I have received some reports of out-of-memory errors on some older AMD
architectures. These errors are what I would expect to see if
crypt_stat->key were split between two separate pages. eCryptfs should
not assume that any of the memory sent through virt_to_scatterlist() is
all contained in a single page, and so this patch allocates two
scatterlist structs instead of one when processing keys. I have received
confirmation from one person affected by this bug that this patch resolves
the issue for him, and so I am submitting it for inclusion in a future
stable release.
Note that virt_to_scatterlist() runs sg_init_table() on the scatterlist
structs passed to it, so the calls to sg_init_table() in
decrypt_passphrase_encrypted_session_key() are redundant.
Signed-off-by: Michael Halcrow <mhalcrow@us.ibm.com>
Reported-by: Paulo J. S. Silva <pjssilva@ime.usp.br>
Cc: "Leon Woestenberg" <leon.woestenberg@gmail.com>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads.
Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LCD driver core calls LCD drivers when either the blanking state or
the display mode has changed, but does not make any check to see if the
called driver has a .set_mode method.
This means if a driver only has a .set_power method then the system will
OOPS on changing mode (and with the console semaphore held so you cannot
easily see the problem).
Fix the problem by ensuring that either callback is valid before use.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes a data corruption bug in pxa2xx_spi.c when operating in full duplex
mode with DMA and using buffers that overlap.
SPI transmit and receive buffers are allowed to be the same or to overlap.
However, this driver fails if such overlap is attempted in DMA mode
because it maps the rx and tx buffers in the wrong order. By mapping
DMA_FROM_DEVICE (read) before DMA_TO_DEVICE (write), it invalidates the
cache before flushing it, thus discarding data which should have been
transmitted.
The patch corrects the order of mapping. This bug exists in all versions
of pxa2xx_spi.c; similar bugs are in the drivers for two other SPI
controllers (au1500, imx).
A version of this patch has been tested on kernel 2.6.20 using
verification of loopback data with: random transfer length, random
bits-per-word, random positive offsets (both larger and smaller than
transfer length) between the start of the rx and tx buffers, and varying
clock rates.
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Cc: Vernon Sauder <vernoninhand@gmail.com>
Cc: J. Scott Merritt <merrij3@rpi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kunmap() takes as argument the struct page that orginally got kmap()'d,
however the sg_miter_stop() function passed it the kernel virtual address
instead, resulting in weird stuff.
Somehow I ended up fixing this bug by accident while looking for a bug in
the same area.
Reported-by: kerneloops.org
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Restore support for compiling tmiofb with acceleration disabled.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable -D DEBUG in the GRU Makefile if CONFIG_SGI_GRU_DEBUG is selected.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are already various drivers having bigger label than 12 bytes. Most
of them fit well under 20 bytes but make column width exact so that
oversized labels don't mess up output alignment.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: <stable@kernel.org> [2.6.26.x, 2.6.26.x, 2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add "min_addr" documentation.
For "max_addr", add nn before [KMG] since a number is needed and this
is consistent with other uses of [KMG].
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds the sparc syscall hookups.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a new accept4() system call. The addition of this system call
matches analogous changes in 2.6.27 (dup3(), evenfd2(), signalfd4(),
inotify_init1(), epoll_create1(), pipe2()) which added new system calls
that differed from analogous traditional system calls in adding a flags
argument that can be used to access additional functionality.
The accept4() system call is exactly the same as accept(), except that
it adds a flags bit-mask argument. Two flags are initially implemented.
(Most of the new system calls in 2.6.27 also had both of these flags.)
SOCK_CLOEXEC causes the close-on-exec (FD_CLOEXEC) flag to be enabled
for the new file descriptor returned by accept4(). This is a useful
security feature to avoid leaking information in a multithreaded
program where one thread is doing an accept() at the same time as
another thread is doing a fork() plus exec(). More details here:
http://udrepper.livejournal.com/20407.html "Secure File Descriptor Handling",
Ulrich Drepper).
The other flag is SOCK_NONBLOCK, which causes the O_NONBLOCK flag
to be enabled on the new open file description created by accept4().
