Alan has noticed that distros always enabled burst mode
(+ datasheet confirms that it is the right thing to do).
Thus fix pdc202xx_old host driver to do it unconditionally
and remove no longer needed CONFIG_PDC202XX_BURST option.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove stale comment from the cs5520 IDE driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
with module_param macro, the __setup code can be killed now:
const __setup("all-generic-ide", ide_generic_all_on);
and the module name "generic.ko" is not descriptive to its functionality,
can be changed in Makefile, the "ide-pci-generic.ko" is better.
the ide-pci-generic.all-generic-ide parameter also documented
in Documentation/kernel-parameters.txt
Signed-off-by: Denis Cheng <crquan@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* siimage.c: use hwif->sata_scr[SATA_{ERROR,STATUS}_OFFSET] instead of
SATA_{ERROR,STATUS}_REG macros.
* Remove no longer needed SATA_*_REG macros.
While at it:
* Remove needless SATA Status register read from sil_sata_reset_poll().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->port_init_devs method to ide_hwif_t for a host specific
initialization of devices on a port. Call the new method from
ide_port_init_devices().
* Convert ht6560b, qd65xx and opti621 host drivers to use the new
->port_init_devs method.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use the same bit for IDE_HFLAG_CS5520 and IDE_HFLAG_VDMA host flags
(both are used only by cs5520 host driver currently).
* Add IDE_HFLAG_NO_IO32_BIT host flag and use it instead of ->no_io_32bit
ide_hwif_t field.
* Add IDE_HFLAG_NO_UNMASK_IRQS host flag, then convert dtc2278 and rz1000
host drivers to use it.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
bast-ide.c/ide-cs.c/delkin_cb.c:
* Don't set 'restore' flag for ide_unregister() when initializing new
interface.
rapide.c/ide-pnp.c/ide-cs.c/ide_platform.c/au1xxx-ide.c/delkin_cb.c/scc_pata.c:
* Don't set 'init_default' and 'restore' flags for ide_unregister() when
removing interface.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out code for finding ide_hwifs[] slot from ide_register_hw()
to ide_deprecated_find_port().
* Convert bast-ide, ide-cs and delkin_cb host drivers to use ide_device_add()
instead of ide_register_hw() (while at it drop doing "ide_unregister()" loop
which tries to unregister _all_ IDE interfaces if useable ide_hwifs[] slot
cannot be find).
This patch leaves us with only two ide_register_hw() users:
- drivers/macintosh/mediabay.c
- drivers/ide/ide.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'init_default' (flag for calling init_hwif_default()) and 'restore'
(flag for calling ide_hwif_restore()) arguments to ide_unregister().
* Update ide_unregister() users to set 'init_default' and 'restore' flags.
* No need to set 'init_default' flag in ide_register_hw() if the setup done
by init_hwif_default() is going to be overridden by ide_init_port_hw().
* No need to set 'init_default' and 'restore' flags in cleanup_module().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->cable_detect method to ide_hwif_t.
* Call the new method in ide_init_port() if:
- the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
- DMA initialization was successful (if hwif->dma_base is not set
ide_init_port() sets hwif->ultra_mask to zero)
- "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')
* Convert PCI host drivers to use ->cable_detect method.
While at it:
* Factor out cable detection to separate functions (if not already done).
* hpt366.c/it8213.c/slc90e66.c:
- don't check cable type if "idex=ata66" is used
* pdc202xx_new.c:
- add __devinit tag to pdcnew_cable_detect()
* pdc202xx_old.c:
- rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
- add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove 'struct pci_dev *dev' argument from ide_hwif_setup_dma().
* Un-static ide_hwif_setup_dma() and add CONFIG_BLK_DEV_IDEDMA_PCI=n version.
* Add 'const struct ide_port_info *d' argument to ide_device_add[_all]().
* Factor out generic ports init from ide_pci_setup_ports() to ide_init_port(),
move it to ide-probe.c and call it in in ide_device_add_all() instead of
ide_pci_setup_ports().
* Move ->mate setup to ide_device_add_all() from ide_port_init().
* Add IDE_HFLAG_NO_AUTOTUNE host flag for host drivers that don't enable
->autotune currently.
* Setup hwif->chipset in ide_init_port() but iff pi->chipset is set
(to not override setup done by ide_hwif_configure()).
* Add ETRAX host handling to ide_device_add_all().
* cmd640.c: set IDE_HFLAG_ABUSE_* also for CONFIG_BLK_DEV_CMD640_ENHANCED=n.
* pmac.c: make pmac_ide_setup_dma() return an error value and move DMA masks
setup to pmac_ide_setup_device().
* Add 'struct ide_port_info' instances to legacy host drivers, pass them to
ide_device_add() calls and then remove open-coded ports initialization.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't override the cable type if the "idex=ata66" parameter was used.
While at it:
* atiixp.c: factor out cable detection to atiixp_cable_detect() from
init_hwif_atiixp().
* cs5535.c: pass 'ide_hwif_t *hwif' instead of 'struct pci_dev *dev' to
cs5535_cable_detect().
