This driver was declared obsolete over 2 years ago, the alternative
console driver for legacy iSeries (hvc_iseries) was made the default
over 1 year ago and this driver has been build broken for over 3
months, so remove it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the i2c code which is now obsolete due to the new
ibm iic driver walking the device tree for child nodes.
There are two other small cleanups that came indirectly from the ad7414
code review. Make sure Tlow is correct and handle the case where
i2c_smbus_read_word_data fails.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Now that arch/ppc is gone and CONFIG_PPC_MERGE is always set, remove
the dead code associated with !CONFIG_PPC_MERGE from arch/powerpc
and include/asm-powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Lockless get_user_pages_fast() for 64-bit (v3)
powerpc: Don't use the wrong thread_struct for ptrace get/set VSX regs
powerpc: Fix ptrace buffer size for VSX
powerpc: Correctly hookup PTRACE_GET/SETVSRREGS for 32 bit processes
ide/powermac: Fix use of uninitialized pointer on media-bay
powerpc: Allow non-hcall return values for lparcfg writes
ipmi/powerpc: Use linux/of_{device,platform}.h instead of asm
powerpc/fsl: proliferate simple-bus compatibility to soc nodes
Documentation: remove old sbc8260 board specific information
cpm2: Rework baud rate generators configuration to support external clocks.
powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC
cpm_uart: Add generic clock API support to set baudrates
cpm_uart: Modem control lines support
powerpc: implement GPIO LIB API on CPM1 Freescale SoC.
cpm2: Implement GPIO LIB API on CPM2 Freescale SoC.
powerpc: Fix 8xx build failure
powerpc: clean up the Book-E HW watchpoint support
Ingo Molnar provided a fix to not call _PPC at processor driver
initialization time in "[PATCH] ACPI: fix cpufreq regression" (git
commit e4233dec74)
But it can still happen that _PPC is called at processor driver
initialization time.
This patch should make sure that this is not possible anymore.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
add simple-bus compatible property to soc nodes for 83xx/85xx platforms
that were missing them. Add same to platform probe code.
This fixes SoC device drivers (such as talitos) to succeed in matching
devices present in the soc node.
also update mpc836x_rdk dts to new SEC bindings (overlooked in commit
3fd4473: powerpc/fsl: update crypto node definition and device tree
instances).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch introduces baudrate setting support via the generic clock API.
When present the optional device tree clock property is used instead of
fsl-cpm-brg. Platforms can then define complex clock schemes, to output
the serial clock on an external pin for instance.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch implement GPIO LIB support for the CPM1 GPIOs.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch implement GPIO LIB support for the CPM2 GPIOs. The code can
also be used for CPM1 GPIO port E, as both cores are compatible at the
register level.
Based on earlier work by Laurent Pinchart.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This removes the non-working code in legacy_serial that tried to handle
the powermac SCC ports, and instead add a (now working) function to the
powermac platform code to find the default serial console if any.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When using the "sccdbg" option to route early kernel messages and
xmon to the SCC serial port on PowerMacs, when this wasn't the
configured output port of Open Firmware, we initialize the baudrate
to 57600bps. This isn't a very good default on some powermacs where
both the FW and pmac_zilog will default to 38400. This fixes it to
use the same logic as pmac_zilog to pick a default speed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Noticed due to these wanings:
arch/powerpc/platforms/pseries/cmm.c:298: warning: initialization from incompatible pointer type
arch/powerpc/platforms/pseries/cmm.c:299: warning: initialization from incompatible pointer type
arch/powerpc/platforms/pseries/cmm.c:320: warning: initialization from incompatible pointer type
arch/powerpc/platforms/pseries/cmm.c:320: warning: initialization from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kmem cache passed to constructor is only needed for constructors that are
themselves multiplexeres. Nobody uses this "feature", nor does anybody uses
passed kmem cache in non-trivial way, so pass only pointer to object.
Non-trivial places are:
arch/powerpc/mm/init_64.c
arch/powerpc/mm/hugetlbpage.c
This is flag day, yes.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Jon Tollefson <kniht@linux.vnet.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Matt Mackall <mpm@selenic.com>
[akpm@linux-foundation.org: fix arch/powerpc/mm/hugetlbpage.c]
[akpm@linux-foundation.org: fix mm/slab.c]
[akpm@linux-foundation.org: fix ubifs]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (34 commits)
powerpc: Wireup new syscalls
Move update_mmu_cache() declaration from tlbflush.h to pgtable.h
powerpc/pseries: Remove kmalloc call in handling writes to lparcfg
powerpc/pseries: Update arch vector to indicate support for CMO
ibmvfc: Add support for collaborative memory overcommit
ibmvscsi: driver enablement for CMO
ibmveth: enable driver for CMO
ibmveth: Automatically enable larger rx buffer pools for larger mtu
powerpc/pseries: Verify CMO memory entitlement updates with virtual I/O
powerpc/pseries: vio bus support for CMO
powerpc/pseries: iommu enablement for CMO
powerpc/pseries: Add CMO paging statistics
powerpc/pseries: Add collaborative memory manager
powerpc/pseries: Utilities to set firmware page state
powerpc/pseries: Enable CMO feature during platform setup
powerpc/pseries: Split retrieval of processor entitlement data into a helper routine
powerpc/pseries: Add memory entitlement capabilities to /proc/ppc64/lparcfg
powerpc/pseries: Split processor entitlement retrieval and gathering to helper routines
powerpc/pseries: Remove extraneous error reporting for hcall failures in lparcfg
powerpc: Fix compile error with binutils 2.15
...
Fixed up conflict in arch/powerpc/platforms/52xx/Kconfig manually.
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To support Cooperative Memory Overcommitment (CMO), we need to check
for failure from some of the tce hcalls.
These changes for the pseries platform affect the powerpc architecture;
patches for the other affected platforms are included in this patch.
pSeries platform IOMMU code changes:
* platform TCE functions must handle H_NOT_ENOUGH_RESOURCES errors and
return an error.
