We do not need to have llds set the host no for the session's
parent, because we know the session's parent is going to be
the host. This removes it from the session creation callback
and converts the drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The qdepth setting was useful when we needed libiscsi to verify
the setting. Now we just need to make sure if older tools
passed in zero then we need to set some default.
So this patch just has us use the sht->cmd_per_lun or if
for LLD does a host per session then we can set it on per
host basis.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We were using the shost work queue which ended up being
a little akward since all iscsi hosts need a thread for
scanning, but only drivers hooked into libiscsi need
a workqueue for transmitting. So this patch moves the
xmit workqueue to the lib.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is no need to cap the queue depth in the modules. We set
this in userspace and can do that there. For performance testing
with ram based targets, this is helpful since we can have very
high queue depths.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iser has its own logging inrfastrucutre. Convert it to use
it instead of libiscsi.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove hard setting of the IB MTU used by iSER's RC queue-pair to 1K,
as this was done due to inter-op issues with an old iser target which
is not used any more.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix ib_iser build to depend on INFINIBAND_ADDR_TRANS; if INET=y but
IPV6=n, then the RDMA CM is not built but INFINIBAND_ISER can be
enabled, leading to:
ERROR: "rdma_destroy_id" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_connect" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_destroy_qp" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_create_id" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_create_qp" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_resolve_route" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_disconnect" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
ERROR: "rdma_resolve_addr" [drivers/infiniband/ulp/iser/ib_iser.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
We do not need to allocate a itt for data_out, so this
passes the opcode to the alloc_pdu callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This just converts iser to new alloc_pdu api. It still
preallocates the pdu, so there is no difference.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
iSCSI/iSER targets may send PDUs without a prior request from the
initiator. RFC 5046 refers to these PDUs as "unexpected". NOP-In PDUs
with itt=RESERVED and Asynchronous Message PDUs occupy this category.
The amount of active "unexpected" PDU's an iSER target may have at any
time is governed by the MaxOutstandingUnexpectedPDUs key, which is not
yet supported.
Currently when an iSER target sends an "unexpected" PDU, the
initiators recv buffer consumed by the PDU is not replaced. If over
initial_post_recv_bufs_num "unexpected" PDUs are received then the
receive queue will run out of receive work requests entirely.
This patch ensures recv buffers consumed by "unexpected" PDUs are
replaced in the next iser_post_receive_control() call.
Signed-off-by: David Disseldorp <ddiss@sgi.com>
Signed-off-by: Ken Sandars <ksandars@sgi.com>
Acked-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I had this in my patchset to add target reset support, but
it got dropped due to patching conflicts. This initial patch
just renames the function and users. We are actually just
dropping the session, and so this does not have anything to do
with the host exactly. It does for software iscsi because
we allocate a host per session, but for cxgb3i this makes no
sense.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If the driver knows when hardware is removed like with cxgb3i,
bnx2i, qla4xxx and iser then we will want to remove the sessions/devices
that are bound to that device before removing the host.
cxgb3i and in the future bnx2i will remove the host and that will
remove all the sessions on the hba. iser can call iscsi_kill_session
when it gets an event that indicates that a hca is removed.
And when qla4xxx is hooked in to the lib (it is only hooked into
the class right now) it can call iscsi remove host like the
partial offload card drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enhance iser to act upon notification on network stack changes that
make its RDMA connection unaligned with the link used by the stack for
the <src,dst> IPs used to establish the connection.
When RDMA_CM_EVENT_ADDR_CHANGE arrives, just disconnect the
connection, assuming that the user space iscsid daemon will reconnect,
and the new connection will be aligned with the IP stack.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (102 commits)
[SCSI] scsi_dh: fix kconfig related build errors
[SCSI] sym53c8xx: Fix bogus sym_que_entry re-implementation of container_of
[SCSI] scsi_cmnd.h: remove double inclusion of linux/blkdev.h
[SCSI] make struct scsi_{host,target}_type static
[SCSI] fix locking in host use of blk_plug_device()
[SCSI] zfcp: Cleanup external header file
[SCSI] zfcp: Cleanup code in zfcp_erp.c
[SCSI] zfcp: zfcp_fsf cleanup.
