It is possible for the timer expiry function to run even though the
request has already been handled: ide_timer_expiry() only checks that
the handler is not NULL, but it is possible that we have handled a
request (thus clearing the handler) and then started a new request
(thus starting the timer again, and setting a handler).
A simple way to exhibit this is to set the DMA timeout to 1 jiffy and
run dd: The kernel will panic after a few minutes because
ide_timer_expiry() tries to add a timer when it's already active.
To fix this, we simply add a request generation count that gets
incremented at every interrupt, and check in ide_timer_expiry() that
we have not already handled a new interrupt before running the expiry
function.
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
IDE error recovery is using IDLE IMMEDIATE if the drive is busy or has DRQ set.
This violates the ATA spec (can only send IDLEÂ IMMEDIATE when drive is not
busy) and really hoses up some drives (modern drives will not be able to
recover using this error handling). The correct thing to do is issue a SRST
followed by a SET FEATURES command. This is what Western Digital recommends
for error recovery and what Western Digital says Windows does.  It also does
not violate the ATA spec as far as I can tell.
Bart:
* port the patch over the current tree
* undo the recalibration code removal
* send SET FEATURES command after checking for good drive status
* don't check whether the current request is of REQ_TYPE_ATA_{CMD,TASK}
type because we need to send SET FEATURES before handling any requests
* some pre-ATA4 drives require INITIALIZE DEVICE PARAMETERS command before
other commands (except IDENTIFY) so send SET FEATURES only if there are
no pending drive->special requests
* update comments and patch description
* any bugs introduced by this patch are mine and not Suleiman's :-)
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The function ide_get_best_pio_mode() fails to return the correct IORDY setting
for the explicitly specified modes -- fix this along with the heading comment,
and also remove the long commented out code.
Also, while at it, correct the misliading comment about the PIO cycle time in
<linux/ide.h> -- it actually consists of only the active and recovery periods,
with only some chips also including the address setup time into equation...
[ bart: sl82c105 seems to be currently the only driver affected by this fix ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* since ide_hwif_t.ide_dma_host_on is called either when drive->using_dma == 1
or when return value is discarded make it void, also drop "ide_" prefix
* make __ide_dma_host_on() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_on() to atiixp_dma_host_on()
and sgiioc4_ide_dma_host_on() to sgiioc4_dma_host_on().
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* since ide_hwif_t.ide_dma_{host_off,off_quietly} always return '0'
make these functions void and while at it drop "ide_" prefix
* fix comment for __ide_dma_off_quietly()
* make __ide_dma_{host_off,off_quietly,off}() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_off() to atiixp_dma_host_off(),
sgiioc4_ide_dma_{host_off,off_quietly}() to sgiioc4_dma_{host_off,off_quietly}()
and sl82c105_ide_dma_off_quietly() to sl82c105_dma_off_quietly()
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
-1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
0 when DMA needs to be enabled (== need to call ->ide_dma_on)
1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All users of ->mmio == 1 are gone so convert ->mmio into flag.
Noticed by Alan Cox.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This results in smaller/faster/simpler code and allows future optimizations.
Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_use_fast_pio() helper for use by host drivers
* add DMA capability and hwif->autodma checks to ide_use_dma()
- au1xxx-ide/it8213/it821x drivers didn't check for (id->capability & 1)
[ for the IT8211/2 in SMART mode this check shouldn't be made but since
in it821x_fixups() we set DMA bit explicitly:
if(strstr(id->model, "Integrated Technology Express")) {
/* In raid mode the ident block is slightly buggy
We need to set the bits so that the IDE layer knows
LBA28. LBA48 and DMA ar valid */
id->capability |= 3; /* LBA28, DMA */
we are better off using generic helper if we can ]
- ide-cris driver didn't set ->autodma
[ before the patch hwif->autodma was only checked in the chipset specific
hwif->ide_dma_check implementations, for ide-cris it is cris_dma_check()
function so there no behavior change here ]
v2:
* updated patch description (thanks to Alan Cox for the feedback)
v3:
* updated for scc_pata driver
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This field is no longer used by the core IDE code so fix ide-{disk,floppy}
drivers to keep openers count in the driver specific objects and remove
it from ide-{cd,scsi,tape} drivers (it was write-only).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
patch 2/2:
Remove clearing bmdma status from cdrom_decode_status() since ATA devices
might need it as well.
(http://lkml.org/lkml/2006/12/4/201 and http://lkml.org/lkml/2006/11/15/94)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
patch 1/2 (revised):
- Fix drive->waiting_for_dma to work with CDB-intr devices.
- Do the dma status clearing in ide_intr() and add a new
hwif->ide_dma_clear_irq for Intel ICHx controllers.
Revised per Alan, Sergei and Bart's advice.