Architecture IOMMU code changes:
* Calls to ppc_md.tce_build need to check return values and return
DMA_MAPPING_ERROR for transient errors.
Architecture changes:
* struct machdep_calls for tce_build*_pSeriesLP functions need to change
to indicate failure.
* all other platforms will need updates to iommu functions to match the new
calling semantics; they will return 0 on success. The other platforms
default configs have been built, but no further testing was performed.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adds a collaborative memory manager, which acts as a simple balloon driver
for System p machines that support cooperative memory overcommitment
(CMO).
Adds a platform configuration option for CMO called PPC_SMLPAR.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Newer versions of firmware support page states, which are used by the
collaborative memory manager (future patch) to "loan" pages to the
hypervisor for use by other partitions.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For Cooperative Memory Overcommitment (CMO), set the FW_FEATURE_CMO
flag in powerpc_firmware_features from the rtas ibm,get-system-parameters
table prior to calling iommu_init_early_pSeries.
With this, any CMO specific functionality can be controlled by checking:
firmware_has_feature(FW_FEATURE_CMO)
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the moment the fixed mapping is by default strongly ordered (the
iommu_fixed=weak boot option must be used to make the fixed mapping weakly
ordered). If we're on a setup where the southbridge is being used in
endpoint mode (triblade and CAB boards) the default should be a weakly
ordered fixed mapping.
This adds a check so that if a node of type pcie-endpoint can be found in
the device tree the fixed mapping is set to be weak by default (but can be
overridden using iommu_fixed=strong).
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well
nohz: prevent tick stop outside of the idle loop
This uses the new vm_ops->access to allow gdb to access the SPU local
store. We currently prevent access to problem state registers, this can
be done later if really needed but it's safer not to.
[akpm@linux-foundation.org: fix typo]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adjusts the placement of a reference context from
a spu affinity chain. The reference context can now be placed
only on nodes that have enough spus not intended to be used by
another gang (already running on the node).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currenlt,, it is possible to lock aff_mutex and
cbe_spu_info[n].list_mutex in different orders, allowing a deadlock to
occur. With this change, aff_mutex is not taken within a list_mutex
critical section anymore.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
This patch removes the old kgdb reminants from ARCH=powerpc and
implements the new style arch specific stub for the common kgdb core
interface.
It is possible to have xmon and kgdb in the same kernel, but you
cannot use both at the same time because there is only one set of
debug hooks.
The arch specific kgdb implementation saves the previous state of the
debug hooks and restores them if you unconfigure the kgdb I/O driver.
Kgdb should have no impact on a kernel that has no kgdb I/O driver
configured.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
kcalloc is supposed to be called with the count as its first argument and
the element size as the second.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (49 commits)
powerpc: Fix build bug with binutils < 2.18 and GCC < 4.2
powerpc/eeh: Don't panic when EEH_MAX_FAILS is exceeded
fbdev: Teaches offb about palette on radeon r5xx/r6xx
powerpc/cell/edac: Log a syndrome code in case of correctable error
powerpc/cell: Add DMA_ATTR_WEAK_ORDERING dma attribute and use in Cell IOMMU code
powerpc: Indicate which oprofile counters to use while in compat mode
powerpc/boot: Change spaces to tabs
powerpc: Remove duplicate 6xx option in Kconfig
powerpc: Use PPC_LONG and PPC_LONG_ALIGN in lib/string.S
powerpc: Use PPC_LONG_ALIGN in uaccess.h
powerpc: Add a #define for aligning to a long-sized boundary
powerpc: Fix OF parsing of 64 bits PCI addresses
powerpc: Use WARN_ON(1) instead of __WARN()
powerpc: Fix support for latencytop
powerpc/ps3: Update ps3_defconfig
powerpc/ps3: Add a sub-match id to ps3_system_bus
powerpc: Add a 6xx defconfig
powerpc/dma: Use the struct dma_attrs in iommu code
powerpc/cell: Add support for power button of future IBM cell blades
powerpc/cell: Cleanup sysreset_hack for IBM cell blades
...
This allow to dynamically generate attributes and share show/store
functions between attributes. Right now most attributes are generated
by special macros and lots of duplicated code. With the attribute
passed it's instead possible to attach some data to the attribute
and then use that in shared low level functions to do different things.
I need this for the dynamically generated bank attributes in the x86
machine check code, but it'll allow some further cleanups.
I converted all users in tree to the new show/store prototype. It's a single
huge patch to avoid unbisectable sections.
Runtime tested: x86-32, x86-64
Compiled only: ia64, powerpc
Not compile tested/only grep converted: sh, arm, avr32
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have the dev_printk() variants for this kind of thing, use them
instead of directly trying to access the bus_id field of struct device.
This is done in order to remove bus_id entirely.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the EEH_MAX_FAILS action from panic to printing an
error message. Panicking under under this condition is too harsh.
Although performance will be affected and the device may not recover,
the system is still running, which at the very least should allow for a
more graceful shutdown. The patch also removes the msleep() within a
spinlock, which can lead to a deadlock and is not recommended.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Introduce a new dma attriblue DMA_ATTR_WEAK_ORDERING to use weak ordering
on DMA mappings in the Cell processor. Add the code to the Cell's IOMMU
implementation to use this code.
Dynamic mappings can be weakly or strongly ordered on an individual basis
but the fixed mapping has to be either completely strong or completely weak.
This is currently decided by a kernel boot option (pass iommu_fixed=weak
for a weakly ordered fixed linear mapping, strongly ordered is the default).
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The real option is above in the same Kconfig file.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add sub match id for ps3 system bus so that two different system bus
devices can be connected to a shared device.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update iommu_alloc() to take the struct dma_attrs and pass them on to
tce_build(). This change propagates down to the tce_build functions of
all the platforms.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for the power button on future IBM cell blades.
