Patch f598282f51 exposed a problem in
powerpc MSI-X functionality, making network interfaces such as ixgbe
and cxgb3 stop to work when MSI-X is enabled. RX interrupts were not
being generated.
The problem was caused because MSI irq was not being effectively
unmasked after device initialization.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a driver for the FIFO device on the LocalPlus bus on an mpc5200 system.
The driver supports programmed I/O through the FIFO as well as setting up DMA
via the BestComm engine through the FIFO.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When running Active Memory Sharing, the Collaborative Memory Manager (CMM)
may mark some pages as "loaned" with the hypervisor. Periodically, the
CMM will query the hypervisor for a loan request, which is a single signed
value. When kexec'ing into a kdump kernel, the CMM driver in the kdump
kernel is not aware of the pages the previous kernel had marked as "loaned",
so the hypervisor and the CMM driver are out of sync. Fix the CMM driver
to handle this scenario by ignoring requests to decrease the number of loaned
pages if we don't think we have any pages loaned. Pages that are marked as
"loaned" which are not in the balloon will automatically get switched to "active"
the next time we touch the page. This also fixes the case where totalram_pages
is smaller than min_mem_mb, which can occur during kdump.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
get_irq_desc() is a powerpc-specific version of irq_to_desc(). That
is reason enough to remove it, but it also doesn't know about sparse
irq_desc support which irq_to_desc() does (when we enable it).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rather than open-coding our own check, use irq_has_action()
to check if an irq has an action - ie. is "in use".
irq_has_action() doesn't take the descriptor lock, but it
shouldn't matter - we're just using it as an indicator
that the irq is in use. disable_irq_nosync() will take
the descriptor lock before doing anything also.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The CHRP code has some fishy timer based code to scan the RTAS event
log, which uses a 1KB stack buffer and doesn't even use the results.
The pSeries code as a nicer daemon that allows userspace to read the
event log and basically uses the same RTAS interface
This patch moves rtasd.c out of platform/pseries and makes it usable
by CHRP, after removing the old crufty event log mechanism in there.
The nvram logging part of the daemon is still only available on 64-bit
since the underlying nvram management routines aren't currently shared.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some of the stuff in /proc/ppc64 such as the RTAS bits are actually
useful to some 32-bit platforms. Rename the file, and create a
symlink on 64-bit for backward compatibility
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The non-debug case in ps3/mm.c uses pr_debug(), so that the compiler
still does type checks etc. and doesn't complain about unused
variables in the non-debug case.
However with DEBUG=n and CONFIG_DYNAMIC_DEBUG=y there's still code
generated for those pr_debugs().
size before:
text data bss dec hex filename
17553 4112 88 21753 54f9 arch/powerpc/platforms/ps3/mm.o
size after:
text data bss dec hex filename
7377 776 88 8241 2031 arch/powerpc/platforms/ps3/mm.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch updates percpu related symbols in powerpc such that percpu
symbols are unique and don't clash with local symbols. This serves
two purposes of decreasing the possibility of global percpu symbol
collision and allowing dropping per_cpu__ prefix from percpu symbols.
* arch/powerpc/kernel/perf_callchain.c: s/callchain/cpu_perf_callchain/
* arch/powerpc/kernel/setup-common.c: s/pvr/cpu_pvr/
* arch/powerpc/platforms/pseries/dtl.c: s/dtl/cpu_dtl/
* arch/powerpc/platforms/cell/interrupt.c: s/iic/cpu_iic/
Partly based on Rusty Russell's "alloc_percpu: rename percpu vars
which cause name clashes" patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@ozlabs.org
While most users of the hcall tracepoints will only want the opcode
and return code, some will want all the arguments. To avoid the
complexity of using varargs we pass a pointer to the register save
area, which contains all the arguments.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add hcall_entry and hcall_exit tracepoints. This replaces the inline
assembly HCALL_STATS code and converts it to use the new tracepoints.
To keep the disabled case as quick as possible, we embed a status word
in the TOC so we can get at it with a single load. By doing so we
keep the overhead at a minimum. Time taken for a null hcall:
No tracepoint code: 135.79 cycles
Disabled tracepoints: 137.95 cycles
For reference, before this patch enabling HCALL_STATS resulted in a null
hcall of 201.44 cycles!