Patch against 2.6.20-rc6. Tested ok on my ICH4 and pdc20275 adapters.
Please review/apply, thanks.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This adds the module name to all PCI drivers, if they are built into the
kernel or not. It will show up in /sys/modules/MODULE_NAME/drivers/
It also fixes up the IDE core, which was calling __pci_register_driver()
directly.
Cc: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements ACPI integration for generic IDE devices.
The ACPI spec mandates that some methods are called during suspend and
resume. And consequently there most modern Laptops cannot resume
properly without it.
According to the spec, we should call '_GTM' (Get Timing) upon suspend
to store the current IDE adapter settings.
Upon resume we should call '_STM' (Set Timing) to initialize the
adapter with the stored settings; afterwards '_GTF' (Get Taskfile)
should be called which returns a buffer with some IDE initialisation
commands. Those commands should be passed to the drive.
There are two module params which control the behaviour of this patch:
'ide=noacpi'
Do not call any ACPI methods (Disables any ACPI method calls)
'ide=acpigtf'
Enable execution of _GTF methods upon resume.
Has no effect if 'ide=noacpi' is set.
'ide=acpionboot'
Enable execution of ACPI methods during boot.
This might be required on some machines if 'ide=acpigtf' is
selected as some machines modify the _GTF information
depending on the drive identification passed down with _STM.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While working on bidi support at struct request level
I have found that blk_queue_activity_fn is actually never used.
The only user is in ide-probe.c with this code:
/* enable led activity for disk drives only */
if (drive->media == ide_disk && hwif->led_act)
blk_queue_activity_fn(q, hwif->led_act, drive);
And led_act is never initialized anywhere.
(Looking back at older kernels it was used in the PPC arch, but was removed around 2.6.18)
Unless it is all for future use off course.
(this patch is against linux-2.6-block.git as off 2006/12/4)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The ESB2 appears to emit spurious DMA interrupts when configured for native
mode and handling ATAPI devices. Stratus were able to pin this bug down and
produce a patch. This is a rework which applies the fixup only to the ESB2
(for now). We can apply it to other chips later if the same problem is found.
This code has been tested and confirmed to fix the problem on the tested
systems.
Signed-off-by: Alan Cox <alan@redhat.com>
(Most of the hard work done by Stratus however)
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Michal Miroslaw reported a problem (bugzilla #7023) where a user initiated
reset while the IDE layer was already resetting the channel caused a crash,
and provided a rough fix.
This is a slightly cleaner version of the fix which tracks the reset state
and blocks further reset requests while a reset is in progress.
Note this is not a security issue - random end users can't access the
ioctl in question anyway.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove dma_base2 field from ide_hwif_t as it's used only in 2 drivers and
without great need.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: John Keller <jpk@sgi.com>
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make IDE_HWIFS configurable if EMBEDDED
This lets us lop as much as 16k off an x86 build. It's a little ugly, but
it's dead simple. Note the fix for HWIFS < 2.
Sizing interfaces dynamically unfortunately turns out to be pretty
major surgery.
add/remove: 0/1 grow/shrink: 0/11 up/down: 0/-16182 (-16182)
function old new delta
ide_hwifs 16920 1692 -15228
init_irq 1113 750 -363
ideprobe_init 283 138 -145
ide_pci_setup_ports 1329 1193 -136
save_match 85 - -85
ide_register_hw_with_fixup 367 287 -80
ide_setup 1364 1308 -56
is_chipset_set 40 4 -36
create_proc_ide_interfaces 225 205 -20
init_ide_data 84 67 -17
ide_probe_for_cmd640x 1198 1183 -15
ide_unregister 1452 1451 -1
Signed-off-by: Matt Mackall <mpm@selenic.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Claim extra DMA I/O ports regardless of what IDE channels are
present/enabled.
- Remove extra ports handling from ide_mapped_mmio_dma() since it's not
applicable to the custom-mapping IDE drivers.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some drives claim they support cache flushing, but get seriously
confused if you try. Add this option to be able to boot with
barriers enabled by default.
Signed-off-by: Jens Axboe <axboe@suse.de>
Make use of local_irq_enable_in_hardirq() API to annotate places that enable
hardirqs in hardirq context.
Has no effect on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
If the controller FIFO cleared automatically on error we must not try
and drain it as this will hang some chips.
Based in concept on a broken patch from -mm some while back
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a patch from Alan that fixes a real ide-cd.c regression causing
bogus "Media Check" failures for perfectly valid Fedora install ISOs, on
certain CD-ROM drives.
This is a forward port to 2.6.16 (from RHEL) of the minimal changes for the
end of media problem. It may not be sufficient for some controllers
(promise notably) and it does not touch the locking so the error path
locking is as horked as in mainstream.