* scc_pata.c: factor out cable detection to scc_cable_detect() from
init_hwif_scc() and remove incorrect comment.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
PCI: make pci_bus a struct device
PCI: fix codingstyle issues in include/linux/pci.h
PCI: fix codingstyle issues in drivers/pci/pci.h
PCI: PCIE ASPM support
PCI: Fix fakephp deadlock
PCI: modify SB700 SATA MSI quirk
PCI: Run ACPI _OSC method on root bridges only
PCI ACPI: AER driver should only register PCIe devices with _OSC
PCI ACPI: Added a function to register _OSC with only PCIe devices.
PCI: constify function pointer tables
PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
pciehp: block new requests from the device before power off
pciehp: workaround against Bad DLLP during power off
pciehp: wait for 1000ms before LED operation after power off
PCI: Remove pci_enable_device_bars() from documentation
PCI: Remove pci_enable_device_bars()
PCI: Remove users of pci_enable_device_bars()
PCI: Add pci_enable_device_{io,mem} intefaces
PCI: avoid save the same type of cap multiple times
PCI: correctly initialize a structure for pcie_save_pcix_state()
...
This patch converts users of pci_enable_device_bars() to the new
pci_enable_device_{io,mem} interface.
The new API fits nicely, except maybe for the QLA case where a bit of
code re-organization might be a good idea but I prefer sticking to the
simple patch as I don't have hardware to test on.
I'll also need some feedback on the cs5520 change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make probe_hwif() return an error value.
While at it:
* Remove comment about MAX_DRIVES == 2 limitation (it is not special to
probe_hwif(), it is a general assumption taken by a lot of IDE code).
* Rename probe_hwif() to ide_probe_port().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Delete filenames/versions from comments.
I'm leaving decisions about adding DRV_VERSION defines and MODULE_VERSION()-s
to maintainers of the respective drivers.
While at it:
* Remove unused VERSION define from ide.c.
* Remove unused/stale DRV_VERSION define from au1xxx-ide.c.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Keep pointer to struct device instead of struct pci_dev in ide_hwif_t.
While on it:
* Use *dev->dma_mask instead of pci_dev->dma_mask in ide_toggle_bounce().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_destroy_dmatable() in:
* ide-dma.c::ide_build_dmatable()
* sgiioc4.c::sgiioc4_build_dma_table()
* pmac.c::pmac_ide_{build,destroy}_dmatable()
There should be no functionality changes caused by this patch.
v2:
* pmac.c build fix from Andrew Morton.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_NO_DSC host flag for hosts that doesn't support DSC overlap.
* Set it in aec62xx (for ATP850UF only) and hpt34x host drivers.
* Convert ide-tape device driver to check for IDE_HFLAG_NO_DSC flag.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename 'simplex_stat' variable to 'dma_stat' in ide_get_or_set_dma_base().
* Factor out code for forcing host out of "simplex" mode from
ide_get_or_set_dma_base() to ide_pci_clear_simplex() helper.
* Add IDE_HFLAG_CLEAR_SIMPLEX host flag and set it in alim15x3 (for M5229),
amd74xx (for AMD 7409), cmd64x (for CMD643), generic (for Netcell) and
serverworks (for CSB5) host drivers.
* Make ide_get_or_set_dma_base() test for IDE_HFLAG_CLEAR_SIMPLEX host flag
instead of checking dev->device (BTW the code was buggy because it didn't
check for dev->vendor, luckily none of these PCI Device IDs was used by
some other vendor for PCI IDE controller).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer needed assertion from amd74xx_probe().
* Factor out cable detection for AMD7409 to amd7409_cable_detect() and for
chipsets >= AMD7411 to amd7411_cable_detect().
* Use dev->vendor and dev->device instead of amd_config->udma_mask when
selecting cable detection method and checking for broken FIFO support in
init_chipset_amd74xx().
* Remove no longer needed AMD_BAD_FIFO define.
* Add 'swdma' parameter for setting .swdma_mask to DECLARE_AMD_DEV() macro.
* Add 'udma' parameter for setting .udma_mask to DECLARE_{AMD,NV}_DEV() macro.
* Keep a copy of a current amd74xx_chipsets[] entry in amd74xx_probe()
in order to fix ->swdma_mask on early AMD7409 revisions and ->udma_mask
on Serenade mainboards.
* Remove no longer needed fixups from init_chipset_amd74xx()
and AMD_CHECK_{SWDMA,SERENADE} defines.
* Move printing banner message from init_chipset_amd74xx() to amd74xx_probe(),
also remove incorrect comment while at it.
* Use hwif->ultra_mask instead of amd_config->udma_mask in amd_set_drive().
* Add 'udma_mask' argument to amd_set_speed() and pass UDMA mask from
amd_set_drive() instead of using amd_config->udma_mask.
* Move amd_config->base from AMD_* defines to users of these defines and add
0x40 the defined values. Then add amd_offset() inline helper for selecting
offset from 0x40 base (needed for nVidia controllers) and finally use it in
amd_set_speed(), amd7411_cable_detect() and init_chipset_amd74xx() instead
of amd_config->base.
* Remove no longer needed AMD_BAD_SWDMA define, ->{swdma,ultra}_mask setup
from init_hwif_amd74xx(), amd_{config,chipset} variables and amd_ide_chips
table.
* Fix init_chipset_amd74xx() comment.
