Put it one page below the top of the 32-bit address space.
This gives us ~16MB more address space to work with.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently allocations are very constrained for 32-bit processes.
It grows down-up from 0x70000000 to 0xf0000000 which gives about
2GB of stack + dynamic mmap() space.
So support the top-down method, and we need to override the
generic helper function in order to deal with D-cache coloring.
With these changes I was able to squeeze out a mmap() just over
3.6GB in size in a 32-bit process.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is good for up to %50 performance improvement of some test cases.
The problem has been the race conditions, and hopefully I've plugged
them all up here.
1) There was a serious race in switch_mm() wrt. lazy TLB
switching to and from kernel threads.
We could erroneously skip a tsb_context_switch() and thus
use a stale TSB across a TSB grow event.
There is a big comment now in that function describing
exactly how it can happen.
2) All code paths that do something with the TSB need to be
guarded with the mm->context.lock spinlock. This makes
page table flushing paths properly synchronize with both
TSB growing and TLB context changes.
3) TSB growing events are moved to the end of successful fault
processing. Previously it was in update_mmu_cache() but
that is deadlock prone. At the end of do_sparc64_fault()
we hold no spinlocks that could deadlock the TSB grow
sequence. We also have dropped the address space semaphore.
While we're here, add prefetching to the copy_tsb() routine
and put it in assembler into the tsb.S file. This piece of
code is quite time critical.
There are some small negative side effects to this code which
can be improved upon. In particular we grab the mm->context.lock
even for the tsb insert done by update_mmu_cache() now and that's
a bit excessive. We can get rid of that locking, and the same
lock taking in flush_tsb_user(), by disabling PSTATE_IE around
the whole operation including the capturing of the tsb pointer
and tsb_nentries value. That would work because anyone growing
the TSB won't free up the old TSB until all cpus respond to the
TSB change cross call.
I'm not quite so confident in that optimization to put it in
right now, but eventually we might be able to and the description
is here for reference.
This code seems very solid now. It passes several parallel GCC
bootstrap builds, and our favorite "nut cruncher" stress test which is
a full "make -j8192" build of a "make allmodconfig" kernel. That puts
about 256 processes on each cpu's run queue, makes lots of process cpu
migrations occur, causes lots of page table and TLB flushing activity,
incurs many context version number changes, and it swaps the machine
real far out to disk even though there is 16GB of ram on this test
system. :-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Report 'sun4v' when appropriate in /proc/cpuinfo
Remove all the verifications of the OBP version string. Just
make sure it's there, and report it raw in the bootup logs and
via /proc/cpuinfo.
Signed-off-by: David S. Miller <davem@davemloft.net>
The mapping is a simple "(cpuid >> 2) == core" for now.
Later we'll add more sophisticated code that will walk
the sun4v machine description and figure this out from
there.
We should also add core mappings for jaguar and panther
processors.
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been pending for a long time, and the fact
that we waste a ton of ram on some configurations
kind of pushed things over the edge.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't piggy back the SMP receive signal code to do the
context version change handling.
Instead allocate another fixed PIL number for this
asynchronous cross-call. We can't use smp_call_function()
because this thing is invoked with interrupts disabled
and a few spinlocks held.
Also, fix smp_call_function_mask() to count "cpus" correctly.
There is no guarentee that the local cpu is in the mask
yet that is exactly what this code was assuming.
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch converts arch/sparc64 to kzalloc usage.
Crosscompile tested with allyesconfig.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't try to avoid putting non-base page sized entries
into the user TSB. It actually costs us more to check
this than it helps.
Eventually we'll have a multiple TSB scheme for user
processes. Once a process starts using larger pages,
we'll allocate and use such a TSB.
Signed-off-by: David S. Miller <davem@davemloft.net>
This cpu mondo sending interface isn't all that easy to
use correctly...
We were clearing out the wrong bits from the "mask" after getting
something other than EOK from the hypervisor.
It turns out the hypervisor can just be resent the same cpu_list[]
array, with the 0xffff "done" entries still in there, and it will do
the right thing.
So don't update or try to rebuild the cpu_list[] array to condense it.
This requires the "forward_progress" check to be done slightly
differently, but this new scheme is less bug prone than what we were
doing before.
Signed-off-by: David S. Miller <davem@davemloft.net>
We were clobbering a base register before we were done
using it. Fix a comment typo while we're here.
Signed-off-by: David S. Miller <davem@davemloft.net>
The UltraSPARC T1 manual recommends this because the chip
could instruction prefetch into the VA hole, and this would
also make decoding certain kinds of memory access traps
more difficult (because the chip sign extends certain pieces
of trap state).
Signed-off-by: David S. Miller <davem@davemloft.net>
First of all, use the known _PAGE_EXEC_{4U,4V} value instead
of loading _PAGE_EXEC from memory. We either know which one
to use by context, or we can code patch the test.
Next, we need to check executability of a PTE in the generic
TSB miss handler.
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several bugs in the SUN4V cpu mondo dispatch code.
In fact, if we ever got a EWOULDBLOCK or other error from
the hypervisor call, we'd potentially send a cpu mondo multiple
times to the same cpu and even worse we could loop until the
timeout resending the same mondo over and over to such cpus.
So let's bulletproof this thing as follows:
1) Implement cpu_mondo_send() and cpu_state() hypervisor calls
in arch/sparc64/kernel/entry.S, add prototypes to asm/hypervisor.h
2) Don't build and update the cpulist using inline functions, this
was causing the cpu mask to not get updated in the caller.
