The NGW100 has a board controller which is hooked up to the TWI lines
on AP7000. Since the TWI driver isn't in mainline, use the i2c-gpio
driver in the mean time.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add GPIO led support: J2 to either block of LEDs on the STK1000.
This uses the new LEDS_GPIO driver, and sets up a heartbeat trigger by
default ... either bright (!!) amber, or a more interesting purple.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Adjust libata to ignore errors after spinup
This patch is to ignore errors from the spinup attempt if the drive is
in the "standby id" state.
Signed-off-by: Ryan Power <rpower@sysreset.com>
Acked-by: Mark Lord <liml@rtr.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add TECRA M7 to broken suspend list. Reported by Marie Koreen.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Marie Koreen <kbug@koreen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix several inconsistencies in these drivers WRT reporting the clocks:
- when using DPLL mode, 'pata_hpt37x' driver reported the DPLL frequency as the
PCI clock -- make it properly report both clocks and add the same ability to
the 'pata_hpt3x2n' driver;
- both drivers sometimes use "pata_hpt3*:" and sometimes "hpt3*:" in the
messages -- make them use only the former one;
- the message about failed DPLL stablizatios deserves KERN_ERR and a bang. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The DPLL tuning code always set up it for 66 MHz due to wrong UltraDMA mask
including mode 5 used to check for the necessity of 66 MHz clocking -- this
caused 66 MHz clock to be used for HPT374 chip that does not tolerate it.
While fixing this, also remove PLL mode from the TODO list -- I don't think
it's still a relevant item.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Maximum supported UDMA mode for AEC6280[R] is UDMA5 (not UDMA4)
and for AEC6880[R] it is UDMA6 (not UDMA5):
* Fix the problem by adding missing struct ata_port_info to artop_init_one().
* Use the right naming (s/626/628/).
* Bump driver version.
Fixes IDE->libata regression, problem was never present in IDE aec62xx driver.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Underneath all the HPT packaging, PCI identifiers, binary driver modules
and stuff you find that ...
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix probing of PS3 storage devices: in the success case, we should set
`error' to zero, not `result'.
Without this patch no storage devices are found.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ppc64 does the unusual thing of using #include on a compiler-generated
assembly file (lparmap.s) from an assembly source file (head_64.S).
This runs afoul of my recent patch to pass -gdwarf2 to the assembler
under CONFIG_DEBUG_INFO. This patch avoids the problem by disabling
DWARF generation (-g0) when producing lparmap.s.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 440 family of processors don't have a tlbie instruction. So, we
implement TLB invalidates by explicitly searching the TLB with tlbsx.,
then clobbering the relevant entry, if any. Unfortunately the PID for
the search needs to be stored in the MMUCR register, which is also
used by the TLB miss handler. Interrupts were enabled in _tlbie(), so
an interrupt between loading the MMUCR and the tlbsx could cause
incorrect search results, and thus a failure to invalide TLB entries
which needed to be invalidated.
This fixes the problem in both arch/ppc and arch/powerpc by inhibiting
interrupts (even critical and debug interrupts) across the relevant
instructions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
AFAICT, nobody is using ft_ordered(), and it causes a build warning
to be generated. This patch cleans that up by removing the function
and the commented-out code that calls it.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, spu_create with an invalid neighbo(u)r will return -ENOSYS,
not -EBADF, but only when spufs.o is built as a module.
This change adds the appropriate errno, making the behaviour the same
as the built-in case.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In sun4c_init_clean_mmu(), aligning 'kernel_end' using
SUN4C_REAL_PGDIR_ALIGN() is unnecessary since the caller
does this already.
In sun4c_paging_init(), 4 page sizes of "fluff" were added
to the address of &end. This was necessary a long time ago
when sparc32 would allocate some early data structures
by carving out memory chunks after &end but that no longer
occurs.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This mirrors sparc64 commit 715a0ecc29
sparc_ramdisk_image should always be decremented by KERNBASE.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When filling in the MBR signature array, the setup code failed to advance
boot_params.edd_mbr_sig_buf_entries, which resulted in the valid data
being ignored.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
At least one machine has been identified in the field which advertises
EDD for all drives but locks up if one attempts an extended read from
a non-primary drive.
The MBR is always at CHS 0-0-1, so there is no reason to use an
extended read, other than the possibility that the BIOS cannot handle
it.
Although this might break as many machines as it fixes (a small number
either way), the current state is a regression but the reverse is not.
Therefore revert to the previous state of not using extended read.
Quite probably the Right Thing to do is to read using plain (CHS) read
and extended read on failure, but that change would definitely have to
go through -mm first.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The Coverity checker spotted that we'd have already oops'ed if
"vlandev" was NULL.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the no longer used EXPORT_SYMBOL(dev_ethtool).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current display page is an 8-bit number, even though struct
screen_info gives it a 16-bit number. The number is returned in %bh,
so it needs to be >> 8 before storing.
