* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Convert to NAPI
IB: Return "maybe missed event" hint from ib_req_notify_cq()
IB: Add CQ comp_vector support
IB/ipath: Fix a race condition when generating ACKs
IB/ipath: Fix two more spin lock problems
IB/fmr_pool: Add prefix to all printks
IB/srp: Set proc_name
IB/srp: Add orig_dgid sysfs attribute to scsi_host
IPoIB/cm: Don't crash if remote side uses one QP for both directions
RDMA/cxgb3: Support for new abort logic
RDMA/cxgb3: Initialize cpu_idx field in cpl_close_listserv_req message
RDMA/cxgb3: Fail qp creation if the requested max_inline is too large
RDMA/cxgb3: Fix TERM codes
IPoIB/cm: Fix error handling in ipoib_cm_dev_open()
IB/ipath: Don't corrupt pending mmap list when unmapped objects are freed
IB/mthca: Work around kernel QP starvation
IB/ipath: Don't put QP in timeout queue if waiting to send
IB/ipath: Don't call spin_lock_irq() from interrupt context
Convert the IP-over-InfiniBand network device driver over to using
NAPI to handle completions for the main CQ. This covers all receives
as well as datagram mode sends; send completions for connected mode
connections are still handled from interrupt context.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The semantics defined by the InfiniBand specification say that
completion events are only generated when a completions is added to a
completion queue (CQ) after completion notification is requested. In
other words, this means that the following race is possible:
while (CQ is not empty)
ib_poll_cq(CQ);
// new completion is added after while loop is exited
ib_req_notify_cq(CQ);
// no event is generated for the existing completion
To close this race, the IB spec recommends doing another poll of the
CQ after requesting notification.
However, it is not always possible to arrange code this way (for
example, we have found that NAPI for IPoIB cannot poll after
requesting notification). Also, some hardware (eg Mellanox HCAs)
actually will generate an event for completions added before the call
to ib_req_notify_cq() -- which is allowed by the spec, since there's
no way for any upper-layer consumer to know exactly when a completion
was really added -- so the extra poll of the CQ is just a waste.
Motivated by this, we add a new flag "IB_CQ_REPORT_MISSED_EVENTS" for
ib_req_notify_cq() so that it can return a hint about whether the a
completion may have been added before the request for notification.
The return value of ib_req_notify_cq() is extended so:
< 0 means an error occurred while requesting notification
== 0 means notification was requested successfully, and if
IB_CQ_REPORT_MISSED_EVENTS was passed in, then no
events were missed and it is safe to wait for another
event.
> 0 is only returned if IB_CQ_REPORT_MISSED_EVENTS was
passed in. It means that the consumer must poll the
CQ again to make sure it is empty to avoid the race
described above.
We add a flag to enable this behavior rather than turning it on
unconditionally, because checking for missed events may incur
significant overhead for some low-level drivers, and consumers that
don't care about the results of this test shouldn't be forced to pay
for the test.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API. Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value. Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.
We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity. This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a problem where simple ACKs can be sent ahead of RDMA read
responses thus implicitly NAKing the RDMA read.
Signed-off-by: Ralph Campbell <ralph.cambpell@qlogic.com>
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a missing unlock in ipath_rc_rcv_resp() and remove an extra unlock
from ipath_rc_rcv_error().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an orig_dgid attribute in sysfs for SRP scsi_hosts, so that
userspace can tell what the original dgid value written to the
add_target file was, even if the connection is redirected to a
different port while connecting.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPoIB CM spec allows the use of a single connection in both
active->passive and passive->active directions. The current Linux
code uses one connection for both directions, but if another node only
uses one connection for both directions, we oops when we try to look
up the passive connection. Fix by checking that qp_context is
non-NULL before dereferencing it.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
The HW now posts 2 ABORT_RPL and/or PEER_ABORT_REQ messages. We need
to handle them by silenty dropping the 1st but mark that we're ready
for the final message. This plugs some close races between the uP and
HW. Also update the minimum required firmware version.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These are all the remaining instances of get_property. Simple rename of
get_property to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix TERMINATE layer, type, and ecode values based on
conformance testing.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If skb allocation fails when we start the device, we call
ipoib_cm_dev_stop() even though ipoib_cm_dev_open() did not run to
completion, so we pass an invalid pointer to ib_destroy_cm_id and get
an oops.
Fix by clearing cm.id on error, and testing it in cm_dev_stop().
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=561>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the pending mmap code so it doesn't corrupt the list of pending
mmaps and crash the machine when pending mmaps are destroyed without
first being mapped. Also, remove an unused variable, and use standard
kernel lists instead of our own homebrewed linked list implementation
to keep the pending mmap list.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With mthca, RC QPs can starve each other and even UD QPs on the same
hardware schedule queue. As a result, userspace MPI can starve
e.g. IPoIB traffic, with netdev watchdog warnings getting printed out,
and TCP connections getting stuck or failing.
Reduce the chance of this happening by using three separate hardware
schedule queues: one for userspace RC QPs, one for kernel RC QPs, and
one for all other QPs.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fixes a problem which causes too many RC timeouts and
retransmits.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the problem reported by Bernd Schubert <bs@q-leap.de>
with kernel debug options enabled:
BUG: at kernel/lockdep.c:1860 trace_hardirqs_on()
This was caused by using spin_lock_irq()/spin_unlock_irq() from
interrupt context. Fix all the places that might be called from
interrupts to use spin_lock_irqsave()/spin_unlock_irqrestore().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband: (49 commits)
IB: Set class_dev->dev in core for nice device symlink
IB/ehca: Implement modify_port
IB/umad: Clarify documentation of transaction ID
IPoIB/cm: spin_lock_irqsave() -> spin_lock_irq() replacements
IB/mad: Change SMI to use enums rather than magic return codes
IB/umad: Implement GRH handling for sent/received MADs
IB/ipoib: Use ib_init_ah_from_path to initialize ah_attr
IB/sa: Set src_path_bits correctly in ib_init_ah_from_path()
IB/ucm: Simplify ib_ucm_event()
RDMA/ucma: Simplify ucma_get_event()
IB/mthca: Simplify CQ cleaning in mthca_free_qp()
IB/mthca: Fix mthca_write_mtt() on HCAs with hidden memory
IB/mthca: Update HCA firmware revisions
IB/ipath: Fix WC format drift between user and kernel space
IB/ipath: Check that a UD work request's address handle is valid
IB/ipath: Remove duplicate stuff from ipath_verbs.h
IB/ipath: Check reserved memory keys
IB/ipath: Fix unit selection when all CPU affinity bits set
IB/ipath: Don't allow QPs 0 and 1 to be opened multiple times
IB/ipath: Disable IB link earlier in shutdown sequence
...