* Bump driver version.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
According to http://marc.info/?l=linux-ide&m=114346138611631, the drivers must
always register 8 DMA ports with ide_setup_dma(), so its last argument is not
needed. While at it, kill some useless parens in that function...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The TRM-290 chip is *not* SFF-8038i compatible and therefore can *not* call
ide_setup_dma() -- fix this and also cleanup the code a bit...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This belongs to user-space (and only if really needed).
text data bss dec hex filename
3874 180 28 4082 ff2 drivers/ide/pci/cmd64x.o.before
2231 180 0 2411 96b drivers/ide/pci/cmd64x.o.after
Additionaly to being bloat the code reported incorrect UDMA modes for
the reserved values of UDIDETCR0/1 registers.
Also while at it remove unused CNTRL_DIS_RA0/1 defines.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make remaining built-in only IDE host drivers modular, add ide-scan-pci.c
file for probing PCI host drivers registered with IDE core (special case
for built-in IDE and CONFIG_IDEPCI_PCIBUS_ORDER=y) and then take care of
the ordering in which all IDE host drivers are probed when IDE is built-in
during link time.
* Move probing of gayle, falconide, macide, q40ide and buddha (m68k arch
specific) host drivers, before PCI ones (no PCI on m68k), ide-cris (cris
arch specific), cmd640 (x86 arch specific) and pmac (ppc arch specific).
* Move probing of ide-cris (cris arch specific) host driver before cmd640
(x86 arch specific).
* Move probing of mpc8xx (ppc specific) host driver before ide-pnp (depends
on ISA and none of ppc platform that use mpc8xx supports ISA) and ide-h8300
(h8300 arch specific).
* Add "probe_vlb" kernel parameter to cmd640 host driver and update
Documentation/ide.txt accordingly.
* Make IDE_ARM config option visible so it can also be disabled if needed.
* Remove bogus comment from ide.c while at it.
v2:
* Fix two issues spotted by Sergei:
- replace ENOMEM error value by ENOENT in ide-h8300 host driver
- fix MODULE_PARM_DESC() in cmd640 host driver
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add mpc8xx_ide_probe() to mpc8xx.c and call it from probe_for_hwifs().
* Convert ide_arm, ide-cris, ide-h8300, ide-pnp, buddha, falconide, gayle,
macide, q40ide, cmd640 and mpc8xx host drivers to use ide_device_add().
This removes dependency on ide_generic for these drivers so update
ide/Kconfig accordingly.
v2:
* ide_arm build fix (s/ide_device_idx/ide_device_add/)
(Thanks to Christoph Lameter <clameter@sgi.com> for reporting the problem).
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename init_hwif_data() to ide_init_port_data() and export it.
* For all users of ide_register_hw() with 'initializing' argument set
hwif->present and hwif->hold are always zero so convert these host
drivers to use ide_find_port()+ide_init_port_data()+ide_init_port_hw()
instead (also no need for init_hwif_default() call since the setup
done by it gets over-ridden by ide_init_port_hw() call).
* Drop 'initializing' argument from ide_register_hw().
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_init_port_hw() helper.
* rapide.c: convert rapide_locate_hwif() to rapide_setup_ports()
and use ide_init_port_hw().
* ide_platform.c: convert plat_ide_locate_hwif() to plat_ide_setup_ports()
and use ide_init_port_hw().
* sgiioc4.c: use ide_init_port_hw().
* pmac.c: add 'hw_regs_t *hw' argument to pmac_ide_setup_device(),
setup 'hw' in pmac_ide_{macio,pci}_attach() and use ide_init_port_hw()
in pmac_ide_setup_device().
This patch is a preparation for the future changes in the IDE probing code.
There should be no functionality changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Assign drive->quirk_list in ->quirkproc implementations:
- hpt366.c::hpt3xx_quirkproc()
- pdc202xx_new.c::pdcnew_quirkproc()
- pdc202xx_old.c::pdc202xx_quirkproc()
* Make ->quirkproc void.
* Move calling ->quirkproc from do_identify() to probe_hwif().
* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.
* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
no longer needed drive->present check from is_dev_seagate_sata().
* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
as an argument. Then convert ide_register_hw() to accept 'quirkproc'
argument instead of 'fixup' one.
* Remove no longer needed ->fixup method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge ->dma_host_{on,off} methods into ->dma_host_set method
which takes 'int on' argument.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_dma_off_quietly() and __ide_dma_on() always available.
* Drop "__" prefix from __ide_dma_on().
* Check for presence of ->dma_host_on instead of ->ide_dma_on.
* Convert all users of ->ide_dma_on and ->dma_off_quietly methods
to use ide_dma_on() and ide_dma_off_quietly() instead.
* Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods
from ide_hwif_t.
* Make ide_dma_on() void.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().
Tested on Altix by Jeremy.
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix SWDMA/MWDMA masks in cy82c693_chipset.
* Add IDE_HFLAG_CY82C693 host flag and use it in ide_tune_dma() to
check whether the DMA should be enabled even if ide_max_dma_mode()
fails.
* Convert cy82c693_dma_enable() to become cy82c693_set_dma_mode()
and remove no longer needed cy82c693_ide_dma_on(). Then set
IDE_HFLAG_CY82C693 instead of IDE_HFLAG_TRUST_BIOS_FOR_DMA in
cy82c693_chipset.
* Bump driver version.
As a result of this patch cy82c693 driver will configure and use DMA on
all SWDMA0-2 and MWDMA0-2 capable ATA devices instead of relying on BIOS.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Mask device DMA masks by ATA_{S,M}WDMA2 in cy82c693_ide_dma_on().
