_sent, thereby removing synchronization problems
that occur when, as before, the operations are spread over multiple
routines.
The following minor simplifications are also applied:
* several simplifications now follow from this change - several tests
are now no longer required
* removal of one unnecessary variable (dp)
Justification:
Currently packet history operations span two different routines,
one of which is likely to pass through several iterations of sleeping
and awakening.
The first routine, ccid3_hc_tx_send_packet, allocates an entry and
sets a few fields. The remaining fields are filled in when the second
routine (which is not within a sleeping context), ccid3_hc_tx_packet_sent,
is called. This has several strong drawbacks:
* it is not necessary to split history operations - all fields can be
filled in by the second routine
* the first routine is called multiple times, until a packet can be sent,
and sleeps meanwhile - this causes a lot of difficulties with regard to
keeping the list consistent
* since both routines do not have a producer-consumer like synchronization,
it is very difficult to maintain data across calls to these routines
* the fact that the routines are called in different contexts (sleeping, not
sleeping) adds further problems
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This removes the `dccphtx_ccval' field since it is nowhere used in the code and
in fact not necessary for the accounting.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This puts the window counter computation [RFC 4342, 8.1] into a separate
function which is called whenever a new packet is ready for immediate
transmission in ccid3_hc_tx_send_packet.
Justification:
The window counter update was previously computed after the packet was sent. This has
two drawbacks, both fixed by this patch:
1) re-compute another timestamp almost directly after the packet was sent (expensive),
2) the CCVal for the window counter is needed at the instant the packet is sent.
Further details:
The initialisation of the window counter is left in the state NO_SENT, as before.
The algorithm will do nothing if either RTT is initialised to 0 (which is ok) or if
the RTT value remains below 4 microseconds (which is almost pathological).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
CCID3 performance depends much on the accuracy of RTT samples. If RTT
samples grow too large, performance can be catastrophically poor.
To limit the amount of possible damage in such cases, the patch
* introduces an upper limit which identifies a maximum `sane' RTT value;
* uses a macro to enforce this upper limit.
Using a macro was given preference, since it is necessary to identify the
calling function in the warning message. Since exceeding this threshold
identifies a critical condition, DCCP_CRIT is used and not DCCP_WARN.
Many thanks to Ian McDonald for collaboration on this issue.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
In both the sender and the receiver it is possible that the stored
RTT value is accessed before an actual RTT estimate has been computed.
This patch
* initialises the sender RTT to 0
- the sender always accesses the RTT in ccid3_hc_tx_packet_sent
- the RTT is further needed for the window counter algorithm
* replaces the receiver initialisation of 5msec with 0
- which has the same effect and removes an `XXX'
- the RTT value is needed in ccid3_hc_rx_packet_recv as rtt_prev
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The function ccid3_hc_tx_insert_options only does a redundant no-op,
as the operation
DCCP_SKB_CB(skb)->dccpd_ccval = hctx->ccid3hctx_last_win_count;
is already performed _unconditionally_ in ccid3_hc_tx_send_packet.
Since there is further no current need for this function, it is removed
entirely. Since furthermore, there is actually no present need for the
entire interface function ccid_hc_tx_insert_options, it was decided to
remove it also, to clean up the interface.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This adds a (debug) warning message which is triggered whenever a packet is
discarded due to send failure.
It also adds a conditional, so that an interruption during dccp_wait_for_ccid
is not treated as a `BUG': the rationale is that interruptions are external,
whereas bug warnings are concerned with the internals.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This is an optimisation to reduce CPU load. The received feedback is now
only directed to the active CCID component, without requiring processing
also by the inactive one.
As a consequence, a similar test in ccid3.c is now redundant and is
also removed.
Justification:
Currently DCCP works as a unidirectional service, i.e. a listening server
is not at the same time a connecting client.
As far as I can see, several modifications are necessary until that
becomes possible.
At the present time, received feedback is both fed to the rx/tx CCID
modules. In unidirectional service, only one of these is active at any
one time.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
In migrating towards using the newer functions scaled_div/scaled_div32
for TFRC computations mapped from floating-point onto integer arithmetic,
this completes the last stage of modifications.
In particular, the overflow case for computing X_calc is circumvented by
* breaking the computation into two stages
* the first stage, res = (s*1E6)/R, cannot overflow due to use of u64
* in the second stage, res = (res*1E6)/f, overflow on u32 is avoided due
to (i) returning UINT_MAX in this case (which is logically appropriate)
and (ii) issuing a warning message into the system log (since very likely
there is a problem somewhere else with the parameters)
Lastly, all such scaling operations are now exported into tfrc.h, since
actually this form of scaled computation is specific to TFRC and not to CCID3.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Problem:
Most target types in the CCID3 code are u32, so subtle conversion errors
can occur if signed time calculations yield negative results: the original
values are lost in the conversion to unsigned, calculation errors go undetected.
