Improve power management and error handling by using pci_set_power_state(),
instead of driver doing PCI PM register changes in the driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the NETIF_F_TSO #ifdef-ery in drivers/net; this was
for old-old-2.4 compat (even current 2.4 has NETIF_F_TSO)
but it's time to get rid of it by now.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add some debugging and error printing.
The show_rx_chain() prints out the status of the rx chain,
which shows that the status of the descriptors gets
messed up after the second & subsequent RX ramfulls.
Print out contents of bad packets if error occurs.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Delete possible source of chain corruption; the hardware
already knows the location of the tail, and writing it
again is likely to mess it up.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add memory barrier to make sure that the rest of the
RX descriptor state is flushed to memory before we tell
the hardware that its ready to go.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tell the hardware the location of the rx ring tail.
More punctuation cleanup.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unused variable; this makes code easier to read.
Tweak commentary.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The invocation of the rx ring refill routine is haphazard,
it can be called from a central location.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify the somewhat convoluted use of return codes
in the rx buffer handling.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Another skb leak in an error branch. Fix this by adding
call to dev_kfree_skb_irq() after moving to a more
appropriate spot.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
One of the unlikely error branches has an skb memory leak.
Fix this by handling the error conditions consistently.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is no need to pass a flag into spider_net_decode_one_descr()
so remove this, and perform some othre minor cleanup.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Get rid of the rxramfull tasklet, and let the NAPI poll routine
deal with this situation. (The rxramfull interrupt is simply
stating that the h/w has run out of room for incoming packets).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds net_ratelimit to many of the printks in order to
limit extraneous warning messages (created in response to Bug 28554).
This patch supercedes all previous ratelimit patches.
This has been tested, please apply.
From: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Linas Vepstas <jlinas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current driver code performs 512 DMA mappings of a bunch of
32-byte ring descriptor structures. This is silly, as they are
all in contiguous memory. This patch changes the code to
dma_map_coherent() each rx/tx ring as a whole.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: James K Lewis <jklewis@us.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Let's try to avoid some code duplication.
- cxgb2
The data are contiguous. Use plain memcpy.
- ixf1010/pm3393/vsc7326
The cast of &mac->stats to (u64 *) is not wonderful but it is not clear
if it is worth to add an ad-hoc union under the struct cmac_statistics.
vsc7326_reg.h suggests that more statistics could be available.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
- duplicated code in sge::free_cmdQ_buffers ;
- NET_IP_ALIGN is already defined in (included) <linux/skbuff.h> ;
- pci_alloc_consistent() returns void * ;
- pci_alloc_consistent() returns a zeroed chunk of memory ;
- early return in restart_tx_queues.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
pci_get_drvadata() is necessarily distinct from NULL if
cxgb2::init_one succeeded. cxgb2::remove_one is solely
issued through the PCI device callback.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
This patch add ipw2200 support for iwconfig rts/frag auto.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Marijn Schouten
zd1211b chip 0586:340f v4810 high 00-13-49 AL2230_RF pa0 g---
FCC ID: I88G220V2
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for "ethtool -i" to prism54 driver.
ethtool -i queries the specified device for
associated driver information.
This helps tools like Fedora's system-config-network to
provide GUI management of network devices.
I learned how to write this patch by reading the ipw2100
driver code.
Signed-off-by: Kai Engert <kengert@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current bcm43xx driver ignores any wireless-enable switches on mini-PCI
and mini-PCI-E cards. This patch implements a new routine to interrogate the
radio hardware enabled bit in the interface, logs the initial state and any
changes in the switch (if debugging enabled), activates the LED to show the
state, and changes the periodic work handler to provide 1 second response
to switch changes and to account for changes in the periodic work specs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Henrik Hjelte
zd1211b chip 13b1:0024 v4802 high 00-14-bf AL2230_RF pa0 ----
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of passing our own custom 32-bit addresses around and
translating them, this patch makes all our register address constants
absolute and removes the translation.