* Remove clipping of DMA modes by id->tDMA in cy82c693_dma_enable():
- id->tDMA may not be defined on newer devices
- id->vendor6/id->tDMA word is in LE endianness
(cy82c693 seems to be Alpha specific though)
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set the correct hwif->dma_base for the second channel in
ide_get_or_set_dma_base().
* Remove DMA enable code from cs5520_set_pio_mode(), this can
be handled by the generic ->dma_host_on method now.
* Add VDMA check to ide_config_drive_speed().
* drive->using_dma was never enabled since cs5520 host driver's
->ide_dma_on method overrided the generic ->ide_dma_on (so
__ide_dma_on() was never called, drive->using_dma was never set
and VDMA was never used since it depends on drive->using_dma).
Fix it by using ->dma_host_on method instead of ->ide_dma_on
(also add matching ->dma_host_off method).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
IDE core guarantees that ->set_dma_mode will be called only
for DMA modes set in SWDMA/MWDMA/UDMA masks.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Program register 0x40 in sl82c105_resetproc().
* Remove no longer needed sl82c105_selectproc() and pci_set_drvdata() calls.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Program DMA timings in sl82c105_dma_start() (->dma_start method)
before starting DMA transfer.
* Add sl82c105_dma_end() (->ide_dma_end method) to switch back to
PIO timings when DMA transfer is complete.
* In sl82c105_set_pio_mode() program timings regardless of ->using_dma
setting and in sl82c105_set_dma_mode() only cache the new timings.
* Remove no longer needed sl82c105_{ide_dma_on,off_quietly}().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on pata_sc1200.c.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_ABUSE_SET_DMA_MODE host flag and use it to decide
what to do with transfer modes < XFER_PIO_0 in ide_set_xfer_rate().
* Set IDE_HFLAG_ABUSE_SET_DMA_MODE in host drivers that need it
(aec62xx, amd74xx, cs5520, cs5535, hpt34x, hpt366, pdc202xx_old,
serverworks, tc86c001 and via82cxxx) and cleanup ->set_dma_mode
methods in host drivers that don't (IDE core code guarantees that
->set_dma_mode will be called only for modes which are present
in SWDMA/MWDMA/UDMA masks).
While at it:
* Add IDE_HFLAGS_HPT34X/HPT3XX/PDC202XX/SVWKS define in
hpt34x/hpt366/pdc202xx_old/serverworks host driver.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out UDMA programming code from sis_set_dma_mode() to per
chipset family helpers: sis_{ata33,ata133}_program_udma_timings().
* Add sis_program_udma_timings() helper.
* Remove unneeded casts to 'unsigned long'.
* Minor cleanups.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move PIO programming code from pdcnew_set_mode() to pdcnew_set_pio_mode().
* Rename pdcnew_set_mode() to pdcnew_set_dma_mode().
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Save PCI regs values for both IDE ports in one buffer, in order to eliminate
a needless and ugly loop across all hwifs, searching for our PCI device.
Partially based on the previous patch by Jeff Garzik.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Given that:
* hpt366.c::hpt3xx_intrproc() is the only user of hwif->intrproc
* hpt366.c::hpt3xx_quirkproc() sets drive->quirk_list to 1 for quirky drives
which is a value unique to hpt366 host driver
we can remove hwif->intproc and just check for drive->quirk_list == 1
in ide_do_request().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert cmd64x, hpt366 and pdc202xx_old host drivers to use
pci_resource_start(hwif->pci_dev, 4) instead of hwif->dma_master.
* Remove no longer needed ->dma_master field from ide_hwif_t.
v2:
* Use the more readable 'hwif->dma_base - (hwif->channel * 8)' instead of
pci_resource_start(hwif->pci_dev, 4).
v3:
* Use hwif->extra_base in hpt366/pdc20xx_old + some cosmetic fixups over v2
(suggested by Sergei).
v4:
* Correct offsets in hpt3xxn_set_clock().
v5:
* Use hwif->extra_base in hpt366 for _real_ this time. (Noticed by Sergei)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Group the array of pointers to the timing tables with the timing register masks
which allows us to merge HPT36x/HPT37x set_dma_mode() methods into one.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There's no reason to keep the set_dma_mode() method wrapper for two different
chip families, so get rid of it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since PIO autotuning is now done always, there's no need anymore to program
the taskfile timings also on DMA modes, so change the IDE timing register
masks accordingly, "inverting the polarity" of the masks while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Using default methods caused the chip's DMA PRD count registers, inadvertently
starting DMA! While fixing it, also do:
- get rid of the 'ide_' prefixes in several functions for which the prefix in
the method's name has been 'ide_' ectomized already;
- align the code hooking the IDE DMA methods in init_hwif_trm290()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 528a572dae ("ide: add ->chipset field
to ide_pci_device_t") broke hwif->chipset setup (it is now set to ide_cmd646
for CMD648 instead of CMD646). It seems that the breakage happend while
I was moving patches around (cmd64x_chipsets[] entries for CMD646 and CMD648
are identical except for 'name' field). Fix it and bump driver version.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
After looking into the HPT370 manual (now that I have it) and re-checking all
the timing tables, here's what I have discovered:
- at 33 MHz clock, PIO mode 0 timings turned to be overclocked, and all other
PIO modes underclocked;
- at 50 MHz clock, PIO modes 0 to 2 turned to be overclocked;
- at 66 MHz clock, PIO mode 0 was overclocked too.
