Provide the needed kernel support for distinguishing readahead
from regular read requests when tracing block devices.
Signed-off-by: Nathan Scott <nathans@sgi.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Reimplement controller-wide PM. ata_host_set_suspend/resume() are
defined to suspend and resume a host_set. While suspended, EHs for
all ports in the host_set are pegged using ATA_FLAG_SUSPENDED and
frozen.
Because SCSI device hotplug is done asynchronously against the rest of
libata EH and the same mutex is used when adding new device, suspend
cannot wait for hotplug to complete. So, if SCSI device hotplug is in
progress, suspend fails with -EBUSY.
In most cases, host_set resume is followed by device resume. As each
resume operation requires a reset, a single host_set-wide resume
operation may result in multiple resets. To avoid this, resume waits
upto 1 second giving PM to request resume for devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement per-dev PM. The original implementation directly put the
device into suspended mode and didn't synchronize w/ EH operations
including hotplug. This patch reimplements ata_scsi_device_suspend()
and ata_scsi_device_resume() such that they request EH to perform the
respective operations. Both functions synchronize with hotplug such
that it doesn't operate on detached devices.
Suspend waits for completion but resume just issues request and
returns. This allows parallel wake up of devices and thus speeds up
system resume.
Due to sdev detach synchronization, it's not feasible to separate out
EH requesting from sdev handling; thus, ata_device_suspend/resume()
are removed and everything is implemented in the respective
libata-scsi functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement two PM per-dev EH actions - ATA_EH_SUSPEND and
ATA_EH_RESUME. Each action puts the target device into suspended mode
and resumes from it respectively.
Once a device is put to suspended mode, no EH operations other than
RESUME is allowed on the device. The device will stay suspended till
it gets resumed and thus reset and revalidated. To implement this, a
new device state helper - ata_dev_ready() - is implemented and used in
EH action implementations to make them operate only on attached &
running devices.
If all possible devices on a port are suspended, reset is skipped too.
This prevents spurious events including hotplug events from disrupting
suspended devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out __ata_ehi_hotplugged() from ata_ehi_hotplugged(). The
underscored version doesn't set AC_ERR_ATA_BUS. This will be used for
resume which is a hotplug event but not an ATA bus error.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ATA_EHI_NO_AUTOPSY and QUIET. These used to be implied by
ATA_PFLAG_LOADING, but new power management and PMP support need to
use these separately. e.g. Suspend/resume operations shouldn't print
full EH messages and resume shouldn't be recorded as an error.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The names of predefined debounce timing parameters didn't exactly
match their usages. Rename to more generic names and implement param
selection helper sata_ehc_deb_timing() which uses EHI_HOTPLUGGED to
select params.
Combined with the previous EHI_RESUME_LINK differentiation, this makes
parameter selection accurate. e.g. user scan resumes link but normal
deb param is used instead of hotplug param.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ATA_EHI_RESUME_LINK, which indicates that the link needs to
be resumed. This used to be implied by ATA_EHI_HOTPLUGGED. However,
hotplug isn't the only event which requires link resume and separating
this out allows other places to request link resume. This
differentiation also allows better debounce timing selection.
This patch converts user scan to use ATA_EHI_RESUME_LINK.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ap->flags is way too clamped. Separate out core dynamic flags to
ap->pflags. ATA_FLAG_DISABLED is a dynamic flag but left alone as
it's referenced by a lot of LLDs and it's gonna be removed once all
LLDs are converted to new EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change posix_lock_file_conf(), and flock_lock_file() so that if called
with an F_UNLCK argument, and the FL_EXISTS flag they will indicate
whether or not any locks were actually freed by returning 0 or -ENOENT.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
Move workqueue exports to where the functions are defined.
[CPUFREQ] Misc cleanups in ondemand.
[CPUFREQ] Make ondemand sampling per CPU and remove the mutex usage in sampling path.
[CPUFREQ] Add queue_delayed_work_on() interface for workqueues.
[CPUFREQ] Remove slowdown from ondemand sampling path.
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Ensure 8250_pci quirks are not marked __devinit
[SERIAL] Convert fifosize to an unsigned int
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
[Bluetooth] Add RFCOMM role switch support
[Bluetooth] Allow disabling of credit based flow control
[Bluetooth] Small cleanup of the L2CAP source code
[Bluetooth] Use real devices for host controllers
[Bluetooth] Add platform device for virtual and serial devices
[Bluetooth] Add automatic sniff mode support
[Bluetooth] Correct SCO buffer size on request
[Bluetooth] Add suspend/resume support to the HCI USB driver
[Bluetooth] Use raw mode for the Frontline sniffer device
[BRIDGE]: br_dump_ifinfo index fix
[ATM]: add+use poison defines
[NET]: add+use poison defines
[IOAT]: fix kernel-doc in source files
[IOAT]: fix header file kernel-doc
[TG3]: Add ipv6 TSO feature
[IPV6]: Fix ipv6 GSO payload length
[TIPC] Fixed sk_buff panic caused by tipc_link_bundle_buf (REVISED)
[NET]: Verify gso_type too in gso_segment
[IPVS]: Add sysctl documentation
[ROSE]: Try all routes when establishing a ROSE connections.
...
Fix kernel-doc problems in include/linux/dmaengine.h:
- add some fields/parameters
- expand some descriptions
- fix typos
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
convert:
- runqueue_t to 'struct rq'
- prio_array_t to 'struct prio_array'
- migration_req_t to 'struct migration_req'
I was the one who added these but they are both against the kernel coding
style and also were used inconsistently at places. So just get rid of them at
once, now that we are flushing the scheduler patch-queue anyway.
Conversion was mostly scripted, the result was reviewed and all secondary
whitespace and style impact (if any) was fixed up by hand.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cleanup: remove task_t and convert all the uses to struct task_struct. I
introduced it for the scheduler anno and it was a mistake.
Conversion was mostly scripted, the result was reviewed and all
secondary whitespace and style impact (if any) was fixed up by hand.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Teach special (recursive) locking code to the lock validator.
Effects on non-lockdep kernels:
- the introduction of the following function variants:
extern struct block_device *open_partition_by_devnum(dev_t, unsigned);
extern int blkdev_put_partition(struct block_device *);
static int
blkdev_get_whole(struct block_device *bdev, mode_t mode, unsigned flags);
which on non-lockdep are the same as open_by_devnum(), blkdev_put()
and blkdev_get().
