In addition to mlx4_ib, there will be ethernet and FC consumers of
mlx4_core, so move the code for managing kernel doorbells into the
core module to avoid having to duplicate this multiple times.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Always enable large page support; didn't seem to cause problems for anyone.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch enables IPoIB to use 4K UD messages (when the underlying
device and fabrics support a 4K MTU) by using two scatter buffers when
PAGE_SIZE is less than or equal to thhe HCA IB MTU size. The first
buffer is for IPoIB header + GRH header, and the second buffer is the
IPoIB payload, which is 4K-4.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After PXE boot, the iw_nes driver does a full reset to ensure the card
is in a clean state. However, it doesn't wait for firmware to
complete its work before issuing a port reset to enable the ports,
which leads to problems bringing up the ports.
The solution is to wait for firmware to complete its work before
proceeding with port reset.
This bug was flagged by Roland Dreier <rolandd@cisco.com>.
Cc: <stable@kernel.org>
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use NIPQUAD_FMT instead of printing raw 32-bit hex quantities in
debugging output.
Acked-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PCI MSI interface is stubbed out properly so that all the
functions just return failure if PCI_MSI=n, so there's no reason to
have "#ifdef CONFIG_PCI_MSI" blocks in ipath_iba7220.c.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Before IBA7220 support was added, the ipath driver didn't support any
hardware unless PCI_MSI and/or HT_IRQ was enabled. However, the
IBA7220 can generate INTx interrupts, so it makes sense to allow the
driver to be build even if PCI_MSI=n and HT_IRQ=n.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The new IBA7220 code added a call to ipath_init_iba7220_funcs() that
is compiled unconditionally, but only built the IBA7220 code if
PCI_MSI is enabled. Fix this by building the IBA7220 file
unconditonally.
This fixes build breakage when PCI_MSI=n, HT_IRQ=y and
INFINIBAND_IPATH=y reported by Ingo Molnar <mingo@elte.hu>:
drivers/built-in.o: In function `ipath_init_one':
ipath_driver.c:(.devinit.text+0x1e5bc): undefined reference to `ipath_init_iba7220_funcs'
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 124b4dcb ("IB/ipath: add calls to new 7220 code and enable in
build") inadvertently added core to set dev->class_dev.dev back into
ib_ipath. This is completely redundant since commit 1912ffbb ("IB: Set
class_dev->dev in core for nice device symlink"), which removed
class_dev setting from low-level drivers, and also will break the build
when class_dev is removed completely from struct ib_device.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Describe disable_sma parameter with its name rather than the internal
ib_ipath_disable_sma variable name, so that the description shows up
properly in modinfo.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove redundant static declarations of functions that are defined
before they are used in the source.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This sets us up to be able to convert the srp_host to use a struct
device instead of a class_device.
Based on a original patch from Tony Jones, but split up into this piece
by Greg.
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Reviewed-by: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the main ib_device to use struct device instead of struct
class_device as class_device is going away.
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
The itt field in struct iscsi_data is not defined with any particular
endianness. open-iscsi should use it as-is without byte-swapping it.
This fixes sparse warnings coming from doing ntohl(hdr->itt).
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The mlx4_ib driver is stable enough for production use, so bump the
version number to 1.0 to indicate this.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a P_Key is deleted and then re-added at the same index, then IPoIB
gets confused because __ipoib_ib_dev_flush() only checks whether the
index is the same without checking whether the P_Key was present, so
the interface is stopped when the P_Key is deleted, but the event when
the P_Key is re-added gets ignored and the interface never gets
restarted.
Also, switch to using ib_find_pkey() instead of ib_find_cached_pkey()
everywhere in IPoIB, since none of the places that look for P_Keys are
in a fast path or in non-sleeping context, and in general we want to
kill off the whole caching infrastructure eventually. This also fixes
consistency problems caused because some IPoIB queries were cached and
some were uncached during the window where the cache was not updated.
Thanks to Venkata Subramonyam <vsubramo@cisco.com> for debugging this
problem and testing this fix.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a RDMA_CM_EVENT_DEVICE_REMOVAL event is raised, iSER should
release the connection resources.
This is necessary when the IB HCA module is unloaded while open-iscsi
is still running. Currently, iSER just BUG()s.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Also, introduce a few inline helper functions to make the code more readable.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the free_irq() call in nes_remove() to before the tasklet_kill();
otherwise there is a window after tasklet_kill() where a new interrupt
can be handled and reschedule the tasklet, leading to a use-after-free
crash.
