Commit Graph

32740 Commits

Author SHA1 Message Date
Vlad Yasevich
a803c94230 sctp: Turn flags in 'sctp_packet' into bit fields
This shrinks the size of sctp_packet a little.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:01 -04:00
Vlad Yasevich
f68b2e05f3 sctp: Fix SCTP_MAXSEG socket option to comply to spec.
We had a bug that we never stored the user-defined value for
MAXSEG when setting the value on an association.  Thus future
PMTU events ended up re-writing the frag point and increasing
it past user limit.  Additionally, when setting the option on
the socket/endpoint, we effect all current associations, which
is against spec.

Now, we store the user 'maxseg' value along with the computed
'frag_point'.  We inherit 'maxseg' from the socket at association
creation and use it as an upper limit for 'frag_point' when its
set.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:00 -04:00
Vlad Yasevich
cb95ea32a4 sctp: Don't do NAGLE delay on large writes that were fragmented small
SCTP will delay the last part of a large write due to NAGLE, if that
part is smaller then MTU.  Since we are doing large writes, we might
as well send the last portion now instead of waiting untill the next
large write happens.  The small portion will be sent as is regardless,
so it's better to not delay it.

This is a result of much discussions with Wei Yongjun <yjwei@cn.fujitsu.com>
and Doug Graham <dgraham@nortel.com>.  Many thanks go out to them.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:59 -04:00
Vlad Yasevich
4d3c46e683 sctp: drop a_rwnd to 0 when receive buffer overflows.
SCTP has a problem that when small chunks are used, it is possible
to exhaust the receiver buffer without fully closing receive window.
This happens due to all overhead that we have account for with small
messages.  To fix this, when receive buffer is exceeded, we'll drop
the window to 0 and save the 'drop' portion.  When application starts
reading data and freeing up recevie buffer space, we'll wait until
we've reached the 'drop' window and then add back this 'drop' one
mtu at a time.  This worked well in testing and under stress produced
rather even recovery.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:59 -04:00
Vlad Yasevich
9c5c62be2f sctp: Send user messages to the lower layer as one
Currenlty, sctp breaks up user messages into fragments and
sends each fragment to the lower layer by itself.  This means
that for each fragment we go all the way down the stack
and back up.  This also discourages bundling of multiple
fragments when they can fit into a sigle packet (ex: due
to user setting a low fragmentation threashold).

We introduce a new command SCTP_CMD_SND_MSG and hand the
whole message down state machine.  The state machine and
the side-effect parser will cork the queue, add all chunks
from the message to the queue, and then un-cork the queue
thus causing the chunks to get transmitted.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:57 -04:00
Vlad Yasevich
bec9640bb0 sctp: Disallow new connection on a closing socket
If a socket has a lot of association that are in the process of
of being closed/aborted, it is possible for a remote to establish
new associations during the time period that the old ones are shutting
down.  If this was a result of a close() call, there will be no socket
and will cause a memory leak.  We'll prevent this by setting the
socket state to CLOSING and disallow new associations when in this state.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:56 -04:00
Rami Rosen
b4e8c6a7e6 sctp: remove unused union (sctp_cmsg_data_t) definition
This patch removes an unused union definition (sctp_cmsg_data_t)
from include/net/sctp/user.h.

Signed-off-by: Rami Rosen <rosenrami@gmail.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:55 -04:00
Wolfgang Grandegger
39e3ab6fde can: add can_free_echo_skb() for upcoming drivers
This patch adds the function can_free_echo_skb to the CAN
device interface to allow upcoming drivers to release echo
skb's in case of error.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-04 02:16:14 -07:00
Wu Fengguang
aa1330766c tcp: replace hard coded GFP_KERNEL with sk_allocation
This fixed a lockdep warning which appeared when doing stress
memory tests over NFS:

	inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.

	page reclaim => nfs_writepage => tcp_sendmsg => lock sk_lock

	mount_root => nfs_root_data => tcp_close => lock sk_lock =>
			tcp_send_fin => alloc_skb_fclone => page reclaim

David raised a concern that if the allocation fails in tcp_send_fin(), and it's
GFP_ATOMIC, we are going to yield() (which sleeps) and loop endlessly waiting
for the allocation to succeed.

