Nothing in include/asm-x86_64/cpufeature.h is part of the
userspace<->kernel interface.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Idle callbacks has some races when enter_idle() sets isidle and subsequent
interrupts that can happen on that CPU, before CPU goes to idle. Due to this,
an IDLE_END can get called before IDLE_START. To avoid these races, disable
interrupts before enter_idle and make sure that all idle routines do not
enable interrupts before entering idle.
Note that poll_idle() still has a this race as it has to enable interrupts
before going to idle. But, all other idle routines have the race fixed.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Tighten the requirements on both input to and output from the Dwarf2
unwinder.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Add sysctl for kstack_depth_to_print. This lets users change
the amount of raw stack data printed in dump_stack() without
having to reboot.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Here is a small patch for x86-64 which adds a cpufeature flag and
detection code for Intel's Branch Trace Store (BTS) feature. This
feature can be found on Intel P4 and Core 2 processors among others.
It can also be used by perfmon.
changelog:
- add CPU_FEATURE_BTS
- add Branch Trace Store detection
signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Move the irqbalance quirks for E7320/E7520/E7525(Errata 23 in
http://download.intel.com/design/chipsets/specupdt/30304203.pdf) to early
quirks.
And add a PCI quirk for these platforms to check(which happens very late
during the boot) if the APIC routing is indeed set to default flat mode.
This fixes the breakage(in x86_64) of this quirk due to cpu hotplug which
selects physical mode instead of the logical flat(as needed for this errata
workaround).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: "Li, Shaohua" <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Mechanism of selecting physical mode in genapic when cpu hotplug is enabled on
x86_64, broke the quirk(quirk_intel_irqbalance()) introduced for working
around the transposing interrupt message errata in E7520/E7320/E7525 (revision
ID 0x9 and below. errata #23 in
http://download.intel.com/design/chipsets/specupdt/30304203.pdf).
This errata requires the mode to be in logical flat, so that interrupts can be
directed to more than one cpu(and thus use hardware IRQ balancing enabled by
BIOS on these platforms).
Following four patches fixes this by moving the quirk to early quirk and
forcing the x86_64 genapic selection to logical flat on these platforms.
Thanks to Shaohua for pointing out the breakage.
This patch:
Add write_pci_config_byte() to direct PCI access routines
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: "Li, Shaohua" <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Make pmd_bad() symmetrical to pgd_bad() and pud_bad(). At once,
simplify them all.
TBD: tighten down the checks again as suggested by Hugh D.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The final line of /proc/<pid>/maps on x86_64 for native 64-bit
tasks shows an incorrect ending address and incorrect permissions. There
is only a single page mapped in this vsyscall region, and it is accessible
for both read and execute.
The patch below fixes this. (Since 32-bit-compat tasks have a real vma
with correct perms/range, no change is necessary for that scenario.)
Before the patch, a "cat /proc/self/maps | tail -1" shows this:
ffffffffff600000-ffffffffffe00000 ---p 00000000 [...]
After the patch, this is the output:
ffffffffff600000-ffffffffff601000 r-xp 00000000 [...]
Signed-off-by: Ernie Petrides <petrides@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
It turns out that the most called ops, by several orders of magnitude,
are the interrupt manipulation ops. These are obvious candidates for
patching, so mark them up and create infrastructure for it.
The method used is that the ops structure has a patch function, which
is called for each place which needs to be patched: this returns a
number of instructions (the rest are NOP-padded).
Usually we can spare a register (%eax) for the binary patched code to
use, but in a couple of critical places in entry.S we can't: we make
the clobbers explicit at the call site, and manually clobber the
allowed registers in debug mode as an extra check.
And:
Don't abuse CONFIG_DEBUG_KERNEL, add CONFIG_DEBUG_PARAVIRT.
And:
AK: Fix warnings in x86-64 alternative.c build
And:
AK: Fix compilation with defconfig
And:
^From: Andrew Morton <akpm@osdl.org>
Some binutlises still like to emit references to __stop_parainstructions and
__start_parainstructions.
And:
AK: Fix warnings about unused variables when PARAVIRT is disabled.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
For both i386 and x86_64, copy from arch/$ARCH/lib/delay.c comments about the
used magic constants, plus a few other niceties.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andi Kleen <ak@suse.de>
include/asm-i386/delay.h | 5 ++++-
include/asm-x86_64/delay.h | 5 ++++-
2 files changed, 8 insertions(+), 2 deletions(-)
Port two patches from i386 to x86_64 delay.c to make sure all rounding is done
upward instead of downward.