There are two ugly parts:
- fw_reg_addr() is needed to compute addresses of firmware registers, as this
is dynamic based upon firmware
- inc_addr() needs a small hack to handle byte vs word addressing
However, both of those are only small, and we don't use fw_regs a whole
lot anyway.
The bonuses here include simplicity and improved driver readability. Also, the
fact that registers are now referenced by 16-bit absolute addresses (as
opposed to 32-bit pseudo addresses) means that over 2kb compiled code size has
been shaved off.
Includes some touchups and sparse fixes from Ulrich Kunitz.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The zd1211rw address space has confused me once too many times. This
patch introduces the following naming notation:
Memory space is split into segments (cr, fw, eeprom) and segments may
contain components (e.g. boot code inside eeprom). These names are
arbitrary and only for the description below:
x_START: Absolute address of segment start
(previously these were named such as CR_BASE_OFFSET, but they weren't
really offsets unless you were considering them as an offset to 0)
x_LEN: Segment length
x_y_LEN: Length of component y of segment x
x_y_OFFSET: Relative address of component y into segment x. The absolute
address for this component is (x_START + x_y_OFFSET)
I also renamed EEPROM registers to EEPROM data. These 'registers' can't
be written to using standard I/O and really represent predefined data
from the vendor.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many of the registers written during ZD1211 HMAC initialization are
duplicated exactly for ZD1211B. Move the identical ones into a generic
part, and write the hardware-specific ones separately.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver was still mis-calculating the number of bytes sent during
transmit, now the driver computes what appears to be exactly 100%
correct byte counts (not including CRC) when figuring out how many
bytes and frames were sent during the current transmit packet.
Since the driver sets the IP checksum insertion bit (IXSM in Status
field) in transmit context descriptors, it should clear the IP checksum
bits of any garbage so as not to confuse the hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Print RX/TX flow control setting at link up time to display the
actual link FC properties instead of the advertised values.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This fix attempts to solve a customer (IBM) reported issue with NAPI
enabled e1000 having bad performance when transmitting simultaneously
on four ports. The issue comes down to an interaction between NAPI,
hardware interrupt balancing, and the driver rescheduling poll on
the same processor. Try to fix by allowing the driver to re-enable
interrupts sooner instead of polling one more time, when there was
recently all the work completed in cleanup.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Unfortunately the read-free MSI interrupt handler needs to flush write
the icr register and thus we can't be read-free. Our MSI irq routine
thus becomes a lot more simpler since we don't need to track link state
anymore.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
smc911x_phy_configure's error handling unconditionally unlocks the
spinlock even if it wasn't locked. Patch fixes it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We forget to call spider_net_free_rx_chain_contents which does the
actual dev_kfree_skb. New skbs are allocated from skbuff_head_cache
on each "ifconfig up" letting the cache grow infinitely.
This patch fixes it.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
e100: fix napi ifdefs removing needed code
From: Auke Kok <auke-jan.h.kok@intel.com>
The e100 driver is NAPI mode only. We need to netif_poll_disable
during suspend and shutdown. The non-NAPI driver code was removed
and is only avaiable in the out-of-tree e100 kernel driver.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
5709 A0 copper devices will not link up with some link partners
without this workaround.
Update driver to 1.5.5.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Won't build (request_irq()/free_irq()), even if you manage to find an
s390 box with 8250-compatible UART they are expecting.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 0c0b3ae68e.
Quoth David:
"Jeff, please revert
It's wrong. We had a lengthy analysis of this piece of code
several months ago, and it is correct.
Consider, if we run the loop and we get an error
the following happens:
1) attempt of ifb_init_one(i) fails, therefore we should
not try to "ifb_free_one()" on "i" since it failed
2) the loop iteration first increments "i", then it
check for error
Therefore we must decrement "i" twice before the first
free during the cleanup. One to "undo" the for() loop
increment, and one to "skip" the ifb_init_one() case which
failed."
Reported-by: David Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some issues in b44_resume().
- Return value of pci_enable_device() was ignored.
- If request_irq() has failed we have to just disable device and exit.
Signed-off-by: Dmitriy Monakhov <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