But fact is, the original GFP_KERNEL also sleeps. GFP_ATOMIC+yield() looks
weird, but it is no worse the implicit sleep inside GFP_KERNEL. Both could
loop endlessly under memory pressure.

CC: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
CC: David S. Miller <davem@davemloft.net>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 23:45:45 -07:00
Ajit Khaparde
05c6a8d7a7 net/ethtool: Add support for the ethtool feature to flash firmware image from a specified file.
This patch adds support to flash a firmware image to a device using ethtool.
The driver gets the filename of the firmware image and flashes the image
using the request firmware path.

The region "on the chip" to be flashed can be specified by an option.
It is upto the device driver to enumerate the region number passed by ethtool,
to the region to be flashed.

The default behavior is to flash all the regions on the chip.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 23:07:39 -07:00
Eric Dumazet
2e59af3dcb vlan: multiqueue vlan device
vlan devices are currently not multi-queue capable.

We can do that with a new rtnl_link_ops method,
get_tx_queues(), called from rtnl_create_link()

This new method gets num_tx_queues/real_num_tx_queues
from real device.

register_vlan_device() is also handled.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 18:03:00 -07:00
David S. Miller
3f968de276 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 2009-09-02 14:18:09 -07:00
Stephen Hemminger
3b401a81c0 inet: inet_connection_sock_af_ops const
The function block inet_connect_sock_af_ops contains no data
make it constant.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 01:03:49 -07:00
Stephen Hemminger
b2e4b3debc tcp: MD5 operations should be const
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 01:03:43 -07:00
David S. Miller
6cdee2f96a Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/yellowfin.c
2009-09-02 00:32:56 -07:00
David S. Miller
2fbd3da387 pkt_sched: Revert tasklet_hrtimer changes.
These are full of unresolved problems, mainly that conversions don't
work 1-1 from hrtimers to tasklet_hrtimers because unlike hrtimers
tasklets can't be killed from softirq context.

And when a qdisc gets reset, that's exactly what we need to do here.

We'll work this out in the net-next-2.6 tree and if warranted we'll
backport that work to -stable.

This reverts the following 3 changesets:

a2cb6a4dd4
("pkt_sched: Fix bogon in tasklet_hrtimer changes.")

38acce2d79
("pkt_sched: Convert CBQ to tasklet_hrtimer.")

ee5f9757ea
("pkt_sched: Convert qdisc_watchdog to tasklet_hrtimer")

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 17:59:25 -07:00
Stephen Hemminger
89d69d2b75 net: make neigh_ops constant
These tables are never modified at runtime. Move to read-only
section.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 17:40:57 -07:00
Damian Lukowski
5152fc7de3 RTO connection timeout: coding style fixes and comments
This patch affects the retransmits_timed_out() function.

Changes:
1) Variables have more meaningful names
2) retransmits_timed_out() has an introductionary comment.
3) Small coding style changes.

Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 17:40:47 -07:00
Alexey Dobriyan
86393e52c3 netns: embed ip6_dst_ops directly
struct net::ipv6.ip6_dst_ops is separatedly dynamically allocated,
but there is no fundamental reason for it. Embed it directly into
struct netns_ipv6.

For that:
* move struct dst_ops into separate header to fix circular dependencies
	I honestly tried not to, it's pretty impossible to do other way
* drop dynamical allocation, allocate together with netns

For a change, remove struct dst_ops::dst_net, it's deducible
by using container_of() given dst_ops pointer.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 17:40:31 -07:00
Johannes Berg
8bc11b491b rfkill: relicense header file
This header file is copied into userspace tools that
need not be GPLv2 licensed, make that easier.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Iñaky Pérez-González <inaky@linux.intel.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-09-01 12:48:21 -04:00
Damian Lukowski
6fa12c8503 Revert Backoff [v3]: Calculate TCP's connection close threshold as a time value.
RFC 1122 specifies two threshold values R1 and R2 for connection timeouts,
which may represent a number of allowed retransmissions or a timeout value.
Currently linux uses sysctl_tcp_retries{1,2} to specify the thresholds
in number of allowed retransmissions.

