Convert PCMCIA drivers to use the dynamic debug infrastructure, instead of
requiring manual settings of PCMCIA_DEBUG.
Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.
CC: linux-mtd@lists.infradead.org
CC: linux-usb@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
prepare_discard_fn() was being called in a place where memory allocation
was effectively impossible. This makes it inappropriate for all but
the most trivial translations of Linux's DISCARD operation to the block
command set. Additionally adding a payload there makes the ownership
of the bio backing unclear as it's now allocated by the device driver
and not the submitter as usual.
It is replaced with QUEUE_FLAG_DISCARD which is used to indicate whether
the queue supports discard operations or not. blkdev_issue_discard now
allocates a one-page, sector-length payload which is the right thing
for the common ATA and SCSI implementations.
The mtd implementation of prepare_discard_fn() is replaced with simply
checking for the request being a discard.
Largely based on a previous patch from Matthew Wilcox <matthew@wil.cx>
which did the prepare_discard_fn but not the different payload allocation
yet.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (24 commits)
microblaze: Disable heartbeat/enable emaclite in defconfigs
microblaze: Support simpleImage.dts make target
microblaze: Fix _start symbol to physical address
microblaze: Use LOAD_OFFSET macro to get correct LMA for all sections
microblaze: Create the LOAD_OFFSET macro used to compute VMA vs LMA offsets
microblaze: Copy ppc asm-compat.h for clean handling of constants in asm and C
microblaze: Actually show KiB rather than pages in "Freeing initrd memory:"
microblaze: Support ptrace syscall tracing.
microblaze: Updated CPU version and FPGA family codes in PVR
microblaze: Generate correct signal and siginfo for integer div-by-zero
microblaze: Don't be noisy when userspace causes hardware exceptions
microblaze: Remove ipc.h file which points to non-existing asm-generic file
microblaze: Clear sticky FSR register after generating exception signals
microblaze: Ensure CPU usermode is set on new userspace processes
microblaze: Use correct kbuild variable KBUILD_CFLAGS
microblaze: Save and restore msr in hw exception
microblaze: Add architectural support for USB EHCI host controllers
microblaze: Implement include/asm/syscall.h.
microblaze: Improve checking mechanism for MSR instruction
microblaze: Add checking mechanism for MSR instruction
...
* git://git.infradead.org/mtd-2.6: (58 commits)
mtd: jedec_probe: add PSD4256G6V id
mtd: OneNand support for Nomadik 8815 SoC (on NHK8815 board)
mtd: nand: driver for Nomadik 8815 SoC (on NHK8815 board)
m25p80: Add Spansion S25FL129P serial flashes
jffs2: Use SLAB_HWCACHE_ALIGN for jffs2_raw_{dirent,inode} slabs
mtd: sh_flctl: register sh_flctl using platform_driver_probe()
mtd: nand: txx9ndfmc: transfer 512 byte at a time if possible
mtd: nand: fix tmio_nand ecc correction
mtd: nand: add __nand_correct_data helper function
mtd: cfi_cmdset_0002: add 0xFF intolerance for M29W128G
mtd: inftl: fix fold chain block number
mtd: jedec: fix compilation problem with I28F640C3B definition
mtd: nand: fix ECC Correction bug for SMC ordering for NDFC driver
mtd: ofpart: Check availability of reg property instead of name property
driver/Makefile: Initialize "mtd" and "spi" before "net"
mtd: omap: adding DMA mode support in nand prefetch/post-write
mtd: omap: add support for nand prefetch-read and post-write
mtd: add nand support for w90p910 (v2)
mtd: maps: add mtd-ram support to physmap_of
mtd: pxa3xx_nand: add single-bit error corrections reporting
...