[SCSI] zfcp: consolidate sysfs things into one file.
[SCSI] zfcp: Cleanup of code in zfcp_aux.c
[SCSI] zfcp: Cleanup of code in zfcp_scsi.c
[SCSI] zfcp: Move status accessors from zfcp to SCSI include file.
[SCSI] zfcp: Small QDIO cleanups
[SCSI] zfcp: Adapter reopen for large number of unsolicited status
[SCSI] zfcp: Fix error checking for ELS ADISC requests
[SCSI] zfcp: wait until adapter is finished with ERP during auto-port
[SCSI] ibmvfc: IBM Power Virtual Fibre Channel Adapter Client Driver
[SCSI] sg: Add target reset support
[SCSI] lib: Add support for the T10 (SCSI) Data Integrity Field CRC
[SCSI] sd: Move scsi_disk() accessor function to sd.h
...
This patch fixes two bugs that are related.
1. Old tools did not set can_queue/cmds_max. This patch modifies
libiscsi so that when we add the host we catch this and set it
to the default.
2. iscsi_tcp thought that the scsi command that was passed to
the eh functions needed a iscsi_cmd_task allocated for it. It
only needed a mgmt task, and now it does not matter since it
all comes from the same pool and libiscsi handles this for the
drivers. ib_iser had copied iscsi_tcp's code and set can_queue
to its max - 1 to handle this. So this patch removes the max -1,
and just sets it to the max.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The recv lock was defined so the iscsi layer could block
the recv path from processing IO during recovery. It
turns out iser just set a lock to that pointer which was pointless.
We now disconnect the transport connection before doing recovery
so we do not need the recv lock. For iscsi_tcp we still stop
the recv path incase older tools are being used.
This patch also has iscsi_itt_to_ctask user grab the session lock
and has the caller access the task with the lock or get a ref
to it in case the target is broken and sends a tmf success response
then sends data or a response for the command that was supposed to
be affected bty the tmf.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds two new attrs used for creating initiator ports and
binding sessions to hardware.
The session level initiatorname:
Since bnx2i does a scsi_host per host device, we need to add the
iface initiator port settings on the session, so we can create
multiple initiator ports (each with different inames) per device/scsi_host.
The current iname reflects that qla4xxx can have one iname per hba, and we are
allocating a host per session for software. The iname on the host will
remain so we can export and set the hba level qla4xxx setting.
The ifacename attr:
To bind a session to a some peice of hardware in userspace we maintain
some mappings, but during boot or iscsid restart (iscsid contains the user
space part of the driver) we need to be able to figure out which of those
host mappings abstractions maps to certain sessions. This patch adds
a ifacename attr, which userspace can set to id the host side of the
endpoint across pivot_roots and iscsid restarts.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This hooks iser into the iscsi endpoint code. Previously it handled the
lookup and allocation. This has been made generic so bnx2i and iser can
share it. It also allows us to pass iser the leading conn's ep, so we
know the ib_deivce being used and can set it as the scsi_host's parent.
And that allows scsi-ml to set the dma_mask based on those values.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently we duplicate the list of sessions, because we were using the
test for if a session was on the host list to indicate if the session
was bound or unbound. We can instead use the target_id and fix up
the class so that drivers like bnx2i do not have to manage the target id
space.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This handles the iscsi_cmd_task rename and renames
the iser cmd task to iser task.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert ib_iser to support merged tasks.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently to get a ctask from the session cmd array, you have to
know to use the itt modifier. To make this easier on LLDs and
so in the future we can easilly kill the session array and use
the host shared map instead, this patch adds a nice wrapper
to strip the itt into a session->cmds index and return a ctask.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After the stop_conn callback has returned the LLD should not
touch the scsi cmds. iscsi_tcp and libiscsi use the
conn->recv_lock and suspend_rx field to halt recv path
processing, but iser does not have any protection.