Finally, the taskfile timing (matching PIO mode 0) turned to be overclocked at
all clock frequencies (and in all manuals)...
The new timings have been tested on HPT370 chip (at 33 MHz PCI clock) and on
HPT371N chip (at both 50 and 66 MHz DPLL clock).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In case of Promise TX4 the first PCI device is located at slot 1
and the second one is at slot 2 so the offset used by pci_get_slot()
should be "+1" and not "+2".
Thanks goes out to Markus Dietz for bugreport and testing this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Port of Jeff's libata commit 54174db300
("[libata] ata_piix: add HP compaq laptop to short cable list").
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Port of Alan's patch for pata_ali.c.
Cc: Alan Cox <alan@redhat.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add pci_enable_device() to aec62xx probe function
before doing any I/O.
Original probe function tries to read from device's
PCI region 4 before calling ide_setup_pci_device().
Since the device is not enabled at this point,
on machines that have no firmware PCI initialization
(e.g. ASUS WL-700gE router), corresponding PCI BAR
is 0 and the following inb() causes a kernel oops.
Signed-off-by: Aleksandar Radovanovic <biblbroks@sezampro.yu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The intent behind siimage_reset() was probably to hard reset the interface and
the SATA PHY but as the code writes to two reserved bits instead, it obviously
has been ineffective from the start. So, just remove it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
With newer kernels HDD in my old laptop is limited to UDMA 33.
With this patch I get UDMA 100 again.
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix ide-cris, cs5530, sc1200 and sis5513 host drivers to just return instead
of OOPS-ing for unsupported modes in ->set_dma_mode methods.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make sure to not clear the other IDE channel's interrupt when clearing an IDE
interrupt via the MRDMODE register.
Thanks to Bart for finding a coding mistake.
Bart:
This fixes regression from commit 66602c83dc
("cmd64x: use interrupt status from MRDMODE register (take 2)").
Extra thanks to Martin for reporting and bisecting the issue.
From: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Tested-by: Martin Rogge <marogge@onlinehome.de>
Tested-by: Milan Kocian <milon@wq.cz>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In piix.c (and in ata_piix.c) are already included some patches to skip the
cable check on some laptops and to enable UDMA > 33 modes, but I've noticed
than theese doesn't work on my Acer Aspire 5602WLMi (maybe exist more
versions of this laptop). With this simple patch I can set transfer mode
to UDMA100.
From: "sebdeg@ngi.it" <sebdeg@ngi.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* We shouldn't bother with dev->current_state, the PCI API functions we
call manage this for us (and do a far better job at it too).
* Remove pci_set_power_state(dev, PCI_D0) call in resume, as
pci_enable_device() does the same thing.
* Check pci_enable_device() return value. If it failed, fail
the entire resume and avoid programming timings into the [potentially
dead/asleep] chip.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently
and that generic IDE PCI host driver is also affected by the same issue:
On Thursday 25 October 2007, Ralf Baechle wrote:
> CC drivers/ide/pci/generic.o
> drivers/ide/pci/generic.c:52: error: __setup_str_ide_generic_all_on causes a
> +section type conflict
[ Also reported by Martijn Uffing <mp3project@sarijopen.student.utwente.nl>. ]
This patch workarounds the problem in a bit hackish way but without
removing const from generic_chipsets[] (it adds const to __setup() so
__setup_str_ide_generic_all becomes const).
Now all __{dev}initdata data in generic IDE PCI host driver are read-only
so it builds again (driver's .init.data section gets marked as READONLY).
Cc: Martijn Uffing <mp3project@sarijopen.student.utwente.nl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Saturday 20 October 2007, Avuton Olrich wrote:
> My randconfig script the attached config caught an error on:
> drivers/ide/pci/cy82c693.c:439: error: primary causes a section type conflict
>
> My git tree: c00046c279
>
> Bisected to:
> 8562043606 is first bad commit
> commit 8562043606
> Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Date: Sat Oct 20 00:32:34 2007 +0200
>
> ide: constify struct ide_port_info
>
> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently
and that hpt366 host driver is also affected by the same issue:
> drivers/ide/pci/hpt366.c:1428: error: hpt366_chipsets causes a section type
> conflict
This patch workarounds the problem by making static struct hpt_info instances
const. Now all __devinitdata data in hpt366 host driver are read-only so it
builds again (driver's .init.data section gets marked as READONLY).
While at it:
* Bump driver version.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: "Avuton Olrich" <avuton@gmail.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Saturday 20 October 2007, Avuton Olrich wrote:
> My randconfig script the attached config caught an error on:
> drivers/ide/pci/cy82c693.c:439: error: primary causes a section type conflict
>
> My git tree: c00046c279
>
> Bisected to:
> 8562043606 is first bad commit
> commit 8562043606
> Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> Date: Sat Oct 20 00:32:34 2007 +0200
>
> ide: constify struct ide_port_info
>
> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out that const and __{dev}initdata cannot be mixed currently.
This patch workarounds the problem by removing __devinitdata tag from 'primary'
variable (which makes 'primary' to be moved from .init.data to .bss section).
Now all __devinitdata data in cy82c693 host driver are read-only so it builds
again (driver's .init.data section gets marked as READONLY).