It actually doesn't shut down the machine. Instead it exposes an
input device /dev/input/event0 to userspace which sends KEY_POWER
if power button has been pressed.
haldaemon actually recognizes the button, so a plattform independent acpid
replacement should handle it correctly.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a config option for the sysreset_hack used for
IBM Cell blades. The code is moves from pervasive.c into ras.c and
gets it's own init method.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a cpufreq governor that takes the number of running spus
into account. It's very similar to the ondemand governor, but not as complex.
Instead of hacking spu load into the ondemand governor it might be easier to
have cpufreq accepting multiple governors per cpu in future.
Don't know if this is the right way, but it would keep the governors simple.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jack Ren and Eric Miao tracked down the following long standing
problem in the NOHZ code:
scheduler switch to idle task
enable interrupts
Window starts here
----> interrupt happens (does not set NEED_RESCHED)
irq_exit() stops the tick
----> interrupt happens (does set NEED_RESCHED)
return from schedule()
cpu_idle(): preempt_disable();
Window ends here
The interrupts can happen at any point inside the race window. The
first interrupt stops the tick, the second one causes the scheduler to
rerun and switch away from idle again and we end up with the tick
disabled.
The fact that it needs two interrupts where the first one does not set
NEED_RESCHED and the second one does made the bug obscure and extremly
hard to reproduce and analyse. Kudos to Jack and Eric.
Solution: Limit the NOHZ functionality to the idle loop to make sure
that we can not run into such a situation ever again.
cpu_idle()
{
preempt_disable();
while(1) {
tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we
are in the idle loop
while (!need_resched())
halt();
tick_nohz_restart_sched_tick(); <- disables NOHZ mode
preempt_enable_no_resched();
schedule();
preempt_disable();
}
}
In hindsight we should have done this forever, but ...
/me grabs a large brown paperbag.
Debugged-by: Jack Ren <jack.ren@marvell.com>,
Debugged-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This reverts commit e3621ee633.
This was not the proper fix. As Scott Wood said CONFIG_FS_ENET has nothing
to do with the issue. The proper fix is to select PHYLIB for this board.
Its possible to build the phylib as a module, however this breaks the
board code because alloc_mdio_bitbang and mdiobus_register are not
available if we build as a module. These are needed by the board code
since it implements the low level mdio bitbang ops.
So we unconditionally select PHYLIB to ensure its built into the kernel
if we are building in EP8248E support.
Long term we should look at moving the mdio_ops into its own file so it
can be built as a module.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With arch/ppc gone and all in kernel users of CONFIG_PPC_CPM_NEW_BINDING
fixed up we dont have need for the Kconfig option anymore.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Get rid of uses_fsl_uli_m1575, it does not scale for all cases.
Instead, let's explicitly use machine_is() for each fixup.
- Factor out MPC8610HPCD quirks to fsl_uli1575, and protect them with
machine_is(). One step closer to multiplatform kernels.
- Actually use fsl_uli1575 on MPC8610HPCD, so RTC quirk will be applied.
- RTC quirk applies to all boards though, so no machine_is() checks.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes RTC on MPC8572DS boards: dummy read helps only when
reading at the end of the bridge's memory (i.e. outside of behind the
bridge devices' assigned regions).
With this change the quirk also makes RTC work on MPC8610HPCD, so it's
unlikely that this will break MPC8641HPCN or MPC8544DS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We must not use MPC831X_SICR[HL]_* definitions for the MPC8315 processors,
because SICR USB bits locations are not compatible with MPC8313.
This patch fixes ULPI workability on MPC8315E-RDB boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This allows other platforms with the same pci block like MPC5121 to use it.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Choosing PCI or not at config time is allowed on some
platforms via an if expression in arch/powerpc/Kconfig.
To add a new platform with PCI support selectable at
config time, you must change the if expression. This
patch makes this easier by changing:
bool "PCI support" if <long expression>
to
bool "PCI support" if PPC_PCI_CHOICE
and adding select PPC_PCI_CHOICE to all the config nodes that
were previously in the PCI if expression.
Platforms with unconditional PCI support continue to
just select PCI in their config nodes.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Basic PM support for 83xx. Standby is implemented as sleep.
Suspend-to-RAM is implemented as "deep sleep" (with the processor
turned off) on 831x.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If we don't enable FS_ENET we get build issues:
arch/powerpc/platforms/built-in.o: In function `ep8248e_mdio_probe':
arch/powerpc/platforms/82xx/ep8248e.c:129: undefined reference to `alloc_mdio_bitbang'
arch/powerpc/platforms/82xx/ep8248e.c:143: undefined reference to `mdiobus_register'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is okay for both _PAGE_GUARDED and _PAGE_COHERENT (G and M) to be set
in the same pte. In fact, even if that were not the case, there doesn't
seem to be any place where G is set without also setting I (_PAGE_NO_CACHE),
so the test for I is sufficient as a condition to clear _PAGE_COHERENT
when filling the hash table.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the "uninitialized use" compile warning and avoid potential
runtime issue.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There isn't any reason at this point that we can't build 82xx, 83xx & 86xx
support in with the other 6xx based boards. Twiddle the Kconfigs to allow
this.
This allows us to remove the machine type selection for related to 6xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Publish the devices listed in dts under SOC as of_device for 85xx_cds
platform. The devices are needed by the 85xx EDAC driver.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Moved the pic initialization into its own common file and out of the board
code. Also fixed the OF reference counting on the mpic node.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initialize I2C pins on boards with CPM1/CPM2 controllers and document the
i2c bus in booting-without-of.
The boards don't have any I2C chips connected to the I2C bus, so unless
some external chips are connected to the boards, this code is just an
example of setting everything else up.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These issues were reported by Stephen Rothwell for another 85xx board
port and pointed out by Chen Gong as issues in the DS port.
* mpic OF node reference counting was off
* of_device_id struct should be marked as __initdata
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix interrupt threading issue on pq2fads when running with CONFIG_PREEMPT_RT
Signed-off-by: Rune Torgersen <runet@innovsys.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a interrupt host for the interrupt controller in the mpc5121ads cpld.