There is no sign in commit messages that the mismatch was done on purpose, and
"delay() guarantees sleeping at least for the specified time" is still a valid
rule IMHO.
The original x86 patches are both from pre-GIT era, i.e.:
"[PATCH] round up in __udelay()" in commit
54c7e1f5cc6771ff644d7bc21a2b829308bd126f
"[PATCH] add 1 in __const_udelay()" in commit
42c77a9801b8877d8b90f65f75db758822a0bccc
(both commits are from converted BK repository to x86_64).
AK: fixed gcc warning
linux/arch/x86_64/lib/delay.c:43: warning: suggest parentheses around + or - inside shift
(did this actually work?)
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch makes it possible to compile Calgary in but not use it by
default. In this mode, use 'iommu=calgary' to activate it.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch cleans up the previous "Use BIOS supplied BBAR information"
patch. Mostly stylistic clenaups, but also check for ioremap failure
when we ioremap the BBAR rather than when trying to use it.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Laurent Vivier <Laurent.Vivier@bull.net>
Find the BBAR register address of each Calgary using the "Extended
BIOS Data Area" rather than calculating it ourselves. Also get the bus
topology (what PHB each bus is on) from Calgary rather than
calculating it ourselves.
This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=7407.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Andi Kleen <ak@suse.de>
Code that wants to use struct desc_struct cannot do so on i386 because
desc.h contains other code that will only compile on x86_64.
So extract the structure definitions into a asm-x86_64/desc_defs.h.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andi Kleen <ak@suse.de>
include/asm-x86_64/desc.h | 53 -------------------------------
include/asm-x86_64/desc_defs.h | 69 +++++++++++++++++++++++++++++++++++++++++
2 files changed, 70 insertions(+), 52 deletions(-)
Add o the x86-64 tree a bunch of MSRs related to performance
monitoring for the processors based on Intel Core microarchitecture.
It also adds some architectural MSRs for PEBS. A similar patch for i386 will
follow.
changelog:
- add Intel Precise-Event Based sampling (PEBS) related MSR
- add Intel Data Save (DS) Area related MSR
- add Intel Core microarchitecure performance counter MSRs
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
When a spinlock lockup occurs, arrange for the NMI code to emit an all-cpu
backtrace, so we get to see which CPU is holding the lock, and where.
Cc: Andi Kleen <ak@muc.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
inline function cpu_mask_to_apicid in smp.h is duplicated with macro
in mach_apic.h.
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Here is a patch (used by perfmon2) to detect the presence of the
Precise Event Based Sampling (PEBS) feature for Intel 64-bit processors.
The patch also adds the cpu_has_pebs macro.
changelog:
- adds X86_FEATURE_PEBS
- adds cpu_has_pebs to test for X86_FEATURE_PEBS
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Here is a patch (used by perfmon2) that renamed X86_FEATURE_DTES
to X86_FEATURE_DS to match Intel's documentation for the Debug Store
save area. The patch also adds cpu_has_ds.
changelog:
- rename X86_FEATURE_DTES to X86_FEATURE_DS to match documentation
- adds cpu_has_ds to test for X86_FEATURE_DS
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Any code that relies on the volatile would be a bug waiting to happen
anyway.
Don't encourage people to think that putting 'volatile' on data
structures somehow fixes problems. We should always use proper locking
(and other serialization) techniques.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a resubmission of patches originally created by Ingo Molnar.
The link below is the initial (?) posting of the patch.
http://marc.theaimsgroup.com/?l=linux-kernel&m=115217423929806&w=2
Remove 'volatile' from spinlock_types as it causes GCC to generate bad
code (see link) and locking should be used on kernel data.
Signed-off-by: Art Haas <ahaas@airmail.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_LBD and CONFIG_LSF are spread into asm/types.h for no particularly
good reason.
Centralising the definition in linux/types.h means that arch maintainers
don't need to bother adding it, as well as fixing the problem with
x86-64 users being asked to make a decision that has absolutely no
effect.
The H8/300 porters seem particularly confused since I'm not aware of any
microcontrollers that need to support 2TB filesystems.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* sanitize prototypes, annotate
* usual ntohs->shift
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ACPI to use dev_archdata instead of firmware_data
This patch changes ACPI to use the new dev_archdata on i386, x86_64
and ia64 (is there any other arch using ACPI ?) to store it's
acpi_handle.