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The creation of the flattened device tree depended on the compiler
putting the constant strings for an object in a section with a
particular name. This was changed with recent compilers. Do this
explicitly instead.
Without this patch, iseries kernels may silently not boot when built with
some compilers.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- serial Console on PSC1
- 64MB SDRAM
- MTD CFI Flash
- Ethernet FEC
- IDE support
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
- serial Console on PSC1
- 64MB SDRAM
- MTD CFI Flash
- Ethernet FEC
- I2C with PCF8563 and Temp. Sensor ADM9240
- IDE support
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Profiling of a page fault scalability microbenchmark shows flush_hash_range
is not calling the batch hpte invalidate hcall (H_BULK_REMOVE).
It turns out we have a duplicate firmware feature for hcall-bulk and the
current setup code stops after finding the first match. This meant we never
batch and always do individual invalidates.
The patch below removes the duplicate and shifts FW_FEATURE_CMO to close
the gap. With the patch applied the single threaded page fault rate improves
from 217169 to 238755 per second on a POWER5 test box, a 10% improvement.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cppcheck found a memory leak in axon_msi, if dcr_base or dcr_len are zero,
we have already allocated msic, so we should free it in the error path.
Signed-off-by: Eric Sesterhenn <eric.sesterhenn@lsexperts.de>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the change of how interrupts are disabled during suspend,
certain PowerBook models started exhibiting various issues during
suspend or resume from sleep.
I finally tracked it down to the code that runs various "platform"
functions (kind of little scripts extracted from the device-tree),
which uses our i2c and PMU drivers expecting interrutps to work,
and at a time where with the new scheme, they have been disabled.
This causes timeouts internally which for some reason results in
the PMU being unable to see the trackpad, among other issues, really
it depends on the machine. Most of the time, we fail to properly adjust
some clocks for suspend/resume so the results are not always
predictable.
This patch fixes it by using IRQF_TIMER for both the PMU and the I2C
interrupts. I prefer doing it this way than moving the call sites since
I really want those platform functions to still be called after all
drivers (and before sysdevs).
We also do a slight cleanup to via-pmu.c driver to make sure the
ADB autopoll mask is handled correctly when doing bus resets
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes this is used to hold a simple offset, and sometimes
it is used to hold a pointer. This patch changes it to a union containing
void * and dma_addr_t. get/set accessors are also provided, because it was
getting a bit ugly to get to the actual data.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the accessors rather than frobbing bits directly (the new versions
are const).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Make all seq_operations structs const, to help mitigate against
revectoring user-triggerable function pointers.
This is derived from the grsecurity patch, although generated from scratch
because it's simpler than extracting the changes from there.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
* 'perfcounters-rename-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Tidy up after the big rename
perf: Do the big rename: Performance Counters -> Performance Events
perf_counter: Rename 'event' to event_id/hw_event
perf_counter: Rename list_entry -> group_entry, counter_list -> group_list
Manually resolved some fairly trivial conflicts with the tracing tree in
include/trace/ftrace.h and kernel/trace/trace_syscalls.c.
Bye-bye Performance Counters, welcome Performance Events!
In the past few months the perfcounters subsystem has grown out its
initial role of counting hardware events, and has become (and is
becoming) a much broader generic event enumeration, reporting, logging,
monitoring, analysis facility.
Naming its core object 'perf_counter' and naming the subsystem
'perfcounters' has become more and more of a misnomer. With pending
code like hw-breakpoints support the 'counter' name is less and
less appropriate.
All in one, we've decided to rename the subsystem to 'performance
events' and to propagate this rename through all fields, variables
and API names. (in an ABI compatible fashion)
The word 'event' is also a bit shorter than 'counter' - which makes
it slightly more convenient to write/handle as well.
Thanks goes to Stephane Eranian who first observed this misnomer and
suggested a rename.
User-space tooling and ABI compatibility is not affected - this patch
should be function-invariant. (Also, defconfigs were not touched to
keep the size down.)