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Now to convert the last one, skb->data, that will allow many simplifications
and removal of some of the offset helpers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that it is also an offset from skb->head, reduces its size from 8 to 4 bytes
on 64bit architectures, allowing us to combine the 4 bytes hole left by the
layer headers conversion, reducing struct sk_buff size to 256 bytes, i.e. 4
64byte cachelines, and since the sk_buff slab cache is SLAB_HWCACHE_ALIGN...
:-)
Many calculations that previously required that skb->{transport,network,
mac}_header be first converted to a pointer now can be done directly, being
meaningful as offsets or pointers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->h.raw = skb->data' operation, so that we can
later turn skb->h.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple cases:
skb->h.raw = skb->data;
skb->h.raw = {skb_push|[__]skb_pull}()
The next ones will handle the slightly more "complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All RDMA drivers except ehca set class_dev->dev to their dma_device
value (ehca leaves this unset). dma_device is the only value that
makes any sense, so move this assignment to core/sysfs.c. This reduce
the duplicated code in the rest of the drivers and gives ehca a nice
/sys/class/infiniband/ehcaX/device symlink.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add "Modify Port" verb support to eHCA driver. The IB communication
manager needs this to set the IsCM port capability bit when
initializing.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There are quite a few places in ipoib_cm.c where we know IRQs are
enabled because we do something that sleeps in the same function, so
we can convert several occurrences of spin_lock_irqsave() to a plain
spin_lock_irq(). This cleans up the source a little and makes the
code smaller too:
add/remove: 0/0 grow/shrink: 1/5 up/down: 3/-51 (-48)
function old new delta
ipoib_cm_tx_reap 403 406 +3
ipoib_cm_stale_task 146 145 -1
ipoib_cm_dev_stop 173 172 -1
ipoib_cm_tx_handler 964 956 -8
ipoib_cm_rx_handler 956 937 -19
ipoib_cm_skb_reap 212 190 -22
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clarify code by changing return values from SMI functions to named
enum values instead of magic 0/1 values.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need to set the SGID index for routed MADs and pass received
GRH information to userspace when a MAD is received.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
To support destinations that are not on the local IB subnet, IPoIB
should include the GRH information when constructing an address
handle. Using the existing ib_init_ah_from_path() call will do this
for us.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
mthca_free_qp() already has local variables to hold the QP's send_cq
and recv_cq, so we can slightly clean up the calls to mthca_cq_clean()
by using those local variables instead of expressions like
to_mcq(qp->ibqp.send_cq).
Also, by cleaning the recv_cq first, we can avoid worrying about
whether the QP is attached to an SRQ for the second call, because we
would only clean send_cq if send_cq is not equal to recv_cq, and that
means send_cq cannot have any receive completions from the QP being
destroyed.
All this work even improves the generated code a bit:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-5 (-5)
function old new delta
mthca_free_qp 510 505 -5
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit b2875d4c ("IB/mthca: Always fill MTTs from CPU") causes a crash
in mthca_write_mtt() with non-memfree HCAs that have their memory
hidden (that is, have only two PCI BARs instead of having a third BAR
that allows access to the RAM attached to the HCA) on 64-bit
architectures. This is because the commit just before, c20e20ab
("IB/mthca: Merge MR and FMR space on 64-bit systems") makes
dev->mr_table.fmr_mtt_buddy equal to &dev->mr_table.mtt_buddy and
hence mthca_write_mtt() tries to write directly into the HCA's MTT
table. However, since that table is in the HCA's memory, this is
impossible without the PCI BAR that gives access to that memory.
This causes a crash because mthca_tavor_write_mtt_seg() basically
tries to dereference some offset of a NULL pointer. Fix this by
adding a test of MTHCA_FLAG_FMR in mthca_write_mtt() so that we always
use the WRITE_MTT firmware command rather than writing directly if
FMRs are not enabled.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The kernel ib_wc structure now uses a QP pointer, but the user space
equivalent uses a QP number instead. This means we can no longer use
a simple structure copy to copy stuff into user space.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't let userspace use the direct-physical-map L_key or R_key.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At some point things changed so that all the affinity bits can be set,
but cpus_full() macro is not true. This caused problems with the unit
selection logic on multi-unit (board) configurations.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the code that shuts down the IB link earlier in the unload
process, to be sure no new packets can arrive while we are unloading.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
To prevent random utility reads and writes of the diag interface to the
chip, we first require a handshake of reading from offset 0 and writing
to offset 0 before any other reads or writes can be done through the
diags device. Otherwise chip errors can be triggered.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the chip is no longer usable, LEDs should be turned off so system
can be found easily in the cluster.
Also some minor reorganizing so both chips print hardware error
message at same point and only if there were unrecovered errors
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Re-init of the kernel structures after a chip reset was leaving the
portdata structure for port zero in an inconsistent state, and a
pointer to it either stale (in re-init code) or NULL (in devdata)
Fixing the order of operations on this struct, and the condition for
interrupt access, prevents the crashes.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Due to a chip bug, the PIOAvail register is not always updated to
memory. This patch allows userspace to force an update.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In initialization, if we bailed at chip specific initialization, we
forgot to clean up the irq we had requested.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a bug where multicast packets without a GRH were not
being dropped as per the IB spec.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the module parameter "kpiobufs" is set too high, the calculation to
reset it to a sane value was incorrect.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix RDMA read response length checking for RDMA_READ_RESPONSE_ONLY to
allow a zero length response. RDMA read responses which don't match
the expected length or occur in response to some other operation
should generate a completion queue error (see table 56, ch. 9.9.2.3 in
the IB spec).