While at it:
* Move 'primary' variable to its only user, init_iops_cy82c693().
* Bump driver version.
Cc: "Avuton Olrich" <avuton@gmail.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (74 commits)
fix do_sys_open() prototype
sysfs: trivial: fix sysfs_create_file kerneldoc spelling mistake
Documentation: Fix typo in SubmitChecklist.
Typo: depricated -> deprecated
Add missing profile=kvm option to Documentation/kernel-parameters.txt
fix typo about TBI in e1000 comment
proc.txt: Add /proc/stat field
small documentation fixes
Fix compiler warning in smount example program from sharedsubtree.txt
docs/sysfs: add missing word to sysfs attribute explanation
documentation/ext3: grammar fixes
Documentation/java.txt: typo and grammar fixes
Documentation/filesystems/vfs.txt: typo fix
include/asm-*/system.h: remove unused set_rmb(), set_wmb() macros
trivial copy_data_pages() tidy up
Fix typo in arch/x86/kernel/tsc_32.c
file link fix for Pegasus USB net driver help
remove unused return within void return function
Typo fixes retrun -> return
x86 hpet.h: remove broken links
...
Take ide_lock for prefetch disable/enable in do_special(),
then cleanup cmd640 and ht6560b host drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Stop abusing ide_lock lock (switch to a private locking).
Fixes same issue as fixed by Alan Cox in atiixp host driver with
commit 6c5f8cc33e.
cmd640 is a bit special cause we still need to leave ide_lock for
->set_pio_mode with 'pio' argument == 8/9 (prefetch disable/enable).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Stop abusing ide_lock lock (switch to a private locking).
Fixes same issue as fixed by Alan Cox in atiixp host driver with
commit 6c5f8cc33e.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Stop abusing ide_lock lock (switch to a private locking).
Fixes same issue as fixed by Alan Cox in atiixp host driver with
commit 6c5f8cc33e.
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Keep local ide_pci_device_t copy in via_init_one().
* Adjust ide_pci_device_t copy according to id->driver_data in via_init_one()
and remove no longer needed second via82cxxx_chipsets[] entry.
* via82cxxx_chipsets[] -> via82cxxx_chipset.
* Remove IDE_HFLAGS_VIA define.
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_device_add() helper and convert host drivers to use it
instead of open-coded variants.
* Make ide_pci_setup_ports() and do_ide_setup_pci_device()
take 'u8 *idx' argument instead of 'ata_index_t *index'.
* Remove no longer needed ata_index_t.
* Unexport probe_hwif_init() and make it static.
* Unexport ide_proc_register_port().
There should be no functionality changes caused by this patch
(sgiioc4.c: ide_proc_register_port() requires hwif->present
to be set and it won't be set if probe_hwif_init() fails).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->fixup method to ide_hwif_t.
* Set hwif->fixup in ide_pci_setup_ports() to d->fixup.
* Use hwif->fixup in probe_hwif().
* Use probe_hwif_init() instead of probe_hwif_init_with_fixup() in
ide_setup_pci_device().
* Add 'fixup' argument to ide_register_hw() and use it to set hwif->fixup,
update all ide_register_hw() users accordingly.
* Convert ide-cs/delkin_cb host drivers to use ide_register_hw().
* Restore hwif->fixup in ide_hwif_restore().
* Remove ide_register_hw_with_fixup(), probe_hwif_init_with_fixup()
and 'fixup' argument from probe_hwif().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Split off sil_sata_udma_filter() from sil_udma_filter()
and rename sil_udma_filter() to sil_pata_udma_filter().
* Rename siimage_busproc() to sil_sata_busproc().
* Rename siimage_reset_poll() to sil_sata_reset_poll()
and in init_hwif_siimage() set ->reset_poll method only
for SATA controllers.
* Rename siimage_pre_reset() to sil_sata_pre_reset(),
in init_hwif_siimage() set ->pre_reset method only for
SATA controllers and remove redundant is_sata() call.
* Add CONFIG_BLK_DEV_IDE_SATA #ifdef/#endif to pdev_is_sata()
so compiler will know to throw out unused SATA code for
CONFIG_BLK_DEV_IDE_SATA=n case (830 bytes saved on x86-32).
* Bump driver version.
Some minor cleanups while at it:
* Convert sil_{pata,sata}_udma_filter() to use ATA_UDMA* defines.
* In siimage_mmio_ide_dma_test_irq() move 'base' variable
under 'if (SATA_ERROR_REG)' block.
* Simplify sil_sata_reset_poll() a bit.
* Cache is_sata() result in init_hwif_siimage()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make a local copy of ali15x3_chipset in alim15x3_init_one() and set
->host_flags / ->udma_mask according to the controller capabilities.
* Cleanup init_hwif_common_ali15x3().
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Setup CD_ROM DMA and PIO FIFO settings in init_chipset_ali15x3() instead
of ata66_ali15x3(). The latter is called from init_hwif_common_ali15x3()
only if DMA base exists (which insists m5529_revision > 0x20).
This changes makes CD_ROM DMA / PIO FIFO bits being set only once
and also when "idex=ata66" kernel parameter is used.
* While at it move also chip_is_1543c_e setup from ata66_ali15x3() to
init_chipset_ali15x3() and check if isa_dev exists before accessing it.