This patch has been generated via the following script:
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/PERF_EVENT_/PERF_RECORD_/g' \
-e 's/PERF_COUNTER/PERF_EVENT/g' \
-e 's/perf_counter/perf_event/g' \
-e 's/nb_counters/nb_events/g' \
-e 's/swcounter/swevent/g' \
-e 's/tpcounter_event/tp_event/g' \
$FILES
for N in $(find . -name perf_counter.[ch]); do
M=$(echo $N | sed 's/perf_counter/perf_event/g')
mv $N $M
done
FILES=$(find . -name perf_event.*)
sed -i \
-e 's/COUNTER_MASK/REG_MASK/g' \
-e 's/COUNTER/EVENT/g' \
-e 's/\<event\>/event_id/g' \
-e 's/counter/event/g' \
-e 's/Counter/Event/g' \
$FILES
... to keep it as correct as possible. This script can also be
used by anyone who has pending perfcounters patches - it converts
a Linux kernel tree over to the new naming. We tried to time this
change to the point in time where the amount of pending patches
is the smallest: the end of the merge window.
Namespace clashes were fixed up in a preparatory patch - and some
stylistic fallout will be fixed up in a subsequent patch.
( NOTE: 'counters' are still the proper terminology when we deal
with hardware registers - and these sed scripts are a bit
over-eager in renaming them. I've undone some of that, but
in case there's something left where 'counter' would be
better than 'event' we can undo that on an individual basis
instead of touching an otherwise nicely automated patch. )
Suggested-by: Stephane Eranian <eranian@google.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that the last users of markers have migrated to the event
tracer we can kill off the (now orphan) support code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090917173527.GA1699@lst.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
PCI hotplug: clean up acpi_run_hpp()
PCI hotplug: acpiphp: use generic pci_configure_slot()
PCI hotplug: shpchp: use generic pci_configure_slot()
PCI hotplug: pciehp: use generic pci_configure_slot()
PCI hotplug: add pci_configure_slot()
PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
PCI: Clear saved_state after the state has been restored
PCI PM: Return error codes from pci_pm_resume()
PCI: use dev_printk in quirk messages
PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
PCI Hotplug: acpiphp: find bridges the easy way
PCI: pcie portdrv: remove unused variable
PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
ACPI PM: Replace wakeup.prepared with reference counter
PCI PM: Introduce device flag wakeup_prepared
PCI / ACPI PM: Rework some debug messages
PCI PM: Simplify PCI wake-up code
...
Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases. The
'needs_freset' initialization added in 6e19314cc ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (134 commits)
powerpc/nvram: Enable use Generic NVRAM driver for different size chips
powerpc/iseries: Fix oops reading from /proc/iSeries/mf/*/cmdline
powerpc/ps3: Workaround for flash memory I/O error
powerpc/booke: Don't set DABR on 64-bit BookE, use DAC1 instead
powerpc/perf_counters: Reduce stack usage of power_check_constraints
powerpc: Fix bug where perf_counters breaks oprofile
powerpc/85xx: Fix SMP compile error and allow NULL for smp_ops
powerpc/irq: Improve nanodoc
powerpc: Fix some late PowerMac G5 with PCIe ATI graphics
powerpc/fsl-booke: Use HW PTE format if CONFIG_PTE_64BIT
powerpc/book3e: Add missing page sizes
powerpc/pseries: Fix to handle slb resize across migration
powerpc/powermac: Thermal control turns system off too eagerly
powerpc/pci: Merge ppc32 and ppc64 versions of phb_scan()
powerpc/405ex: support cuImage via included dtb
powerpc/405ex: provide necessary fixup function to support cuImage
powerpc/40x: Add support for the ESTeem 195E (PPC405EP) SBC
powerpc/44x: Add Eiger AMCC (AppliedMicro) PPC460SX evaluation board support.
powerpc/44x: Update Arches defconfig
powerpc/44x: Update Arches dts
...