- a subclass parameter to do_open(). [unused on non-lockdep]
- a subclass parameter to __blkdev_put(), which is a new internal
function for the main blkdev_put*() functions. [parameter unused
on non-lockdep kernels, except for two sanity check WARN_ON()s]
these functions carry no semantical difference - they only express
object dependencies towards the lockdep subsystem.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The s_umount rwsem needs to be classified as per-superblock since it's
perfectly legit to keep multiple of those recursively in the VFS locking
rules.
Has no effect on non-lockdep kernels.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Teach special (per-filesystem) locking code to the lock validator.
Minimal effect on non-lockdep kernels: one extra parameter to alloc_super().
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make use of local_irq_enable_in_hardirq() API to annotate places that enable
hardirqs in hardirq context.
Has no effect on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Teach special (recursive) locking code to the lock validator. Has no effect
on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Teach special (multi-initialized) locking code to the lock validator. Has no
effect on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create one lock class for all waitqueue locks in the kernel. Has no effect on
non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Teach special (recursive) locking code to the lock validator. Has no effect
on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Teach special (recursive) locking code to the lock validator. Has no effect
on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Teach special (recursive) locking code to the lock validator. Has no effect
on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the lock validator framework to prove mutex locking correctness.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the lock validator framework to prove spinlock and rwlock locking
correctness.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the lock validator framework to prove rwsem locking correctness.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do 'make oldconfig' and accept all the defaults for new config options -
reboot into the kernel and if everything goes well it should boot up fine and
you should have /proc/lockdep and /proc/lockdep_stats files.
Typically if the lock validator finds some problem it will print out
voluminous debug output that begins with "BUG: ..." and which syslog output
can be used by kernel developers to figure out the precise locking scenario.
What does the lock validator do? It "observes" and maps all locking rules as
they occur dynamically (as triggered by the kernel's natural use of spinlocks,
rwlocks, mutexes and rwsems). Whenever the lock validator subsystem detects a
new locking scenario, it validates this new rule against the existing set of
rules. If this new rule is consistent with the existing set of rules then the
new rule is added transparently and the kernel continues as normal. If the
new rule could create a deadlock scenario then this condition is printed out.
When determining validity of locking, all possible "deadlock scenarios" are
considered: assuming arbitrary number of CPUs, arbitrary irq context and task
context constellations, running arbitrary combinations of all the existing
locking scenarios. In a typical system this means millions of separate
scenarios. This is why we call it a "locking correctness" validator - for all
rules that are observed the lock validator proves it with mathematical
certainty that a deadlock could not occur (assuming that the lock validator
implementation itself is correct and its internal data structures are not
corrupted by some other kernel subsystem). [see more details and conditionals
of this statement in include/linux/lockdep.h and
Documentation/lockdep-design.txt]
Furthermore, this "all possible scenarios" property of the validator also
enables the finding of complex, highly unlikely multi-CPU multi-context races
via single single-context rules, increasing the likelyhood of finding bugs
drastically. In practical terms: the lock validator already found a bug in
the upstream kernel that could only occur on systems with 3 or more CPUs, and
which needed 3 very unlikely code sequences to occur at once on the 3 CPUs.
That bug was found and reported on a single-CPU system (!). So in essence a
race will be found "piecemail-wise", triggering all the necessary components
for the race, without having to reproduce the race scenario itself! In its
short existence the lock validator found and reported many bugs before they
actually caused a real deadlock.
To further increase the efficiency of the validator, the mapping is not per
"lock instance", but per "lock-class". For example, all struct inode objects
in the kernel have inode->inotify_mutex. If there are 10,000 inodes cached,
then there are 10,000 lock objects. But ->inotify_mutex is a single "lock
type", and all locking activities that occur against ->inotify_mutex are
"unified" into this single lock-class. The advantage of the lock-class
approach is that all historical ->inotify_mutex uses are mapped into a single
(and as narrow as possible) set of locking rules - regardless of how many
different tasks or inode structures it took to build this set of rules. The
set of rules persist during the lifetime of the kernel.
To see the rough magnitude of checking that the lock validator does, here's a
portion of /proc/lockdep_stats, fresh after bootup:
lock-classes: 694 [max: 2048]
direct dependencies: 1598 [max: 8192]
indirect dependencies: 17896
all direct dependencies: 16206
dependency chains: 1910 [max: 8192]
in-hardirq chains: 17
in-softirq chains: 105
in-process chains: 1065
stack-trace entries: 38761 [max: 131072]
combined max dependencies: 2033928
hardirq-safe locks: 24
hardirq-unsafe locks: 176
softirq-safe locks: 53
softirq-unsafe locks: 137
irq-safe locks: 59
irq-unsafe locks: 176
The lock validator has observed 1598 actual single-thread locking patterns,
and has validated all possible 2033928 distinct locking scenarios.
More details about the design of the lock validator can be found in
Documentation/lockdep-design.txt, which can also found at:
http://redhat.com/~mingo/lockdep-patches/lockdep-design.txt
[bunk@stusta.de: cleanups]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Accurate hard-IRQ-flags and softirq-flags state tracing.
This allows us to attach extra functionality to IRQ flags on/off
events (such as trace-on/off).
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Framework to generate and save stacktraces quickly, without printing anything
to the console.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Locking init improvement:
- introduce and use __SPIN_LOCK_UNLOCKED for array initializations,
to pass in the name string of locks, used by debugging
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Generic lock debugging:
- generalized lock debugging framework. For example, a bug in one lock
subsystem turns off debugging in all lock subsystems.
- got rid of the caller address passing (__IP__/__IP_DECL__/etc.) from
the mutex/rtmutex debugging code: it caused way too much prototype
hackery, and lockdep will give the same information anyway.
- ability to do silent tests
- check lock freeing in vfree too.
- more finegrained debugging options, to allow distributions to
turn off more expensive debugging features.
There's no separate 'held mutexes' list anymore - but there's a 'held locks'
stack within lockdep, which unifies deadlock detection across all lock
classes. (this is independent of the lockdep validation stuff - lockdep first
checks whether we are holding a lock already)
Here are the current debugging options:
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_LOCK_ALLOC=y
which do:
config DEBUG_MUTEXES
bool "Mutex debugging, basic checks"
config DEBUG_LOCK_ALLOC
bool "Detect incorrect freeing of live mutexes"
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
lockdep needs to have the waitqueue lock initialized for on-stack waitqueues
implicitly initialized by DECLARE_COMPLETION(). Introduce the API.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce local_irq_enable_in_hardirq() API. It is currently aliased to
local_irq_enable(), hence has no functional effects.