(This flag is merely a convenience, saving the use of additional calls
fcntl(F_GETFL) and fcntl (F_SETFL) to achieve the same result.
Here's a test program. Works on x86-32. Should work on x86-64, but
I (mtk) don't have a system to hand to test with.
It tests accept4() with each of the four possible combinations of
SOCK_CLOEXEC and SOCK_NONBLOCK set/clear in 'flags', and verifies
that the appropriate flags are set on the file descriptor/open file
description returned by accept4().
I tested Ulrich's patch in this thread by applying against 2.6.28-rc2,
and it passes according to my test program.
/* test_accept4.c
Copyright (C) 2008, Linux Foundation, written by Michael Kerrisk
<mtk.manpages@gmail.com>
Licensed under the GNU GPLv2 or later.
*/
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/syscall.h>
#include <sys/socket.h>
#include <netinet/in.h>
#include <stdlib.h>
#include <fcntl.h>
#include <stdio.h>
#include <string.h>
#define PORT_NUM 33333
#define die(msg) do { perror(msg); exit(EXIT_FAILURE); } while (0)
/**********************************************************************/
/* The following is what we need until glibc gets a wrapper for
accept4() */
/* Flags for socket(), socketpair(), accept4() */
#ifndef SOCK_CLOEXEC
#define SOCK_CLOEXEC O_CLOEXEC
#endif
#ifndef SOCK_NONBLOCK
#define SOCK_NONBLOCK O_NONBLOCK
#endif
#ifdef __x86_64__
#define SYS_accept4 288
#elif __i386__
#define USE_SOCKETCALL 1
#define SYS_ACCEPT4 18
#else
#error "Sorry -- don't know the syscall # on this architecture"
#endif
static int
accept4(int fd, struct sockaddr *sockaddr, socklen_t *addrlen, int flags)
{
printf("Calling accept4(): flags = %x", flags);
if (flags != 0) {
printf(" (");
if (flags & SOCK_CLOEXEC)
printf("SOCK_CLOEXEC");
if ((flags & SOCK_CLOEXEC) && (flags & SOCK_NONBLOCK))
printf(" ");
if (flags & SOCK_NONBLOCK)
printf("SOCK_NONBLOCK");
printf(")");
}
printf("\n");
#if USE_SOCKETCALL
long args[6];
args[0] = fd;
args[1] = (long) sockaddr;
args[2] = (long) addrlen;
args[3] = flags;
return syscall(SYS_socketcall, SYS_ACCEPT4, args);
#else
return syscall(SYS_accept4, fd, sockaddr, addrlen, flags);
#endif
}
/**********************************************************************/
static int
do_test(int lfd, struct sockaddr_in *conn_addr,
int closeonexec_flag, int nonblock_flag)
{
int connfd, acceptfd;
int fdf, flf, fdf_pass, flf_pass;
struct sockaddr_in claddr;
socklen_t addrlen;
printf("=======================================\n");
connfd = socket(AF_INET, SOCK_STREAM, 0);
if (connfd == -1)
die("socket");
if (connect(connfd, (struct sockaddr *) conn_addr,
sizeof(struct sockaddr_in)) == -1)
die("connect");
addrlen = sizeof(struct sockaddr_in);
acceptfd = accept4(lfd, (struct sockaddr *) &claddr, &addrlen,
closeonexec_flag | nonblock_flag);
if (acceptfd == -1) {
perror("accept4()");
close(connfd);
return 0;
}
fdf = fcntl(acceptfd, F_GETFD);
if (fdf == -1)
die("fcntl:F_GETFD");
fdf_pass = ((fdf & FD_CLOEXEC) != 0) ==
((closeonexec_flag & SOCK_CLOEXEC) != 0);
printf("Close-on-exec flag is %sset (%s); ",
(fdf & FD_CLOEXEC) ? "" : "not ",
fdf_pass ? "OK" : "failed");
flf = fcntl(acceptfd, F_GETFL);
if (flf == -1)
die("fcntl:F_GETFD");
flf_pass = ((flf & O_NONBLOCK) != 0) ==
((nonblock_flag & SOCK_NONBLOCK) !=0);
printf("nonblock flag is %sset (%s)\n",
(flf & O_NONBLOCK) ? "" : "not ",