Fix up conflicts in drivers/char/agp/uninorth-agp.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (46 commits)
powerpc64: convert to dynamic percpu allocator
sparc64: use embedding percpu first chunk allocator
percpu: kill lpage first chunk allocator
x86,percpu: use embedding for 64bit NUMA and page for 32bit NUMA
percpu: update embedding first chunk allocator to handle sparse units
percpu: use group information to allocate vmap areas sparsely
vmalloc: implement pcpu_get_vm_areas()
vmalloc: separate out insert_vmalloc_vm()
percpu: add chunk->base_addr
percpu: add pcpu_unit_offsets[]
percpu: introduce pcpu_alloc_info and pcpu_group_info
percpu: move pcpu_lpage_build_unit_map() and pcpul_lpage_dump_cfg() upward
percpu: add @align to pcpu_fc_alloc_fn_t
percpu: make @dyn_size mandatory for pcpu_setup_first_chunk()
percpu: drop @static_size from first chunk allocators
percpu: generalize first chunk allocator selection
percpu: build first chunk allocators selectively
percpu: rename 4k first chunk allocator to page
percpu: improve boot messages
percpu: fix pcpu_reclaim() locking
...
Fix trivial conflict as by Tejun Heo in kernel/sched.c
That code uses dma_mapping_error() with a NULL device, which is
a bad idea :-) The proper fix might be to start using some kind
of pseudo device for all these low level mappings with the
hypervisor but that will be for another day. Since it directly
calls into the low level iommu code, I see no problem in having
it directly test against DMA_ERROR_CODE instead of using the
accessors with a NULL argument for now.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently there is a bug where if you use oprofile on a pSeries
machine, then use perf_counters, then use oprofile again, oprofile
will not work correctly; it will lose the PMU configuration the next
time the hypervisor does a partition context switch, and thereafter
won't count anything.
Maynard Johnson identified the sequence causing the problem:
- oprofile setup calls ppc_enable_pmcs(), which calls
pseries_lpar_enable_pmcs, which tells the hypervisor that we want
to use the PMU, and sets the "PMU in use" flag in the lppaca.
This flag tells the hypervisor whether it needs to save and restore
the PMU config.
- The perf_counter code sets and clears the "PMU in use" flag directly
as it context-switches the PMU between tasks, and leaves it clear
when it finishes.
- oprofile setup, called for a new oprofile run, calls ppc_enable_pmcs,
which does nothing because it has already been called. In particular
it doesn't set the "PMU in use" flag.
This fixes the problem by arranging for ppc_enable_pmcs to always set
the "PMU in use" flag. It makes the perf_counter code call
ppc_enable_pmcs also rather than calling the lower-level function
directly, and removes the setting of the "PMU in use" flag from
pseries_lpar_enable_pmcs, since that is now done in its caller.
This also removes the declaration of pasemi_enable_pmcs because it
isn't defined anywhere.
Reported-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: <stable@kernel.org)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The following commit introduced a compile error since it removed
the implementation of smp_85xx_basic_setup:
commit 77c0a700c1
Author: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Date: Fri Aug 28 14:25:04 2009 +1000
powerpc: Properly start decrementer on BookE secondary CPUs
Make it so that smp_ops probe() and setup_cpu() can be set to NULL.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
By default, the EEH framework on powerpc does what's known as a "hot
reset" during recovery of a PCI Express device. We've found a case
where the device needs a "fundamental reset" to recover properly. The
current PCI error recovery and EEH frameworks do not support this
distinction.
The attached patch makes changes to EEH to utilize the new bit field.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Richard Lary <rlary@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A misconfiguration by the firmware of the U4 PCIe bridge on PowerMac G5
with the U4 bridge (latest generations, may also affect the iMac G5
"iSight") is causing us to re-assign the PCI BARs of the video card,
which can get it out of sync with the firmware, thus breaking offb.
This works around it by fixing up the bridge configuration properly
at boot time. It also fixes a bug where the firmware provides us with
an incorrect set of accessible regions in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The SLB can change sizes across a live migration, which was not
being handled, resulting in possible machine crashes during
migration if migrating to a machine which has a smaller max SLB
size than the source machine. Fix this by first reducing the
SLB size to the minimum possible value, which is 32, prior to
migration. Then during the device tree update which occurs after
migration, we make the call to ensure the SLB gets updated. Also
add the slb_size to the lparcfg output so that the migration
tools can check to make sure the kernel has this capability
before allowing migration in scenarios where the SLB size will change.