This API will be used by lockdep, but even without lockdep this will better
document places in the kernel where a hardirq context enables hardirqs.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
lockdep wants to use the disable_irq()/enable_irq() prototypes before they are
provied by the platform's asm/irq.h. So move them out of the
CONFIG_GENERIC_HARDIRQS define - all architectures have a common prototype for
this anyway.
Add special lockdep variants of irq line disabling/enabling.
These should be used for locking constructs that know that a particular irq
context which is disabled, and which is the only irq-context user of a lock,
that it's safe to take the lock in the irq-disabled section without disabling
hardirqs.
[akpm@osdl.org: build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide a common print_ip_sym() function that prints the passed instruction
pointer as well as the symbol belonging to it. Avoids adding a bunch of
#ifdef CONFIG_64BIT in order to get the printk format right on 32/64 bit
platforms.
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add is_module_address() method - to be used by lockdep.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out that it is advantageous to leave a small portion of unmapped file
backed pages if all of a zone's pages (or almost all pages) are allocated and
so the page allocator has to go off-node.
This allows recently used file I/O buffers to stay on the node and
reduces the times that zone reclaim is invoked if file I/O occurs
when we run out of memory in a zone.
The problem is that zone reclaim runs too frequently when the page cache is
used for file I/O (read write and therefore unmapped pages!) alone and we have
almost all pages of the zone allocated. Zone reclaim may remove 32 unmapped
pages. File I/O will use these pages for the next read/write requests and the
unmapped pages increase. After the zone has filled up again zone reclaim will
remove it again after only 32 pages. This cycle is too inefficient and there
are potentially too many zone reclaim cycles.
With the 1% boundary we may still remove all unmapped pages for file I/O in
zone reclaim pass. However. it will take a large number of read and writes
to get back to 1% again where we trigger zone reclaim again.
The zone reclaim 2.6.16/17 does not show this behavior because we have a 30
second timeout.
[akpm@osdl.org: rename the /proc file and the variable]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ACPI supplies a "shareable" indication, but PNPACPI ignores it. If a PNP
device uses a shared interrupt, request_irq() fails because the PNP driver
can't tell whether to supply SA_SHIRQ.
This patch allows PNP drivers to test
(pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE)
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Matthieu Castet <castet.matthieu@free.fr>
Cc: Li Shaohua <shaohua.li@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Have a special version of print_symbol() for s390 which clears the most
significant bit of addr before calling __print_symbol(). This seems to be
better than checking/changing each place in the kernel that saves an
instruction pointer.
Without this the output would look like:
hardirqs last enabled at (30907): [<80018c6a>] 0x80018c6a
hardirqs last disabled at (30908): [<8001e48c>] 0x8001e48c
softirqs last enabled at (30904): [<8001dc96>] 0x8001dc96
softirqs last disabled at (30897): [<8001dc50>] 0x8001dc50
instead of this:
hardirqs last enabled at (19421): [<80018c72>] cpu_idle+0x176/0x1c4
hardirqs last disabled at (19422): [<8001e494>] io_no_vtime+0xa/0x1a
softirqs last enabled at (19418): [<8001dc9e>] do_softirq+0xa6/0xe8
softirqs last disabled at (19411): [<8001dc58>] do_softirq+0x60/0xe8
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
include/linux/version.h contained both actual KERNEL version
and UTS_RELEASE that contains a subset from git SHA1 for when
kernel was compiled as part of a git repository.
This had the unfortunate side-effect that all files including version.h
would be recompiled when some git changes was made due to changes SHA1.
Split it out so we keep independent parts in separate files.
Also update checkversion.pl script to no longer check for UTS_RELEASE.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The irqflags consolidation converted SA_PERCPU_IRQ to IRQF_PERCPU but
did not define the new constant.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus: "The hacks in kernel/irq/handle.c are really horrid. REALLY
horrid."
They are indeed. Move the dyntick quirks to ARM where they belong.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent interrupt rework introduced bit value conflicts with sparc.
Instead of introducing new architecture flags mess, move the interrupt SA_
flags out of the signal namespace and replace them by interrupt related flags.
This allows to remove the obsolete SA_INTERRUPT flag and clean up the bit
field values.
This patch:
Move the interrupt related SA_ flags out of linux/signal.h and rename them to
IRQF_ . This moves the interrupt related flags out of the signal namespace
and allows to remove the architecture dependencies.
SA_INTERRUPT is not needed by userspace and glibc so it can be removed safely.
The existing SA_ constants are kept for easy transition and will be
removed after a 6 month grace period.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Greg KH <greg@kroah.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Ben Collins <bcollins@debian.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Jens Axboe <axboe@suse.de>
Cc: Chris Zankel <chris@zankel.net>
Cc: Andi Kleen <ak@muc.de>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: David Howells <dhowells@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some UARTs have more than 255 bytes of FIFO, which can't be
represented by an unsigned char. Change the kernel's internal
structure to be an unsigned int, but still export an unsigned char
via the TIOCGSERIAL ioctl. If the TIOCSSERIAL ioctl provides a
fifo size of 0, assume this means "don't change" otherwise we'll
corrupt the larger fifo sizes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add ids for SDHCI controllers so that they can be identified for quirks.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
ARM has a couple of really dumb interrupt controllers.
Implement a generic one and fixup the ARM migration. ARM reused
the no_irq_chip for this purpose, but this does not work out
for platforms which are not converted to the new interrupt
type handling model.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Always use do {} while (0). Failing to do so can cause subtle compile
failures or bugs.
Cc: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Raise the maximum error number in IS_ERR_VALUE to 4095.
o Make that number available as a new constant MAX_ERRNO.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes buggy behaviour of UFS
in such kind of scenario:
open(, O_TRUNC...)
ftruncate(, 1024)
ftruncate(, 0)
Such a scenario causes ufs_panic and remount read-only. This happen
because of according to specification UFS should always allocate block for
last byte, and many parts of our implementation rely on this, but
`ufs_truncate' doesn't care about this.
To make possible return error code and to know about old size, this patch
removes `truncate' from ufs inode_operations and uses `setattr' method to
call ufs_truncate.
Signed-off-by: Evgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow to tie upper bits of syscall bitmap in audit rules to kernel-defined
sets of syscalls. Infrastructure, a couple of classes (with 32bit counterparts
for biarch targets) and actual tie-in on i386, amd64 and ia64.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch renames some audit constant definitions and adds
additional definitions used by the following patch. The renaming
avoids ambiguity with respect to the new definitions.
