Fix warning from pmd_bad() at bootup on a HIGHMEM64G HIGHPTE x86_32.
That came from 9fc34113f6 x86: debug pmd_bad();
but we understand now that the typecasting was wrong for PAE in the previous
version: pagetable pages above 4GB looked bad and stopped Arjan from booting.
And revert that cded932b75 x86: fix pmd_bad
and pud_bad to support huge pages. It was the wrong way round: we shouldn't
weaken every pmd_bad and pud_bad check to let huge pages slip through - in
part they check that we _don't_ have a huge page where it's not expected.
Put the x86 pmd_bad() and pud_bad() definitions back to what they have long
been: they can be improved (x86_32 should use PTE_MASK, to stop PAE thinking
junk in the upper word is good; and x86_64 should follow x86_32's stricter
comparison, to stop thinking any subset of required bits is good); but that
should be a later patch.
Fix Hans' good observation that follow_page() will never find pmd_huge()
because that would have already failed the pmd_bad test: test pmd_huge in
between the pmd_none and pmd_bad tests. Tighten x86's pmd_huge() check?
No, once it's a hugepage entry, it can get quite far from a good pmd: for
example, PROT_NONE leaves it with only ACCESSED of the KERN_PGTABLE bits.
However... though follow_page() contains this and another test for huge
pages, so it's nice to keep it working on them, where does it actually get
called on a huge page? get_user_pages() checks is_vm_hugetlb_page(vma) to
to call alternative hugetlb processing, as does unmap_vmas() and others.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Earlier-version-tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeff Chua <jeff.chua.linux@gmail.com>
Cc: Hans Rosenfeld <hans.rosenfeld@amd.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/x86/pci/Makefile_32 has a nasty detail. VISWS and NUMAQ build
override the generic pci-y rules. This needs a proper cleanup, but
that needs more thoughts. Undo
commit 895d30935e
x86: numaq fix
do not override the existing pci-y rule when adding visws or
numaq rules.
There is also a stupid init function ordering problem vs. acpi.o
Add comments to the Makefile to avoid tripping over this again.
Remove the srat stub code in discontig_32.c to allow a proper NUMAQ
build.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
bdd3cee2e4 (x86: ioremap(), extend check
to all RAM pages) breaks OLPC's ioremap call. The ioremap that OLPC uses is:
romsig = ioremap(0xffffffc0, 16);
The commit that breaks it is basically:
- for (pfn = phys_addr >> PAGE_SHIFT; pfn < max_pfn_mapped &&
- (pfn << PAGE_SHIFT) < last_addr; pfn++) {
+ for (pfn = phys_addr >> PAGE_SHIFT;
+ (pfn << PAGE_SHIFT) < last_addr; pfn++) {
+
Previously, the 'pfn < max_pfn_mapped' check would've caused us to not
enter the loop. Removing that check means we loop infinitely. The
reason for that is because pfn is 0xfffff, and last_addr is 0xffffffcf.
The remaining check that is used to exit the loop is not sufficient;
when pfn<<PAGE_SHIFT is 0xfffff000, that is less than 0xffffffcf; when
we increment pfn and it overflows (pfn == 0x100000), pfn<<PAGE_SHIFT
ends up being 0. That, of course, is less than last_addr. In effect,
pfn<<PAGE_SHIFT is never lower than last_addr.
The simple fix for this is to limit the last_addr check to the PAGE_MASK;
a patch is below.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use UC_MINUS for ioremap(), ioremap_nocache() instead of strong UC.
Once all the X drivers move to ioremap_wc(), we can go back to strong
UC semantics for ioremap() and ioremap_nocache().
To avoid attribute aliasing issues, pci_mmap_page_range() will also
use UC_MINUS for default non write-combining mapping request.
Next steps:
a) change all the video drivers using ioremap() or ioremap_nocache()
and adding WC MTTR using mttr_add() to ioremap_wc()
b) for strict usage, we can go back to strong uc semantics
for ioremap() and ioremap_nocache() after some grace period for
completing step-a.
c) user level X server needs to use the appropriate method for setting
up WC mapping (like using resourceX_wc sysfs file instead of
adding MTRR for WC and using /dev/mem or resourceX under /sys)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Vegard Nossum reported a large (150 seconds) boot delay during bootup,
and bisected it to "x86: ioremap(), extend check to all RAM pages"
(commit bdd3cee2e4). Revert this commit for now.