This patch modifies iser so that userspace can just
call the ep_disconnect callback, which will halt
all recv IO, before calling the stop_conn callback so
we do not have to worry about the conn->recv_lock and
suspend rx field. iser just needs to stop the send side
from accessing the ib conn.
Fixup to handle when the ep poll fails and ep disconnect
is called from Erez.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This removes the session and conn data_size fields from the iscsi_transport.
Just pass in the value like with host allocation. This patch also makes
it so the LLD iscsi_conn data is allocated with the iscsi_cls_conn.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This finishes the host/session unbinding, by adding some helpers
to add and remove hosts and the session they manage.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bnx2i allocates a host per netdevice but will use libiscsi,
so this unbinds the session from the host in that code.
This will also be useful for the iser parent device dma settings
fixes.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
max_cmd_len and max_conn are not really used. max_cmd_len is
always 16 and can be set by the LLD. max_conn is always one
since we do not support MCS.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iscsi offload (bnx2i and qla4xx) allocate a scsi host per hba,
so the session creation path needs a shost/host_no argument.
Software iscsi/iser will follow the same behabior as before
where it allcoates a host per session, but in the future iser
will probably look more like bnx2i where the host's parent is
the hardware (rnic for iser and for bnx2i it is the nic), because
it does not use a socket layer like how iscsi_tcp does.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Count FMR alignment violations per session as part of the iscsi
statistics.
Signed-off-by: Eli Dorfman <elid@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The itt field in struct iscsi_data is not defined with any particular
endianness. open-iscsi should use it as-is without byte-swapping it.
This fixes sparse warnings coming from doing ntohl(hdr->itt).
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a RDMA_CM_EVENT_DEVICE_REMOVAL event is raised, iSER should
release the connection resources.
This is necessary when the IB HCA module is unloaded while open-iscsi
is still running. Currently, iSER just BUG()s.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
"iser_device" allocation failure is "handled" with a BUG_ON() right
before dereferencing the NULL-pointer - fix this!
Signed-off-by: Arne Redlich <arne.redlich@xiranet.com>
Signed-off-by: Erez Zilber <erezz@voltaire.com>
The iteration through the list of "iser_device"s during device
lookup/creation is broken -- it might result in an infinite loop if
more than one HCA is used with iSER. Fix this by using
list_for_each_entry() instead of the open-coded flawed list iteration
code.
Signed-off-by: Arne Redlich <arne.redlich@xiranet.com>
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
Add a .change_queue_depth handler to the scsi_host_template in the
iSER driver. iscsi_change_queue_depth was added to iscsi_tcp in order
to solve the problem of queue depth which was too high for some
targets. It is also applicable for iSER.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some RDMA CM events are not supported or not handled in iSER.
This patch adds some info (printk) for the user about them.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
eh_device_reset_handler was already added to scsi_host_template
in iscsi_tcp, and is now added also for iscsi_iser.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert xmit to iscsi chunks.
from michaelc@cs.wisc.edu:
Bug fixes, more digest integration, sg chaining conversion and other
sg wrapper changes, coding style sync up, and removal of io fields,
like pdu_sent, that are not needed.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During root boot and shutdown the target could send us nops.
At this time iscsid cannot be running, so the target will drop
the session and the boot or shutdown will hang.
To handle this and allow us to better control when to check the network
this patch moves the nop handling to the kernel.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is not need to block the session during logout. Since
we are going to fail the commands that were blocked just fail them
immediately instead.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- The default initialization of hdr_max is the minimum -
sizeof(struct iscsi_cmd) - Once this patch goes into iser the default
initialization at libiscsi can be removed.
- This is not yet full support for AHSs at iser end. But it should be easy.
Just allocate more space at iser_desc right after iscsi_hdr. Than
at transmission time use ctask->hdr_len to retrieve the total
size of all iscsi pdu headers. See previous patch at iscsi_tcp.[ch]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