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_{IO_32BIT,UNMASK_IRQS} host flag to tell ide_pci_setup_ports()
to set drive->{io_32bit,unmask} for both drives on the interface. Convert
amd74xx, sl82c105 and via82cxxx host drivers to use these new host flags.
While at it:
* Add IDE_HFLAGS_AMD define (amd74xx host driver).
* Add IDE_HFLAGS_VIA define (via82cxxx host driver).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_RQSIZE_256 host flag to tell ide_pci_setup_ports() to set
hwif->rqsize to 256 sectors. Convert pdc202xx_old host driver to use it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_FORCE_LEGACY_IRQS host flag to tell ide_pci_setup_ports()
to always set hwif->irq to legacy IRQ 14/15 and convert generic IDE PCI
and via82cxxx host drivers to use it.
While at it:
* Add IDE_HFLAGS_UMC define (generic IDE PCI host driver).
* Remove no longer needed init_hwif_generic() (generic IDE PCI host driver).
* Set d->udma_mask instead of hwif->ultra_mask (via82cxxx host driver).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->chipset field to ide_pci_device_t and use it in ide_hwif_configure()
to set hwif->chipset. Convert cmd64x, cy82c693, rz1000 and trm290 host
drivers to use this new ability.
While at it define hwif_chipset_t as u8 to save some space in hw_regs_t,
ide_hwif_t and ide_pci_device_t instances.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Setting hwif->serialized makes sense only if the mate interface exists.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hwif->chipset should be set to ide_cmd646 also when DMA base is invalid.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch adds a missing "else" that was missing in
commit c77a89cd98.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Majority of host drivers using IDE PCI layer set drive->autotune, the only
exceptions are:
generic.c
ns87415.c
rz1000.c
trm290.c
* no ->set_pio_mode method
it821x.c:
* if memory allocation fails drive->autotune won't be set
(but there also won't be ->set_pio_mode method in such case)
piix.c:
* MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method)
However if there is no ->set_pio_mode method there are no changes in behavior
w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since cs5520 uses VDMA best PIO mode was tuned anyway by ide_dma_check()
but only if DMA was successfully initialized.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_LEGACY_IRQS host flag to tell ide_pci_setup_ports() to set
hwif->irq to legacy IRQ 14/15 (iff hwif->irq is not already set) and convert
atiixp, piix, serverworks, sis5513 and slc90e66 host drivers to use it.
While at it:
* In piix.c add IDE_HFLAGS_PIIX define and don't use ->init_hwif for MPIIX.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_SERIALIZE host flag to tell ide_pci_setup_ports() to set
hwif/mate->serialized and convert aec62xx, cs5530 and sc1200 host drivers
to use it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_ERROR_STOPS_FIFO host flag and use it instead
of hwif->err_stops_fifo. As a side-effect this change fixes
hwif->err_stops_fifo not being restored by ide_hwif_restore().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add DECLARE_ICH_DEV() macro.
While at it:
* Add init_hwif_ich() (->init_hwif method) for ICH controllers.
* Rename init_chipset_piix() to init_chipset_ich() and use it only for
ICH controllers.
* Remove no longer needed piix_is_ichx() helper.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* No need to disable UDMA in ->init_hwif method for ATP850UF (and since we
now always tune PIO it will be disabled by ->set_pio_mode calls anyway).
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge init_setup_{svwks,csb6}() into svwks_init_one().
While at it:
* Remove redundant dev->device checks.
* Operate on a local copy of serverworks_chipsets[] entry.
* Use pci_resource_start().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Split off pdc20270_get_dev2() helper from init_setup_pdc20270().
* Merge init_setup_{pdcnew,pdc20270,pdc20276}() into pdc202new_init_one().
While at it:
* Change KERN_ level of interrupt fixup message from KERN_WARNING to KERN_INFO.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Split off hpt{374,371,366}_init() helper from init_setup_hpt{374,371,366}().
* Merge init_setup_{374,372n,371,372a,302,366}() into hpt366_init_one().
While at it:
* Use "HPT36x" name for HPT366/HPT368 chipsets.
* Add .chip_name to struct hpt_info and use it to set set d->name.
* Convert .max_ultra in struct hpt_info to .udma_mask and use it to set
d->udma_mask.
* Fix hpt302 to use HPT302_ALLOW_ATA133_6 define.
* Change HPT366/HPT374 interrupt fixup message from KERN_WARNING to KERN_INFO.
* Use the second hpt366_chipsets[] entry for HPT37x chipsets using HPT36x PCI
device ID and fix .enablebits/.host_flags for HPT36x hpt366_chipsets[] entry.
* Bump driver version.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge init_setup_{aec62xx,aec6x80}() into aec62xx_init_one().
While at it:
* Use id->driver_data instead of dev->device.
* Use ATA_UDMA6 define.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID so
they were not converted by commit 44c10138fd.
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t.
* Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in
setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif
method may still override them).
* Convert IDE PCI host drivers to use ide_pci_device_t DMA masks.
While at it:
* Use ATA_{UDMA,MWDMA,SWDMA}* defines.
* hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345.
* serverworks.c: fix DMA masks being set before checking DMA base.
v2:
* Add missing masks to DECLARE_GENERIC_PCI_DEV() macro.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Documentation doesn't mention SWDMA and moreover all timings used
for SWDMA modes were over-clocked when compared to ATA spec.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_LBA48[_DMA] host flags, use it instead of hwif->no_lba48[_dma]
and then remove no longer needed hwif->no_lba48[_dma]. As a side-effect
this change fixes hwif->no_lba48_dma not being restored by ide_hwif_restore().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_pci_device_t.host_flags u32 and add IDE_HFLAG_CS5520 host flag.