For any desired threshold R2 (by means of time) one can specify tcp_retries2
(by means of number of retransmissions) such that TCP will not time out
earlier than R2. This is the case, because the RTO schedule follows a fixed
pattern, namely exponential backoff.

However, the RTO behaviour is not predictable any more if RTO backoffs can be
reverted, as it is the case in the draft
"Make TCP more Robust to Long Connectivity Disruptions"
(http://tools.ietf.org/html/draft-zimmermann-tcp-lcd).

In the worst case TCP would time out a connection after 3.2 seconds, if the
initial RTO equaled MIN_RTO and each backoff has been reverted.

This patch introduces a function retransmits_timed_out(N),
which calculates the timeout of a TCP connection, assuming an initial
RTO of MIN_RTO and N unsuccessful, exponentially backed-off retransmissions.

Whenever timeout decisions are made by comparing the retransmission counter
to some value N, this function can be used, instead.

The meaning of tcp_retries2 will be changed, as many more RTO retransmissions
can occur than the value indicates. However, it yields a timeout which is
similar to the one of an unpatched, exponentially backing off TCP in the same
scenario. As no application could rely on an RTO greater than MIN_RTO, there
should be no risk of a regression.

Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 02:45:47 -07:00
Damian Lukowski
f1ecd5d9e7 Revert Backoff [v3]: Revert RTO on ICMP destination unreachable
Here, an ICMP host/network unreachable message, whose payload fits to
TCP's SND.UNA, is taken as an indication that the RTO retransmission has
not been lost due to congestion, but because of a route failure
somewhere along the path.
With true congestion, a router won't trigger such a message and the
patched TCP will operate as standard TCP.

This patch reverts one RTO backoff, if an ICMP host/network unreachable
message, whose payload fits to TCP's SND.UNA, arrives.
Based on the new RTO, the retransmission timer is reset to reflect the
remaining time, or - if the revert clocked out the timer - a retransmission
is sent out immediately.
Backoffs are only reverted, if TCP is in RTO loss recovery, i.e. if
there have been retransmissions and reversible backoffs, already.

Changes from v2:
1) Renaming of skb in tcp_v4_err() moved to another patch.
2) Reintroduced tcp_bound_rto() and __tcp_set_rto().
3) Fixed code comments.

Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 02:45:42 -07:00
Yi Zou
7114323b17 dcbnl: Add support for setapp/getapp to netdev dcbnl_rtnl_ops
Adds support of dcbnl setapp/getapp to dcbnl_rtnl_ops in netdev to allow
LLDs to implement their corresponding dcbnl setapp/getapp ops to support
the IEEE 802.1Q DCBX setapp/getapp commands.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 01:24:30 -07:00
Yi Zou
0f6f290259 dcbnl: Add support for setapp/getapp commands to dcbnl
This patch adds dcbnl command definitions to support setapp/getapp
functionality from the IEEE 802.1Qaz Data Center Bridging Capability
Exchange protocol (DCBX) specification. Section 3.3 defines the
application protocol and its 802.1p user priority in DCBX, which is
implemented here as a pair of setapp/getapp commands in the kernel
dcbnl for setting and retrieving the user priority for an given
application protocol. The protocol is identified by the combination of
an id and an idtype. Currently, when idtype is 0, the corresponding
id gives the ether type of this protocol, e.g., for FCoE, it will be
0x8906; when idtype is 1, then the corresponding id gives the TCP or
UDP port number.