Special thanks to Jeff Chua for detailed bug reporting.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Probe for hidden SSIDs if initiating pre-authentication scan and SSID
is set for STA interface.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I added the monitor for outgoing frames somehow a break
statement slipped in. Remove it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stp change code generates "sleeping function called from invalid
context" because rtnl_lock() called with BH disabled. This fixes it by
not acquiring then dropping the bridge lock.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't drop packets shorter than "SIP/2.0", just ignore them. Keep-alives
can validly be shorter for example.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The userinfo component of a SIP-URI is optional, continue parsing at the
beginning of the SIP-URI in case its not found.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check got lost during the conversion to nf_conntrack.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
An extraneous ";" makes xt_u32 match useless
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
[GFS2] Revert remounting w/o acl option leaves acls enabled
[GFS2] Fix setting of inherit jdata attr
[GFS2] Fix incorrect error path in prepare_write()
[GFS2] Fix incorrect return code in rgrp.c
[GFS2] soft lockup in rgblk_search
[GFS2] soft lockup detected in databuf_lo_before_commit
[DLM] fix basts for granted PR waiting CW
[DLM] More othercon fixes
[DLM] Fix memory leak in dlm_add_member() when dlm_node_weight() returns less than zero
[DLM] zero unused parts of sockaddr_storage
[DLM] fix NULL ls usage
[DLM] Clear othercon pointers when a connection is closed
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-s3c2410: Build fix
i2c/menelaus: Build fix
i2c-mv64xxx: Reinitialize hw and driver on I2C bus hang
i2c-mpc: Don't disable I2C module on stop condition
i2c-iop3xx: Set I2C_CLASS_HWMON to adapter class
i2c/isp1301_omap: Build fixes, whitespace
i2c-mpc: Pass correct dev_id to free_irq on error path
i2c-i801: Typo: erroneous
Fixup the include files after the arch moves that
where included in 2.6.23.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Under certain conditions, the mv64xxx I2C bus can hang preventing
further operation. To make the driver more robust, we now reset
the I2C hardware and the driver state machine when such hangs are
detected.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Disabling module on stop doesn't work on some CPUs (ie. mpc8241,
as reported by Guennadi Liakhovetski), so remove that.
Disable I2C module on errors/interrupts to prevent it from
locking up on mpc5200b.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In order to be able to use sensors on the IOP3xx SoCs, one needs to set
the adapter class to I2C_CLASS_HWMON.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Build fixes for isp1301_omap driver. I think an earlier version
of this must have gotten lost somewhere, or maybe it only went
into the Linux-OMAP tree.
Also, some whitespace fixes to bring this more into sync with the
version of this found in the Linux-OMAP tree. (That version has
updates for the OTG controller on the OMAP 1710 which break that
functionality on OMAP 161x boards like the H2, so merging all of
it is not currently an option.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPVS]: Use IP_VS_WAIT_WHILE when encessary.
[NET]: Share correct feature code between bridging and bonding
[ATM] drivers/atm/iphase.c: mostly kmalloc + memset conversion to kzalloc
[IRDA] irda-usb.c: mostly kmalloc + memset conversion to k[cz]alloc
[WAN] drivers/net/wan/hdlc_fr.c: kmalloc + memset conversion to kzalloc
[DCCP]: fix memory leak and clean up style - dccp_feat_empty_confirm()
[DCCP]: fix theoretical ccids_{read,write}_lock() race
[XFRM]: Clean up duplicate includes in net/xfrm/
[TIPC]: Clean up duplicate includes in net/tipc/
[SUNRPC]: Clean up duplicate includes in net/sunrpc/
[PKT_SCHED]: Clean up duplicate includes in net/sched/
[IPV6]: Clean up duplicate includes in net/ipv6/
[IPV4]: Clean up duplicate includes in net/ipv4/
[ATM]: Clean up duplicate includes in net/atm/
[ATM]: Clean up duplicate includes in drivers/atm/
[IPCONFIG]: ip_auto_config fix
[ATM]: fore200e_param_bs_queue() must be __devinit
The PCI driver has not been merged yet, so comment out call to
ks8695_init_pci() for now.
Also fix some incorrectly marked __init and __initdata sections.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Krzysztof Helt <krzysztof.h1@wp.pl>
This patch fixes a typo in architecture constant name.
The kernel for s3c2442 machines does not build without
this fix.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 569a7b6c2e. The
code was correct originally. The default setting for ACLs after a
remount should be to be the same as before the remount.
Signed-off-by: Abhijith Das <adas@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Due to a mix up between the jdata attribute and inherit jdata attribute
it has not been possible to set the inherit jdata attribute on
directories. This is now fixed and the ioctl will report the inherit
jdata attribute for directories rather than the jdata attribute as it
did previously. This stems from our need to have the one bit in the
ioctl attr flags mean two different things according to whether the
underlying inode is a directory or not.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
