correct GPIO freed in treo680_irda_shutdown()
Signed-off-by: Tomáš ?ech <sleep_walker@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If CONFIG_APM_EMULATION=n em-x270 build fails with linker error:
arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_critical': em-x270.c:(.text+0x12c0): undefined reference to `apm_queue_event'
arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_low': em-x270.c:(.text+0x12c8): undefined reference to `apm_queue_event'
make: *** [.tmp_vmlinux1] Error 1
Fix it.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
WARNING: at drivers/gpio/gpiolib.c:83 gpio_ensure_requested+0x58/0xbc()
autorequest GPIO-71
Modules linked in:
[<c0028bd0>] (unwind_backtrace+0x0/0xe8) from [<c003c328>] (warn_slowpath_common+0x48/0x78)
[<c003c328>] (warn_slowpath_common+0x48/0x78) from [<c003c394>] (warn_slowpath_fmt+0x28/0x38)
[<c003c394>] (warn_slowpath_fmt+0x28/0x38) from [<c0146128>] (gpio_ensure_requested+0x58/0xbc)
[<c0146128>] (gpio_ensure_requested+0x58/0xbc) from [<c0146308>] (gpio_direction_input+0x80/0xf4)
[<c0146308>] (gpio_direction_input+0x80/0xf4) from [<c000c668>] (zylonite_pxa300_init+0x108/0x214)
[<c000c668>] (zylonite_pxa300_init+0x108/0x214) from [<c000c4e4>] (zylonite_init+0x8/0x84)
[<c000c4e4>] (zylonite_init+0x8/0x84) from [<c00097cc>] (customize_machine+0x18/0x24)
[<c00097cc>] (customize_machine+0x18/0x24) from [<c00222e0>] (do_one_initcall+0x30/0x1b0)
[<c00222e0>] (do_one_initcall+0x30/0x1b0) from [<c00083f4>] (kernel_init+0xa4/0x11c)
[<c00083f4>] (kernel_init+0xa4/0x11c) from [<c0023f3c>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1b75b31a2719ed1c ]---
This issue is caused by using gpio pin without request. Add gpio_request()
into zylonite. To simplify the code, error checking is omitted since this
is being performed early.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Attepmpt to configure ULPI pins gives the following compile error:
CC arch/arm/mach-pxa/cm-x300.o
arch/arm/mach-pxa/cm-x300.c:155: error: 'MFP_MFP_AF0' undeclared here (not in a function)
arch/arm/mach-pxa/cm-x300.c:155: error: 'MFP_MFP_DS01X' undeclared here (not in a function)
make[2]: *** [arch/arm/mach-pxa/cm-x300.o] Error 1
make[1]: *** [arch/arm/mach-pxa] Error 2
make: *** [sub-make] Error 2
Fix it.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In commit f23d491131, the pwr-i2c device name changed due to the
newly introduced device table. This patch fixes the clock so the
driver's probe will succeed again.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Currently pcm990 camera bus-width management functions request a GPIO and never
free it again. With this approach the GPIO extender driver cannot be unloaded
once camera drivers have been loaded, also unloading theb i2c-pxa bus driver
produces errors, because the GPIO extender driver cannot unregister properly.
Another problem is, that if camera drivers are once loaded before the GPIO
extender driver, the platform code marks the GPIO unavailable and only a reboot
helps to recover. Adding an explicit free_bus method and using it in mt9m001
and mt9v022 drivers fixes these problems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The wm8731 driver has been converted to register using the standard I2C
device registration mechanism so we can now do the registration in the
arch/arm code as normal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Maxim 1586 V3 gain can be configured by external resistors
(R24, R25) connected to the FB3 pin. To avoid accidental
overvoltage, it now requires this gain to be configured
explicitly.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
On this board, the PXA272 CPU voltage VCC_CORE is provided
by a Maxim 1586 voltage regulator. Use the regulator
framework to provide VCC_CORE control. When cpufreq will be
updated to ask for vcc_core, this will optimize power
drained by the board.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
On this board, the PXA270 CPU voltage VCC_CORE is provided
by a Maxim 1587A voltage regulator configured to provide
1.55 V maximum voltage for 624 MHz operation.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
After commit 6b849bcff0 (ASoC: Convert PXA
AC97 driver to probe with the platform device) AC97 controller device
should be registered explicitly for both ASoC and generic AC97 drivers
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Register userspace-consumer devices to allow userspace control of
voltage regulators supplying GPS and GPRS modules
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
For suspend/resume to work, spitz needs pxa_pm_suspend/resume to be
called. Otherwise PSPR is not set properly, and system will die during
resume.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Replace calls to pxa_gpio_mode with respective gpio_request() /
gpio_direction_input(). In principle these calls can be dropped as
the only use of those GPIO are IRQs and IRQ code does setup GPIO
correctly.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
As pxa now is the only user of sharpsl_pm we can drop several startup
functions into generic code thus dropping several global functions.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
collie_pm was the only non-PXA user of sharpsl_pm. Now as it's gone we
can merge code into one single file to allow further cleanup.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
CM-X300 can be assembled with different NAND flashes from different
manufacturers. Adding their configuration to the kernel is impractical,
therefore we will use the default NAND controller settings set up by the
bootloader.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Setup gpio-keys for EzX phones
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add a call to pxa_set_ac97_info() to enable the audio support.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
csb726 used obsolete and not working out-of-tree driver smc911x.
Switch it to use new smsc911x driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