flf_pass ? "OK" : "failed");
close(acceptfd);
close(connfd);
printf("Test result: %s\n", (fdf_pass && flf_pass) ? "PASS" : "FAIL");
return fdf_pass && flf_pass;
}
static int
create_listening_socket(int port_num)
{
struct sockaddr_in svaddr;
int lfd;
int optval;
memset(&svaddr, 0, sizeof(struct sockaddr_in));
svaddr.sin_family = AF_INET;
svaddr.sin_addr.s_addr = htonl(INADDR_ANY);
svaddr.sin_port = htons(port_num);
lfd = socket(AF_INET, SOCK_STREAM, 0);
if (lfd == -1)
die("socket");
optval = 1;
if (setsockopt(lfd, SOL_SOCKET, SO_REUSEADDR, &optval,
sizeof(optval)) == -1)
die("setsockopt");
if (bind(lfd, (struct sockaddr *) &svaddr,
sizeof(struct sockaddr_in)) == -1)
die("bind");
if (listen(lfd, 5) == -1)
die("listen");
return lfd;
}
int
main(int argc, char *argv[])
{
struct sockaddr_in conn_addr;
int lfd;
int port_num;
int passed;
passed = 1;
port_num = (argc > 1) ? atoi(argv[1]) : PORT_NUM;
memset(&conn_addr, 0, sizeof(struct sockaddr_in));
conn_addr.sin_family = AF_INET;
conn_addr.sin_addr.s_addr = htonl(INADDR_LOOPBACK);
conn_addr.sin_port = htons(port_num);
lfd = create_listening_socket(port_num);
if (!do_test(lfd, &conn_addr, 0, 0))
passed = 0;
if (!do_test(lfd, &conn_addr, SOCK_CLOEXEC, 0))
passed = 0;
if (!do_test(lfd, &conn_addr, 0, SOCK_NONBLOCK))
passed = 0;
if (!do_test(lfd, &conn_addr, SOCK_CLOEXEC, SOCK_NONBLOCK))
passed = 0;
close(lfd);
exit(passed ? EXIT_SUCCESS : EXIT_FAILURE);
}
[mtk.manpages@gmail.com: rewrote changelog, updated test program]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Tested-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When booting in a direct color mode, the penguin has dirty feet, i.e.,
some pixels have the wrong color. This is caused by
fb_set_logo_directpalette() which does not initialize the last 32 palette
entries.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A problem was found while reviewing the code after Bugzilla bug
http://bugzilla.kernel.org/show_bug.cgi?id=11796.
In ipc_addid(), the newly allocated ipc structure is inserted into the
ipcs tree (i.e made visible to readers) without locking it. This is not
correct since its initialization continues after it has been inserted in
the tree.
This patch moves the ipc structure lock initialization + locking before
the actual insertion.
Signed-off-by: Nadia Derbey <Nadia.Derbey@bull.net>
Reported-by: Clement Calmels <cboulte@gmail.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The error test that follows the call to backlight_device_register semms
not to concern the right variable.
A simplified version of the semantic match that finds this problem is
as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@def0@
expression x;
position p0;
@@
x@p0 = backlight_device_register(...)
@protected@
expression def0.x,E;
position def0.p0;
position p;
statement S;
@@
x@p0
... when != x = E
if (!IS_ERR(x) && ...) {<... x@p ...>} else S
@unprotected@
expression def0.x;
identifier fld;
position def0.p0;
position p != protected.p;
@@
x@p0
... when != x = E
* x@p->fld
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for iMac 6.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Caleb Hyde <caleb.hyde@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rxfd->frag_info is a __le64, IPG_RFI_FRAGLEN is a cpu-endian
constant and wants to be outside of the le64_to_cpu. Fixed
in multiple places.