BenH: Fixed #include <asm/mmu-hash64.h> -> <asm/mmu.h> to avoid
breaking ppc32 build
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The two versions are doing almost exactly the same thing. No need to
maintain them as separate files. This patch also has the side effect
of making the PCI device tree scanning code available to 32 bit powerpc
machines, but no board ports actually make use of this feature at this
point.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for the ESTeem 195E Hotfoot SBC.
There are several variants of the SBC deployed, single/dual
ethernet+serial, and also 4MB/8MB flash variations. In the interest of
having a single kernel image boot on all boards, the cuboot shim detects
the differences and mangles the DTS tree appropriately.
With the exception of the CF interface that was never populated on
production boards, this code/DTS supports all boardpop options.
Signed-off-by: Solomon Peachy <solomon@linux-wlan.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds support for the AMCC (AppliedMicro) PPC460SX Eiger evaluation
board.
Signed-off-by: Tai Tri Nguyen <ttnguyen@amcc.com>
Acked-by: Feng Kan <fkan@amcc.com>
Acked-by: Tirumala Marri <tmarri@amcc.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This moves the code to start the decrementer on 40x and BookE into
a separate function which is now called from time_init() and
secondary_time_init(), before the respective clock sources are
registered. We also remove the 85xx specific code for doing it
from the platform code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This converts uses dma_map_ops struct (in include/linux/dma-mapping.h)
instead of POWERPC homegrown dma_mapping_ops.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now swiotlb_pci_dma_ops is identical to swiotlb_dma_ops; we can use
swiotlb_dma_ops with any devices. This removes swiotlb_pci_dma_ops.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds max_direct_dma_addr to struct dev_archdata to remove
addr_needs_map in struct dma_mapping_ops. It also converts
dma_capable() to use max_direct_dma_addr.
max_direct_dma_addr is initialized in pci_dma_dev_setup_swiotlb(),
called via ppc_md.pci_dma_dev_setup hook.
For further information:
http://marc.info/?t=124719060200001&r=1&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On non-PS3, we get:
| kernel BUG at drivers/rtc/rtc-ps3.c:36!
because the rtc-ps3 platform device is registered unconditionally in a kernel
with builtin support for PS3.
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On Thu, Aug 13, 2009 at 04:14:58PM +1000, Benjamin Herrenschmidt wrote:
> On Tue, 2009-08-11 at 11:39 +0200, Bastian Blank wrote:
> > This patch just disables this driver on SMP kernels, as it is obviously
> > not supported.
> Why not remove the #error instead ? :-) I don't think it's still
> meaningful, especially since we use the timebase for delays nowadays
> which doesn't depend on the CPU frequency...
Your call. Take this one:
The build of a PowerMac 32bit kernel currently fails with
error: #warning "WARNING, CPUFREQ not recommended on SMP kernels"
Thie patch removes the not longer applicable SMP warning from the
PowerMac cpufreq code.
Signed-off-by: Bastian Blank <waldi@debian.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- Add gpio-controller node for BCSR17, it is used to control USB
speed and VBUS;
- Add timer node for QE GTM, needed for USB host;
- Add usb node itself;
- Add some probing code for BCSR GPIOs.
NOTE: QE USB doesn't work on prototype boards, but should work on
pilot boards if specs and schematics are correct, though we
don't have the pilot boards to actually test it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add usb node;
- Configure pins and clocks;
- Enable USB function in BCSR.
The support was successfully tested using serial and ethernet gadget
drivers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8272_ads.c is using BCSR bits definitions from pq2ads.h, but
according to User's Guide the bits are wrong for MPC8272ADS boards
(I guess definitions from pq2ads should only be used for PQ2FADS
boards).
So, let's introduce our own definitions for MPC8272ADS, and don't
include pq2ads.h.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The existing fsl_rstcr_restart function is not applicable to the
mpc8560. The Global Utilities Block on this earlier CPU doesn't have
the control/reset register at 0xe00b0. This implements a board
specific reset function that uses the RCR(Reset Control Register) of
the sbc8560's EPLD to do a reset.
Signed-off-by: Liang Li <Liang.Li@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As <asm/iommu.h> doesn't contain any other hardware specific definitions
but only interfaces.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These changes were a direct result of using a semantic patch
More information can be found at http://www.emn.fr/x-info/coccinelle/
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I wrote sputrace before generic tracing infrastrucure was available.