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Improve port-sharing performance by allowing any process to receive
packets from the shared hardware port under a spin lock for mutual
exclusion. Previously, one process was nominated as the master and
that process was responsible for receiving all packets from the shared
hardware port and either consuming them or forwarding them to their
destination. This led to starvation problems for other processes when
the master process was busy in computation phases.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The port sharing feature mixed kernel virtual addresses as well as
physical addresses for the offset used to describe the mmap address to
map the InfiniPath hardware into user space. This had a conflict on
powerpc. The new scheme converts it to a physical address so it
doesn't conflict with chip addresses and yet still fits in 40/44 bits
so it isn't truncated by 32-bit applications calling mmap64().
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a receive work request has been removed from the queue but has not
had a CQ entry generated for it and the QP is modified to the error
state, the completion entry generated is incorrect. This patch fixes
the problem.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Code was converted from a &= ~mask to clear_bit, but the bit was left
shifted instead of being used directly, so we were either trashing
memory several pages away, or sometimes taking a kernel page fault on
an invalid page.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some types of packet errors are moderately common with longer IB
cables and large clusters, and are not reported with prints by other
IB HCA drivers. This suppresses those messages unless the new
__IPATH_ERRPKTDBG bit is set in ipath_debug. Reporting of temporarily
disabled frequent error interrupts was also made clearer
We also distinguish between chip errors, and bad packets sent or
received in the wording of the messages.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a number of bugs with updating the PSN for retries of
RC requests.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When switching to the QP error state, the completion queue entries
(error or flush) were not being generated correctly.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath_dbg doesn't need the same prefixes that printk does.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds support for multiple RDMA reads and atomics to be sent
before an ACK is required to be seen by the requester.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a post send is done in loopback and there is no receive queue
entry, the sending QP is put on a timeout list for a while so the
receiver has a chance to post a receive buffer. If the another post
send is done, the code incorrectly tried to put the QP on the timeout
list again an corrupted the timeout list. This eventually leads to a
spin lock deadlock NMI due to the timer function looping forever with
the lock held.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A silly programming error causes a CQ entry to not be generated if a
SRQ limit event is generated.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A recent change was made to allocate memory for a port after CPU
affinity is set. That change didn't account for subports and was
trying to allocate memory for the port twice.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The chip documentation on the expected TID vs eager TID parity error
bits was reversed from what was implemented in the RTL, for both
chips. This corrects the definitions.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The loop which initializes the user memory region from an array of
pages was using the wrong limit for the array. This worked OK when
dma_map_sg() returned the same number as the number of pages. This
patch fixes the problem.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is a sticky state. It is useful for diagnosing problems with
boards versus cable/switch problems.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There's no point in printing the opcode field in the completion
handling debugging output, since the type of completion is already
printed at the beginning of the line. In fact the opcode field is not
even defined for completions with a status other than success.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current ib_umad code never accesses bits past IB_UMAD_MAX_PORTS in
dev_map[]. We shouldn't declare it to be twice as big.
Pointed-out-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
In mthca_arbel_fmr_unmap(), the high bits of the key are masked off.
This gets rid of the effect of adjust_key(), which makes sure that
bits 3 and 23 of the key are equal when the Sinai throughput
optimization is enabled, and so it may happen that an FMR will end up
with bits 3 and 23 in the key being different. This causes data
corruption, because when enabling the throughput optimization, the
driver promises the HCA firmware that bits 3 and 23 of all memory keys
will always be equal.
Fix by re-applying adjust_key() after masking the key.
Thanks to Or Gerlitz for reproducing the problem, and Ariel Shahar for
help in debug.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As of commit 6cdbd77e ("cxgb3 - missing CPL hanler and register
setting."), the cxgb3 ethernet NIC driver no longer handles SET_TCB
replies, so we need to do it in the iWARP driver.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Receive buffers need to be mapped with DMA_FROM_DEVICE. Incorrectly
mapping with DMA_TO_DEVICE causes a hard lock on ppc64 machines with
an IOMMU.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=431>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a connection is terminated asynchronously from the iSCSI layer's
perspective, iSER needs to notify the iSCSI layer that the connection
has failed. This is done using a workqueue (switched to from the iSER
tasklet context). Meanwhile, the connection object (that holds the
work struct) is released. If the workqueue function wasn't called
yet, it will be called later with a NULL pointer, which will crash the
kernel.
The context switch (tasklet to workqueue) is not required, and
everything can be done from the iSER tasklet. This eliminates the NULL
work struct bug (and simplifies the code).
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Handle aborting a command after it is sent
IB/mthca: Fix thinko in init_mr_table()
RDMA/cxgb3: Fix resource leak in cxio_hal_init_ctrl_qp()
The SCSI midlayer may abort a command that was already sent. If the
initiator is still trying to send the command (or data-out PDUs for
that command), the QP may time out after the midlayer times
out. Therefore, when aborting the command, iSER may still have
references for the command's buffers. When sending these PDUs, the
sends will complete with an error and their resources will be released
then.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit c20e20ab ("IB/mthca: Merge MR and FMR space on 64-bit systems")
swapped the number of MTTs and MPTs when initializing the MR table. As
a result, we get a kernel oops when the number of MTT segments
allocated exceeds 0x20000.
Noted by Troy Benjegerdes <troy@scl.ameslab.gov>, and reproduced by
Dotan Barak <dotanb@mellanox.co.il>. This fixes
https://bugs.openfabrics.org/show_bug.cgi?id=490
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This was spotted by the Coverity checker (CID 1554).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
->neigh_destructor() is killed (not used), replaced with
->neigh_cleanup(), which is called when neighbor entry goes to dead
state. At this point everything is still valid: neigh->dev,
neigh->parms etc.
The device should guarantee that dead neighbor entries (neigh->dead !=
0) do not get private part initialized, otherwise nobody will cleanup
it.
I think this is enough for ipoib which is the only user of this thing.
Initialization private part of neighbor entries happens in ipib
start_xmit routine, which is not reached when device is down. But it
would be better to add explicit test for neigh->dead in any case.
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet length checks in ipoib are broken: we add 4 bytes (IPoIB
encapsulation header) when sending a packet, not 20 bytes (hardware
address length) to each packet. Therefore, if connected mode is
enabled so that the interface MTU is larger than the multicast MTU,
IPoIB may end up trying to send too-long multicast packets. For
example, multicast is broken if a message of size 2048 bytes is sent
on an interface with UD MTU 2048, because 2048 is bigger than the real
limit of 2044 but the code tests against the wrong limit of 2060.