It also removes the firmware_data field from struct device as this
was the only user.
Only build-tested on x86
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add arch specific dev_archdata to struct device
Adds an arch specific struct dev_arch to struct device. This enables
architecture to add specific fields to every device in the system, like
DMA operation pointers, NUMA node ID, firmware specific data, etc...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andi Kleen <ak@suse.de>
Acked-By: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When another interrupt happens in exit_idle the exit idle notifier
could be called an incorrect number of times.
Add a test_and_clear_bit_pda and use it handle the bit
atomically against interrupts to avoid this.
Pointed out by Stephane Eranian
Signed-off-by: Andi Kleen <ak@suse.de>
The vgetcpu per CPU initialization previously relied on CPU hotplug
events for all CPUs to initialize the per CPU state. That only
worked only on kernels with CONFIG_HOTPLUG_CPU enabled. On the
others some CPUs didn't get their state initialized properly
and vgetcpu wouldn't work.
Change the initialization sequence to instead run in a normal
initcall (which runs after the normal CPU bootup) and initialize
all running CPUs there. Later hotplug CPUs are still handled
with an hotplug notifier.
This actually simplifies the code somewhat.
Signed-off-by: Andi Kleen <ak@suse.de>
Timer overrides are normally disabled on Nvidia board because
they are commonly wrong, except on new ones with HPET support.
Unfortunately there are quite some Asus boards around that
don't have HPET, but need a timer override.
We don't know yet how to handle this transparently,
but at least add a command line option to force the timer override
and let them boot.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
This is just commit 130fe05dbc ported to
x86-64, for all the same reasons. It cleans up the IO-APIC accesses in
order to then fix the ordering issues.
We move the accessor functions (that were only used by io_apic.c) out of
a header file, and use proper memory-mapped accesses rather than making
up our own "volatile" pointers.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When I generalized __assign_irq_vector I failed to pay attention
to what happens when you access a per cpu data structure for
a cpu that is not online. It is an undefined case making any
code that does it have undefined behavior as well.
The code still needs to be able to allocate a vector across cpus
that are not online to properly handle combinations like lowest
priority interrupt delivery and cpu_hotplug. Not that we can do
that today but the infrastructure shouldn't prevent it.
So this patch updates the places where we touch per cpu data
to only touch online cpus, it makes cpu vector allocation
an atomic operation with respect to cpu hotplug, and it updates
the cpu start code to properly initialize vector_irq so we
don't have inconsistencies.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
By default route the 8254 over the 8259 and only disable
it on ATI boards where this causes double timer interrupts.
This should unbreak some Nvidia boards where the timer doesn't
seem to tick of it isn't enabled in the 8259. At least one
VIA board also seemed to have a little trouble with the disabled
8259.
For 2.6.20 we'll try both dynamically without black listing, but I think
for .19 this is the safer approach because it has been already well tested
in earlier kernels. This also makes the x86-64 behaviour the same
as i386.
Command line options can change all this of course.
Signed-off-by: Andi Kleen <ak@suse.de>
If function change_page_attr_addr calls revert_page to revert
to original pte value, mk_pte_phys does not mask NX bit. If NX bit
is set on no NX hardware supported x86_64 machine, there is will
be RSVD type page fault and system will crash. This patch adds NX
mask bit for PTE entry.
Signed-off-by: bibo,mao <bibo.mao@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
- Fixes a build problem with CONFIG_M386=y (include file dependencies get
messy).
- Share the implementation between x86 and x86_64
- These are too big to inline anyway.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Enable ondemand governor and acpi-cpufreq to use IA32_APERF and IA32_MPERF MSR
to get active frequency feedback for the last sampling interval. This will
make ondemand take right frequency decisions when hardware coordination of
frequency is going on.
Without APERF/MPERF, ondemand can take wrong decision at times due
to underlying hardware coordination or TM2.
Example:
* CPU 0 and CPU 1 are hardware cooridnated.
* CPU 1 running at highest frequency.
* CPU 0 was running at highest freq. Now ondemand reduces it to
some intermediate frequency based on utilization.
* Due to underlying hardware coordination with other CPU 1, CPU 0 continues to
run at highest frequency (as long as other CPU is at highest).