PCI interrupts are 0-7 the rest are 8-15 Touchscreen pendown irq is
hardwired to irq1 All other irqs are chained to irq0
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move shared code from mpc5121_ads.c to new file mpc512x_shared.c
- mpc512x_find_ips_freq -> unchanged
- contents of mpc5121_ads_init_IRQ -> mpc512x_init_IRQ
- looking for fsl,mpc5121-ipic instead of fsl,ipic
- mpc5121_ads_declare_of_platform_devices -> mpc5121_declare_of_platform_devices
- and use compatible for lookup instead of node name
Add new generic board setup mpc5121_generic.c
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Plugs into the generic powerpc clock driver in
arch/powerpc/kernel/clock.c
The following subset of clk_interface is implemented:
clk_get, clk_put: get clock via name, release clock
clk_enable, clk_disable: enable or disable clock
clk_get_rate: get clock rate in Hz
clk_set_rate: stubbed
clk_round_rate: stubbed
clk_set_parent: NULL
clk_get_parent: NULL
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
On MPC5200 the PCI target control register (PCITCR) @ MBAR + 0xD6C is
initialized with only bit 7 (Latrule disable) set. The 8-Bit write
combine timer (Bits 24..31) should be also set to a reasonable value
_greater zero_ (0x08 = default) since setting it to 0x00 leads to
_very poor_ performance as a PCI target since external burst won't be
possible at all.
Setting the WCT to 0x08 (cache-line size) leads to good overall perfomance.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow the Rev A Warp boards to boot from NAND.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The following patch restores the PERR and SERR bits in the PCI
command register during an EEH device recovery. We have found
at least one case (an Agilent test card) where the PERR/SERR
bits are set to 1 by firmware at boot time, but are not restored
to 1 during EEH recovery. The patch fixes the Agilent card
problem. It has been tested on several other EEH-enabled cards
with no regressions.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current low level hash code on LPAR configurations clears
_PAGE_COHERENT (M) when either _PAGE_GUARDED (G) or _PAGE_NO_CACHE (I)
is set. This conflicts with _PAGE_SAO which has M, I and W bits sets at
once (normally invalid combo) to indicate the new SAO attribute.
This changes the code to allow that case.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make cell_dma_dev_setup_iommu() return a pointer to the struct iommu_table
(or NULL if no table can be found) rather than putting this pointer into
dev->archdata.dma_data (let the caller do that), and rename this function
to cell_get_iommu_table() to reflect this change.
This will allow us to get the iommu table for a device that doesn't have
the table in the archdata.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update powerpc to use the new dma_*map*_attrs() interfaces. In doing so
update struct dma_mapping_ops to accept a struct dma_attrs and propagate
these changes through to all users of the code (generic IOMMU and the
64bit DMA code, and the iseries and ps3 platform code).
The old dma_*map_*() interfaces are reimplemented as calls to the
corresponding new interfaces.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As nr_active counter includes also spus waiting for syscalls to return
we need a seperate counter that only counts spus that are currently running
on spu side. This counter shall be used by a cpufreq governor that targets
a frequency dependent from the number of running spus.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reduce the output verbosity of ps3_system_bus_match().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the .ctx debug file in spu context directories is always
present.
We'd prefer to prevent users from relying on this file, so add a
"debug" mount option to spufs. The .ctx file will only be added to
the context directories when this option is present.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Populate the size member of a few context files. Leave out files that
have different semantics with read vs mmap, or contain a
variable-length hex string.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, spufs never specifies the i_size for the files in context
directories, so stat() always reports 0-byte files.
This change adds allows the spufs_dir_(nosched_)contents arrays to
specify a file size. This allows stat() to report correct file sizes,
and makes SEEK_END work.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
An spu context shouldn't get an extra tick if the time slice code
couldn't find something else to run. This means contexts that are not
within spu_run (ie, SPU_SCHED_SPU_RUN is cleared) will not receive
extra ticks while we have no other contexts waiting.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Add a ctxt file to spufs that shows spu context information that is used
in scheduling. This info can be used for debugging spufs scheduler
issues, and to isolate between application and spufs problems as it
shows a lot of state such as priorities and dispatch counts.
This file contains internal spufs state and is subject to change at any
time, and therefore no applications should depend on it. The file is
intended for the use of spufs kernel developers.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Support for the Xilinx Virtex5 FXT 440 is being added.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This updates the device tree manipulation routines so that memory
add/remove of lmbs represented under the
ibm,dynamic-reconfiguration-memory node of the device tree invokes the
hotplug notifier chain.
This change is needed because of the change in the way memory is
represented under the ibm,dynamic-reconfiguration-memory node. All lmbs
are described in the ibm,dynamic-memory property instead of having a
separate node for each lmb as in previous device tree layouts. This
requires the update_node() routine to check for updates to the
ibm,dynamic-memory property and invoke the hotplug notifier chain.
This also updates the pseries hotplug notifier to be able to gather information
for lmbs represented under the ibm,dynamic-reconfiguration-memory node and
have the lmbs added/removed.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use the base address of the lmb to derive the starting page frame number
instead of trying to extract it from the drc index of the lmb. The drc
index should not be used for this as it will, and did, break.
Until this point, systems that have had memory represented in the device
tree with a node for each lmb the drc index would (luckily) closely
track the base address of the lmb. For example a lmb with a drc index
of 8000000a would have a base address of a0000000. This correlation
allowed the current code to derive the starting page frame number from
the drc inddex
Device tree layouts where lmbs are represented under the
ibm,dynamic-reconfiguration-memory node in the ibm,dynamic-memory
property do not have this correlation between the drc index and base
address of the lmb.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allow the phandle passed to the /proc/ppc64/ofdt file to be specified
in formats other than decimal. This allows us to easily specify phandle
values in hex that would otherwise appear as negative integers.
This is an issue on systems where the value of
/proc/device-tree/ibm,dynamic-reconfiguration-memory.ibm,phandle is
fffffff9. Having to pass this to the ofdt file as a string results in
a large negative number, and simple_strtoul() does not handle negative
numbers.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Suspend/resume ("echo mem > /sys/power/state") does not work with
vanilla kernels -- the system does not suspend correctly and just
hangs. This patch fixes this so suspend/resume works:
1) of_iomap does not map the whole 0xC000 of the MPC5200 immr so
saving registers does not work.