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ib_mthca driver has been stable for a while, so bump the version
number to 1.0 to indicate this.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the QP was moved to another state (such as SQE) by the hardware,
then after this change the user won't have to set the IBV_QP_CUR_STATE
mask in order to execute modify QP in order to recover from this state.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the QP was moved to another state (such as SQE) by the hardware,
then after this change the user won't have to set the IBV_QP_CUR_STATE
mask in order to execute modify QP in order to recover from this state.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a place where we might dereference a NULL pointer; this fixes
Coverity CID 1392. On inspection I also found a place where we could
attempt to kmem_cache_free() a NULL pointer, so fix this too.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This can be used to tune at run time the parameters controlling the
event (interrupt) generation rate and thus reduce the overhead
incurred by handling interrupts resulting in better throughput. Since
IPoIB uses a single CQ for both RX and TX, RX is chosen to dictate
configuration for both RX and TX.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for modifying CQ parameters for controlling event
generation moderation.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Just add the infrastructure so we can add functionality later.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Handle IB_WR_SEND_WITH_INV work requests.
This resurrects a patch sent long ago by Mikkel Hagen <mhagen@iol.unh.edu>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a new IB_WR_SEND_WITH_INV send opcode that can be used to mark a
"send with invalidate" work request as defined in the iWARP verbs and
the InfiniBand base memory management extensions. Also put "imm_data"
and a new "invalidate_rkey" member in a new "ex" union in struct
ib_send_wr. The invalidate_rkey member can be used to pass in an
R_Key/STag to be invalidated. Add this new union to struct
ib_uverbs_send_wr. Add code to copy the invalidate_rkey field in
ib_uverbs_post_send().
Fix up low-level drivers to deal with the change to struct ib_send_wr,
and just remove the imm_data initialization from net/sunrpc/xprtrdma/,
since that code never does any send with immediate operations.
Also, move the existing IB_DEVICE_SEND_W_INV flag to a new bit, since
the iWARP drivers currently in the tree set the bit. The amso1100
driver at least will silently fail to honor the IB_SEND_INVALIDATE bit
if passed in as part of userspace send requests (since it does not
implement kernel bypass work request queueing). Remove the flag from
all existing drivers that set it until we know which ones are OK.
The values chosen for the new flag is not consecutive to avoid clashing
with flags defined in the XRC patches, which are not merged yet but
which are already in use and are likely to be merged soon.
This resurrects a patch sent long ago by Mikkel Hagen <mhagen@iol.unh.edu>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds the initialization calls into the new 7220 HCA files,
changes the Makefile to compile and link the new files, and code to
handle send DMA.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The patch adds a number of minor changes to support newer HCAs:
- New send buffer control bits
- New error condition bits
- Locking and initialization changes
- More send buffers
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A new file which allows the IBA7220 send DMA engine to be used from
userland. The routines here are not linked in yet, that will happen in
a follow-on patch...
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A new header file which allows the IBA7220 send DMA engine to be used
from userland. The definitions here are not used yet, that will happen
in a follow-on patch...
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IBA7220 HCA has a new feature to DMA data to the on chip send
buffers instead of or in addition to the host CPU doing the data
transfer. This patch adds code to support the send DMA queue.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds binary data to initialize the IB SERDES.
Signed-off-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The control and initialization of the SerDes blocks of the IBA7220 is
sufficiently complex to merit a separate file.
Signed-off-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds the HCA-specific code for the IBA7220 HCA.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds a new ASIC-specific header file for the HCAs using the IBA7220.
Signed-off-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is part of a patch series to add support for a new HCA. This patch
adds new fields to the header files.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes chip reset more robust and reduces lock contention
between user and kernel TID register updates.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Newer HCAs support MSI interrupts and also INTx interrupts. Fix the
code so that INTx can be reliably enabled if MSI interrupts are not
working.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Newer HCAs have a threshold counter to reduce the number of DMAs the
chip makes to update the PIO buffer availability status bits. This
patch enables the feature.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Whenever the LID is set, notify the HCA specific code so that the
appropriate HW registers can be updated. Also log the info on the
console at low priority.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds code to enable/disable the IBTA 1.2 heartbeat for testing
if the HCA supports it.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hardware-based recovery doesn't need any intervention, and in a few
cases we can get a bit confused about state and skip steps such as
turning off the link state LED when we consider recovery to be "down".