Now that we have the generic event tracer we can convert it over and
remove a lot of code:
8 files changed, 45 insertions(+), 285 deletions(-)
To use it make sure CONFIG_EVENT_TRACING is enabled and then enable
the spufs trace channel by
echo 1 > /sys/kernel/debug/tracing/events/spufs/spufs_context/enable
and then read the trace records using e.g.
cat /sys/kernel/debug/tracing/trace
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
/proc/cpuinfo should be showing the boards revision and the revision of
the FPGA fitted. The functions currently used to access this information
as incorrect.
Additionally the VME geographical address of the PPC9A and it's status as
system contoller are available in the board registers. Show these in
cpuinfo.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Actually, the support is already there, but it requires newer U-Boots
(to fill-in clock-frequency, and setup pin multiplexing).
Though, it appears that on RDB boards USBB pins aren't multiplexed
between USB and eSDHC (unlike MDS boards, where USB and eSDHC share
pctl and pwrfault pins).
So, for RDB boards we can safely setup pinmux and manually fill-in
clock-frequency, thus making eSDHC work even with older u-boots.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- add I2C support
- add FCC1 and FCC2 support
- fix bogus gpio numbering in plattform code
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This contains all the bits that didn't fit in previous patches :-) This
includes the actual exception handlers assembly, the changes to the
kernel entry, other misc bits and wiring it all up in Kconfig.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Those definitions are currently declared extern in the .c file where
they are used, move them to a header file instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The code for setting up the IPIs for SMP PowerSurge marchines bitrot,
it needs to properly map the HW interrupt number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace strncpy() and explicit null-termination by strlcpy()
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The STAB code used on Power3 and RS/64 uses a second scratch SPRG to
save a GPR in order to decide whether to go to do_stab_bolted_* or
to handle a normal data access exception.
This prevents our scheme of freeing SPRG3 which is user visible for
user uses since we cannot use SPRG0 which, on RS/64, seems to be
read-only for supervisor mode (like POWER4).
This reworks the STAB exception entry to use the PACA as temporary
storage instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kernel uses SPRG registers for various purposes, typically in
low level assembly code as scratch registers or to hold per-cpu
global infos such as the PACA or the current thread_info pointer.
We want to be able to easily shuffle the usage of those registers
as some implementations have specific constraints realted to some
of them, for example, some have userspace readable aliases, etc..
and the current choice isn't always the best.
This patch should not change any code generation, and replaces the
usage of SPRN_SPRGn everywhere in the kernel with a named replacement
and adds documentation next to the definition of the names as to
what those are used for on each processor family.
The only parts that still use the original numbers are bits of KVM
or suspend/resume code that just blindly needs to save/restore all
the SPRGs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The file include/asm/exception.h contains definitions
that are specific to exception handling on 64-bit server
type processors.
This renames the file to exception-64s.h to reflect that
fact and avoid confusion.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This allows to remove the ppc_md.init() hook in the setup code.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Conflicts:
arch/sparc/kernel/smp_64.c
arch/x86/kernel/cpu/perf_counter.c
arch/x86/kernel/setup_percpu.c
drivers/cpufreq/cpufreq_ondemand.c
mm/percpu.c
Conflicts in core and arch percpu codes are mostly from commit
ed78e1e078dd44249f88b1dd8c76dafb39567161 which substituted many
num_possible_cpus() with nr_cpu_ids. As for-next branch has moved all
the first chunk allocators into mm/percpu.c, the changes are moved
from arch code to mm/percpu.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Linux isn't able to detect link changes on ethernet ports that were
used by U-Boot. This is because U-Boot wrongly clears interrupt
polarity bit (INTPOL, 0x400) in the extended status register (EXT_SR,
0x1b) of Marvell PHYs.
There is no easy way for PHY drivers to know IRQ line polarity (we
could extract it from the device tree and pass it to phydevs, but
that'll be quite a lot of work), so for now just reset the PHYs to
their default states.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
7083 1616 0 8699 21fb arch/powerpc/../axon_msi.o
size after:
text data bss dec hex filename
5772 1208 0 6980 1b44 arch/powerpc/../axon_msi.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
7720 5488 296 13504 34c0 platforms/pseries/xics.o
size after:
text data bss dec hex filename
7535 5456 296 13287 33e7 platforms/pseries/xics.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
In particular, pSeries_lpar_hpte_insert() goes from 185 instructions
to 77 instructions as a result of this patch. Luckily that code
isn't called very often ...