This patch fixes <https://bugs.openfabrics.org/show_bug.cgi?id=418>,
submitted by Scott Weitzenkamp <sweitzen@cisco.com>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The connected mode code added the possibility that an neigh struct
gets freed in the list_for_each_entry() loop in path_rec_completion(),
which causes a use-after-free. Fix this by changing to the _safe
variant of the list walking macro.
This was spotted by the Coverity checker (CID 1567).
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
eHCA scaling code must not depend on register_cpu_notifier() if
CONFIG_HOTPLUG_CPU is not set, so put all related code into #ifdefs.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There's a race between ipoib_mcast_leave() and ipoib_mcast_join_finish()
where we can try to detach from a multicast group before we've
attached to it. Fix this by reordering the code in ipoib_mcast_leave
to free the multicast group first, which waits for the multicast
callback thread (which calls ipoib_mcast_join_finish()) to complete
before detaching from the group.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The sense of the time_after_eq() test in ipoib_cm_stale_task() is
reversed so that only non-stale connections are reaped. Fix this by
changing to time_before_eq().
Noticed by Pradeep Satyanarayana <pradeep@us.ibm.com>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch renames DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH to avoid
confusion with the drivers default values (DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH
is the iscsi RFC specific default).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Do netif_carrier_on() right after the IPv4 broadcast multicast group
is joined, rather than waiting for all of the initial set of multicast
group joins to finish. This allows at least IPv4 traffic to limp
along on broken fabrics where not all multicast groups can be joined.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change the returned error code to ENOMEM if the connection event
backlog is full. This prevents the ib_cm from issuing a reject
on the connection, which can allow retries to succeed.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix memory region permission problems:
- remove useless and redundant iwch_mem_perms enum.
- create ib_to_tpt_access_rights() for mapping ib access rights
to T3 TPT permissions.
- create ib_to_mwbind_access_rights() for mapping ib access rights
to T3 MWBIND WR permissions.
- fix up the mem reg code to utilize the new functions.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Only print one AE error for a given connection in the kernel log.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Stop the endpoint timer when the MPA exchange is aborted by the peer.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change iwch_destroy_qp() to always move the QP to ERROR and let
iwch_modify_qp() decide what to do.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixes for "normal close" failures:
- Start normal close timer when moving to CLOSING state.
- Handle ABORTING state in close_con_rpl().
- Stop timer correctly on abort during a normal close.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cxgb3 uses dma_alloc_coherent() et al. thus needs linux/dma-mapping.h
include in order to build reliably.
Noticed on sparc64.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The struct rdma_bind_list fields for hlist are not being initialized,
resulting in a corrupted list. Fix this by using kzalloc() to make
sure all pointers are NULL.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the consumer rejects the connection we end up under-referencing the
endpoint structure. The fix is to call iwch_ep_disconnect() instead
of the low level disconnect functions so that the endpoint close timer
is started correctly.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The garbled logic in mthca_alloc_memfree() causes it to return 0, even
if it fails to allocate all doorbell records. Fix it to return -ENOMEM
when it fails.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes two issues reported by Roland Dreier and Christoph Hellwig:
- Mismatched sync/locking between completion handler and destroy cq We
introduced a counter nr_events per cq to track number of irq events
seen. This counter is incremented when an event queue entry is seen
and decremented after completion handler has been called regardless
if scaling code is active or not. Note that nr_callbacks tracks
number of events assigned to a cpu and both counters can potentially
diverge.
The sync between running completion handler and destroy cq is done
by using the global spin lock ehca_cq_idr_lock.
- Replace yield by wait_event on the counter above to become zero.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
An asynchronous event carries the port number that the event occurred
on, so there's no reason for an IPoIB interface to process an event
associated with a different local HCA port.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If path_rec_completion() is passed a non-NULL path record pointer
along with an unsuccessful status value, the tracing code incorrectly
prints the (invalid) DLID from the path record rather than the more
interesting status code. The actual logic of the function correctly
uses the path record only if the status indicates a successful lookup.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Stop the ep timer in ec_status() if the status indicates a
bad close.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- don't mark static functions in C files as inline - gcc should know
best whether inlining makes sense
- never compile the unused cxio_dbg.c
- make the following needlessly global functions static:
- cxio_hal.c: cxio_hal_clear_qp_ctx()
- iwch_provider.c: iwch_get_qp()
- remove the following unused global functions:
- cxio_hal.c: cxio_allocate_stag()
- cxio_resource.: cxio_hal_get_rhdl()
- cxio_resource.: cxio_hal_put_rhdl()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The cm_device references an ib_device, which already contains the node_guid.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The rdma_cm requires that path records be reversible. Set the
reversible bit when issuing an path record query.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hop_limit value in the ah_attr should be 0xFF, not the value read
from the received GRH (which should be 0). See 13.5.4.4 in the 1.2 IB
spec.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If no matching PD is found in ib_uverbs_reg_mr(), then the function
jumps to err_release without setting the return value ret. This means
that ret will hold the return value of the call to ib_umem_get() a few
lines earlier; if the function reaches the point where it looks for
the PD, we know that ib_umem_get() must have returned 0, so
ib_uverbs_reg_mr() ends up return 0 for a bad PD ID. Fix this by
setting ret to -EINVAL before jumping to the exit path when no PD is
found.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that low-level drivers handle the conversion from an absolute rate
to a relative rate, there's no need for the IPoIB driver to keep track
of the local port's data rate.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Avoid the overhead of freeing/reallocating and mapping/unmapping for
DMA pages that have not been written to by hardware.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes the needlessly global functions mthca_tavor_write_mtt_seg()
and mthca_arbel_write_mtt_seg() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
Correct mis-spellings of "algorithm", "appear", "consistent" and
(shame, shame) "kernel".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
The static rate from the path record should be put into the address
vector -- a long time ago the rate in the address attributes needed to
be a relative rate, which required more munging, but now that the
conversion from absolute to relative is done in the low-level driver,
it's easy for ib_init_ah_from_path() to put the absolute rate in.