Signed-off-by: Darrel Goeddel <dgoeddel@trustedcs.com>
include/linux/audit.h | 15 ++++++++----
kernel/auditfilter.c | 50 ++++++++++++++++++++---------------------
kernel/auditsc.c | 10 ++++----
security/selinux/ss/services.c | 32 +++++++++++++-------------
4 files changed, 56 insertions(+), 51 deletions(-)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add support for a rule key, which can be used to tie audit records to audit
rules. This is useful when a watched file is accessed through a link or
symlink, as well as for general audit log analysis.
Because this patch uses a string key instead of an integer key, there is a bit
of extra overhead to do the kstrdup() when a rule fires. However, we're also
allocating memory for the audit record buffer, so it's probably not that
significant. I went ahead with a string key because it seems more
user-friendly.
Note that the user must ensure that filterkeys are unique. The kernel only
checks for duplicate rules.
Signed-off-by: Amy Griffis <amy.griffis@hpd.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPV6]: Added GSO support for TCPv6
[NET]: Generalise TSO-specific bits from skb_setup_caps
[IPV6]: Added GSO support for TCPv6
[IPV6]: Remove redundant length check on input
[NETFILTER]: SCTP conntrack: fix crash triggered by packet without chunks
[TG3]: Update version and reldate
[TG3]: Add TSO workaround using GSO
[TG3]: Turn on hw fix for ASF problems
[TG3]: Add rx BD workaround
[TG3]: Add tg3_netif_stop() in vlan functions
[TCP]: Reset gso_segs if packet is dodgy
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6/:
[PATCH] pcmcia: fix deadlock in pcmcia_parse_events
[PATCH] com20020_cs: more device support
[PATCH] au1xxx: pcmcia: fix __init called from non-init
[PATCH] kill open-coded offsetof in cm4000_cs.c ZERO_DEV()
[PATCH] pcmcia: convert pcmcia_cs to kthread
[PATCH] pcmcia: fix kernel-doc function name
[PATCH] pcmcia: hostap_cs.c - 0xc00f,0x0000 conflicts with pcnet_cs
[PATCH] pcmcia: at91_cf suspend/resume/wakeup
[PATCH] pcmcia: Make ide_cs work with the memory space of CF-Cards if IO space is not available
[PATCH] pcmcia: TI PCIxx12 CardBus controller support
[PATCH] pcmcia: warn if driver requests exclusive, but gets a shared IRQ
[PATCH] pcmcia: expose tool in pcmcia/Documentation/pcmcia/
[PATCH] pcmcia: another ID for serial_cs.c
[PATCH] yenta: fix hidden PCI bus numbers
[PATCH] yenta: do power-up only after socket is configured
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (25 commits)
ACPI: Kconfig: ACPI_SRAT depends on ACPI
ACPI: drivers/acpi/scan.c: make acpi_bus_type static
ACPI: fixup memhotplug debug message
ACPI: ACPICA 20060623
ACPI: C-States: only demote on current bus mastering activity
ACPI: C-States: bm_activity improvements
ACPI: C-States: accounting of sleep states
ACPI: additional blacklist entry for ThinkPad R40e
ACPI: restore comment justifying 'extra' P_LVLx access
ACPI: fix battery on HP NX6125
ACPIPHP: prevent duplicate slot numbers when no _SUN
ACPI: static-ize handle_hotplug_event_func()
ACPIPHP: use ACPI dock driver
ACPI: dock driver
KEVENT: add new uevent for dock
ACPI: asus_acpi_init: propagate correct return value
[ACPI] Print error message if remove/install notify handler fails
ACPI: delete tracing macros from drivers/acpi/*.c
ACPI: HW P-state coordination support
ACPI: un-export ACPI_ERROR() -- use printk(KERN_ERR...)
...
This patch adds GSO support for IPv6 and TCPv6. This is based on a patch
by Ananda Raju <Ananda.Raju@neterion.com>. His original description is:
This patch enables TSO over IPv6. Currently Linux network stacks
restricts TSO over IPv6 by clearing of the NETIF_F_TSO bit from
"dev->features". This patch will remove this restriction.
This patch will introduce a new flag NETIF_F_TSO6 which will be used
to check whether device supports TSO over IPv6. If device support TSO
over IPv6 then we don't clear of NETIF_F_TSO and which will make the
TCP layer to create TSO packets. Any device supporting TSO over IPv6
will set NETIF_F_TSO6 flag in "dev->features" along with NETIF_F_TSO.
In case when user disables TSO using ethtool, NETIF_F_TSO will get
cleared from "dev->features". So even if we have NETIF_F_TSO6 we don't
get TSO packets created by TCP layer.
SKB_GSO_TCPV4 renamed to SKB_GSO_TCP to make it generic GSO packet.
SKB_GSO_UDPV4 renamed to SKB_GSO_UDP as UFO is not a IPv4 feature.
UFO is supported over IPv6 also
The following table shows there is significant improvement in
throughput with normal frames and CPU usage for both normal and jumbo.
--------------------------------------------------
| | 1500 | 9600 |
| ------------------|-------------------|
| | thru CPU | thru CPU |
--------------------------------------------------
| TSO OFF | 2.00 5.5% id | 5.66 20.0% id |
--------------------------------------------------
| TSO ON | 2.63 78.0 id | 5.67 39.0% id |
--------------------------------------------------
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch generalises the TSO-specific bits from sk_setup_caps by adding
the sk_gso_type member to struct sock. This makes sk_setup_caps generic
so that it can be used by TCPv6 or UFO.
The only catch is that whoever uses this must provide a GSO implementation
for their protocol which I think is a fair deal :) For now UFO continues to
live without a GSO implementation which is OK since it doesn't use the sock
caps field at the moment.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch below adds support for the TI PCIxx12 CardBus controllers.
This seems to be sufficient to detect the cardbus bridge on an HP nc6320
and works with an orinoco wifi card.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add a rq_sendfile_ok flag to svc_rqst which will be cleared in the privacy
case so that the wrapping code will get copies of the read data instead of
real page cache pages. This makes life simpler when we encrypt the response.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add __acquire annotations to rcu_read_lock and rcu_read_lock_bh, and add
__release annotations to rcu_read_unlock and rcu_read_unlock_bh. This
allows sparse to detect improperly paired calls to these functions.