Also an occurrence where le64_to_cpu was used instead of cpu_to_le64
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous patch, 51e2a3846e, made
genphy_config_aneg() not restart aneg by calling genphy_restart_aneg() if
the advertisement hadn't changed.
But, genphy_restart_aneg() doesn't just restart aneg, it may also *enable*
aneg or un-isolate the PHY from the MII (those functions are controlled by
the same register). The code to avoid calling genphy_restart_aneg() didn't
consider this.
So, modify genphy_config_aneg() to also check if the PHY needs to have aneg
enabled or be un-isolated before deciding not to restart aneg.
This caused a problem with certain Davicom PHYs, as that driver isolates
the PHY (why?) before calling genphy_config_aneg() and expects the PHY to
be un-isolated by that function.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the minimal patch to fix endian mismatches. These are
probably bugs on big-endian arches, noops on little endian.
jme_rxsum_ok could be improved to directly take a __le16 and
change all of the masks/sets to be in little-endian, but
has not been done here to keep the patch small.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All MDIO bus drivers currently name bus with "%x" format.
There is one exception where mv643xx_eth driver is using "%d".
Phy address on the bus uses format "%02x".
Fixing phy name example to match all real life MDIO drivers.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several device drivers try to do things like netif_carrier_off()
before register_netdev() is invoked. This is bogus, but too many
drivers do this to fix them all up in one go.
Reported-by: Folkert van Heusden <folkert@vanheusden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] net/phonet/af_phonet.o
net/phonet/af_phonet.c: In function `pn_socket_create':
net/phonet/af_phonet.c:38: sorry, unimplemented: inlining failed in call to 'phonet_proto_put': function body not available
net/phonet/af_phonet.c:99: sorry, unimplemented: called from here
make[3]: *** [net/phonet/af_phonet.o] Error 1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] drivers/net/ixgbe/ixgbe_main.o
drivers/net/ixgbe/ixgbe_main.c: In function `ixgbe_intr':
drivers/net/ixgbe/ixgbe_main.c:1290: sorry, unimplemented: inlining failed in call to 'ixgbe_irq_enable': function body not available
drivers/net/ixgbe/ixgbe_main.c:1312: sorry, unimplemented: called from here
make[4]: *** [drivers/net/ixgbe/ixgbe_main.o] Error 1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before initialization, dev->irq may be zero. Make sure we don't disable
it at reset time in that case.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As number of TX queues in unrelated to number of CPU's we remove this test
and just make sure nxtq never gets exceeded.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to IPv6 ip6_mr_init() (fixed last week), the order of cleanup
operations in the error/exit section of ip_mr_init() is completely
inversed. It should be the other way around.
Also a del_timer() is missing in the error path.
I should have guessed last week that this same error existed in ipmr.c
too, as ip6mr.c is largely inspired by ipmr.c.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethernet0 (called FSL UEC0 in U-Boot) should be enet1 (UCC3/eth1), and
ethernet1 should be enet0 (UCC2/eth0), to be consistent with U-Boot so
that the interfaces do not swap addresses when control passes from
U-Boot to the kernel.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Marvell PHY driver is currently being used for the 88E1111 on the
SBC610. This driver is causing the link to run in 10/Half mode, the generic
PHY driver is correctly configuring the PHY as 1000/Full.
Edit default config to use generic PHY driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It's 1MB, not 512KB. Newer U-Boots will fix this entry, but that's no
reason to have the wrong value in the dts.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Impact: cleanup
I got the following warnings on IA64:
linux-2.6/drivers/pci/intel-iommu.c: In function 'init_dmars':
linux-2.6/drivers/pci/intel-iommu.c:1658: warning: format '%Lx' expects type 'long long unsigned int', but argument 2 has type 'u64'
linux-2.6/drivers/pci/intel-iommu.c:1663: warning: format '%Lx' expects type 'long long unsigned int', but argument 2 has type 'u64'
Another victim of int-ll64.h versus int-l64.h confusion between platforms.
->reg_base_addr has a type of u64 - which can only be printed out
consistently if we cast its type up to LL.
