This fixes the problem of getting extra bytes inserted at the
beginning of a recording when using the Apple i2s interface and DBDMA
controller. It turns out that we can't just abort the DMA; we have to
let it stop at the end of a command, and then wait for the S7 bit to
be set before turning off the DBDMA controller. Doing that for
playback doesn't seem to be necessary, but doesn't hurt either.
We use the technique used by the Darwin driver: make each transfer
command branch to a stop command if the S0 status bit is set. Thus we
can ask the DMA controller to stop at the end of the current command
by setting S0.
The interrupt routine now looks at and clears the status word of the
DBDMA command ring. This is necessary so it can know when the DBDMA
controller has seen that S0 is set, and so when it should look for the
DBDMA controller being stopped and S7 being set. This also ended up
simplifying the calculation in i2sbus_pcm_pointer.
Tested on a 15 inch albook.
[Addition by Johannes]
I modified this patch and added the suspend/resume bits to it to get my
powermac into a decent state when playing sound across suspend to disk
that has a different bitrate from what the firmware programs the
hardware to.
I also added the SNDRV_PCM_INFO_JOINT_DUPLEX flag because it seemed the
right thing to do and I was looking at the info stuff.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This just removes two useless printks.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
When the machine resumes the onyx codec might be in a weird state. Hence,
simply fully reset it once (and keep the code to take it out of suspend in
case the suspend of the codec chip survives a reset).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
create sysfs driver symlink for snd-aoa in /sys/bus/aoa-soundbus/devices/*/
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
create sysfs device symlinks for snd-aoa in /sys/class/sound/controlC0 This
allows hald to recognize the device as sound device. Furthermore it allows
the desktop user to actually access the sound device nodes. hald and
related packages will modify the acl attributes.
Fixes https://bugzilla.novell.com/show_bug.cgi?id=106294
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch changes i2sbus_attach_codec to implement a proper error handling
strategy using labels to jump to the right part. Since it has an elaborate
set-up sequence it also needs that tear-down, which I had hard-coded
inbetween all the checks. This increases readability and should reduce .text
size as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch makes a few whitespace cleanups and makes i2sbus assign the new
struct device pointer in struct snd_pcm so that the proper device symlink
shows up in sysfs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Don't include <linux/i2c-dev.h> as it's not needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Standardize the miniscule percentage of occurrences of "depends" in
Kconfig files to "depends on", and update kconfig-language.txt to
reflect that.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
Despite what the data sheet says in one place, to get stereo input
from input A (line in), we have to clear the 'input B monaural' bit in
the ACR.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Looks like I completely forgot to do this. This patch adds locking to
the tas codec so two userspace programs can't hit the controls at the
same time. Tested on my powerbook, but I obviously can't find any
problems even without it since it doesn't do SMP.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the missing selection of I2C and I2C_POWERMAC
for Onyx and TAS codecs in aoa/codecs/Kconfig.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Sometimes we simply want to turn off or on everything, and when recently a
warning was added when a certain platform function can't be called, this
triggered all the time in those cases. This patch shows the warning only if
the error was different from the function not existing.
The alternative would be to not even try calling the function when it
doesn't exist by first checking which exist and then only calling those that
do, but that adds complexity that isn't necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes the toonie codec to be actually usable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The IRQ rework caused some hiccups here, in some cases we call
get_irq without a device node. This patch makes it catch that
case and return NO_IRQ when it happens, along with changing the
place where the irq is checked to check for NO_IRQ instead of -1.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
powerpc-specific sound driver changes.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the bass/treble controls to snd-aoa that snd-powermac always
had for tas3004 based machines.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The layout fabric gained support for all IDs when I extracted those from the
OSX description file. But apparently I had forgotten to add them all as
module aliases so the module will also load. This patch adds them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes the DRC control visible again for TAS chips.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the initialisation and reset of the tas codec. The tas will
often reset if the i2s clocks go away so it needs to be completely
re-initialised when clocks come back.
Also, this patch adds some code for DRC that will be exploited later to add a
DRC control again, fixing a regression over snd-powermac.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the PCM1 control name to PCM to make it play nice with the
softvol plugin (which will then go away if it sees a proper PCM slider)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch cleans up the printk's in the layout fabric and also makes it
display which type of GPIO access it is going to use.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes the pmf GPIO layer in aoa report if calling a platform
function failed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch revamps the i2sbus control layer by using the macio/keylargo
functions instead of directly mapping.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes initialisation issues when all of aoa is built into the
kernel by re-ordering the link order in the Makefile and making the soundbus
use subsys_initcall so it is initialised earlier.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch cleans up the resource handling in i2sbus and adds workarounds for
the broken device trees on the PowerMac7,2 and 7,3. Some of this code will
later move again when macio_asic is going to export all the sub-nodes too.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves the i2sbus 'force' module parameter declaration to the top of
the file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use proper irq mapping interface for snd-aoa-i2sbus.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the new irq remapper core and removes the old one. Because
there are some fundamental conflicts with the old code, like the value
of NO_IRQ which I'm now setting to 0 (as per discussions with Linus),
etc..., this commit also changes the relevant platform and driver code
over to use the new remapper (so as not to cause difficulties later
in bisecting).
This patch removes the old pre-parsing of the open firmware interrupt
tree along with all the bogus assumptions it made to try to renumber
interrupts according to the platform. This is all to be handled by the
new code now.
For the pSeries XICS interrupt controller, a single remapper host is
created for the whole machine regardless of how many interrupt
presentation and source controllers are found, and it's set to match
any device node that isn't a 8259. That works fine on pSeries and
avoids having to deal with some of the complexities of split source
controllers vs. presentation controllers in the pSeries device trees.
The powerpc i8259 PIC driver now always requests the legacy interrupt
range. It also has the feature of being able to match any device node
(including NULL) if passed no device node as an input. That will help
porting over platforms with broken device-trees like Pegasos who don't
have a proper interrupt tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Apparently some firmware versions forget enabling the dual-edge bit,
snd-powermac did that too and even OSX does sometimes. This should fix
headphone plug detection on those machines.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This properly adds support for the iMac G5 iSight.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The dependencies in the soundbus Kconfig were wrong, it isn't
experimental any more.
This patch fixes that and makes it select SND_PCM too instead of
depending on it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This large patch adds all of snd-aoa.
Consisting of many modules, it currently replaces snd-powermac
for all layout-id based machines and handles many more (for
example new powerbooks and powermacs with digital output that
previously couldn't be used at all).
It also has support for all layout-IDs that Apple has (judging
from their Info.plist file) but not all are tested.
The driver currently has 2 known regressions over snd-powermac:
* it doesn't handle powermac 7,2 and 7,3
* it doesn't have a DRC control on snapper-based machines
I will fix those during the 2.6.18 development cycle.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