Signed-off-by: Josh Triplett <josh@freedesktop.org>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This corrects the comments describing the 'enabled' and 'pending' flags in
struct rtc_wkalrm of include/linux/rtc.h.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Presently, smp_processor_id() isn't necessarily set up until setup_arch().
But it's used in boot_cpu_init() and printk() and perhaps in other places,
prior to setup_arch() being called.
So provide a new smp_setup_processor_id() which is called before anything
else, wire it up for Voyager (which boots on a CPU other than #0, and broke).
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new security hook definition for the sys_ioprio_get operation. At
present, the SELinux hook function implementation for this hook is
identical to the getscheduler implementation but a separate hook is
introduced to allow this check to be specialized in the future if
necessary.
This patch also creates a helper function get_task_ioprio which handles the
access check in addition to retrieving the ioprio value for the task.
Signed-off-by: David Quigley <dpquigl@tycho.nsa.gov>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a call to the extended security_task_kill hook introduced by
the prior patch to the kill_proc_info_as_uid function so that these signals
can be properly mediated by security modules. It also updates the existing
hook call in check_kill_permission.
Signed-off-by: David Quigley <dpquigl@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch extends the security_task_kill hook to handle signals sent by AIO
completion. In this case, the secid of the task responsible for the signal
needs to be obtained and saved earlier, so a security_task_getsecid() hook is
added, and then this saved value is passed subsequently to the extended
task_kill hook for use in checking.
Signed-off-by: David Quigley <dpquigl@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The remaining counters in page_state after the zoned VM counter patches
have been applied are all just for show in /proc/vmstat. They have no
essential function for the VM.
We use a simple increment of per cpu variables. In order to avoid the most
severe races we disable preempt. Preempt does not prevent the race between
an increment and an interrupt handler incrementing the same statistics
counter. However, that race is exceedingly rare, we may only loose one
increment or so and there is no requirement (at least not in kernel) that
the vm event counters have to be accurate.
In the non preempt case this results in a simple increment for each
counter. For many architectures this will be reduced by the compiler to a
single instruction. This single instruction is atomic for i386 and x86_64.
And therefore even the rare race condition in an interrupt is avoided for
both architectures in most cases.
The patchset also adds an off switch for embedded systems that allows a
building of linux kernels without these counters.
The implementation of these counters is through inline code that hopefully
results in only a single instruction increment instruction being emitted
(i386, x86_64) or in the increment being hidden though instruction
concurrency (EPIC architectures such as ia64 can get that done).
Benefits:
- VM event counter operations usually reduce to a single inline instruction
on i386 and x86_64.
- No interrupt disable, only preempt disable for the preempt case.
Preempt disable can also be avoided by moving the counter into a spinlock.
- Handling is similar to zoned VM counters.
- Simple and easily extendable.
- Can be omitted to reduce memory use for embedded use.
References:
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=113512330605497&w=2
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=114988082814934&w=2
local_t http://marc.theaimsgroup.com/?l=linux-kernel&m=114991748606690&w=2
V2 http://marc.theaimsgroup.com/?t=115014808400007&r=1&w=2
V3 http://marc.theaimsgroup.com/?l=linux-kernel&m=115024767022346&w=2
V4 http://marc.theaimsgroup.com/?l=linux-kernel&m=115047968808926&w=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The numa statistics are really event counters. But they are per node and
so we have had special treatment for these counters through additional
fields on the pcp structure. We can now use the per zone nature of the
zoned VM counters to realize these.
This will shrink the size of the pcp structure on NUMA systems. We will
have some room to add additional per zone counters that will all still fit
in the same cacheline.
Bits Prior pcp size Size after patch We can add
------------------------------------------------------------------
64 128 bytes (16 words) 80 bytes (10 words) 48
32 76 bytes (19 words) 56 bytes (14 words) 8 (64 byte cacheline)
72 (128 byte)
Remove the special statistics for numa and replace them with zoned vm
counters. This has the side effect that global sums of these events now
show up in /proc/vmstat.
Also take the opportunity to move the zone_statistics() function from
page_alloc.c into vmstat.c.
Discussions:
V2 http://marc.theaimsgroup.com/?t=115048227000002&r=1&w=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No callers.
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_bounce to a per zone counter
nr_bounce is only used for proc output. So it could be left as an event
counter. However, the event counters may not be accurate and nr_bounce is
categorizing types of pages in a zone. So we really need this to also be a
per zone counter.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_unstable to a per zone counter
We need to do some special modifications to the nfs code since there are
multiple cases of disposition and we need to have a page ref for proper
accounting.
This converts the last critical page state of the VM and therefore we need to
remove several functions that were depending on GET_PAGE_STATE_LAST in order
to make the kernel compile again. We are only left with event type counters
in page state.
[akpm@osdl.org: bugfixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_writeback to per zone counter.
This removes the last page_state counter from arch/i386/mm/pgtable.c so we
drop the page_state from there.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes nr_dirty a per zone counter. Looping over all processors is
avoided during writeback state determination.
The counter aggregation for nr_dirty had to be undone in the NFS layer since
we summed up the page counts from multiple zones. Someone more familiar with
NFS should probably review what I have done.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_page_table_pages to a per zone counter
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Allows reclaim to access counter without looping over processor counts.
- Allows accurate statistics on how many pages are used in a zone by
the slab. This may become useful to balance slab allocations over
various zones.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The zone_reclaim_interval was necessary because we were not able to determine
how many unmapped pages exist in a zone. Therefore we had to scan in
intervals to figure out if any pages were unmapped.
With the zoned counters and NR_ANON_PAGES we now know the number of pagecache
pages and the number of mapped pages in a zone. So we can simply skip the
reclaim if there is an insufficient number of unmapped pages. We use
SWAP_CLUSTER_MAX as the boundary.
Drop all support for /proc/sys/vm/zone_reclaim_interval.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current NR_FILE_MAPPED is used by zone reclaim and the dirty load
calculation as the number of mapped pagecache pages. However, that is not
true. NR_FILE_MAPPED includes the mapped anonymous pages. This patch
separates those and therefore allows an accurate tracking of the anonymous
pages per zone.
It then becomes possible to determine the number of unmapped pages per zone
and we can avoid scanning for unmapped pages if there are none.
Also it may now be possible to determine the mapped/unmapped ratio in
get_dirty_limit. Isnt the number of anonymous pages irrelevant in that
calculation?