* When ondemand samples CPU 0 again next time, without actual frequency
feedback from APERF/MPERF, it will think that previous frequency change
was successful and can go to wrong target frequency. This is because it
thinks that utilization it has got this sampling interval is when running at
intermediate frequency, rather than actual highest frequency.
More information about IA32_APERF IA32_MPERF MSR:
Refer to IA-32 Intel® Architecture Software Developer's Manual at
http://developer.intel.com
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Intel processors starting with the Core Duo support
support processor native C-state using the MWAIT instruction.
Refer: Intel Architecture Software Developer's Manual
http://www.intel.com/design/Pentium4/manuals/253668.htm
Platform firmware exports the support for Native C-state to OS using
ACPI _PDC and _CST methods.
Refer: Intel Processor Vendor-Specific ACPI: Interface Specification
http://www.intel.com/technology/iapc/acpi/downloads/302223.htm
With Processor Native C-state, we use 'MWAIT' instruction on the processor
to enter different C-states (C1, C2, C3). We won't use the special IO
ports to enter C-state and no SMM mode etc required to enter C-state.
Overall this will mean better C-state support.
One major advantage of using MWAIT for all C-states is, with this and
"treat interrupt as break event" feature of MWAIT, we can now get accurate
timing for the time spent in C1, C2, .. states.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
There's nothing arch-specific about check_signature(), so move it to
<linux/io.h>. Use a cross between the Alpha and i386 implementations as
the generic one.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The problem we can't take advantage of lowest priority delivery mode if
the vectors are allocated for only one cpu at a time. Nor can we work
around hardware that assumes lowest priority delivery mode is always
used with several cpus.
So this patch introduces the concept of a vector_allocation_domain. A
set of cpus that will receive an irq on the same vector. Currently the
code for implementing this is placed in the genapic structure so we can
vary this depending on how we are using the io_apics.
This allows us to restore the previous behaviour of genapic_flat without
removing the benefits of having separate vector allocation for large
machines.
This should also fix the problem report where a hyperthreaded cpu was
receving the irq on the wrong hyperthread when in logical delivery mode
because the previous behaviour is restored.
This patch properly records our allocation of the first 16 irqs to the
first 16 available vectors on all cpus. This should be fine but it may
run into problems with multiple interrupts at the same interrupt level.
Except for some badly maintained comments in the code and the behaviour
of the interrupt allocator I have no real understanding of that problem.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Which vector an irq is assigned to now varies dynamically and is
not needed outside of io_apic.c. So remove the possibility
of accessing the information outside of io_apic.c and remove
the silly macro that makes looking for users of irq_vector
difficult.
The fact this compiles ensures there aren't any more pieces
of the old CONFIG_PCI_MSI weirdness that I failed to remove.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Trivial typo fix in the "syntax error if percpu macros are incorrectly
used" patch. I misspelled "identifier" in all places. D'Oh!
Thanks to Dirk Mueller to point this out.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
* master.kernel.org:/pub/scm/linux/kernel/git/davej/configh:
Remove all inclusions of <linux/config.h>
Manually resolved trivial path conflicts due to removed files in
the sound/oss/ subdirectory.
It turns out msi_ops was simply not enough to abstract the architecture
specific details of msi. So I have moved the resposibility of constructing
the struct irq_chip to the architectures, and have two architecture specific
functions arch_setup_msi_irq, and arch_teardown_msi_irq.
For simple architectures those functions can do all of the work. For
architectures with platform dependencies they can call into the appropriate
platform code.
With this msi.c is finally free of assuming you have an apic, and this
actually takes less code.
The helpers for the architecture specific code are declared in the linux/msi.h
to keep them separate from the msi functions used by drivers in linux/pci.h
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements two functions ht_create_irq and ht_destroy_irq for
use by drivers. Several other functions are implemented as helpers for
arch specific irq_chip handlers.
The driver for the card I tested this on isn't yet ready to be merged.
However this code is and hypertransport irqs are in use in a few other
places in the kernel. Not that any of this will get merged before 2.6.19
Because the ipath-ht400 is slightly out of spec this code will need to be
generalized to work there.
I think all of the powerpc uses are for a plain interrupt controller in a
chipset so support for native hypertransport devices is a little less
interesting.
However I think this is a half way decent model on how to separate arch
specific and generic helper code, and I think this is a functional model of
how to get the architecture dependencies out of the msi code.