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Extend rdma_cm to support multicast communication. Multicast support
is added to the existing RDMA_PS_UDP port space, as well as a new
RDMA_PS_IPOIB port space. The latter port space allows joining the
multicast groups used by IPoIB, which enables offloading IPoIB traffic
to a separate QP. The port space determines the signature used in the
MGID when joining the group. The newly added RDMA_PS_IPOIB also
allows for unicast operations, similar to RDMA_PS_UDP.
Supporting the RDMA_PS_IPOIB requires changing how UD QPs are initialized,
since we can no longer assume that the qkey is constant. This requires
saving the Q_Key to use when attaching to a device, so that it is
available when creating the QP. The Q_Key information is exported to
the user through the existing rdma_init_qp_attr() interface.
Multicast support is also exported to userspace through the rdma_ucm.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IB SA tracks multicast join/leave requests on a per port basis and
does not do any reference counting: if two users of the same port join
the same group, and one leaves that group, then the SA will remove the
port from the group even though there is one user who wants to stay a
member left. Therefore, in order to support multiple users of the
same multicast group from the same port, we need to perform reference
counting locally.
To do this, add an multicast submodule to ib_sa to perform reference
counting of multicast join/leave operations. Modify ib_ipoib (the
only in-kernel user of multicast) to use the new interface.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_cm_alloc_rx_skb() might be called from IRQ context, so it must
use dev_kfree_skb_any(), not kfree_skb().
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove the Open Grid Computing copyright. It shouldn't be there.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For T3B devices, mark user QP in error once we transition
to TERMINATE.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iwcm iw_cm_id destruction race condition fixes:
- iwcm_deref_id() always wakes up if there's another reference.
- clean up race condition in cm_work_handler().
- create static void free_cm_id() which deallocs the work entries and then
kfrees the cm_id memory. This reduces code replication.
- rem_ref() if this is the last reference -and- the IWCM owns freeing the
cm_id, then free it.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Acked-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the port phys state as returned from ehca_query_port() to LINK_UP.
ehca actually represents a logical HCA, whose phys/link state always
is LINK_UP.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allow users to en/disable scaling code when loading ib_ehca module,
rather than requiring the module to be rebuilt to change the setting.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a race condition in find_next_cpu_online() and some other locking
issues in ehca scaling code.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The change to allow allocating ICM chunks from coherent memory did not
increment the count of sg entries properly, so a chunk that required
more than allocation would not be mapped properly by the HCA.
Fix this by adding the missing increment of chunk->nsg.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
RESET->RESET is an allowed QP state transition, so mthca should handle
it correctly, by just returning success without involving the firmware.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mthca: Always fill MTTs from CPU
IB/mthca: Merge MR and FMR space on 64-bit systems
IB/mthca: Fix access to MTT and MPT tables on non-cache-coherent CPUs
IB/mthca: Give reserved MTTs a separate cache line
IB/mthca: Fix reserved MTTs calculation on mem-free HCAs
RDMA/cxgb3: Add driver for Chelsio T3 RNIC
IB: Remove redundant "_wq" from workqueue names
RDMA/cma: Increment port number after close to avoid re-use
IB/ehca: Fix memleak on module unloading
IB/mthca: Work around gcc bug on sparc64
IPoIB: Connected mode experimental support
IB/core: Use ARRAY_SIZE macro for mandatory_table
IB/mthca: Use correct structure size in call to memset()
Speed up memory registration by filling in MTTs directly when the CPU
can write directly to the whole table (all mem-free cards, and to
Tavor mode on 64-bit systems with the patch I posted earlier). This
reduces the number of FW commands needed to register an MR by at least
a factor of 2 and speeds up memory registration significantly.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For Tavor, we currently reserve separate MPT and MTT space for FMRs to
avoid abusing the vmalloc space on 32 bit kernels. No such problem
exists on 64 bit kernels so let's not do it there.
This way we have a shared pool for MR and FMR resources, used on
demand. This will also make it possible to write MTTs for regular
regions directly from driver.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We allocate the MTT table with alloc_pages() and then do pci_map_sg(),
so we must call pci_dma_sync_sg() after the CPU writes to the MTT
table. This works since the device will never write MTTs on mem-free
HCAs, once we get rid of the use of the WRITE_MTT firmware command.
This change is needed to make that work, and is an improvement for
now, since it gives FMRs a chance at working.
For MPTs, both the device and CPU might write there, so we must
allocate DMA coherent memory for these.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
MTTs are allocated in non-cache-coherent memory, so we must give
reserved MTTs their own cache line, to prevent both device and
CPU from writing into the same cache line at the same time.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The reserved_mtts field has different meaning in Tavor and Arbel, so
we are wasting mtt entries on memfree. Fix the Arbel case to match
Tavor semantics.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an RDMA/iWARP driver for the Chelsio T3 1GbE and 10GbE adapters.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace appropriate pairs of "kmem_cache_alloc()" + "memset(0)" with the
corresponding "kmem_cache_zalloc()" call.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Roland McGrath <roland@redhat.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randomize the starting port number and avoid re-using port values
immediately after they are closed. Instead keep track of the last
port value used and increment it every time a new port number is
assigned, to better replicate other port spaces.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Percpu data is not freed on module unloading.
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For some reason gcc-3.4.5 on sparc64 does:
WARNING: "____ilog2_NaN" [drivers/infiniband/hw/mthca/ib_mthca.ko] undefined!
Points to note:
(1) The asm volatile flush/flushw are just markers for viewing what comes out
in the assembly; removing them has no effect on the result.
(2) Changing almost anything else in dwh__mthca_arbel_init_srq_context() or
dwh__mthca_alloc_srq() causes the problem to go away.
The compiler command line issued by the kernel build is:
/opt/crosstool/gcc-3.4.5-glibc-2.3.6/sparc64-unknown-linux-gnu/bin/sparc64-unknown-linux-gnu-gcc -fno-strict-aliasing -fno-common -Os -m64 -mno-fpu -mcpu=ultrasparc -mcmodel=medlow -ffixed-g4 -ffixed-g5 -fcall-used-g7 -Wa,--undeclared-regs -pg -fno-omit-frame-pointer -fno-optimize-sibling-calls -fasynchronous-unwind-tables -g -c -o drivers/infiniband/hw/mthca/.tmp_mthca_srq.o drivers/infiniband/hw/mthca/mthca_srq.c
This can be reduced to this whilst still retaining the problem:
/opt/crosstool/gcc-3.4.5-glibc-2.3.6/sparc64-unknown-linux-gnu/bin/sparc64-unknown-linux-gnu-gcc -m64 -c -o drivers/infiniband/hw/mthca/mthca_srq.o drivers/infiniband/hw/mthca/mthca_srq.c -Os
Removing -Os or changing it to -O or -O0 thru -O6 gets rid of the problem.