[ Eventually reg_base_addr should be converted to phys_addr_t, for which
we have the %pR printk helper - but that is out of the scope of late
-rc's. ]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clean up and fix for dyn ftrace filter selection
The previous logic of the dynamic ftrace selection of enabling
or disabling functions was complex and incorrect. This patch simplifies
the code and corrects the usage. This simplification also makes the
code more robust.
Here is the correct logic:
Given a function that can be traced by dynamic ftrace:
If the function is not to be traced, disable it if it was enabled.
(this is if the function is in the set_ftrace_notrace file)
(filter is on if there exists any functions in set_ftrace_filter file)
If the filter is on, and we are enabling functions:
If the function is in set_ftrace_filter, enable it if it is not
already enabled.
If the function is not in set_ftrace_filter, disable it if it is not
already disabled.
Otherwise, if the filter is off and we are enabling function tracing:
Enable the function if it is not already enabled.
Otherwise, if we are disabling function tracing:
Disable the function if it is not already disabled.
This code now sets or clears the ENABLED flag in the record, and at the
end it will enable the function if the flag is set, or disable the function
if the flag is cleared.
The parameters for the function that does the above logic is also
simplified. Instead of passing in confusing "new" and "old" where
they might be swapped if the "enabled" flag is not set. The old logic
even had one of the above always NULL and had to be filled in. The new
logic simply passes in one parameter called "nop". A "call" is calculated
in the code, and at the end of the logic, when we know we need to either
disable or enable the function, we can then use the "nop" and "call"
properly.
This code is more robust than the previous version.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix filter selection to apply when set
It can be confusing when the set_filter_functions is set (or cleared)
and the functions being recorded by the dynamic tracer does not
match.
This patch causes the code to be updated if the function tracer is
enabled and the filter is changed.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix of output of set_ftrace_filter
The commit "ftrace: do not show freed records in
available_filter_functions"
Removed a bit too much from the set_ftrace_filter code, where we now see
all functions in the set_ftrace_filter file even when we set a filter.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
So I dug deeper into the DMA problems I had with iwlagn and a kind soul
helped me in that he said something about pci-e alignment and mentioned
the iwl_rx_allocate function to check for crossing 4KB boundaries. Since
there's 8KB A-MPDU support, crossing 4k boundaries didn't seem like
something the device would fail with, but when I looked into the
function for a minute anyway I stumbled over this little gem:
BUG_ON(rxb->dma_addr & (~DMA_BIT_MASK(36) & 0xff));
Clearly, that is a totally bogus check, one would hope the compiler
removes it entirely. (Think about it)
After fixing it, I obviously ran into it, nothing guarantees the
alignment the way you want it, because of the way skbs and their
headroom are allocated. I won't explain that here nor double-check that
I'm right, that goes beyond what most of the CC'ed people care about.
So then I came up with the patch below, and so far my system has
survived minutes with 64K pages, when it would previously fail in
seconds. And I haven't seen a single instance of the TX bug either. But
when you see the patch it'll be pretty obvious to you why.
This should fix the following reported kernel bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=11596http://bugzilla.kernel.org/show_bug.cgi?id=11393http://bugzilla.kernel.org/show_bug.cgi?id=11983
I haven't checked if there are any elsewhere, but I suppose RHBZ will
have a few instances too...
I'd like to ask anyone who is CC'ed (those are people I know ran into
the bug) to try this patch.
I am convinced that this patch is correct in spirit, but I haven't
understood why, for example, there are so many unmap calls. I'm not
entirely convinced that this is the only bug leading to the TX reply
errors.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before ieee80211_notify_mac() was added, it was presented with the
use case of using it to tell mac80211 that the association may
have been lost because the firmware crashed/reset.
Since then, it has also been used by iwlwifi to (slightly) speed
up re-association after resume, a workaround around the fact that
mac80211 has no suspend/resume handling yet. It is also not used
by any other drivers, so clearly it cannot be necessary for "good
enough" suspend/resume.
Unfortunately, the callback suffers from a severe problem: It only
works for station mode. If suspend/resume happens while in IBSS or
any other mode (but station), then the callback is pointless.