From: Ingo Molnar <mingo@elte.hu>
I have ported the patch to 2.6.17-rc4 and tested it by provoking
end-of-media IO errors with an unaligned ISO image. Unlike the vanilla
kernel, the patched kernel interpreted the error condition correctly with
512 byte granularity:
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Illegal mode for this track or incompatible medium -- (asc=0x64, ascq=0x00)
The failed "Read 10" packet command was:
"28 00 00 04 fb 78 00 00 06 00 00 00 00 00 00 00 "
end_request: I/O error, dev hdc, sector 1306080
Buffer I/O error on device hdc, logical block 163260
Buffer I/O error on device hdc, logical block 163261
Buffer I/O error on device hdc, logical block 163262
the unpatched kernel produces an incorrect error dump:
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 1306080
Buffer I/O error on device hdc, logical block 163260
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 1306088
Buffer I/O error on device hdc, logical block 163261
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 1306096
Buffer I/O error on device hdc, logical block 163262
I do not have the right type of CD-ROM drive to reproduce the end-of-media
data corruption bug myself, but this same patch in RHEL solved it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Jens Axboe <axboe@suse.de>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noted by Sergei Shtylylov <sshtylyov@ru.mvista.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In some embedded systems the IDE hardware interface may only support 16-bit
or smaller accesses. Allow the interface to specify if this is the case
and don't allow the drive or user to override the setting.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since there's no longer any external user, we can make __ide_end_request()
static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch stops CompactFlash devices being marked as removable. They are
not removable (as defined by Linux) as the media and device are
inseparable. When a card is removed, the whole device is removed from the
system and never sits in a media-less state.
This stops some nasty udev device creation/destruction loops.
Further, once this change is made, there is no need for ide to can be
removed from ide_drive_t.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's a problem with the REQ_BLOCK_PC handling as well (bad ->data_len
handling) where it could actually complete a request ahead of time. I
suggest we just back this out for now, I will resubmit it later when I'm
fully confident in it.
This reverts commit 8672d57138
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch changes semaphores that are initialized as
locked to complete().
Source: MontaVista Software, Inc.
Modified-by: Steven Rostedt <rostedt@goodmis.org>
The following patch is from Montavista. I modified it slightly.
Semaphores are currently being used where it makes more sense for
completions. This patch corrects that.
Signed-off-by: Aleksey Makarov <amakarov@ru.mvista.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch makes IDE use the new blk_complete_request() interface.
There's still room for improvement, as __ide_end_request() really
could drop the lock after getting HWGROUP->rq (why does it need to
hold it in the first place? If ->rq access isn't serialized, we are
screwed anyways).
Signed-off-by: Jens Axboe <axboe@suse.de>
____cacheline_maxaligned_in_smp is currently used to align critical structures
and avoid false sharing. It uses per-arch L1_CACHE_SHIFT_MAX and people find
L1_CACHE_SHIFT_MAX useless.
However, we have been using ____cacheline_maxaligned_in_smp to align
structures on the internode cacheline size. As per Andi's suggestion,
following patch kills ____cacheline_maxaligned_in_smp and introduces
INTERNODE_CACHE_SHIFT, which defaults to L1_CACHE_SHIFT for all arches.
Arches needing L3/Internode cacheline alignment can define
INTERNODE_CACHE_SHIFT in the arch asm/cache.h. Patch replaces
____cacheline_maxaligned_in_smp with ____cacheline_internodealigned_in_smp
With this patch, L1_CACHE_SHIFT_MAX can be killed
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove duplicate documentation for ide_do_drive_cmd() from
<linux/ide.h>, this function is already documented in ide-io.c.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The structure ide_driver_t have a .owner field which is a duplicate
of .gendriver.owner field (.gen_driver is a struct device_driver).
This patch removes ide_driver_t's owner field.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
A nice feature of sysfs is that it can create the symlink from the
driver to the module that is contained in it.
It requires that the device_driver.owner is set, what is not the
case for many PCI drivers.
This patch allows pci_register_driver to set automatically the
device_driver.owner for any PCI driver.
Credits to Al Viro who suggested the method.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
--
drivers/ide/setup-pci.c | 12 +++++++-----
drivers/pci/pci-driver.c | 9 +++++----
include/linux/ide.h | 3 ++-
include/linux/pci.h | 10 ++++++++--
4 files changed, 22 insertions(+), 12 deletions(-)
CONFIG_IDE_MAX_HWIFS is a generic thing, no need to have it duplicated
by every arch that uses it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Devices driven by ide-cs will appear under /sys/devices instead of the
appropriate PCMCIA device. To fix this I had to extend the hw_regs_t
structure with a 'struct device' field, which allows us to set the
parent link for the appropriate hwif.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@suse.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