2) PCI registers need to be saved and restored.
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add CONFIG_VSX config build option. Must compile with POWER4, FPU and ALTIVEC.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently create_branch() creates a branch instruction for you, and
patches it into the call site. In some circumstances it would be nice
to be able to create the instruction and patch it later, and also some
code might want to check for errors in the branch creation before
doing the patching. A future commit will change create_branch() to
check for errors.
For callers that don't care, replace create_branch() with
patch_branch(), which just creates the branch and patches it directly.
While we're touching all the callers, change to using unsigned int *,
as this seems to match usage better. That allows (and requires) us to
remove the volatile in the definition of vector in powermac/smp.c and
mpc86xx_smp.c, that's correct because now that we're passing vector as
an unsigned int * the compiler knows that it's value might change
across the patch_branch() call.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently have a few routines for patching code in asm/system.h, because
they didn't fit anywhere else. I'd like to clean them up a little and add
some more, so first move them into a dedicated C file - they don't need to
be inlined.
While we're moving the code, drop create_function_call(), it's intended
caller never got merged and will be replaced in future with something
different.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, if we have a kernel with a 64kB page size, and some
process maps something that has to be mapped with 4kB pages (such as a
cache-inhibited mapping on POWER5+, or the eHCA infiniband queue-pair
pages), we change the process to use 4kB pages everywhere. This hurts
the performance of HPC programs that access eHCA from userspace.
With this patch, the kernel will only demote the slice(s) containing
the eHCA or cache-inhibited mappings, leaving the remaining slices
able to use 64kB hardware pages.
This also changes the slice_get_unmapped_area code so that it is
willing to place a 64k-page mapping into (or across) a 4k-page slice
if there is no better alternative, i.e. if the program specified
MAP_FIXED or if there is not sufficient space available in slices that
are either empty or already have 64k-page mappings in them.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to disable ptcal before starting a new kernel after a crash,
in order to avoid overwriting data in the kdump kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pseries_kexec_setup function overwrites some ppc_md
pointers, so make sure it only gets called when running on
the right architecture.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This converts ppc to use the new helpers for smp_call_function() and
friends, and adds support for smp_call_function_single().
ppc loses the timeout functionality of smp_call_function_mask() with
this change, as the generic code does not provide that.
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Ports B and C pins programming is changed to get SCC2 UART and FCC3
ethernet work.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new e500mc core from Freescale is based on the e500v2 but with the
following changes:
* Supports only the Enhanced Debug Architecture (DSRR0/1, etc)
* Floating Point
* No SPE
* Supports lwsync
* Doorbell Exceptions
* Hypervisor
* Cache line size is now 64-bytes (e500v1/v2 have a 32-byte cache line)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix this:
/usr/src/devel/arch/powerpc/platforms/pseries/eeh_driver.c: In function 'print_device_node_tree':
/usr/src/devel/arch/powerpc/platforms/pseries/eeh_driver.c:55: warning: ISO C90 forbids mixed declarations and code
also make that function look like it's part of Linux.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
of_node_put is needed before discarding a value received from
of_find_node_by_type, eg in error handling code.
The semantic patch that makes the change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct device_node *n;
struct device_node *n1;
struct device_node *n2;
statement S;
identifier f1,f2;
expression E1,E2;
constant C;
@@
n = of_find_node_by_type(...)
...
if (!n) S
... when != of_node_put(n)
when != n1 = f1(n,...)
when != E1 = n
when any
when strict
(
+ of_node_put(n);
return -C;
|
of_node_put(n);
|
n2 = f2(n,...)
|
E2 = n
|
return ...;
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is a delay in the transition to the stopped state for class 2
interrupts. In some cases, the controlling thread detects the state of
the spu as running, and goes back to sleep resulting in a hung
application as the event is missed.
This change detects the stop condition and re-generates the wakeup event
after a context save.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Time slicing can occur at the same time as spu exception handling
resulting in the wakeup of the wrong thread.
This change uses the the spu's register_lock to enforce synchronization
between bind/unbind and spu exception handling so that they are
mutually exclusive.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
According to the CBEA, the SPU dsisr is not updated for class 0
exceptions.
spu_stopped() is testing the dsisr that was passed to it from the class
0 exception handler, so we return a false positive here.
This patch cleans up the interrupt handler and erroneous tests in
spu_stopped. It also removes the fields from the csa since it is not
needed to process class 0 events.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
If the spu is stopping (ie, the SPU_STATUS_RUNNING bit is still set),
re-read the register to get the final stopped value.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
The Sam440ep is an high customizable general purpose mini-itx board,
based on the AMCC 440EP and with a LatticeXP FPGA onboard.
It's poduced by ACube Systems Srl (Bassano del Grappa, Italy),
http://www.acube-systems.biz.
Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The "ndfc-chip" device doesn't need any resources. All resources
are handled by the "ndfc-nand" device. Registering the same memory
resource twice causes "cat /proc/iomem" to go into an infinite loop
displaying NDFC memory addresses.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is patch adds board file, device tree, and defconfig for the new
board, made by Freescale Semiconductor Inc. and Logic Product Development.
Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.
Not supported in this patch:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM NAND driver);
2. FHCI USB (supported with FHCI driver).
3. QE Serial UCCs (tested to not work with ucc_uart driver, reason
unknown, yet);
4. ADC AD7843 (tested to work, but support via device tree depends on
major SPI rework, GPIO API, etc);
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the TQM8548 modules from TQ-Components
GmbH (http://www.tqc.de).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Like for the TQM5200, the vendor prefix "tqc," is now used for all
TQM85xx modules from TQ-Components GmbH (http://www.tqc.de) in the
corresponding DTS files.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC85xx MDS board requires some board level tweaks of the PHYs that
either the eTSEC (gianfar) or UCC ethernet controllers are connected to.