Bisected-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch removes the no longer used export of kmap_atomic_to_page.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-pci:
x86: add pci=check_enable_amd_mmconf and dmi check
x86: work around io allocation overlap of HT links
acpi: get boot_cpu_id as early for k8_scan_nodes
x86_64: don't need set default res if only have one root bus
x86: double check the multi root bus with fam10h mmconf
x86: multi pci root bus with different io resource range, on 64-bit
x86: use bus conf in NB conf fun1 to get bus range on, on 64-bit
x86: get mp_bus_to_node early
x86 pci: remove checking type for mmconfig probe
x86: remove unneeded check in mmconf reject
driver core: try parent numa_node at first before using default
x86: seperate mmconf for fam10h out from setup_64.c
x86: if acpi=off, force setting the mmconf for fam10h
x86_64: check MSR to get MMCONFIG for AMD Family 10h
x86_64: check and enable MMCONFIG for AMD Family 10h
x86_64: set cfg_size for AMD Family 10h in case MMCONFIG
x86: mmconf enable mcfg early
x86: clear pci_mmcfg_virt when mmcfg get rejected
x86: validate against acpi motherboard resources
Fixed up fairly trivial conflicts in arch/x86/pci/{init.c,pci.h} due to
OLPC support manually.
All architectures use an effectively identical definition of online_page(), so
just make it common code. x86-64, ia64, powerpc and sh are actually
identical; x86-32 is slightly different.
x86-32's differences arise because it puts its hotplug pages in the highmem
zone. We can handle this in the generic code by inspecting the page to see if
its in highmem, and update the totalhigh_pages count appropriately. This
leaves init_32.c:free_new_highpage with a single caller, so I folded it into
add_one_highpage_init.
I also removed an incorrect comment referring to the NUMA case; any NUMA
details have already been dealt with by the time online_page() is called.
[akpm@linux-foundation.org: fix indenting]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamez.hiroyu@jp.fujitsu.com>
Tested-by: KAMEZAWA Hiroyuki <kamez.hiroyu@jp.fujitsu.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Christoph Lameter <clameter@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo already fixed one of these at my request (in "x86 PAT: tone down
debugging messages", commit 1ebcc654f0),
but there was another one he missed.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[mingo@elte.hu: split from "x86_64: get boot_cpu_id as early for k8_scan_nodes]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On big systems with lots of memory, don't print out too much during
bootup, and make it easy to find if it is continuous.
on 256G 8 sockets system will get
[ffffe20000000000-ffffe20002bfffff] PMD -> [ffff810001400000-ffff810003ffffff] on node 0
[ffffe2001c700000-ffffe2001c7fffff] potential offnode page_structs
[ffffe20002c00000-ffffe2001c7fffff] PMD -> [ffff81000c000000-ffff8100255fffff] on node 0
[ffffe20038700000-ffffe200387fffff] potential offnode page_structs
[ffffe2001c800000-ffffe200387fffff] PMD -> [ffff810820200000-ffff81083c1fffff] on node 1
[ffffe20040000000-ffffe2007fffffff] PUD ->ffff811027a00000 on node 2
[ffffe20038800000-ffffe2003fffffff] PMD -> [ffff811020200000-ffff8110279fffff] on node 2
[ffffe20054700000-ffffe200547fffff] potential offnode page_structs
[ffffe20040000000-ffffe200547fffff] PMD -> [ffff811027c00000-ffff81103c3fffff] on node 2
[ffffe20070700000-ffffe200707fffff] potential offnode page_structs
[ffffe20054800000-ffffe200707fffff] PMD -> [ffff811820200000-ffff81183c1fffff] on node 3
[ffffe20080000000-ffffe200bfffffff] PUD ->ffff81202fa00000 on node 4
[ffffe20070800000-ffffe2007fffffff] PMD -> [ffff812020200000-ffff81202f9fffff] on node 4
[ffffe2008c700000-ffffe2008c7fffff] potential offnode page_structs
[ffffe20080000000-ffffe2008c7fffff] PMD -> [ffff81202fc00000-ffff81203c3fffff] on node 4
[ffffe200a8700000-ffffe200a87fffff] potential offnode page_structs
[ffffe2008c800000-ffffe200a87fffff] PMD -> [ffff812820200000-ffff81283c1fffff] on node 5
[ffffe200c0000000-ffffe200ffffffff] PUD ->ffff813037a00000 on node 6
[ffffe200a8800000-ffffe200bfffffff] PMD -> [ffff813020200000-ffff8130379fffff] on node 6
[ffffe200c4700000-ffffe200c47fffff] potential offnode page_structs
[ffffe200c0000000-ffffe200c47fffff] PMD -> [ffff813037c00000-ffff81303c3fffff] on node 6
[ffffe200c4800000-ffffe200e07fffff] PMD -> [ffff813820200000-ffff81383c1fffff] on node 7
instead of a very long print out...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
typical case: four sockets system, every node has 4g ram, and we are using:
memmap=10g$4g
to mask out memory on node1 and node2
when numa is enabled, early_node_mem is used to get node_data and node_bootmap.