Recently, it has created a number of locking issues, first because
it required rtnl locking rather than RCU due to calling sleeping
functions within the critical section, and now because it's called
by iwlwifi from the mac80211 workqueue that may not use the rtnl
because it is flushed under rtnl.
(cf. http://bugzilla.kernel.org/show_bug.cgi?id=12046)
I think, therefore, that we should take a step back, remove it
entirely for now and add the small feature it provided properly.
For suspend and resume we will need to introduce new hooks, and for
the case where the firmware was reset the driver will probably
simply just pretend it has done a suspend/resume cycle to get
mac80211 to reprogram the hardware completely, not just try to
connect to the current AP again in station mode. When doing so, we
will need to take into account locking issues and possibly defer
to schedule_work from within mac80211 for the resume operation,
while the suspend operation must be done directly.
Proper suspend/resume should also not necessarily try to reconnect
to the current AP, the time spent in suspend may have been short
enough to not be disconnected from the AP, mac80211 will detect
that the AP went out of range quickly if it did, and if the
association is lost then the AP will disassoc as soon as a data
frame is sent. We might also take into account WWOL then, and
have mac80211 program the hardware into such a mode where it is
available and requested.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
skb->tail can't be meant here because it's not the same across 32/64 bit
compilations. This means there's no way the current driver can work on
64-bit architectures.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.27]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__copy_from_user() will return invalid value 16 when it fails to
access user space and the size is 10.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Dell Optiplex 330 appears to hang on reboot. This is resolved by adding
a quirk to set bios reboot.
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: Steve Conklin <steve.conklin@canonical.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix tracing buffer mutex leak in case of allocation failure
This error was spotted by this semantic patch:
http://www.emn.fr/x-info/coccinelle/mut.html
It looks correct as far as I can tell. Please review.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This was recently changed to check for need_reconnect, but should
actually be a check for a tidStatus of CifsExiting.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: hold extra reference to bio in blk_rq_map_user_iov()
relay: fix cpu offline problem
Release old elevator on change elevator
block: fix boot failure with CONFIG_DEBUG_BLOCK_EXT_DEVT=y and nash
block/md: fix md autodetection
block: make add_partition() return pointer to hd_struct
block: fix add_partition() error path
By using WARN(), kerneloops.org can collect which component is causing
the delay and make statistics about that. suspend_test_finish() is
currently the number 2 item but unless we can collect who's causing
it we're not going to be able to fix the hot topic ones..
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
kernel/profile.c: fix section mismatch warning
function tracing: fix wrong pos computing when read buffer has been fulfilled
tracing: fix mmiotrace resizing crash
ring-buffer: no preempt for sched_clock()
ring-buffer: buffer record on/off switch
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
cpuset: fix regression when failed to generate sched domains
sched, signals: fix the racy usage of ->signal in account_group_xxx/run_posix_cpu_timers
sched: fix kernel warning on /proc/sched_debug access
sched: correct sched-rt-group.txt pathname in init/Kconfig
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
swiotlb: use coherent_dma_mask in alloc_coherent
MAINTAINERS: remove me as RAID maintainer
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: fix a broken define in dma-mapping
Blackfin arch: fix bug - Turn on DEBUG_DOUBLEFAULT, booting SMP kernel crash
Blackfin arch: fix bug - shared lib function in L2 failed be called
Blackfin arch: fix incorrect limit check for bf54x check_gpio
Blackfin arch: fix bug - Cpufreq assumes clocks in kHz and not Hz.
Blackfin arch: dont warn when running a kernel on the oldest supported silicon
Blackfin arch: fix bug - kernel build with write back policy fails to be booted up
Blackfin arch: fix bug - dmacopy test case fail on all platform
Blackfin arch: Fix typo when adding CONFIG_DEBUG_VERBOSE
Blackfin arch: don't copy bss when copying L1
Blackfin arch: fix bug - Fail to boot jffs2 kernel for BF561 with SMP patch
Blackfin arch: handle case of d_path() returning error in decode_address()