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: improve NOR flash erasure quirk
UBI: introduce flash dump helper
UBI: eliminate possible undefined behaviour
UBI: print a warning if too many PEBs are corrupted
UBI: amend NOR flash pre-erase quirk
UBI: print a message if ECH is corrupted and VIDH is ok
Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions to the following modules from drivers/mtd/
devices/m25p80.c
devices/slram.c
linux version 2.6.30
ftl.c
nand/cafe_nand.c
nand/cmx270_nand.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As with orion_nand in commit f33dabbe79
("register orion_nand using platform_driver_probe()"), avoid .init.text
problems by using platform_device_probe(). This isn't going to be
hotplugged anyway.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Using __nand_correct_data() helper function, this driver can read 512
byte (with 6 byte ECC) at a time. This results minor performance
improvement.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver may be reading 512 bytes at a times, but still calculates
256-byte sector ECC. So the nand_correct_data() is not appropriate
for this driver. Implement its ecc.correct function calling
__nand_correct_data() twice.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Split nand_correct_data() into two part, a pure calculation function
and a wrapper for mtd interface.
The tmio_nand driver can implement its ecc.correct function easily
using this __nand_correct_data helper.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The M29W128G Numonyx flash devices are intolerant to any 0xFF command:
in the Cfi_util.c the function cfi_qry_mode_off() (that resets the device
after the autoselect mode) must have a 0xF0 command after the 0xFF command.
This fix solves also the cause of the fixup_M29W128G_write_buffer() fix,
that can be removed now.
The following patch applies to 2.6.30 kernel.
Signed-off-by: Massimo Cirillo <maxcir@gmail.com>
Acked-by: Alexey Korolev <akorolev@infradead.org>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix ECC Correction bug where the byte offset location were double
fliped causing correction routine to toggle the wrong byte location
in the ECC segment. The ndfc_calculate_ecc routine change the order
of getting the ECC code.
/* The NDFC uses Smart Media (SMC) bytes order */
ecc_code[0] = p[2];
ecc_code[1] = p[1];
ecc_code[2] = p[3];
But in the Correction algorithm when calculating the byte offset
location, the b1 is used as the upper part of the address. Which
again reverse the order making the final byte offset address
location incorrect.
byte_addr = (addressbits[b1] << 4) + addressbits[b0];
The order is change to read it in straight and let the correction
function to revert it to SMC order.
Cc: stable@kernel.org
Signed-off-by: Feng Kan <fkan@amcc.com>
Acked-by: Victor Gallardo <vgallardo@amcc.com>
Acked-by: Prodyut Hazarika <phazarika@amcc.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The previous implementation breaks the dts binding "mtd-physmap.txt". This
implementation fixes the issue by checking the availability of the reg
property instead of the name property.
Cc: stable@kernel.org
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds DMA mode support for nand prefetch/post-write engine.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds prefetch support to access nand flash in mpu mode.
This patch also adds 8-bit nand support (omap_read/write_buf8).
Prefetch can be used for both 8- and 16-bit devices.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add w90p910 NAND driver for w90p910 evaluation board
based on w90p910,there is a K8F1G08 NAND on my board.
[dwmw2: depend on MTD_PARTITIONS]
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use physmap_of to access RAMs as mtd and add documenation for it. This approach
is a lot less intrusive as adding an of-wrapper around plat-ram.c. As most
extensions of plat-ram.c (e.g. custom map-functions) can't be mapped to the
device tree anyhow, extending physmap_of seems to be the cleanest approach.
Tested with a phyCORE-MPC5121e.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Vitaly Wool <vwool@ru.mvista.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Ken MacLeod <ken@bitsko.slc.ut.us>
Cc: Albrecht Dreß <albrecht.dress@arcor.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch allows i.MX27 to support 2KiB pagesize NAND flash.
We are using a 1.8V NAND flash which datasheet (unfortunately only
available under NDA) says :
Page size: x8: 2,112 bytes (2,048 + 64 bytes).
Without this patch, all sectors are marked as bad eraseblock.
Signed-off-by: Eric Benard <ebenard@eukrea.com>
Acked-by : Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The error handling in the phram driver is pretty bad -- in many places,
errors are silently ignored or logged, but then still ignored in the
return value. So convert all of the code to pass back the correct return
value and log error messages properly (and using the new pr_fmt() helper).