if it can not get memory from the same node with find_e820_area(), it will
use alloc_bootmem to get buff from previous nodes.
so check it and print out some info about it.
need to move early_res_to_bootmem into every setup_node_bootmem.
and it takes range that node has. otherwise alloc_bootmem could return addr
that reserved early.
depends on "mm: make reserve_bootmem can crossed the nodes".
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"mm: make reserve_bootmem can crossed the nodes" provides new
reserve_bootmem(), let reserve_bootmem_generic() use that.
reserve_bootmem_generic() is used to reserve initramdisk, so this way
we can make sure even when bootloader or kexec load ranges cross the
node memory boundaries, reserve_bootmem still works.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
disable /dev/mem mmap of RAM with PAT. It makes things safer and
eliminates aliasing. A future improvement would be to avoid the
range_is_allowed duplication.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-fixes:
x86 PAT: decouple from nonpromisc devmem
x86 PAT: tone down debugging messages
It is claimed that NexGen CPUs were never shipped:
http://lkml.org/lkml/2008/4/20/179
Also, the kernel support for these chips has been broken for
a long time, the code intended to support NexGen thereby being
essentially dead.
As an outcome of the discussion that can be found using the URL
above, this patch removes the NexGen support altogether.
The changes in this patch survived a defconfig build for i386, a
couple of successful randconfig builds, as well as a runtime test,
which consisted in booting a 32-bit x86 box up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus reported these excessive debug printouts:
> Overlap at 0xe0300000-0xe0400000
> Overlap at 0xe0300000-0xe0380000
> Overlap at 0xe0300000-0xe0400000
> Overlap at 0xe0300000-0xe0400000
> Overlap at 0xe0300000-0xe0400000
> Overlap at 0xe0300000-0xe0400000
> Overlap at 0xe0300000-0xe0400000
turn that into a pr_debug().
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-pat:
generic: add ioremap_wc() interface wrapper
/dev/mem: make promisc the default
pat: cleanups
x86: PAT use reserve free memtype in mmap of /dev/mem
x86: PAT phys_mem_access_prot_allowed for dev/mem mmap
x86: PAT avoid aliasing in /dev/mem read/write
devmem: add range_is_allowed() check to mmap of /dev/mem
x86: introduce /dev/mem restrictions with a config option
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-xen-next: (52 commits)
xen: add balloon driver
xen: allow compilation with non-flat memory
xen: fold xen_sysexit into xen_iret
xen: allow set_pte_at on init_mm to be lockless
xen: disable preemption during tlb flush
xen pvfb: Para-virtual framebuffer, keyboard and pointer driver
xen: Add compatibility aliases for frontend drivers
xen: Module autoprobing support for frontend drivers
xen blkfront: Delay wait for block devices until after the disk is added
xen/blkfront: use bdget_disk
xen: Make xen-blkfront write its protocol ABI to xenstore
xen: import arch generic part of xencomm
xen: make grant table arch portable
xen: replace callers of alloc_vm_area()/free_vm_area() with xen_ prefixed one
xen: make include/xen/page.h portable moving those definitions under asm dir
xen: add resend_irq_on_evtchn() definition into events.c
Xen: make events.c portable for ia64/xen support
xen: move events.c to drivers/xen for IA64/Xen support
xen: move features.c from arch/x86/xen/features.c to drivers/xen
xen: add missing definitions in include/xen/interface/vcpu.h which ia64/xen needs
...