[akpm@osdl.org: Kconfig fix]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With more irqs in the system we don't need this.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This refactors the irq handling code to make the vectors a per cpu resource so
the same vector number can be simultaneously used on multiple cpus for
different irqs.
This should make systems that were hitting limits on the total number of irqs
much more livable.
[akpm@osdl.org: build fix]
[akpm@osdl.org: __target_IO_APIC_irq is unneeded on UP]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a small pessimization but it paves the way for making this information
per cpu. Which allows the the maximum number of IRQS to become NR_CPUS*224.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for systems that cannot receive every interrupt on a
single cpu simultaneously, in the check to see if we have enough HARDIRQ_BITS.
MAX_HARDIRQS_PER_CPU becomes the count of the maximum number of hardare
generated interrupts per cpu.
On architectures that support per cpu interrupt delivery this can be a
significant space savings and scalability bonus.
This patch adds support for systems that cannot receive every interrupt on
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the change in behavior of the irq allocation code when
CONFIG_PCI_MSI is defined. Removing all instances of the assumption that irq
== vector.
create_irq is rewritten to first allocate a free irq and then to assign that
irq a vector.
assign_irq_vector is made static and the AUTO_ASSIGN case which allocates an
vector not bound to an irq is removed.
The ioapic vector methods are removed, and everything now works with irqs.
The definition of NR_IRQS no longer depends on CONFIG_PCI_MSI
[akpm@osdl.org: cleanup]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the change in behavior of the irq allocation code when
CONFIG_PCI_MSI is defined. Removing all instances of the assumption that irq
== vector.
create_irq is rewritten to first allocate a free irq and then to assign that
irq a vector.
assign_irq_vector is made static and the AUTO_ASSIGN case which allocates an
vector not bound to an irq is removed.
The ioapic vector methods are removed, and everything now works with irqs.
The definition of NR_IRQS no longer depends on CONFIG_PCI_MSI
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes the hardcoded assumption that irq == vector in the msi
composition code, and it allows the msi message composition to setup logical
mode, or lowest priorirty delivery mode as we do for other apic interrupts,
and with the same selection criteria.
Basically this moves the problem of what is in the msi message into the
architecture irq management code where it belongs. Not in a generic layer
that doesn't have enough information to compose msi messages properly.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts all the x86_64 PIC controllers layers to the new and
simpler irq-chip interrupt handling layer.
[mingo@elte.hu: The patch also enables the fasteoi handler for x86_64]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Introduce the child field in sched_domain struct and use it in
sched_balance_self().
We will also use this field in cleaning up the sched group cpu_power
setup(done in a different patch) code.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some architectures provide an execve function that does not set errno, but
instead returns the result code directly. Rename these to kernel_execve to
get the right semantics there. Moreover, there is no reasone for any of these
architectures to still provide __KERNEL_SYSCALLS__ or _syscallN macros, so
remove these right away.
[akpm@osdl.org: build fix]
[bunk@stusta.de: build fix]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andi Kleen <ak@muc.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the regs_return_value() macro to extract the return value in an
architecture agnostic manner, given the pt_regs.
Other architecture maintainers may want to add similar helpers.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With 2.6.18-rc4-mm2, now wall_jiffies will always be the same as jiffies.
So we can kill wall_jiffies completely.
This is just a cleanup and logically should not change any real behavior
except for one thing: RTC updating code in (old) ppc and xtensa use a
condition "jiffies - wall_jiffies == 1". This condition is never met so I
suppose it is just a bug. I just remove that condition only instead of
kill the whole "if" block.
[heiko.carstens@de.ibm.com: s390 build fix and cleanup]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On systems running with virtual cpus there is optimization potential in
regard to spinlocks and rw-locks. If the virtual cpu that has taken a lock
is known to a cpu that wants to acquire the same lock it is beneficial to
yield the timeslice of the virtual cpu in favour of the cpu that has the
lock (directed yield).
With CONFIG_PREEMPT="n" this can be implemented by the architecture without
common code changes. Powerpc already does this.
With CONFIG_PREEMPT="y" the lock loops are coded with _raw_spin_trylock,
_raw_read_trylock and _raw_write_trylock in kernel/spinlock.c. If the lock
could not be taken cpu_relax is called. A directed yield is not possible
because cpu_relax doesn't know anything about the lock. To be able to
yield the lock in favour of the current lock holder variants of cpu_relax
for spinlocks and rw-locks are needed. The new _raw_spin_relax,
_raw_read_relax and _raw_write_relax primitives differ from cpu_relax
insofar that they have an argument: a pointer to the lock structure.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As suggested by Muli Ben-Yehuda this function is moved to generic code as
may be useful for all archs.