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
7284 1552 296 9132 23ac platforms/pseries/lpar.o
size after:
text data bss dec hex filename
5806 1096 296 7198 1c1e platforms/pseries/lpar.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With -Werror enabled during the build, the warp.c file fails to build
due to the temp_isr function not containing a return statement. This
fixes the build error and documents that the function never returns.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The GPIO LEDS driver now has a default state of "keep". Update the Warp DTS
and platform file to take advantage of this new state. This removes the
hardcoding of the two LEDs on the Warp.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Pull linus#master to merge PER_CPU_DEF_ATTRIBUTES and alpha build fix
changes. As alpha in percpu tree uses 'weak' attribute instead of
inline assembly, there's no need for __used attribute.
Conflicts:
arch/alpha/include/asm/percpu.h
arch/mn10300/kernel/vmlinux.lds.S
include/linux/percpu-defs.h
spin_lock() can hang if called while the timebase is frozen,
so use a raw lock instead, also disable interrupts while
at it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Several platforms use their own copy of what is essentially the same code,
using RTAS to synchronize the timebases when bringing up new CPUs. This
moves it all into a single common implementation and additionally
turns the spinlock into a raw spinlock since the former can rely on
the timebase not being frozen when spinlock debugging is enabled, and finally
masks interrupts while the timebase is disabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The old PowerSurge SMP (ie, dual or quad 604 machines) code has
numerous issues in modern world.
One is cpu_possible_map is set too late (the device-tree is bogus)
so we fail to allocate the interrupt stacks and crash. Another
problem is the fact the timebase is frozen by the bringup of the
second CPU so the delays in the generic code will hang, we need
to move some of the calling procedure to inside the powermac code.
This makes it boot again for me
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A change to the i2c subsystem breaks the warp platform code. The patch
is cleaner anyway, the old way was a bit crufty.
For those with keen eyes, the gratuitous change in the string from
PIKA to Warp is just so the logs look a bit nicer. The following two
lines tend to be printed one after another.
Warp POST OK
Warp DTM thread running.
Yeah, this will be the third patch to warp.c submitted in this
release....
Cheers,
Sean
The i2c_client struct changed, breaking the code that looked for the ad7414
chip. Use the new of_find_i2c_device_by_node function added in 2.6.29.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the following three different ways to define percpu arrays
are in use.
1. DEFINE_PER_CPU(elem_type[array_len], array_name);
2. DEFINE_PER_CPU(elem_type, array_name[array_len]);
3. DEFINE_PER_CPU(elem_type, array_name)[array_len];
Unify to #1 which correctly separates the roles of the two parameters
and thus allows more flexibility in the way percpu variables are
defined.
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: linux-mm@kvack.org
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: David S. Miller <davem@davemloft.net>
FSL RapidIO won't probe without a proper compatible entry. This
patch fixes the issue by adding fsl,rapidio-delta compatible to
mpc85xx_ids.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Match what other 85xx platforms do for of_platform_bus_probe and use
machine_device_initcall. This is one small step in killing of
ppc_md.init.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
PCI: Fix the NIU MSI-X problem in a better way
PCI ASPM: remove get_root_port_link
PCI ASPM: cleanup pcie_aspm_sanity_check
PCI ASPM: remove has_switch field
PCI ASPM: cleanup calc_Lx_latency
PCI ASPM: cleanup pcie_aspm_get_cap_device
PCI ASPM: cleanup clkpm checks
PCI ASPM: cleanup __pcie_aspm_check_state_one
PCI ASPM: cleanup initialization
PCI ASPM: cleanup change input argument of aspm functions
PCI ASPM: cleanup misc in struct pcie_link_state
PCI ASPM: cleanup clkpm state in struct pcie_link_state
PCI ASPM: cleanup latency field in struct pcie_link_state
PCI ASPM: cleanup aspm state field in struct pcie_link_state
PCI ASPM: fix typo in struct pcie_link_state
PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
PCI: remove redundant __msi_set_enable()
PCI PM: consistently use type bool for wake enable variable
x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
...