If everything does go smoothly, rather than exit silently, dump a helpful
info message like pretty much every other MTD driver does.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Joern Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Support SST25WF{512,010,020,040} SPI flashes.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The SST SPI flashes are a bit non-standard in that they can be programmed
one byte at a time (including address!), or they can be written two bytes
at a time with auto address incrementing (AAI). The latter form is
obviously much better for performance, so let's use it when possible.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The MTD_TEST config option was added in between the MTD_PARTITIONS config
and its dependent options which causes the resulting menu system to
display incorrectly as MTD_TEST does not depend on MTD_PARTITIONS. So
move it up a few lines where it won't cause a problem.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver lets people use GPIO's for additional address lines in case
their processor does not have enough address lines already.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If MTD_RAM is built as a module, the uClinux map does not work since it
can only be built in to the kernel.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The uClinux map driver doesn't even use partitions, so we shouldn't require
it in order to work properly.
Signed-off-by: Timofei Bondarenko <tim@ipi.ac.ru>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
CC: Greg Ungerer <gerg@uclinux.org>
CC: uclinux-dev@uclinux.org
CC: linux-mtd@lists.infradead.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
linux v2.6.31-rc6 can not detect NEC uPD29F064115.
uPD29F064115 is a 16 bit device.
datasheet:
http://www.cn.necel.com/memory/cn/download/M16062EJ2V0DS00.pdf
This applies the same fix as used for SST chips in commit
ca6f12c67e ("jedec_probe: Fix SST 16-bit
chip detection").
Signed-off-by: Hiroshi Ito <ito@mlb.co.jp>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If the erase region was found in the first iteration we read from
regions[-1]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If the erase region was found in the first iteration we read from
eraseregions[-1]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds 4-bit ECC support for large page NAND chips using the new
ECC mode NAND_ECC_HW_OOB_FIRST. The platform data from board-dm355-evm
has been adjusted to use this mode.
The patches have been verified on DM355 device with 2KiB-page Micron
devices using mtd-tests and JFFS2. Error correction up to 4 bits has
also been verified using nandwrite/nanddump utilities.
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds the new mode NAND_ECC_HW_OOB_FIRST in the nand code to
support 4-bit ECC on TI DaVinci devices with large page (up to 2KiB) NAND
chips. This ECC mode is similar to NAND_ECC_HW, with the exception of
read_page API that first reads the OOB area, reads the data in chunks,
feeds the ECC from OOB area to the ECC hw engine and perform any
correction on the data as per the ECC status reported by the engine.
"ECC_HW_OOB_FIRST" name suggested by Thomas Gleixner
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs. The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove the ARM dependency from the generic "onenand" platform device
driver. This change makes the driver useful for other architectures as
well. Needed for the SuperH kfr2r09 board.
Apart from the obvious Kconfig bits, the most important change is the move
away from ARM specific includes and platform data. Together with this
change the only in-tree board code gets an update, and the driver name is
also changed gracefully break potential out of tree drivers.
The driver is also updated to allow NULL as platform data together with a
few changes to make use of resource_size() and dev_name().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
orion_nand_probe lives in .init.text, so using platform_driver_register to
register it is wrong because binding a device after the init memory is
discarded (e.g. via sysfs) results in an oops.
As requested by Nicolas Pitre platform_driver_probe is used instead of
moving the probe function to .devinit.text as proposed initially. This
saves some memory, but devices registered after the driver is probed are
not bound (probably there are none) and binding via sysfs isn't possible.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Joern Engel <joern@logfs.org>
Acked-by: Nicolas Pitre <nico@marvell.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add an omitted unlock to one sst25l_erase fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for the non JEDEC SST25L SPI Flash devices.
[dwmw2: Some cleanups]
Signed-off-by: Andre Renaud <andre@bluewatersys.com>
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: "H Hartley Sweeten" <hartleys@visionengravers.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