[akpm@osdl.org: fix]
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consistently use MAX_ERRNO when checking for errors in __syscall_return().
[ralf@linux-mips.org: build fix]
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need processor.h for cpu_relax().
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (225 commits)
[PATCH] Don't set calgary iommu as default y
[PATCH] i386/x86-64: New Intel feature flags
[PATCH] x86: Add a cumulative thermal throttle event counter.
[PATCH] i386: Make the jiffies compares use the 64bit safe macros.
[PATCH] x86: Refactor thermal throttle processing
[PATCH] Add 64bit jiffies compares (for use with get_jiffies_64)
[PATCH] Fix unwinder warning in traps.c
[PATCH] x86: Allow disabling early pci scans with pci=noearly or disallowing conf1
[PATCH] x86: Move direct PCI scanning functions out of line
[PATCH] i386/x86-64: Make all early PCI scans dependent on CONFIG_PCI
[PATCH] Don't leak NT bit into next task
[PATCH] i386/x86-64: Work around gcc bug with noreturn functions in unwinder
[PATCH] Fix some broken white space in ia32_signal.c
[PATCH] Initialize argument registers for 32bit signal handlers.
[PATCH] Remove all traces of signal number conversion
[PATCH] Don't synchronize time reading on single core AMD systems
[PATCH] Remove outdated comment in x86-64 mmconfig code
[PATCH] Use string instructions for Core2 copy/clear
[PATCH] x86: - restore i8259A eoi status on resume
[PATCH] i386: Split multi-line printk in oops output.
...
The use of SEGMENT_RPL_MASK in the i386 ptrace.h introduced by
x86-allow-a-kernel-to-not-be-in-ring-0.patch broke the UML build, as UML
includes the underlying architecture's ptrace.h, but has no easy access to the
x86 segment definitions.
Rather than kludging around this, as in the past, this patch splits the
userspace-usable parts, which are the bits that UML needs, of ptrace.h into
ptrace-abi.h, which is included back into ptrace.h. Thus, there is no net
effect on i386.
As a side-effect, this creates a ptrace header which is close to being usable
in /usr/include.
x86_64 is also treated in this way for consistency. There was some trailing
whitespace there, which is cleaned up.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On x86_64 machines with more than 2 GB of RAM there are large memory gaps
(with no corresponding kernel virtual addresses) and reserved memory
regions between areas of usable physical RAM. Moreover, if CONFIG_FLATMEM
is set, they appear within the normal zone. swsusp should not try to save
them, so the corresponding page structs have to be marked as 'nosave'.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we're going to implement smp_call_function_single() on three architecture
with the same prototype then it should have a declaration in a
non-arch-specific header file.
Move it into <linux/smp.h>.
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One of the changes necessary for shared page tables is to standardize the
pxx_page macros. pte_page and pmd_page have always returned the struct
page associated with their entry, while pte_page_kernel and pmd_page_kernel
have returned the kernel virtual address. pud_page and pgd_page, on the
other hand, return the kernel virtual address.
Shared page tables needs pud_page and pgd_page to return the actual page
structures. There are very few actual users of these functions, so it is
simple to standardize their usage.
Since this is basic cleanup, I am submitting these changes as a standalone
patch. Per Hugh Dickins' comments about it, I am also changing the
pxx_page_kernel macros to pxx_page_vaddr to clarify their meaning.
Signed-off-by: Dave McCracken <dmccr@us.ibm.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
get_cpu_var()/per_cpu()/__get_cpu_var() arguments must be simple
identifiers. Otherwise the arch dependent implementations might break.
This patch enforces the correct usage of the macros by producing a syntax
error if the variable is not a simple identifier.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Refactor the event processing (syslog messaging and rate limiting)
into separate file therm_throt.c. This allows consistent reporting
of CPU thermal throttle events.
After ACK'ing the interrupt, if the event is current, the user
(p4.c/mce_intel.c) calls therm_throt_process to log (and rate limit)
the event. If that function returns 1, the user has the option to log
things further (such as to mce_log in x86_64).