This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault(). All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (49 commits)
perfcounter: Handle some IO return values
perf_counter: Push perf_sample_data through the swcounter code
perf_counter tools: Define and use our own u64, s64 etc. definitions
perf_counter: Close race in perf_lock_task_context()
perf_counter, x86: Improve interactions with fast-gup
perf_counter: Simplify and fix task migration counting
perf_counter tools: Add a data file header
perf_counter: Update userspace callchain sampling uses
perf_counter: Make callchain samples extensible
perf report: Filter to parent set by default
perf_counter tools: Handle lost events
perf_counter: Add event overlow handling
fs: Provide empty .set_page_dirty() aop for anon inodes
perf_counter: tools: Makefile tweaks for 64-bit powerpc
perf_counter: powerpc: Add processor back-end for MPC7450 family
perf_counter: powerpc: Make powerpc perf_counter code safe for 32-bit kernels
perf_counter: powerpc: Change how processor-specific back-ends get selected
perf_counter: powerpc: Use unsigned long for register and constraint values
perf_counter: powerpc: Enable use of software counters on 32-bit powerpc
perf_counter tools: Add and use isprint()
...
This patch adds spi and mmc-spi-slot nodes, plus a gpio-controller for
PIXIS' sdcsr bank that is used for managing SPI chip-select and for
reading card's states.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the number of cells for the values of CPC925 Memory Controller,
and setup related platform device during system booting up, against
which CPC925 Memory Controller EDAC driver would be matched.
Signed-off-by: Harry Ciao <qingtao.cao@windriver.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for the performance monitor hardware on the
MPC7450 family of processors (7450, 7451, 7455, 7447/7457, 7447A,
7448), used in the later Apple G4 powermacs/powerbooks and other
machines. These machines have 6 hardware counters with a unique
set of events which can be counted on each counter, with some
events being available on multiple counters.
Raw event codes for these processors are (PMC << 8) + PMCSEL.
If PMC is non-zero then the event is that selected by the given
PMCSEL value for that PMC (hardware counter). If PMC is zero
then the event selected is one of the low-numbered ones that are
common to several PMCs. In this case PMCSEL must be <= 22 and
the event is what that PMCSEL value would select on PMC1 (but
it may be placed any other PMC that has the same event for that
PMCSEL value).
For events that count cycles or occurrences that exceed a threshold,
the threshold requested can be specified in the 0x3f000 bits of the
raw event codes. If the event uses the threshold multiplier bit
and that bit should be set, that is indicated with the 0x40000 bit
of the raw event code.
This fills in some of the generic cache events. Unfortunately there
are quite a few blank spaces in the table, partly because these
processors tend to count cache hits rather than cache accesses.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55631.802122.696927@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This enables the perf_counter subsystem on 32-bit powerpc. Since we
don't have any support for hardware counters on 32-bit powerpc yet,
only software counters can be used.
Besides selecting HAVE_PERF_COUNTERS for 32-bit powerpc as well as
64-bit, the main thing this does is add an implementation of
set_perf_counter_pending(). This needs to arrange for
perf_counter_do_pending() to be called when interrupts are enabled.
Rather than add code to local_irq_restore as 64-bit does, the 32-bit
set_perf_counter_pending() generates an interrupt by setting the
decrementer to 1 so that a decrementer interrupt will become pending
in 1 or 2 timebase ticks (if a decrementer interrupt isn't already
pending). When interrupts are enabled, timer_interrupt() will be
called, and some new code in there calls perf_counter_do_pending().
We use a per-cpu array of flags to indicate whether we need to call
perf_counter_do_pending() or not.
This introduces a couple of new Kconfig symbols: PPC_HAVE_PMU_SUPPORT,
which is selected by processor families for which we have hardware PMU
support (currently only PPC64), and PPC_PERF_CTRS, which enables the
powerpc-specific perf_counter back-end.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linuxppc-dev@ozlabs.org
Cc: benh@kernel.crashing.org
LKML-Reference: <19000.55404.103840.393470@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