So ignore this transition, and either we recover in hardware, or we
transition to down, and will handle it then.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Newer HCAs have a HW option to write a sequence number to each receive
queue entry and avoid a separate DMA of the tail register to memory.
This patch adds support for these changes.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes some white space changes and minor non-functional
changes to more closely match the code in OFED-1.3.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch checks for old and new format writes to send a packet via the
diagnostic interface.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make sure that a device implements the modify_srq and reg_phys_mr
optional methods before calling them.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Raw comparison against jiffies will fail if jiffies wraps, although
since ipath currently only supports 64-bit architectures, this is rather
far-fetched. Still, it's better to use time_after_eq().
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rather than have build_mlx_header() return a negative value on failure
and the length of the segments it builds on success, add a pointer
parameter to return the length and return 0 on success. This matches
the calling convention used for build_lso_seg() and generates slightly
smaller code -- eg, on 64-bit x86:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-22 (-22)
function old new delta
mlx4_ib_post_send 2023 2001 -22
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For HCAs that support TCP segmentation offload (IB_DEVICE_UD_TSO), set
NETIF_F_TSO and use HW LSO to offload TCP segmentation.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a create_flags member to struct ib_qp_init_attr that will allow a
kernel verbs consumer to create a pass special flags when creating a QP.
Add a flag value for telling low-level drivers that a QP will be used
for IPoIB UD LSO. The create_flags member will also be useful for XRC
and ehca low-latency QP support.
Since no create_flags handling is implemented yet, add code to all
low-level drivers to return -EINVAL if create_flags is non-zero.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for reading newer card's EEPROMs while continuing to support
older EEPROMs.
Also, add support for the temperature sensor if present.
Signed-off-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This reduces the latency for RC ACKs when a PIO buffer is available.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A fixed partitioning of send buffers is determined at driver load time
for user processes and kernel use. Since send buffers are a scarce
resource, it makes sense to allow the kernel to use the buffers if they
are not in use by a user process.
Also, eliminate code duplication for ipath_force_pio_avail_update().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The link can be put in LINKDOWN_DISABLE state either locally or via a
MAD. However, the link-recovery code will take it out of that state as
a side-effect of attempts to clear SerDes/XGXS issues.
We add a flag to indicate "link is down on purpose, leave it alone."
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Update the module author to the current email address.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In list iteration code, you normally wouldn't be calling
"container_of()" directly anyway, you'd be invoking "list_entry()".
But you don't even need that here, "list_for_each_entry()" is fine.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert list_splice() + INIT_LIST_HEAD() to the equivalent list_splice_init()
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The function rdma_create_id() always returns either a valid pointer or
a value made with ERR_PTR, so its result should be tested with IS_ERR,
not with a test for 0.
The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
//<smpl>
@a@
expression E, E1;
statement S,S1;
position p;
@@
E = rdma_create_id(...)
... when != E = E1
if@p (E) S else S1
@n@
position a.p;
expression E,E1;
statement S,S1;
@@
E = NULL
... when != E = E1
if@p (E) S else S1
@depends on !n@
expression E;
statement S,S1;
position a.p;
@@
* if@p (E)
S else S1
//</smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The session_id members of struct nes_cm_listener and struct
nes_cm_node are write-only, so remove them. This allows the
session_id member of struct nes_cm_core to be removed as well, since
it is only used to write those other session_id values.
This removes the use of current->tgid (which will be deprecated)
pointed out by Pavel Emelyanov <xemul@openvz.org>.
Acked-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In slave_or_pri_blk(), pci_write_config_byte() is used to write a
16-bit quantity to clear linkctrl CRC error bits. This is clearly a
bug and also causes the warning
drivers/infiniband/hw/ipath/ipath_iba6110.c: In function 'slave_or_pri_blk':
drivers/infiniband/hw/ipath/ipath_iba6110.c:849: warning: overflow in implicit constant conversion
Fix this by using pci_write_config_word() instead.
Acked-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The receive queue number of WRs and SGEs shouldn't be checked if a
SRQ is specified.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove useless comment about list removal since locks are held and
the code checks that the QP is on the list before removing it.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Workaround a QLE7140 problem that in rare cases causes flow control
problems after link recovery by forcing a link retrain after recovery.
A module parameter is provided to control the behavior in case it causes
problems.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds code to get/set portinfo to support multiple link speeds
and widths.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There's a conflict between our need to quiesce PSM-based applications
to avoid HoL blocking when the IB link goes down and the apps' desire
to remain running so that their quiescence timout mechanism can keep
running.