AK: minor cleanup
Signed-off-by: Dmitriy Zavin <dmitriyz@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix
linux/arch/x86_64/kernel/traps.c: In function 'dump_trace':
linux/arch/x86_64/kernel/traps.c:275: warning: cast to pointer from integer of different size
with allnoconfig
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Some buggy systems can machine check when config space accesses
happen for some non existent devices. i386/x86-64 do some early
device scans that might trigger this. Allow pci=noearly to disable
this. Also when type 1 is disabling also don't do any early
accesses which are always type1.
This moves the pci= configuration parsing to be a early parameter.
I don't think this can break anything because it only changes
a single global that is only used by PCI.
Cc: gregkh@suse.de
Cc: Trammell Hudson <hudson@osresearch.net>
Signed-off-by: Andi Kleen <ak@suse.de>
SYSENTER can cause a NT to be set which might cause crashes on the IRET
in the next task.
Following similar i386 patch from Linus.
Signed-off-by: Andi Kleen <ak@suse.de>
Current gcc generates calls not jumps to noreturn functions. When that happens the
return address can point to the next function, which confuses the unwinder.
This patch works around it by marking asynchronous exception
frames in contrast normal call frames in the unwind information. Then teach
the unwinder to decode this.
For normal call frames the unwinder now subtracts one from the address which avoids
this problem. The standard libgcc unwinder uses the same trick.
It doesn't include adjustment of the printed address (i.e. for the original
example, it'd still be kernel_math_error+0 that gets displayed, but the
unwinder wouldn't get confused anymore.
This only works with binutils 2.6.17+ and some versions of H.J.Lu's 2.6.16
unfortunately because earlier binutils don't support .cfi_signal_frame
[AK: added automatic detection of the new binutils and wrote description]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Previously exit_idle would be called more often than enter_idle
Now instead of using complicated tests just keep track of it
using the per CPU variable as a flip flop. I moved the idle state into the
PDA to make the access more efficient.
Original bug report and an initial patch from Stephane Eranian,
but redone by AK.
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Reindent the macros in x86-64 pda.h, making them much more readable.
Follows Jeremy's i386 version of this.
No functional changes
Signed-off-by: Andi Kleen <ak@suse.de>
- Don't zero for __copy_from_user_inatomic following i386.
This will prevent spurious zeros for parallel file system writers when
one does a exception
- The string instruction version didn't zero the output on
exception. Oops.
Also I cleaned up the code a bit while I was at it and added a minor
optimization to the string instruction path.
Signed-off-by: Andi Kleen <ak@suse.de>
I just added type checking for assignments the PDA in the i386 PDA code.
Here's the x86-64 equivalent. (Obviously this doesn't contain the latest
x86-64 PDA change.)
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch adds the per thread cookie field to the task struct and the PDA.
Also it makes sure that the PDA value gets the new cookie value at context
switch, and that a new task gets a new cookie at task creation time.
Signed-off-by: Arjan van Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
CC: Andi Kleen <ak@suse.de>
Change the comments in the pda structure to make the first fields to have
their offset documented and to have the comments aligned.
The stack protector series needs a field at offset 40 (gcc ABI); annotate
upto 40 for that reason.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
CC: Andi Kleen <ak@suse.de>
kexec: Avoid overwriting the current pgd (V4, x86_64)
This patch upgrades the x86_64-specific kexec code to avoid overwriting the
current pgd. Overwriting the current pgd is bad when CONFIG_CRASH_DUMP is used
to start a secondary kernel that dumps the memory of the previous kernel.
The code introduces a new set of page tables. These tables are used to provide
an executable identity mapping without overwriting the current pgd.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Remove most of the special cases for the debug IST stack. This is a
follow on clean up patch, it requires the bug fix patch that adds
orig_ist.
Signed-off-by: Keith Owens <kaos@ocs.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Based on a idea by Jeremy Fitzhardinge:
Replace the volatiles and memory clobbers in the PDA access with
telling gcc about access to a proxy PDA structure that doesn't
actually exist. But the dummy accesses give a defined ordering for
read/write accesses.
Also add some memory barriers to the early GS initialization to
make sure no PDA access is moved before it.
Advantage is some .text savings (probably most from better
code for accessing "current"):
text data bss dec hex filename
4845647 1223688 615864 6685199 66020f vmlinux
4837780 1223688 615864 6677332 65e354 vmlinux-pda
1.2% smaller code
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andi Kleen <ak@suse.de>