This patch therefore
* sets all critical time types from unsigned to suseconds_t
* avoids comparison between signed/unsigned via type-casting
* provides ample warning messages in case time calculations are negative
These warning messages can be removed at a later stage when the code
has undergone more testing.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This simplifies the calculation of a value p for a given fval when the
first loss interval is computed (RFC 3448, 6.3.1). It makes use of the
two new functions scaled_div/scaled_div32 to provide overflow protection.
Additionally, protection against divide-by-zero is extended - in this
case the function will return the maximally possible value of p=100%.
Background:
The maximum fval, f(100%), is approximately 244, i.e. the scaled value of fval
should never exceed 244E6, which fits easily into u32. The problem is the scaling
by 10^6, since additionally R(TT) is in microseconds.
This is resolved by breaking the division into two stages: the first stage
computes fval=(s*10^6)/R, stores that into u64; the second stage computes
fval = (fval*10^6)/X_recv and complains if overflow is reached for u32.
This case is safe since the TFRC reverse-lookup routine then returns p=100%.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This replaces the remaining uses of usecs_div with scaled_div32, which
internally uses 64bit division and produces a warning on overflow.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch
* resolves a bug where packets smaller than 32/64 bytes resulted in sending rates of 0
* supports all sending rates from 1/64 bytes/second up to 4Gbyte/second
* simplifies the present overflow problems in calculations
Current sending rate X and the cached value X_recv of the receiver-estimated
sending rate are both scaled by 64 (2^6) in order to
* cope with low sending rates (minimally 1 byte/second)
* allow upgrading to use a packets-per-second implementation of CCID 3
* avoid calculation errors due to integer arithmetic cut-off
The patch implements a revised strategy from
http://www.mail-archive.com/dccp@vger.kernel.org/msg01040.html
The only difference with regard to that strategy is that t_ipi is already
used in the calculation of the nofeedback timeout, which saves one division.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This fixes
1) a bug in the recomputation of the sending rate by the nofeedback
timer when no feedback at all has so far been sent by the receiver:
min_t was used instead of max_t, which is wrong (cf. RFC 3448, p. 10);
2) an error in the computation of larger initial windows: instead of
min(... max()) (cf. RFC 4342, 5.), the code had used max(... max()).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This performs two optimisations for the recomputation of the sending rate.
1) Currently the target sending rate X_calc is recalculated whenever
a) the nofeedback timer expires, or
b) a feedback packet is received.
In the (a) case, recomputing X_calc is redundant, since
* the parameters p and RTT do not change in between the
reception of feedback packets;
* the parameter X_recv is either modified from received
feedback or via the nofeedback timer;
* a test (`p == 0') in the nofeedback timer avoids using
a stale/undefined value of X_calc if p was previously 0.
2) The nofeedback timer now only recomputes a timestamp when p == 0.
This is according to step (4) of [RFC 3448, 4.3] and avoids
unnecessarily determining a timestamp.
A debug statement about not updating X is also removed - it helps very
little in debugging and just clutters the logs.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch follows a suggestion by Ian McDonald and ensures that in
the current code the value of p can not exceed 100%. Such a value is
illegal and would consequently cause a bug condition in tfrc_calc_x().
The receiver case is also tested, and a warning message is added.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
It simplifies waiting for the CCID module to signal that a packet
is ready to be sent. Other simplifications flow on from this such as
removing constants.
As a result of this EAGAIN is not returned any more by dccp_wait_for_ccid
(which would otherwise lead to unnecessarily discarding the packet in
dccp_write_xmit).
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Fix ieee80211-softmac compile problem where it's using schedule_work() on a
delayed_work struct.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- turn intermediate classes into leaves again when their
last child is deleted (struct htb_class changed)
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
- deactivating of active classes when q.qlen drops to zero
(cbq_drop)
- a redundant instruction removed from cbq_deactivate_class
PS: probably htb_deactivate in htb_delete and
cbq_deactivate_class in cbq_delete are also
redundant now.
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in 2.4 arp requests that were recevied by netpoll were processed
in netconsole_receive_skb, where they were responded to using the src
mac of the request sender. In the 2.6 kernel arp_reply is responsible
for this function, but instead of using the src mac address of the
incomming request, the stored mac address that was registered for the
netconsole application is used. While this is usually ok, it can lead
to failures in netpoll in some situations (specifically situations
where a network may have two gateways, as arp requests from one may be
responded to using the mac address of the other). This patch reverts
the behavior to what we had in 2.4, in which all arp requests are sent
back using the src address of the request sender.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the callsign but not the SSID part of an AX.25 address is ASCII
based but Linux by initializes the SSID which should be just a 4-bit
number from ASCII anyway.