The compromise is to STOP the processes for a fixed period of time and
then alternate between CONT and STOP until the link is again active.
If there are poor interactions with subnet manager configuration at a
given site, the interval can be adjusted via a module paramter.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't try to handle freeze mode HW errors if the driver is in diagnostic
mode since some tests can cause errors that shouldn't be processed.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The check for link up was incorrect, thus setting the LED display
inconsistently with the link state.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error recovery code for updating the driver's cached status information
for which send buffers are busy or free wasn't updated for IBA7220.
It should be similar to the initialization code in enable_chip().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix byte order of value assigned to pioavailshadow. This bug was
detected by sparse endianness warnings.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In mthca_alloc_icm_table(), the number of entries to allocate for the
table->icm array is computed by calculating obj_size * nobj and then
dividing by MTHCA_TABLE_CHUNK_SIZE. If nobj is really large, then
obj_size * nobj may overflow and the division may get the wrong value
(even a negative value). Fix this by calculating the number of
objects per chunk and then dividing nobj by this value instead.
This patch allows crazy configurations such as loading ib_mthca with
the module parameter num_mtt=33554432 to work properly.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_make_profile() returns the size in bytes of the HCA context
layout it creates, or a negative value if an error occurs. However,
the return value is declared as u64 and the memfree initialization
path casts this value to int to test if it is negative. This makes it
think incorrectly than an error has occurred if the context size
happens to be bigger than 2GB, since this turns into a negative int.
Fix this by having mthca_make_profile() return an s64 and testing
for an error by checking whether this 64-bit value itself is negative.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Pavel Emelyanov <xemul@openvz.org> mentioned in <http://lkml.org/lkml/2008/3/17/131>
that the task_struct->tgid field is about to become deprecated, so the
uses in the ehca driver need to be fixed up.
However, all the uses in ehca are for some object ownership checking
that is not really needed, and anyway is implementing a policy that
should be in common code rather than a low-level driver. So just
remove all the checks.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current SRP initiator will allow unlimited s/g entries in the
indirect descriptors lists, but the entry count field in the SRP_CMD
request is 8 bits, so setting srp_sg_tablesize too large will open the
possibility of wrapping the count and generating invalid requests.
Clamp srp_sg_tablesize to the protocol limits to prevent surprises.
Reported by Martin W. Schlining III <mschlining@datadirectnet.com>.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable use of 4KB MTU. Since the driver uses more pinned memory for
receive buffers when the 4KB MTU is enabled, whether or not the fabric
supports that MTU, add a "mtu4096" module parameter that can be used to
limit the MTU to 2KB when it is known that 4KB MTUs can't be used
anyway.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code was checking if units are present, but not that present units
were usable (link up, etc.)
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Modern I/O buses like PCIe and HT can be configured for multiple speeds
and widths. When an ipath HCA seems to have lower than expected
performance, it is very useful to be able to display what the driver
thinks the bus speed is.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes some constants chip-specific, and makes some related
changes to prepare for supporting another HCA.
Signed-off-by: Dave Olson <dave.olson@qlogic.com
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Recent sparse versions and kernel cleanups knock down the false positive
rate of the ipath driver code to a point where having it be sparse clean
is worthwhile. Here we fixup the sparse warnings. Some of these warnings
(and the impetus to run sparse again) are due to work by Roland Dreier.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Arbel and Sinai devices support checksum generation and verification
of TCP and UDP packets for UD IPoIB messages. This patch checks if
the HCA supports this and sets the IB_DEVICE_UD_IP_CSUM capability
flag if it does. It implements support for handling the IB_SEND_IP_CSUM
send flag and setting the csum_ok field in receive work completions.
Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX devices support checksum generation and verification of TCP
and UDP packets for UD IPoIB messages. This patch checks if the HCA
supports this and sets the IB_DEVICE_UD_IP_CSUM capability flag if it
does. It implements support for handling the IB_SEND_IP_CSUM send
flag and setting the csum_ok field in receive work completions.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Ali Ayub <ali@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For HCAs that support checksum offload (ie that set IB_DEVICE_UD_IP_CSUM
in the device capabilities flags), have IPoIB set NETIF_F_IP_CSUM and
use the HCA to generate and verify IP checksums.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
__FUNCTION__ is gcc-specific, use __func__ instead.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