This patch to the kernel code fixes the problem:
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The following patch adds experimental support for IPoIB connected
mode, as defined by the draft from the IETF ipoib working group. The
idea is to increase performance by increasing the MTU from the maximum
of 2K (theoretically 4K) supported by IPoIB on top of UD. With this
code, I'm able to get 800MByte/sec or more with netperf without
options on a Mellanox 4x back-to-back DDR system.
Some notes on code:
1. SRQ is used for scalability to large cluster sizes
2. Only RC connections are used (UC does not support SRQ now)
3. Retry count is set to 0 since spec draft warns against retries
4. Each connection is used for data transfers in only 1 direction, so
each connection is either active(TX) or passive (RX). 2 sides that
want to communicate create 2 connections.
5. Each active (TX) connection has a separate CQ for send completions -
this keeps the code simple without CQ resize and other tricks
6. To detect stale passive side connections (where the remote side is
down), we keep an LRU list of passive connections (updated once per
second per connection) and destroy a connection after it has been
unused for several seconds. The LRU rule makes it possible to avoid
scanning connections that have recently been active.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use ARRAY_SIZE() macro already defined in kernel.h instead of open
coding equivalent code.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When clearing the ib_ah_attr parameter in to_ib_ah_attr(), use sizeof
*ib_ah_attr instead of sizeof *path.
Pointed out by Jack Morgenstein <jackm@mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This lets the network core have the ability to handle suspend/resume
issues, if it wants to.
Thanks to Frederik Deweerdt <frederik.deweerdt@gmail.com> for the arm
driver fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove prototypes for functions that don't exist.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch removes do_mmap() from ehca:
- Call remap_pfn_range() for hardware register block
- Use vm_insert_page() to register memory allocated for completion
queues and queue pairs
- The actual mmap() call/trigger is now controlled by user space,
ie. libehca
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The iWARP connection manager uses the ib_addr services to do route
resolution (neighbour discovery in the IP world). The ib_addr
netevent callback routine, however, currently only acts on InfiniBand
neighbour updates. It needs to act on ethernet neighbour updates as
well.
This patch just removes filtering on device type altogether and will
trigger on any neighour updates where the nud_type is valid. This
simplifies the code some.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When there is a call to send_tsk_mgmt SRP posts a send and waits for 5
seconds to get a response.
When the QP is in the error state it is obvious that there will be no
response so it is quite useless to wait. In fact, the timeout causes
SRP to wait a long time to reconnect when a QP error occurs. (Each
abort and each reset_device calls send_tsk_mgmt, which waits for the
timeout). The following patch solves this problem by identifying the
failure and returning an immediate error code.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
struct ib_wc currently only includes the local QP number: this matches
the IB spec, but seems mostly useless. The following patch replaces
this with the pointer to qp itself, and updates all low level drivers
and all users.
This has the following advantages:
- Ability to get a per-qp context through wc->qp->qp_context
- Existing drivers already have the qp pointer ready in poll cq, so
this change actually saves a tiny bit (extra memory read) on data path
(for ehca it would actually be expensive to find the QP pointer when
polling a CQ, but ehca does not support SRQ so we can leave wc->qp as
NULL for ehca)
- Users that need the QP number can still get it through wc->qp->qp_num
Use case:
In IPoIB connected mode code, I have a common CQ shared by multiple
QPs. To track connection usage, I need a way to get at some per-QP
context upon the completion, and I would like to avoid allocating
context object per work request just to stick a QP pointer into it.
With this code, I can just use wc->qp->qp_context.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The lock is taken with _irqsave and hence must be released with
_irqrestore on all paths.
Signed-off-by Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Checks if the kmalloc in match_strdup() was successful, and bail out
on looking at the token if it failed.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a QP being queried is in the RESET state, don't execute the
QUERY_QP firmware command (because it will fail).
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Here is a patch for ehca to use proper flag, ie. GFP_ATOMIC
resp. GFP_KERNEL, when calling get_zeroed_page() to prevent "Bug:
scheduling while atomic...". This error does not cause a kernel panic
but makes ipoib un-usable afterwards. It is reproducible on
2.6.20-rc4 if one does ifconfig down during a flood ping test. I have
not observed this error in earlier releases incl. 2.6.20-rc1.
This error occurs when a qp event/irq is received and ehca event
handler allocates a control block/page to obtain HCA error data block.
Use of GFP_ATOMIC when in interrupt context prevents this issue.
Signed-off-by Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to the Tavor and Arbel programmer's reference manuals, the
number of bytes transferred is not provided in the byte_cnt field of
the CQ entry for atomic operation completions. For atomic operations,
the number of bytes transferred is always 8 (when the status is
"success"), and this constant value should always be used by the
driver in the ib_wc entry returned, rather than using the CQE.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There's a problem with how rdma cm events are reported to userspace
that can lead to application crashes.
When a new connection request arrives, a context for the connection is
allocated in the kernel. The connection event is then reported to
userspace. The userspace library retrieves the event and allocates
its own context for the connection. The userspace context is
associated with the kernel's context when accepting. This allows the
kernel to give userspace context with other events.
A problem occurs if a second event for the same connection occurs
before the user has had a chance to call accept. The userspace
context has not yet been set, which causes the librdmacm to crash.
(This has been seen when the app takes too long to call accept,
resulting in the remote side timing out and rejecting the connection)
Fix this by ignoring events for new connections until userspace has
set their context. This can only happen if an error occurs on a new
connection before the user accepts it. This is okay, since the accept
will just fail later.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We discard new connection requests while the listen backlog is full,
but leak a struct ucma_event in the process. Free the structure in
this case.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The iWARP CM should report timeouts as event RDMA_CM_EVENT_UNREACHABLE,
not event RDMA_CM_EVENT_REJECTED.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iSER limits the number of outstanding PDUs to send. When this threshold
is reached, it should return an error code (-ENOBUFS) instead of setting
the suspend_tx bit (which should be used only by libiscsi).