Its possible to build the phylib as a module, however this breaks the
board level fix ups because phy_read and phy_write are not available
if we build as a module.
So we unconditionally select PHYLIB to ensure its built into the kernel
if we are building in MPC85xx MDS support. This was determined to be
the easiest soultion even though it prevents the user from removing
PHYLIB support if they decide they don't want it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When I changed irq_alloc_host() to take an of_node
(52964f87c6: "Add an optional
device_node pointer to the irq_host"), I botched the reference
counting semantics.
Stephen pointed out that it's irq_alloc_host()'s business if
it needs to take an additional reference to the device_node,
the caller shouldn't need to care.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we do the call to irq_of_parse_and_map() first, then we don't
need to worry about freeing the irq_host.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 5 of 5: add the Kconfig entry for the C2K board.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 3 of 5: driver for the board. At this time it is very generic
and similar to its original, the driver for the prpmc2800.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following adds support for the Analogue & Micro ASP 8347E, running
Redboot.
http://www.analogue-micro.com/ASP8347.html
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch enabled MSI on 8544ds and 8572ds board.
So far only one MSI interrupt can generate on 8544 board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch enable the MSI on 8610hpcd board.
Through the msi-available-ranges property, All the 256
msi interrupts can be tested on this board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Switched from 64M NOR/64M NAND to 4M NOR/256M NAND.
* Full DTM support including critical temperature.
* Added POST information.
* Removed LED function, moved to new LED driver.
* Moved ad7414 to new style I2C initialization.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds full support for ftrace for PowerPC (both 64 and 32 bit).
This includes dynamic tracing and function filtering.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A change was made to walk_memory_resource() in commit
4b119e21d0 that added a
check of find_lmb(). Add the coresponding lmb_add()
call to ps3_mm_add_memory() so that that check will
succeed.
This fixes the condition where the PS3 boots up with
only the 128 MiB of boot memory, and doesn't see the
other 128MiB that is available.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds some debugging code to the Axon MSI driver. It creates a
file per MSIC in /sys/kernel/debug/powerpc, which allows the user to
trigger a fake MSI interrupt by writing to the file.
This can be used to test some of the MSI generation path. In
particular, that the MSIC recognises a write to the MSI address,
generates an interrupt and writes the MSI packet into the ring buffer.
All the code is inside #ifdef DEBUG so it causes no harm unless it's
enabled.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The old device/driver matching scheme is going away so stop using it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Olof Johansson <olof@lixom.net>
Fix following warnings:
WARNING: arch/powerpc/platforms/cell/built-in.o(.devinit.text+0x9c): Section mismatch in reference from the function .cell_setup_phb() to the function .init.text:.iowa_register_bus()
WARNING: arch/powerpc/platforms/cell/built-in.o(.devinit.text+0xa4): Section mismatch in reference from the function .cell_setup_phb() to the function .init.text:.io_workaround_init()
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With CONFIG_VIRT_CPU_ACCOUNTING disabled, I got the following error:
linux-2.6/arch/powerpc/platforms/cell/spufs/file.c: In function 'spu_switch_log_notify':
linux-2.6/arch/powerpc/platforms/cell/spufs/file.c:2542: error: implicit declaration of function 'get_tb'
make[4]: *** [arch/powerpc/platforms/cell/spufs/file.o] Error 1
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If victim (not ctx) is in spu_run, add victim to rq.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Don't return void in pseries/iommu.c
Make mce_data_buf static in pseries/ras.c
Make things static in pseries/rtasd.c
Make things static in pseries/setup.c
vtermno may as well be static in platforms/pseries/lpar.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The declaration for fw_feature_init() is in pseries.h and
implemented in firmware.c, so the latter should include the
former.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make a few things static in lparcfg.c
Make init and exit routines static in rtas_flash.c
Make things static in rtas_pci.c
Make some functions static in rtas.c
Make fops static in rtas-proc.c
Remove unneeded extern for do_gtod in smp.c
Make clocksource_init() static in time.c
Make last_tick_len and ticklen_to_xs static in time.c
Move the declaration of the pvr per-cpu into smp.h
Make kexec_smp_down() and kexec_stack static in machine_kexec_64.c
Don't return void in arch_teardown_msi_irqs() in msi.c
Move declaration of GregorianDay()into asm/time.h
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The typdef for irqreturn_t was moved into its own header a
while back, so there's no reason we can't move xmon_irq()
into xmon.h now.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following adds local bus, flash and MTD partition nodes for
sbc8548. As well, a compatible field for the soc node, so that
of_platform_bus_probe() will pick it up.
Something that is provided through this newly added epld node
is the Hardware Revision which is now being utilized.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DIU platform code should not just write to the PIXIS' BRDCFG0 register,
it should set and clear its own bits only, otherwise it will break
firmware setup (in fact it breaks second uart).
Also get rid of magic numbers in the related code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds device tree nodes for NOR and NAND flashes and places
board-control node inside the localbus.
defconfig and board file updated appropriately.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The 8568 MDS needs some configuration changes to the PHY in order to
work properly. These are done in the firmware, normally, but Linux
shouldn't need to rely on the firmware running such things (someone
could disable the PHY support in the firmware to save space, for instance).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (23 commits)
[POWERPC] Remove leftover printk in isa-bridge.c
[POWERPC] Remove duplicate #include
[POWERPC] Initialize lockdep earlier
[POWERPC] Document when printk is useable
[POWERPC] Fix bogus paca->_current initialization
[POWERPC] Fix of_i2c include for module compilation
[POWERPC] Make default cputable entries reflect selected CPU family
[POWERPC] spufs: lockdep annotations for spufs_dir_close
[POWERPC] spufs: don't requeue victim contex in find_victim if it's not in spu_run
[POWERPC] 4xx: Fix PCI mem in sequoia DTS
[POWERPC] 4xx: Add endpoint support to 4xx PCIe driver
[POWERPC] 4xx: Fix problem with new TLB storage attibute fields on 440x6 core
[POWERPC] spufs: spu_create should send inotify IM_CREATE event
[POWERPC] spufs: handle faults while the context switch pending flag is set
[POWERPC] spufs: fix concurrent delivery of class 0 & 1 exceptions
[POWERPC] spufs: try to route SPU interrupts to local node
[POWERPC] spufs: set SPU_CONTEXT_SWITCH_PENDING before synchronising SPU irqs
[POWERPC] spufs: don't acquire state_mutex interruptible while performing callback
[POWERPC] spufs: update master runcntl with context lock held
[POWERPC] spufs: fix post-stopped update of MFC_CNTL register
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
net: Added ASSERT_RTNL() to dev_open() and dev_close().