For more information regarding DCBX spec., please refer to the following:
http://www.ieee802.org/1/files/public/docs2008/
az-wadekar-dcbx-capability-exchange-discovery-protocol-1108-v1.01.pdf

Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 01:24:30 -07:00
Yi Zou
cb45439977 net: Add ndo_fcoe_enable/ndo_fcoe_disable to net_device_ops
Add ndo_fcoe_enable/_disable to net_device_ops so the corresponding
HW can initialize itself for FCoE traffic or clean up after FCoE traffic is
done. This is expected to be called by the kernel FCoE stack upon receiving
a request for creating an FCoE instance on the corresponding netdev interface.
When implemented by the actual HW, the HW driver check the op code to perform
corresponding initialization or clean up for FCoE. The initialization normally
includes allocating extra queues for FCoE, setting corresponding HW registers
for FCoE, indicating FCoE offload features via netdev, etc. The clean-up would
include releasing the resources allocated for FCoE.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 01:24:20 -07:00
Stephen Hemminger
61357325f3 netdev: convert bulk of drivers to netdev_tx_t
In a couple of cases collapse some extra code like:
   int retval = NETDEV_TX_OK;
   ...
   return retval;
into
   return NETDEV_TX_OK;

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 01:14:07 -07:00
Stephen Hemminger
4c5d502d8b hdlc: convert to netdev_tx_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 01:13:31 -07:00
Stephen Hemminger
25a79c41ce usbnet: convert to netdev_tx_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 01:13:22 -07:00
Stephen Hemminger
dc1f8bf68b netdev: change transmit to limited range type
The transmit function should only return one of three possible values,
some drivers got confused and returned errno's or other values.
This changes the definition so that this can be caught at compile time.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 01:13:03 -07:00
Krishna Kumar
7b3d3e4fc6 netdevice: Consolidate to use existing macros where available.
Patch compiled and 32 simultaneous netperf testing ran fine.

Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-30 22:16:20 -07:00
David S. Miller
b9caaabb99 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluetooth-next-2.6 2009-08-30 21:30:39 -07:00
Matt Carlson
2befdcea96 tg3: Add new 5785 10/100 only device ID
This patch adds a new device ID for those 5785 devices that will only
use 10/100 phys.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29 15:42:31 -07:00
Eric Dumazet
df19a62677 tcp: keepalive cleanups
Introduce keepalive_probes(tp) helper, and use it, like 
keepalive_time_when(tp) and keepalive_intvl_when(tp)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28 23:48:54 -07:00
Gábor Stefanik
06e4da268c ssb: Implement PMU LDO control and use it in b43
Implement the "PMU LDO set voltage" and "PMU LDO PA ref enable"
functions, and use them during LP-PHY baseband init in b43.

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28 14:40:53 -04:00
John W. Linville
103bf9f7d3 mac80211: remove ieee80211_rx namespace hack
With the libipw naming scheme change, it is no longer necessary for
mac80211 to avoid the ieee80211_rx name clash.

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28 14:40:29 -04:00
John W. Linville
b0a4e7d8a2 libipw: switch from ieee80211_* to libipw_* naming policy
This eliminates the dual definition of ieee80211_channel (and possibly
others), further clarifying who defines what and paving the way for
inclusion of cfg80211.h.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28 14:40:28 -04:00
Javier Cardona
9e03fdfd05 mac80211: Update mesh config IE to 11s draft 3.02
The mesh config information element has changed significantly since draft 1.08
This patch brings it up to date.

Thanks to Sam Leffler and Rui Paulo for identifying this.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28 14:40:24 -04:00
Gustavo F. Padovan
2246b2f1b4 Bluetooth: Handle L2CAP case when the remote receiver is busy
Implement all issues related to RemoteBusy in the RECV state table.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-26 00:12:20 -07:00
David S. Miller
9409172262 Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/lowpan/lowpan 2009-08-23 19:19:30 -07:00
Andy Grover
70041088e3 RDS: Add TCP transport to RDS
This code allows RDS to be tunneled over a TCP connection.

RDMA operations are disabled when using TCP transport,
but this frees RDS from the IB/RDMA stack dependency, and allows
it to be used with standard Ethernet adapters, or in a VM.

Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-23 19:13:02 -07:00
David S. Miller
ee5f9757ea pkt_sched: Convert qdisc_watchdog to tasklet_hrtimer
None of this stuff should execute in hw IRQ context, therefore
use a tasklet_hrtimer so that it runs in softirq context.

Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
2009-08-22 18:09:17 -07:00
Luiz Augusto von Dentz
9e726b1742 Bluetooth: Fix rejected connection not disconnecting ACL link
When using DEFER_SETUP on a RFCOMM socket, a SABM frame triggers
authorization which when rejected send a DM response. This is fine
according to the RFCOMM spec:

    the responding implementation may replace the "proper" response
    on the Multiplexer Control channel with a DM frame, sent on the
    referenced DLCI to indicate that the DLCI is not open, and that
    the responder would not grant a request to open it later either.

But some stacks doesn't seems to cope with this leaving DLCI 0 open after
receiving DM frame.

To fix it properly a timer was introduced to rfcomm_session which is used
to set a timeout when the last active DLC of a session is unlinked, this
will give the remote stack some time to reply with a proper DISC frame on
DLCI 0 avoiding both sides sending DISC to each other on stacks that
follow the specification and taking care of those who don't by taking
down DLCI 0.

Signed-off-by: Luiz Augusto von Dentz <luiz.dentz@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 15:05:58 -07:00
Gustavo F. Padovan
ef54fd937f Bluetooth: Full support for receiving L2CAP SREJ frames
Support for receiving of SREJ frames as specified by the state table.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 15:03:43 -07:00
Gustavo F. Padovan
8f17154f1f Bluetooth: Add support for L2CAP SREJ exception
When L2CAP loses an I-frame we send a SREJ frame to the transmitter side
requesting the lost packet. This patch implement all Recv I-frame events
on SREJ_SENT state table except the ones that deal with SendRej (the REJ
exception at receiver side is yet not implemented).

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 15:01:25 -07:00
Gustavo F. Padovan
fcc203c30d Bluetooth: Add support for FCS option to L2CAP
Implement CRC16 check for L2CAP packets. FCS is used by Streaming Mode and
Enhanced Retransmission Mode and is a extra check for the packet content.

Using CRC16 is the default, L2CAP won't use FCS only when both side send
a "No FCS" request.

Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:59:49 -07:00
Gustavo F. Padovan
e90bac061b Bluetooth: Add support for Retransmission and Monitor Timers
L2CAP uses retransmission and monitor timers to inquiry the other side
about unacked I-frames. After sending each I-frame we (re)start the
retransmission timer. If it expires, we start a monitor timer that send a
S-frame with P bit set and wait for S-frame with F bit set. If monitor
timer expires, try again, at a maximum of L2CAP_DEFAULT_MAX_TX.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:56:15 -07:00
Gustavo F. Padovan
30afb5b2aa Bluetooth: Initial support for retransmission of packets with REJ frames
When receiving an I-frame with unexpected txSeq, receiver side start the
recovery procedure by sending a REJ S-frame to the transmitter side. So
the transmitter can re-send the lost I-frame.

This patch just adds a basic support for retransmission, it doesn't
mean that ERTM now has full support for packet retransmission.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:55:20 -07:00
Gustavo F. Padovan
c74e560cd0 Bluetooth: Add support for Segmentation and Reassembly of SDUs
ERTM should use Segmentation and Reassembly to break down a SDU in many
PDUs on sending data to the other side.

On sending packets we queue all 'segments' until end of segmentation and
just the add them to the queue for sending. On receiving we create a new
SKB with the SDU reassembled.

Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:53:58 -07:00
Gustavo F. Padovan
1c2acffb76 Bluetooth: Add initial support for ERTM packets transfers
This patch adds support for ERTM transfers, without retransmission, with
txWindow up to 63 and with acknowledgement of packets received. Now the
packets are queued before call l2cap_do_send(), so packets couldn't be
sent at the time we call l2cap_sock_sendmsg(). They will be sent in
an asynchronous way on later calls of l2cap_ertm_send(). Besides if an
error occurs on calling l2cap_do_send() we disconnect the channel.

Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:53:01 -07:00
Gustavo F. Padovan
f2fcfcd670 Bluetooth: Add configuration support for ERTM and Streaming mode
Add support to config_req and config_rsp to configure ERTM and Streaming
mode. If the remote device specifies ERTM or Streaming mode, then the
same mode is proposed. Otherwise ERTM or Basic mode is used. And in case
of a state 2 device, the remote device should propose the same mode. If
not, then the channel gets disconnected.

Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:50:07 -07:00