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_table_find() will return the wrong address when the table entry
being searched for is exactly at the beginning of a sglist entry
(other than the first), because it uses >= when it should use >.
Example: assume we have 2 entries in scatterlist, 4K each, offset is
4K. The current code will return first entry + 4K when we really want
the second entry.
In particular this means mapping an FMR on a memfree HCA may end up
writing the page table into the wrong place, leading to memory
corruption and also causing the HCA to use an incorrect address
translation table.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit bed8bdfd ("IB: kmemdup() cleanup") introduced one bad conversion to
kmemdup() in mthca_alloc_fmr(), where the structure allocated and the
structure copied are not the same size. Revert this back to the original
kmalloc()/memcpy() code.
Reported-by: Dotan Barak <dotanb@mellanox.co.il>.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mthca_device_mutex() can be initialized automatically with
DEFINE_MUTEX() rather than explicitly calling mutex_init(). This
saves a bit of text and shrinks the source by a line, so we may as
well do it....
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add module parameters that enable settting some of the HCA
profile values, such as the number of QPs, CQs, etc.
Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
struct srp_device.fmr_page_mask was unsigned long, which means that
the top part of addresses above 4G was being chopped off on 32-bit
architectures. Of course nothing good happens when data from SRP
targets is DMAed to the wrong place.
Fix this by changing fmr_page_mask to u64, to match the addresses
actually used by IB devices.
Thanks to Brian Cain <Brian.Cain@ge.com> and David McMillen
<davem@systemfabricworks.com> for help diagnosing the bug and testing
the fix.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the initialization of ipoib_neigh's skb_queue into
ipoib_neigh_alloc(), since commit 2745b5b7 ("IPoIB: Fix skb leak when
freeing neighbour") will make iterate over the skb_queue to free any
packets left over when freeing the ipoib_neigh structure.
This fixes a crash when freeing ipoib_neigh structures allocated in
ipoib_mcast_send(), which otherwise don't have their skb_queue
initialized.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert iSER to use the new verbs DMA mapping functions for kernel
verbs consumers.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert SRP to use the new verbs DMA mapping functions for kernel
verbs consumers.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert IPoIB to use the new DMA mapping functions
for kernel verbs consumers.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert code in core/ to use the new DMA mapping functions for kernel
verbs consumers.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch implements the interposing DMA mapping functions to allow
support for IOMMUs and remove the dependence on phys_to_virt() and
bus_to_virt().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Export the rdma cm interfaces to userspace via a misc device.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allow the use of UD QPs through the rdma_cm, in order to provide
address translation services for resolving IB addresses for datagram
messages using SIDR.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During connection establishment, the passive side of a connection can
receive messages from the active side before the connection event has
been delivered to the user. Allow the passive side to send messages
in response to received data before the event is delivered. To handle
the case where the connection messages are lost, a new rdma_notify()
function is added that users may invoke to force a connection into the
established state.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Connection information was never given to the recipient of a
connection request or reply message. Only the event was delivered.
Report the connection data with the event to allows user to
reject the connection based on the requested parameters, or adjust
their resources to match the request.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The qp_type parameter into the rdma_cm is unneeded, and can be
misleading. The QP type should be determined from the port space.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 51f65ebc ("IB/ipath - program intconfig register using new HT
irq hook"), which fixed interrupts for HyperTransport HCAs, broke PCI
Express HCAs, because for those HCAs, the driver uses the value of
pdev->irq before pci_enable_msi() and ends up getting a totally bogus
IRQ number. Fix this by using the value of pdev->irq after
pci_enable_msi().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove variables that are set but then never looked at in the iSER
initiator. These cleanups came from David Binderman's list of "set
but never used" warnings from icc.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove variables that are set but then never looked at in the ipath
driver. These cleanups came from David Binderman's list of "set but
never used" warnings from icc.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_flush_fmr_pool() stashes away the request generation number
properly, but then goes ahead and rereads it every time it tests
whether the flush generation number has caught up. This means that
there is a theoretical possibility of livelock, if the request
generation number keeps getting bumped and the flush generation number
never catches up. The fix is simple: use the request generation
number read at the beginning of the function.
Also, atomic_inc() followed by atomic_read() can be replaced with
atomic_int_return(). There's no real requirement for atomicity here
but we might as well shrink the code.
This bug was discovered using David Binderman's list of "set but never
used" warnings from icc.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
ib_ucm_cleanup_events() holds file_mutex while calling ib_destroy_cm_id().
This can deadlock since ib_destroy_cm_id() flushes event handlers, and
ib_ucm_event_handler() needs file_mutex, too. Therefore, drop the
file_mutex during the call to ib_destroy_cm_id().
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ib_cm_establish() function is replaced with a more generic
ib_cm_notify(). This routine is used to notify the CM that failover
has occurred, so that future CM messages (LAP, DREQ) reach the remote
CM. (Currently, we continue to use the original path) This bumps the
userspace CM ABI.
New alternate path information is captured when a LAP message is sent
or received. This allows QP attributes to be initialized for the user
when a new path is loaded after failover occurs.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_neigh_free() is sometimes called while neighbour is still alive,
so it might still have queued skbs. Fix skb leak in this case.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SRP reallocates the IU buffers for tx_ring and rx_ring without freeing
the old buffers when it reconnects to a target. Fix this by keeping
the old IU buffers around.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix following problems in process_req() relating to cancellation:
- Function is wrongly doing another addr_remote() when cancelled,
which is not required.
- Make failure reporting immediate by using time_after_eq().
- On cancellation, -ETIMEDOUT was returned to the callback routine
instead of the more appropriate -ECANCELLED (users getting notified
may want to print/return this status, eg ucma_event_handler).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It is possible to swap the CQs used for send_cq and recv_cq when
creating two different QPs. If these two QPs are then destroyed at
the same time, an AB-BA deadlock can occur because the CQ locks are
taken our of order. Fix this by always taking CQ locks in a fixed
order.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When initializing an mthca SRQ, the log_srq_size field should be the
log of the number of SRQ WQEs, not the log of the number of bytes in
the SRQ.