can: Fix can_send() handling on dev_queue_xmit() failures
netns: Fix arbitrary net_device-s corruptions on net_ns stop.
netfilter: Kconfig: default DCCP/SCTP conntrack support to the protocol config values
netfilter: nf_conntrack_sip: restrict RTP expect flushing on error to last request
macvlan: Fix memleak on device removal/crash on module removal
net/ipv4: correct RFC 1122 section reference in comment
tcp FRTO: SACK variant is errorneously used with NewReno
e1000e: don't return half-read eeprom on error
ucc_geth: Don't use RX clock as TX clock.
cxgb3: Use CAP_SYS_RAWIO for firmware
pcnet32: delete non NAPI code from driver.
fs_enet: Fix a memory leak in fs_enet_mdio_probe
[netdrvr] eexpress: IPv6 fails - multicast problems
3c59x: use netstats in net_device structure
3c980-TX needs EXTRA_PREAMBLE
fix warning in drivers/net/appletalk/cops.c
e1000e: Add support for BM PHYs on ICH9
uli526x: fix endianness issues in the setup frame
uli526x: initialize the hardware prior to requesting interrupts
...
We need to acquire the parent i_mutex with I_MUTEX_PARENT to keep
lockdep happy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
We should not requeue the victim context in find_victim if the owner is
not in spu_run. It's first not needed because leaving the context on
the spu is an optimization and second is harmful because it means the
owner could re-enter spu_run when the context is on the runqueue and
trip the BUG_ON in __spu_update_sched_info.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Creating a spufs context or gand using spu_create should send an inotify
event so that things like performance monitors have an easy way to find
out about newly created contexts.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Simply replace proc_create and further data assigned with proc_create_data.
No need to check for data!=NULL after that.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Alexey Dobriyan <adobriyan@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, page fault handlers don't issue a mfc restart if the context
switch pending flag is set, which can leave us with a hanging DMA after
a context restore.
This patch introduces fault pending flag that is set by the fault
handler and read by the context switch code, so that the latter can add
the restart bit at the right spot, after it has successfuly saved the
state of the mfc control register.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
SPU class 0 & 1 exceptions may occur in parallel, so we may end up
overwriting csa.dsisr.
This change adds dedicated fields for each class to the spu and the spu
context so that fault data is not overwritten.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we re-route SPU interrupts to the current cpu, which may be
on a remote node. In the case of time slicing, all spu interrupts will
end up routed to the same cpu, where the spusched_tick occurs.
This change routes mfc interrupts to the cpu where the controlling
thread last ran, provided that cpu is on the same node as the spu
(otherwise don't reroute interrupts).
This should improve performance and provide a more predictable
environment for processing spu exceptions. In the past we have seen
concurrent delivery of spu exceptions to two cpus. This eliminates that
concern.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
synchronize_irq() provides the serialization for
SPU_CONTEXT_SWITCH_PENDING which is read with a simple load. This
routine guarantees that the relevant interrupt handlers are not running,
so that the next time they do run they will see the update
memory value.
This must be done correctly so that exception handling code does not
restart the mfc in the middle of a context switch while we are trying
to atomically stop it and save state.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
There's currently no way to tell if spu_process_callback has
returned with the state mutex held, as -EINTR may be returned
by either the syscall or the spu_acquire fail case.
Instead, just do a non-interruptible mutex_lock here.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we update the SPU master run control bit (ie,
spu_enable_spu) in spufs_run_spu before we grab the context mutex. This
can result in races with other processes accessing this context's
resources.
This change moves the spu_enable_spu to after we have acquired the
context lock.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
We currently have two issues with the MFC save code:
* save_mfc_decr doesn't handle a transition of 1 -> 0 of the Ds bit
* The Q bit may be stale in the CSA
This change fixes the first issue by clearing the relevant bits from
the MFC_CNTL value in the CSA before or-ing in the updated status.
Also, we add the Q bit to the updated status.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we can introduce invalid entries into the MFC queues:
1) context starts a DMA
2) context gets scheduled out during a DMA
- kernel saves MFC queue to CSA
- kernel saves 0x0 in csa->mfc_control_RW
3) context gets scheduled in
- csa->mfc_control[Q] ('queues empty') isn't set, so DMA queues are
restored from the CSA
4) context's DMA is completed
5) context gets scheduled out again, no DMA occuring this time
- kernel sees that MFC_CNTL[Q] ('queues empty') is set, so doesn't
touch saved queue data in CSA
- kernel saves 0x0 in csa->mfc_control_RW
6) context gets scheduled in
- csa->mfc_control[Q] ('queues empty') isn't set (we saved is as 0!),
so DMA queues are restored from the CSA
In this last restore, we've restored the queue status from step 2,
which are now invalid.
This change makes save_mfc_cntl() closer to the save/restore sequence,
as specified in the CBE handbook.
With changes from Luke Browning.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
When we issue a MFC purge request, we may inadvertantly clear the
suspended status.
This change adds the MFC_CNTL_SUSPEND_MASK when we issue a purge
request, so that the suspend bit is masked out.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
We may currently lose interrupts during SPE context switch, as we alter
the INT_Route register. Because the IIC uses a per-thread priority
status, changing the interrupt routing to a different thread means that
the IRQ is no longer masked by the priority status, so we end up with
two fasteoi IRQ handlers executing for the one irq_desc. The fasteoi
handler doesn't handle multiple IRQs, so drops the second one.