Note that this will change the meaning of the number of mapped pages reported
in /proc/vmstat /proc/meminfo and in the per node statistics. This may affect
user space tools that monitor these counters! NR_FILE_MAPPED works like
NR_FILE_DIRTY. It is only valid for pagecache pages.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently a single atomic variable is used to establish the size of the page
cache in the whole machine. The zoned VM counters have the same method of
implementation as the nr_pagecache code but also allow the determination of
the pagecache size per zone.
Remove the special implementation for nr_pagecache and make it a zoned counter
named NR_FILE_PAGES.
Updates of the page cache counters are always performed with interrupts off.
We can therefore use the __ variant here.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
nr_mapped is important because it allows a determination of how many pages of
a zone are not mapped, which would allow a more efficient means of determining
when we need to reclaim memory in a zone.
We take the nr_mapped field out of the page state structure and define a new
per zone counter named NR_FILE_MAPPED (the anonymous pages will be split off
from NR_MAPPED in the next patch).
We replace the use of nr_mapped in various kernel locations. This avoids the
looping over all processors in try_to_free_pages(), writeback, reclaim (swap +
zone reclaim).
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Per zone counter infrastructure
The counters that we currently have for the VM are split per processor. The
processor however has not much to do with the zone these pages belong to. We
cannot tell f.e. how many ZONE_DMA pages are dirty.
So we are blind to potentially inbalances in the usage of memory in various
zones. F.e. in a NUMA system we cannot tell how many pages are dirty on a
particular node. If we knew then we could put measures into the VM to balance
the use of memory between different zones and different nodes in a NUMA
system. For example it would be possible to limit the dirty pages per node so
that fast local memory is kept available even if a process is dirtying huge
amounts of pages.
Another example is zone reclaim. We do not know how many unmapped pages exist
per zone. So we just have to try to reclaim. If it is not working then we
pause and try again later. It would be better if we knew when it makes sense
to reclaim unmapped pages from a zone. This patchset allows the determination
of the number of unmapped pages per zone. We can remove the zone reclaim
interval with the counters introduced here.
Futhermore the ability to have various usage statistics available will allow
the development of new NUMA balancing algorithms that may be able to improve
the decision making in the scheduler of when to move a process to another node
and hopefully will also enable automatic page migration through a user space
program that can analyse the memory load distribution and then rebalance
memory use in order to increase performance.
The counter framework here implements differential counters for each processor
in struct zone. The differential counters are consolidated when a threshold
is exceeded (like done in the current implementation for nr_pageache), when
slab reaping occurs or when a consolidation function is called.
Consolidation uses atomic operations and accumulates counters per zone in the
zone structure and also globally in the vm_stat array. VM functions can
access the counts by simply indexing a global or zone specific array.
The arrangement of counters in an array also simplifies processing when output
has to be generated for /proc/*.
Counters can be updated by calling inc/dec_zone_page_state or
_inc/dec_zone_page_state analogous to *_page_state. The second group of
functions can be called if it is known that interrupts are disabled.
Special optimized increment and decrement functions are provided. These can
avoid certain checks and use increment or decrement instructions that an
architecture may provide.
We also add a new CONFIG_DMA_IS_NORMAL that signifies that an architecture can
do DMA to all memory and therefore ZONE_NORMAL will not be populated. This is
only currently set for IA64 SGI SN2 and currently only affects
node_page_state(). In the best case node_page_state can be reduced to
retrieving a single counter for the one zone on the node.
[akpm@osdl.org: cleanups]
[akpm@osdl.org: export vm_stat[] for filesystems]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NOTE: ZVC are *not* the lightweight event counters. ZVCs are reliable whereas
event counters do not need to be.
Zone based VM statistics are necessary to be able to determine what the state
of memory in one zone is. In a NUMA system this can be helpful for local
reclaim and other memory optimizations that may be able to shift VM load in
order to get more balanced memory use.
It is also useful to know how the computing load affects the memory
allocations on various zones. This patchset allows the retrieval of that data
from userspace.
The patchset introduces a framework for counters that is a cross between the
existing page_stats --which are simply global counters split per cpu-- and the
approach of deferred incremental updates implemented for nr_pagecache.
Small per cpu 8 bit counters are added to struct zone. If the counter exceeds
certain thresholds then the counters are accumulated in an array of
atomic_long in the zone and in a global array that sums up all zone values.
The small 8 bit counters are next to the per cpu page pointers and so they
will be in high in the cpu cache when pages are allocated and freed.
Access to VM counter information for a zone and for the whole machine is then
possible by simply indexing an array (Thanks to Nick Piggin for pointing out
that approach). The access to the total number of pages of various types does
no longer require the summing up of all per cpu counters.
Benefits of this patchset right now:
- Ability for UP and SMP configuration to determine how memory
is balanced between the DMA, NORMAL and HIGHMEM zones.
- loops over all processors are avoided in writeback and
reclaim paths. We can avoid caching the writeback information
because the needed information is directly accessible.
- Special handling for nr_pagecache removed.
- zone_reclaim_interval vanishes since VM stats can now determine
when it is worth to do local reclaim.
- Fast inline per node page state determination.
- Accurate counters in /sys/devices/system/node/node*/meminfo. Current
counters are counting simply which processor allocated a page somewhere
and guestimate based on that. So the counters were not useful to show
the actual distribution of page use on a specific zone.
- The swap_prefetch patch requires per node statistics in order to
figure out when processors of a node can prefetch. This patch provides
some of the needed numbers.
- Detailed VM counters available in more /proc and /sys status files.
References to earlier discussions:
V1 http://marc.theaimsgroup.com/?l=linux-kernel&m=113511649910826&w=2
V2 http://marc.theaimsgroup.com/?l=linux-kernel&m=114980851924230&w=2
V3 http://marc.theaimsgroup.com/?l=linux-kernel&m=115014697910351&w=2
V4 http://marc.theaimsgroup.com/?l=linux-kernel&m=115024767318740&w=2
Performance tests with AIM7 did not show any regressions. Seems to be a tad
faster even. Tested on ia64/NUMA. Builds fine on i386, SMP / UP. Includes
fixes for s390/arm/uml arch code.
This patch:
Move counter code from page_alloc.c/page-flags.h to vmstat.c/h.
Create vmstat.c/vmstat.h by separating the counter code and the proc
functions.
Move the vm_stat_text array before zoneinfo_show.