* Pass ide_pci_device_t *d to setup-pci.c::ide_get_or_set_dma_base()
and use d->name instead of hwif->cds->name.
* Set IDE_HFLAG_CS5520 host flag in cs5520 host driver and use it in
ide_get_or_set_dma_base() to find out which PCI BAR to use, remove no longer
needed cs5520.c::cs5520_init_setup_dma() and ide_pci_device_t.init_setup_dma.
This fixes PCI bus-mastering not being checked for CS5510/CS5520 hosts.
v2:
* It is wrong to check simplex bits on CS5510/CS5520 as v1 did.
(Noticed by Alan).
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags. Convert all host drivers using
ide_pci_device_t to use these flags instead of d->autodma and then remove no
longer needed d->autodma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define. Convert
all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD}
instead of d->bootable and then remove no longer needed d->bootable.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA. Then remove no longer needed hwif->atapi_dma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add DECLARE_GENERIC_PCI_DEV() macro to generic IDE PCI host driver
and use it to cleanup generic_chipsets[].
* Remove dead/obsolete code while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The cs5535 uses an incorrect construct to access the other drive of a pair,
causing it to access beyond an array boundary on the secondary interface.
This fixes it by using the new ide_get_paired_drive() helper instead.
Bart: patch description fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@osdl.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The siimage uses an incorrect construct to access the other drive of a pair,
causing it to access beyond an array boundary on the secondary interface.
This fixes it by using the new ide_get_paired_drive() helper instead.
Bart: patch description fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@osdl.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This belongs to user-space (and only if really needed).
text data bss dec hex filename
6723 2000 28 8751 222f drivers/ide/pci/amd74xx.o.before
3833 2000 16 5849 16d9 drivers/ide/pci/amd74xx.o.after
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drive->dn is initialized by ide-probe.c::probe_hwif() so no need to do it
in ->init_hwif method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This belongs to user-space (and only if really needed).
text data bss dec hex filename
7129 404 8 7541 1d75 drivers/ide/pci/sis5513.o.before
3916 404 1 4321 10e1 drivers/ide/pci/sis5513.o.after
Additionaly to being bloat the code contained two bugs:
- wrong cable bit was checked (0x0001 instead of 0x8000) on ATA_133 chipsets
- incorrect UDMA cycle time was reported on ATA_100a/ATA_133 chipsets
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt34x.c: disable DMA masks for HPT345
(hwif->autodma is zero so DMA won't be enabled anyway).
* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
(hwif->autodma is zero so DMA won't be enabled anyway).
* Check noautodma global variable instead of drive->autodma in ide_tune_dma().
This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.
* Remove hwif->autodma (it was not checked by IDE core code anyway) and
drive->autodma (was set by all host drivers - except HPT345/TRM290 special
cases - unless "ide=nodma" was used).
While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
(this setting was always later over-ridden by host drivers anyway)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Clear prefetch and postwrite for ATAPI devices instead of depending on BIOS.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't force PIO4 when programming UDMA mode (suggested by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
on BIOS for programming device/controller for DMA. Set it in cy82c693,
generic, ns87415, opti621 and trm290 host drivers.
* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520
host driver.
* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.
* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
implementations. Fix all places checking for presence of ->ide_dma_check
hook to check for ->ide_dma_on instead.
* Remove no longer needed code from config_drive_for_dma().
* Make ide_tune_dma() static.
v2:
* Fix config_drive_for_dma() return values.
* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
dummy config_drive_for_dma() inline.
* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().
* Fix init_hwif_it8213() comment.
There should be no functionality changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since sl82c105 re-programs DMA/PIO timings for DMA enable/disable, and sets
->autotune this change shouldn't have any other effect than bringing sl82c105
driver in-line with other host drivers wrt ->ide_dma_check implementation.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add PIO autotune fallback to ->ide_dma_check.
Since cs5530/sc1200 allow separate PIO and DMA timings, and cs5530/sc1200
always set ->autotune this change shouldn't have any other effect than
bringing these drivers in-line with other host drivers wrt ->ide_dma_check
implementations.
* Fix ->ide_dma_check to return "-1" if DMA cannot be set.
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove ide_use_fast_pio() and just re-tune PIO unconditionally if DMA tuning
has failed in ->ide_dma_check. All host drivers using ide_use_fast_pio() set
drive->autotune so PIO is always tuned anyway and in some cases we _really_
need to re-tune PIO because PIO and DMA timings are shared.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Several host drivers used to reset drive->init_speed in their ->ide_dma_check
implementations which resulted in incorrect init speed being reported to the
user, fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix handling of unsupported/invalid modes in atiixp_set_dma_mode().
* ATI controllers allow separate PIO and DMA timings so remove programming
of PIO modes from atiixp_set_dma_mode(). Also remove no longer needed
atiixp_dma_2_pio() helper.
* SWDMA timings are not programmed by atiixp_set_dma_mode() and if SWDMA
mode is chosen atiixp_dma_host_on() erroneously enables UDMA, just disable
support for SWDMA modes for now.
* Enable support for MWDMA0 mode.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