All pagetables need fundamentally the same setup and destruction, so
just use the same code for everything.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make KERNEL_PGD_PTRS common, as previously it was only being defined
for 32-bit.
There are a couple of follow-on changes from this:
- KERNEL_PGD_PTRS was being defined in terms of USER_PGD_PTRS. The
definition of USER_PGD_PTRS doesn't really make much sense on x86-64,
since it can have two different user address-space configurations.
I renamed USER_PGD_PTRS to KERNEL_PGD_BOUNDARY, which is meaningful
for all of 32/32, 32/64 and 64/64 process configurations.
- USER_PTRS_PER_PGD was also defined and was being used for similar
purposes. Converting its users to KERNEL_PGD_BOUNDARY left it
completely unused, and so I removed it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Zach Amsden <zach@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename (alloc|release)_(pt|pd) to pte/pmd to explicitly match the name
of the appropriate pagetable level structure.
[ x86.git merge work by Mark McLoughlin <markmc@redhat.com> ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Common definitions for 3-level pagetable functions.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Common definitions for 2-level pagetable functions.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a common arch/x86/mm/pgtable.c file for common pagetable functions.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert asm-x86/pgalloc_64.h from macros into functions (#include hell
prevents __*_free_tlb from being inline, but they're probably a bit
big to inline anyway).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use reserve_memtype and free_memtype wrappers for /dev/mem mmaps. The memtype
is slightly complicated here, given that we have to support existing X mappings.
We fallback on UC_MINUS for that.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce phys_mem_access_prot_allowed(), which checks whether the mapping
is possible, without any conflicts and returns success or failure based on that.
phys_mem_access_prot() by itself does not allow failure case. This ability
to return error is needed for PAT where we may have aliasing conflicts.
x86 setup __HAVE_PHYS_MEM_ACCESS_PROT and move x86 specific code out of
/dev/mem into arch specific area.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add xlate and unxlate around /dev/mem read/write. This sets up the mapping
that can be used for /dev/mem read and write without aliasing worries.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch introduces a restriction on /dev/mem: Only non-memory can be
read or written unless the newly introduced config option is set.
The X server needs access to /dev/mem for the PCI space, but it doesn't need
access to memory; both the file permissions and SELinux permissions of /dev/mem
just make X effectively super-super powerful. With the exception of the
BIOS area, there's just no valid app that uses /dev/mem on actual memory.
Other popular users of /dev/mem are rootkits and the like.
(note: mmap access of memory via /dev/mem was already not allowed since
a really long time)
People who want to use /dev/mem for kernel debugging can enable the config
option.
The restrictions of this patch have been in the Fedora and RHEL kernels for
at least 4 years without any problems.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel: (62 commits)
sched: build fix
sched: better rt-group documentation
sched: features fix
sched: /debug/sched_features
sched: add SCHED_FEAT_DEADLINE
sched: debug: show a weight tree
sched: fair: weight calculations
sched: fair-group: de-couple load-balancing from the rb-trees
sched: fair-group scheduling vs latency
sched: rt-group: optimize dequeue_rt_stack
sched: debug: add some debug code to handle the full hierarchy
sched: fair-group: SMP-nice for group scheduling
sched, cpuset: customize sched domains, core
sched, cpuset: customize sched domains, docs
sched: prepatory code movement
sched: rt: multi level group constraints
sched: task_group hierarchy
sched: fix the task_group hierarchy for UID grouping
sched: allow the group scheduler to have multiple levels
sched: mix tasks and groups
...
* Move large array "struct bootnode nodes" from stack to _initdata
section to reduce amount of stack space required.
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move dma_ops structure definition to pci-dma.c, where it
belongs.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For example, If the physical address layout on a two node system with 8 GB
memory is something like:
node 0: 0-2GB, 4-6GB
node 1: 2-4GB, 6-8GB
Current kernels fail to boot/detect this NUMA topology.
ACPI SRAT tables can expose such a topology which needs to be supported.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
this function doesnt just 'find' the max_pfn - it also has
other side-effects such as registering sparse memory maps.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix printk formats in x86/mm/ioremap.c:
next-20080410/arch/x86/mm/ioremap.c:137: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'resource_size_t'
next-20080410/arch/x86/mm/ioremap.c:188: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'resource_size_t'
next-20080410/arch/x86/mm/ioremap.c:188: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'long unsigned int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