[akpm@osdl.org: s390 build fix]
[akpm@osdl.org: HOTPLUG_CPU build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
skb_release_data() no longer has any users in other files.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current TSO implementation, NETIF_F_TSO and ECN cannot be
turned on together in a TCP connection. The problem is that most
hardware that supports TSO does not handle CWR correctly if it is set
in the TSO packet. Correct handling requires CWR to be set in the
first packet only if it is set in the TSO header.
This patch adds the ability to turn on NETIF_F_TSO and ECN using
GSO if necessary to handle TSO packets with CWR set. Hardware
that handles CWR correctly can turn on NETIF_F_TSO_ECN in the dev->
features flag.
All TSO packets with CWR set will have the SKB_GSO_TCPV4_ECN set. If
the output device does not have the NETIF_F_TSO_ECN feature set, GSO
will split the packet up correctly with CWR only set in the first
segment.
With help from Herbert Xu <herbert@gondor.apana.org.au>.
Since ECN can always be enabled with TSO, the SOCK_NO_LARGESEND sock
flag is completely removed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements an API whereby an application can determine the
label of its peer's Unix datagram sockets via the auxiliary data mechanism of
recvmsg.
Patch purpose:
This patch enables a security-aware application to retrieve the
security context of the peer of a Unix datagram socket. The application
can then use this security context to determine the security context for
processing on behalf of the peer who sent the packet.
Patch design and implementation:
The design and implementation is very similar to the UDP case for INET
sockets. Basically we build upon the existing Unix domain socket API for
retrieving user credentials. Linux offers the API for obtaining user
credentials via ancillary messages (i.e., out of band/control messages
that are bundled together with a normal message). To retrieve the security
context, the application first indicates to the kernel such desire by
setting the SO_PASSSEC option via getsockopt. Then the application
retrieves the security context using the auxiliary data mechanism.
An example server application for Unix datagram socket should look like this:
toggle = 1;
toggle_len = sizeof(toggle);
setsockopt(sockfd, SOL_SOCKET, SO_PASSSEC, &toggle, &toggle_len);
recvmsg(sockfd, &msg_hdr, 0);
if (msg_hdr.msg_controllen > sizeof(struct cmsghdr)) {
cmsg_hdr = CMSG_FIRSTHDR(&msg_hdr);
if (cmsg_hdr->cmsg_len <= CMSG_LEN(sizeof(scontext)) &&
cmsg_hdr->cmsg_level == SOL_SOCKET &&
cmsg_hdr->cmsg_type == SCM_SECURITY) {
memcpy(&scontext, CMSG_DATA(cmsg_hdr), sizeof(scontext));
}
}
sock_setsockopt is enhanced with a new socket option SOCK_PASSSEC to allow
a server socket to receive security context of the peer.
Testing:
We have tested the patch by setting up Unix datagram client and server
applications. We verified that the server can retrieve the security context
using the auxiliary data mechanism of recvmsg.
Signed-off-by: Catherine Zhang <cxzhang@watson.ibm.com>
Acked-by: Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test in skb_gso_ok is backwards. Noticed by Michael Chan
<mchan@broadcom.com>.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch encapsulates the usage of eff_cap (in netlink_skb_params) within
the security framework by extending security_netlink_recv to include a required
capability parameter and converting all direct usage of eff_caps outside
of the lsm modules to use the interface. It also updates the SELinux
implementation of the security_netlink_send and security_netlink_recv
hooks to take advantage of the sid in the netlink_skb_params struct.
This also enables SELinux to perform auditing of netlink capability checks.
Please apply, for 2.6.18 if possible.
Signed-off-by: Darrel Goeddel <dgoeddel@trustedcs.com>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When GSO packets come from an untrusted source (e.g., a Xen guest domain),
we need to verify the header integrity before passing it to the hardware.
Since the first step in GSO is to verify the header, we can reuse that
code by adding a new bit to gso_type: SKB_GSO_DODGY. Packets with this
bit set can only be fed directly to devices with the corresponding bit
NETIF_F_GSO_ROBUST. If the device doesn't have that bit, then the skb
is fed to the GSO engine which will allow the packet to be sent to the
hardware if it passes the header check.
This patch changes the sg flag to a full features flag. The same method
can be used to implement TSO ECN support. We simply have to mark packets
with CWR set with SKB_GSO_ECN so that only hardware with a corresponding
NETIF_F_TSO_ECN can accept them. The GSO engine can either fully segment
the packet, or segment the first MTU and pass the rest to the hardware for
further segmentation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (33 commits)
[MIPS] Add missing backslashes to macro definitions.
[MIPS] Death list of board support to be removed after 2.6.18.
[MIPS] Remove BSD and Sys V compat data types.
[MIPS] ioc3.h: Uses u8, so include <linux/types.h>.
[MIPS] 74K: Assume it will also have an AR bit in config7
[MIPS] Treat CPUs with AR bit as physically indexed.
[MIPS] Oprofile: Support VSMP on 34K.
[MIPS] MIPS32/MIPS64 S-cache fix and cleanup
[MIPS] excite: PCI makefile needs to use += if it wants a chance to work.
[MIPS] excite: plat_setup -> plat_mem_setup.
[MIPS] au1xxx: export dbdma functions
[MIPS] au1xxx: dbdma, no sleeping under spin_lock
[MIPS] au1xxx: fix PSC_SMBTXRX_RSR.
[MIPS] Early printk for IP27.
[MIPS] Fix handling of 0 length I & D caches.
[MIPS] Typo fixes.
[MIPS] MIPS32/MIPS64 secondary cache management
[MIPS] Fix FIXADDR_TOP for TX39/TX49.
[MIPS] Remove first timer interrupt setup in wrppmc_timer_setup()
[MIPS] Fix configuration of R2 CPU features and multithreading.
...
They have been obsoleted by the ELF header EI_CLASS and EI_DATA fields
in combination with e_flags. Afaics EM_MIPS_RS3_LE and EM_MIPS_RS4_BE
never had any practical relevance. Binutils will not produce such
binaries and the kernel will not accept them as MIPS binaries.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
Clean up the fastack concept by turning it into fasteoi and introducing the
->eoi() method for chips.
This also allows the cleanup of an i386 EOI quirk - now the quirk is
cleanly separated from the pure ACK implementation.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a #define for the mask of the part of IRQ_TYPE that represents the
trigger type. I use that in my in-progress work as I've standardized the
way the irq description in the firmware device-tree get translated to linux
useable things by using those constants. Having this mask to isolate the
"trigger type" part of the flags is useful in a few places.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms to set the irq-wake (power-management) properties of an IRQ.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms to use the irq-chip and irq-flow abstractions: allow setting
of the chip, the type and provide highlevel handlers for common irq-flows.