This affects only mthca drivers for memfree HCAs which set the initial
srq wqe counter (in the SW2HW transition) to a non-zero value.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is a patch for ehca to fix a bug in prepare_sqe_to_rts(), which
used WQE address to iterate pending work requests. This might cause
an access violation since the queue pages can not be assumed to follow
each other consecutively. Thus, this patch introduces a few queue
functions to determine WQE offset based on its address and uses WQE
offset to iterate the pending work requests.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In iwcm_deref_id(), the comment says : "If the last reference is being
removed and iw_destroy_cm_id is waiting, wake up the waiting
thread". The second part of the comment, "and iw_destroy_cm_id is
waiting," is wrong, since this function either wakes the waiter
already waiting in iwcm_deref_id, or enables it (so that when
wait_for_completion() is performed later, it will immediately return).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove unnecessary cm_id_priv argument to copy_private_data(), and
change text to reflect the code. Fix couple of typos in comments.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If we get IW_CM_EVENT_CONNECT_REQUEST message and encounter an error
(not in the LISTEN state, cannot create an id, cannot alloc
work_entry, etc), then the memory allocated by cm_event_handler() in
the event->private_data gets leaked. Since cm_work_handler has already
put the event on the work_free_list, this allocated memory is
leaked. High backlog value can allow DoS attacks.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Possible memory corruption scenario: after putting the work entry back
on the work_free_list, we call process_event() which dereferences
work->event, which could have been modified to another value
meanwhile.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The amso1100 driver was missing a couple of __devinit/__devexit
annotations for init/cleanup functions that are called from
__devinit/__devexit functions.
Reported by Randy Dunlap <randy.dunlap@oracle.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit b3b30f5e ("IB/mthca: Recover from catastrophic errors")
introduced some section mismatch breakage, because the error recovery
code tears down and reinitializes the device, which calls into lots of
code originally marked __devinit and __devexit from regular .text.
Fix this by getting rid of these now-incorrect section markers.
Reported by Randy Dunlap <randy.dunlap@oracle.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the Scsi_Host's max_cmd_len from 12 (default) to 16 for
SRP. Otherwise scsi_dispatch_cmd() won't pass down certain commands
such as READ CAPACITY 16, required for supporting disks > 2TB.
Signed-off-by: Arne Redlich <arne.redlich@xiranet.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The qp_access_flags are for remote access permissions only, so
IB_ACCESS_LOCAL_WRITE is an invalid value. Remove it from the values
set by cm_init_qp_init_attr() and cma_init_ib_qp().
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace open coded kmemdup() to save some screen space, and allow
inlining/not inlining to be triggered by gcc.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rewrite cma_req_handler error handling case to encapsulate
common code.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In queue_req(), use time_after_eq() instead of time_after()
for following reasons :
- Improves insert time if multiple entries with same time are
present.
- set_timeout need not be called if entry with same time
is added to the list (and that happens to be the entry
with the smallest time), saving atomic/locking operations.
- Earlier entries with same time are deleted first (fifo).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove redundant check of node_guid in cma_add_one().
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Optimize to test for an empty list first. This ends up simplifying
the code too.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath uses skb functions and won't build without CONFIG_NET.
Spotted by Randy Dunlap.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IPoIB assumes that high (reserved) octet in the hardware address is 0,
and copies it into the QPN. This violates RFC 4391 (which requires
that the high 8 bits are ignored on receive), and will result in an
invalid QPN being used when interoperating with IPoIB connected mode.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PCI Express and Hypertransport chip-specific source files should only
be built when the kernel has the capability of actually compiling them.
This fixes the driver build on, for example, ia64.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mad: Fix race between cancel and receive completion
RDMA/amso1100: Fix && typo
RDMA/amso1100: Fix unitialized pseudo_netdev accessed in c2_register_device
IB/ehca: Activate scaling code by default
IB/ehca: Use named constant for max mtu
IB/ehca: Assure 4K alignment for firmware control blocks
When ib_cancel_mad() is called, it puts the canceled send on a list
and schedules a "flushed" callback from process context. However,
this leaves a window where a receive completion could be processed
before the send is fully flushed.
This is fine, except that ib_find_send_mad() will find the MAD and
return it to the receive processing, which results in the sender
getting both a successful receive and a "flushed" send completion for
the same request. Understandably, this confuses the sender, which is
expecting only one of these two callbacks, and leads to grief such as
a use-after-free in IPoIB.
Fix this by changing ib_find_send_mad() to return a send struct only
if the status is still successful (and not "flushed"). The search of
the send_list already had this check, so this patch just adds the same
check to the search of the wait_list.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the AMSO1100 firmware version computation, which was broken
due to "&&" being used where "&" should have.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rework some load-time error handling: c2_register_device() leaked when
it failed, and the function that called it didn't check the return code.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change ehca's Kconfig to activates scaling code as default. After
several measurements we saw that this feature prevents dropped packets
(UD) in stress situation. Thus, enabling it helps to improve ehca's
bandwidth through IPoIB.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Define and use a constant EHCA_MAX_MTU instead hardcoded value.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Assure 4K alignment for firmware control blocks in 64K page mode,
because kzalloc()'s result address might not be 4K aligned if 64K
pages are enabled. Thus, we introduce wrappers called
ehca_{alloc,free}_fw_ctrlblock(), which use a slab cache for objects
with 4K length and 4K alignment in order to alloc/free firmware
control blocks in 64K page mode. In 4K page mode those wrappers just
are defines of get_zeroed_page() and free_page().
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eric's changes to the htirq infrastructure require corresponding
modifications to the ipath HT driver code so that interrupts are still
delivered properly.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Require registration with ib_addr module to prevent caller from
unloading while a callback is in progress.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Several fields in an incoming MAD extended info header were passed
into the MAD_IFC firmware command at incorrect offsets (mostly off by
4 bytes). As the result, the HCA will fail to generate traps in which
this info is needed (e.g. traps which include the GRH of the incoming
packet), in violation of the IB spec.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Return the sq_draining value back to user space for query_qp instead
of the en_sqd_async notify value, which is valid only for
modify_qp. For query_qp, the draining status should returned.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The Ammasso driver needs to use dma_alloc_coherent() for
allocating memory that will be used by the HW for dma.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The eHCA driver does not compile for a uniprocessor configuration
(CONFIG_SMP=n), due to H_SUCCESS and other symbols being undefined.
This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Hoang-Nam Nguyen <HNGUYEN@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