Fix that and convert the code to use a shared constant for both default
addresses. While at it, use the same style for null_ax25_address also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hard header cache is in the main output path, so using
seqlock instead of reader/writer lock should reduce overhead.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the grungy swap all the occurrences in the right places patch that
goes with the updates. At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs
If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.
If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)
Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia
[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the core of the switch to the new framework. I've split it from the
driver patches which are mostly search/replace and would encourage people to
give this one a good hard stare.
The references to BOTHER and ISHIFT are the termios values that must be
defined by a platform once it wants to turn on "new style" ioctl support. The
code patches here ensure that providing
1. The termios overlays the ktermios in memory
2. The only new kernel only fields are c_ispeed/c_ospeed (or none)
the existing behaviour is retained. This is true for the patches at this
point in time.
Future patches will define BOTHER, ISHIFT and enable newer termios structures
for each architecture, and once they are all done some of the ifdefs also
vanish.
[akpm@osdl.org: warning fix]
[akpm@osdl.org: IRDA fix]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We currently insert socket dentries into the global dentry hashtable. This
is suboptimal because there is currently no way these entries can be used
for a lookup(). (/proc/xxx/fd/xxx uses a different mechanism). Inserting
them in dentry hashtable slows dcache lookups.
To let __dpath() still work correctly (ie not adding a " (deleted)") after
dentry name, we do :
- Right after d_alloc(), pretend they are hashed by clearing the
DCACHE_UNHASHED bit.
- Call d_instantiate() instead of d_add() : dentry is not inserted in
hash table.
__dpath() & friends work as intended during dentry lifetime.
- At dismantle time, once dput() must clear the dentry, setting again
DCACHE_UNHASHED bit inside the custom d_delete() function provided by
socket code, so that dput() can just kill_it.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was lots of #ifdef noise in the kernel due to hotcpu_notifier(fn,
prio) not correctly marking 'fn' as used in the !HOTPLUG_CPU case, and thus
generating compiler warnings of unused symbols, hence forcing people to add
#ifdefs.
the compiler can skip truly unused functions just fine:
text data bss dec hex filename
1624412 728710 3674856 6027978 5bfaca vmlinux.before
1624412 728710 3674856 6027978 5bfaca vmlinux.after
[akpm@osdl.org: topology.c fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Name some of the remaning 'old_style_spin_init' locks
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stick NFS sockets in their own class to avoid some lockdep warnings. NFS
sockets are never exposed to user-space, and will hence not trigger certain
code paths that would otherwise pose deadlock scenarios.
[akpm@osdl.org: cleanups]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Steven Dickson <SteveD@redhat.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Acked-by: Neil Brown <neilb@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
[ Fixed patch corruption by quilt, pointed out by Peter Zijlstra ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch (as824b) makes percpu_free() ignore NULL arguments, as one would
expect for a deallocation routine. (Note that free_percpu is #defined as
percpu_free in include/linux/percpu.h.) A few callers are updated to remove
now-unneeded tests for NULL. A few other callers already seem to assume
that passing a NULL pointer to percpu_free() is okay!
The patch also removes an unnecessary NULL check in percpu_depopulate().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Node-aware allocation of skbs for the receive path.
Details:
- __alloc_skb gets a new node argument and cals the node-aware
slab functions with it.
- netdev_alloc_skb passed the node number it gets from dev_to_node
to it, everyone else passes -1 (any node)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix non-ANSI function declaration:
net/netfilter/nf_conntrack_core.c:1096:25: warning: non-ANSI function declaration of function 'nf_conntrack_flush'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per Ralf Baechle's observations, the schedule_work() call
should give enough of a memory barrier, so the explicit one
here is totally unnecessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe all the below memory barriers only matter on SMP so
therefore the smp_* variant of the barrier should be used.
I'm wondering if the barrier in net/ipv4/inet_timewait_sock.c should be
dropped entirely. schedule_work's implementation currently implies a
memory barrier and I think sane semantics of schedule_work() should imply
a memory barrier, as needed so the caller shouldn't have to worry.
It's not quite obvious why the barrier in net/packet/af_packet.c is
needed; maybe it should be implied through flush_dcache_page?
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We grab a reference to the route's inetpeer entry but
forget to release it in xfrm4_dst_destroy().
Bug discovered by Kazunori MIYAZAWA <kazunori@miyazawa.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disables auditing in ipsec when CONFIG_AUDITSYSCALL is
disabled in the kernel.
Also includes a bug fix for xfrm_state.c as a result of
original ipsec audit patch.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An audit message occurs when an ipsec SA
or ipsec policy is created/deleted.
Signed-off-by: Joy Latten <latten@austin.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must reserve SAR + MAX_HEADER bytes for IrLMP to fit in.
Patch from Jeet Chaudhuri <jeetlinux@yahoo.co.in>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