Fix this by using our own flow handler. This is based on
handle_edge_irq, but issues an eoi after IRQs are handled, and doesn't
do any mask/unmasking.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
[POWERPC] PS3: Update ps3_defconfig
[POWERPC] PS3: Remove unsupported wakeup sources
[POWERPC] PS3: Make ps3_virq_setup and ps3_virq_destroy static
[POWERPC] PS3: Add time include to lpm
[POWERPC] Fix slb.c compile warnings
[POWERPC] Xilinx: Fix compile warnings
[POWERPC] Squash build warning for print of resource_size_t in fsl_soc.c
[RAPIDIO] fix current kernel-doc notation
[POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
Fix a potential issue in mpc52xx uart driver
[POWERPC] mpc5200: Allow for fixed speed MII configurations
[POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board
The routines ps3_virq_setup() and ps3_virq_destroy() are used
in only one file, so make them static.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The sputrace module contained a trace entry for spu_acquire_saved, but
this marker was not placed anywhere. Fix this by adding a marker to the
routine.
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Fix a typo in the marker for the find_victim function, which prevented
it from being traced. It previously read find_vitim.
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
The sputrace module contained a reference to a marker for
destroy_spu_context, but this marker did not appear in the code. Fix
this by adding a marker in the function.
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
The markers facility defines the marker parameters to be of the form
'name %format'. Add parameter names to sputrace, to specify the context
and %spu paramerters, instead of just specifying the '%format' part.
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
There are userspace instrumentation tools that need to monitor spu
context switches. This patch adds a new file called 'switch_log' to
each spufs context directory that can be used to monitor the context
switches.
Context switch in/out and exit from spu_run are monitored after the
file was first opened and can be read from it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[RAPIDIO] Change RapidIO doorbell source and target ID field to 16-bit
[RAPIDIO] Add RapidIO connection info print out and re-training for broken connections
[RAPIDIO] Add serial RapidIO controller support, which includes MPC8548, MPC8641
[RAPIDIO] Add RapidIO node probing into MPC86xx_HPCN board id table
[RAPIDIO] Add RapidIO node into MPC8641HPCN dts file
[RAPIDIO] Auto-probe the RapidIO system size
[RAPIDIO] Add OF-tree support to RapidIO controller driver
[RAPIDIO] Add RapidIO multi mport support
[RAPIDIO] Move include/asm-ppc/rio.h to asm-powerpc
[RAPIDIO] Add RapidIO option to kernel configuration
[RAPIDIO] Change RIO function mpc85xx_ to fsl_
[POWERPC] Provide walk_memory_resource() for powerpc
[POWERPC] Update lmb data structures for hotplug memory add/remove
[POWERPC] Hotplug memory remove notifications for powerpc
[POWERPC] windfarm: Add PowerMac 12,1 support
[POWERPC] Fix building of pmac32 when CONFIG_NVRAM=m
[POWERPC] Add IRQSTACKS support on ppc32
[POWERPC] Use __always_inline for xchg* and cmpxchg*
[POWERPC] Add fast little-endian switch system call
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Add correct ->owner to proc_fops to fix reading/module unloading race.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add board support for the Phytec pcm030 mpc5200b based board. It
does not need any platform specific fixups and as such is handled
as a mpc5200 simple platform.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds gpiolib support for mpc5200 SOCs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a set_type function for external (GPIO) interrupts.
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The powerpc kernel maintains information about logical memory blocks
in the lmb.memory structure, which is initialized and updated at boot
time, but not when memory is added or removed while the kernel is
running.
This adds a hotplug memory notifier which updates lmb.memory when
memory is added or removed. This information is useful for eHEA
driver to find out the memory layout and holes.
NOTE: No special locking is needed for lmb_add() and lmb_remove().
Calls to these are serialized by caller. (pSeries_reconfig_chain).
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Hotplug memory remove notifier for 64-bit powerpc. This gets invoked
by writing to /proc/ppc64/ofdt the string "remove_node " followed by
the firmware device tree pathname of the node that needs to be removed.
In response, this adjusts the sections and removes sysfs entries by
calling __remove_pages(). Then it calls arch-specific code to get rid
of the hardware MMU mappings for the section of memory.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Reviewed-by: Michael Ellerman <michael@ellerman.id.au>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Kamalesh Babulal (kamalesh@linux.vnet.ibm.com) reports that CONFIG_NVRAM=m
is valid in terms of Kconfig but fails to build with:
Building modules, stage 2.
MODPOST 1401 modules
ERROR: "pmac_newworld" [arch/powerpc/platforms/powermac/nvram.ko] undefined!
ERROR: "__alloc_bootmem" [arch/powerpc/platforms/powermac/nvram.ko] undefined!
make[1]: *** [__modpost] Error
The arch/powerpc/platforms/powermac/nvram.c code really needs to be
builtin, but as its compilation is dependent on a generic Kconfig
symbol we force nvram.c to be builtin if CONFIG_NVRAM is 'y' or 'm'.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move mv643xx_eth's static state (ethernet register block base address
and MII management interface spinlock) into a struct hanging off the
shared platform device. This is necessary to support chips that
contain multiple mv643xx_eth silicon blocks.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Add platform code to support Freescale DIU. The platform code includes
framebuffer memory allocation, pixel format, monitor port, etc.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for PCI Express port on Celleb. I/O space of this
PCI Express port is not mapped in memory space. So we use the
io-workaround mechanism to make accesses indirect.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves miscellaneous files for Beat into platforms/cell/.
All files in this patch are used by celleb-beat only.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves SPU support code on Beat into platforms/cell/.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves files for mmu and iommu on Beat into platforms/cell/.
All files in this patch are used by celleb-beat only.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves files for Beat hvcall interfaces into platforms/cell/.
All files in this patch are used by celleb-beat only.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the SCC (Super Companion Chip) related code for celleb
into platforms/cell/.
All files in this patch are used by celleb-beat and celleb-native
commonly.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