[rostedt@goodmis.org: misroute-irq: Don't call desc->chip->end because of edge interrupts]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a fixed up and cleaned up replacement for genirq-msi-fixes.patch,
which should solve the i386 4KSTACKS problem. I also added Ben's idea of
pushing the __do_IRQ() check into generic_handle_irq().
I booted this with MSI enabled, but i only have MSI devices, not MSI-X
devices. I'd still expect MSI-X to work now.
irqchip migration helper: call __do_IRQ() if a descriptor is attached to an
irqtype-style controller. This also fixes MSI-X IRQ handling on i386 and
x86_64.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms to disable the automatic enabling of freshly set up irqs.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms to disable request_irq() for certain interrupts.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable platforms that do not have a hardware-assisted hardirq-resend mechanism
to resend them via a softirq-driven IRQ emulation mechanism.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add ->retrigger() irq op to consolidate hw_irq_resend() implementations.
(Most architectures had it defined to NOP anyway.)
NOTE: ia64 needs testing. i386 and x86_64 tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidation: remove the pending_irq_cpumask[NR_IRQS] array and move it into
the irq_desc[NR_IRQS].pending_mask field.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidation: remove the irq_dir[NR_IRQS] and the smp_affinity_entry[NR_IRQS]
arrays and move them into the irq_desc[] array.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Small cleanups in include/linux/irq.h.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup: remove irq_desc_t use from the generic IRQ code, and mark it
obsolete.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that i386 defaults to regparm, explicit uses of fastcall are not needed
anymore.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup: remove irq_descp() - explicit use of irq_desc[] is shorter and more
readable.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidation: remove the irq_affinity[NR_IRQS] array and move it into the
irq_desc[NR_IRQS].affinity field.
[akpm@osdl.org: sparc64 build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch-queue improves the generic IRQ layer to be truly generic, by adding
various abstractions and features to it, without impacting existing
functionality.
While the queue can be best described as "fix and improve everything in the
generic IRQ layer that we could think of", and thus it consists of many
smaller features and lots of cleanups, the one feature that stands out most is
the new 'irq chip' abstraction.
The irq-chip abstraction is about describing and coding and IRQ controller
driver by mapping its raw hardware capabilities [and quirks, if needed] in a
straightforward way, without having to think about "IRQ flow"
(level/edge/etc.) type of details.
This stands in contrast with the current 'irq-type' model of genirq
architectures, which 'mixes' raw hardware capabilities with 'flow' details.
The patchset supports both types of irq controller designs at once, and
converts i386 and x86_64 to the new irq-chip design.
As a bonus side-effect of the irq-chip approach, chained interrupt controllers
(master/slave PIC constructs, etc.) are now supported by design as well.
The end result of this patchset intends to be simpler architecture-level code
and more consolidation between architectures.
We reused many bits of code and many concepts from Russell King's ARM IRQ
layer, the merging of which was one of the motivations for this patchset.
This patch:
rename desc->handler to desc->chip.
Originally i did not want to do this, because it's a big patch. But having
both "desc->handler", "desc->handle_irq" and "action->handler" caused a
large degree of confusion and made the code appear alot less clean than it
truly is.
I have also attempted a dual approach as well by introducing a
desc->chip alias - but that just wasnt robust enough and broke
frequently.
So lets get over with this quickly. The conversion was done automatically
via scripts and converts all the code in the kernel.
This renaming patch is the first one amongst the patches, so that the
remaining patches can stay flexible and can be merged and split up
without having some big monolithic patch act as a merge barrier.
[akpm@osdl.org: build fix]
[akpm@osdl.org: another build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The TPAM isdn driver was removed in 2.6.12, but include/linux/isdn/tpam.h
was missed.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The proposed NFS key type uses its own method of passing key requests to
userspace (upcalling) rather than invoking /sbin/request-key. This is
because the responsible userspace daemon should already be running and will
be contacted through rpc_pipefs.
This patch permits the NFS filesystem to pass auxiliary data to the upcall
operation (struct key_type::request_key) so that the upcaller can use a
pre-existing communications channel more easily.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-By: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix some kernel-doc typos/spellos.
Use kernel-doc syntax in places where it was almost used.
Correct/add struct, struct field, and function param names where needed.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix all kernel-doc warnings in MTD headers and source files:
- add some missing struct fields;
- correct some function parameter names;
- use kernel-doc format for function doc. headers;
- nand_ecc.c contains only exported interfaces, no internal ones;
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
plist.h uses container_of, which is defined in kernel.h.
Include kernel.h in plist.h as the kernel.h include does not longer
happen automatically on all architectures.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds earlier initialization of spi_device.mode, as needed
on boards using nondefault chipselect polarity. An example would be
ones using the RS5C348 RTC without an external signal inverter between
the RTC chipselect and the SPI controller.
Without this mechanism, the first setup() call for that chip would
wrongly enable chips, corrupting transfers to/from other chips sharing
that SPI bus.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the controller FIFO cleared automatically on error we must not try
and drain it as this will hang some chips.
Based in concept on a broken patch from -mm some while back
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make a 1-bit bitfield unsigned (no space for sign bit).
Removes 24 sparse warnings from this one file:
include/linux/ac97_codec.h:262:13: error: dubious one-bit signed bitfield
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove 'active' field from tty buffer structure. This was added in 2.6.16
as part of a patch to make the new tty buffering SMP safe. This field is
unnecessary with the more intelligently written flush_to_ldisc that adds
receive_room handling.
Removing this field reverts to simpler logic where the tail buffer is
always the 'active' buffer, which should not be freed by flush_to_ldisc.
(active == buffer being filled with new data)
The result is simpler, smaller, and faster tty buffer code.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove TTY_DONT_FLIP tty flag. This flag was introduced in 2.1.X kernels
to prevent the N_TTY line discipline functions read_chan() and
n_tty_receive_buf() from running at the same time. 2.2.15 introduced
tty->read_lock to protect access to the N_TTY read buffer, which is the
only state requiring protection between these two functions.
The current TTY_DONT_FLIP implementation is broken for SMP, and is not
universally honored by drivers that send data directly to the line
discipline receive_buf function.
Because TTY_DONT_FLIP is not necessary, is broken in implementation, and is
not universally honored, it is removed.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