3) Disable interrupts during the entire mondo send, otherwise our
cpu list and/or mondo block could get overwritten if we take
an interrupt and do a cpu mondo send on the current cpu.
4) Check for all possible error return types from the cpu_mondo_send()
hypervisor call. In particular:
HV_EOK) Our work is done, all cpus have received the mondo.
HV_CPUERROR) One or more of the cpus in the cpu list we passed
to the hypervisor are in error state. Use cpu_state()
calls over the entries in the cpu list to see which
ones. Record them in "error_mask" and report this
after we are done sending the mondo to cpus which are
not in error state.
HV_EWOULDBLOCK) We need to keep trying.
Any other error we consider fatal, we report the event and exit
immediately.
5) We only timeout if forward progress is not made. Forward progress
is defined as having at least one cpu get the mondo successfully
in a given cpu_mondo_send() call. Otherwise we bump a counter
and delay a little. If the counter hits a limit, we signal an
error and report the event.
Also, smp_call_function_mask() error handling reports the number
of cpus incorrectly.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) We must flush the TLB, duh.
2) Even if the sw context was seen to be valid, the local cpu's
hw context can be out of date, so reload it unconditionally.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check TLB flush hypervisor calls for errors and report them.
Pass HV_MMU_ALL always for now, we can add back the optimization
to avoid the I-TLB flush later.
Always explicitly page align the virtual address arguments.
Signed-off-by: David S. Miller <davem@davemloft.net>
The context allocation scheme we use depends upon there being a 1<-->1
mapping from cpu to physical TLB for correctness. Chips like Niagara
break this assumption.
So what we do is notify all cpus with a cross call when the context
version number changes, and if necessary this makes them allocate
a valid context for the address space they are running at the time.
Stress tested with make -j1024, make -j2048, and make -j4096 kernel
builds on a 32-strand, 8 core, T2000 with 16GB of ram.
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise with too much stuff enabled in the kernel config
we can end up with an unaligned trap table.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we take a window fault, on SUN4V set %gl to zero before we
turn PSTATE_IE back on in %pstate. Otherwise if we take an
interrupt we'll end up with corrupt register state.
Signed-off-by: David S. Miller <davem@davemloft.net>
It can map all of the linear kernel mappings with zero TSB hash
conflicts for systems with 16GB or less ram. In such cases, on
SUN4V, once we load up this TSB the first time with all the
mappings, we never take a linear kernel mapping TLB miss ever
again, the hypervisor handles them all.
Signed-off-by: David S. Miller <davem@davemloft.net>
We use a bitmap, one bit for every 256MB of memory. If the
bit is set we can use a 256MB PTE for linear mappings, else
we have to use a 4MB PTE.
SUN4V support is there, and we can very easily add support
for Panther cpu 256MB PTEs in the future.
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to turn off the "polling nrflag" bit when we sleep
the cpu like this, so that we'll get a cross-cpu interrupt
to wake the processor up from the yield.
We also have to disable PSTATE_IE in %pstate around the yield
call and recheck need_resched() in order to avoid any races.
Signed-off-by: David S. Miller <davem@davemloft.net>
Set, but never used.
We used to use this for dynamic IRQ retargetting, but that
code died a long time ago.
Signed-off-by: David S. Miller <davem@davemloft.net>
It's extremely noisy and causes much grief on slow
consoles with large numbers of cpus.
We'll have to provide this some saner way in order
to re-enable this.
Signed-off-by: David S. Miller <davem@davemloft.net>
We're about to seriously die in these cases so it is important
that the messages make it to the console.
Signed-off-by: David S. Miller <davem@davemloft.net>
Another case where we have to force ourselves into global register
level one. Also make sure the arguments passed to sun4v_do_mna() are
correct.
This area actually needs some more work, for example spill fixup is
not necessarily going to do the right thing for this case.
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like kvmap_dtlb_longpath we have to force the
global register level to one in order to mimick the
PSTATE_MG --> PSTATE_AG trasition done on SUN4U.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SUN4V convention with non-shared TSBs is that the context
bit of the TAG is clear. So we have to choose an "invalid"
bit and initialize new TSBs appropriately. Otherwise a zero
TAG looks "valid".
Make sure, for the window fixup cases, that we use the right
global registers and that we don't potentially trample on
the live global registers in etrap/rtrap handling (%g2 and
%g6) and that we put the missing virtual address properly
in %g5.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Add error return checking for TLB load hypervisor
calls.
2) Don't fallthru to dtlb tsb miss handler from itlb tsb
miss handler, oops.
3) On window fixups, propagate fault information to fixup
handler correctly.
Signed-off-by: David S. Miller <davem@davemloft.net>
This gives more consistent bogomips and delay() semantics,
especially on sun4v. It gives weird looking values though...
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to use the real hardware processor ID when
targetting interrupts, not the "define to 0" thing
the uniprocessor build gives us.
Also, fill in the Node-ID and Agent-ID fields properly
on sun4u/Safari.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the top-level cnode had multi entries in it's "reg"
property, we'd fail. The buffer wasn't large enough in
such cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sibling cpu bringup is extremely fragile. We can only
perform the most basic calls until we take over the trap
table from the firmware/hypervisor on the new cpu.
This means no accesses to %g4, %g5, %g6 since those can't be
TLB translated without our trap handlers.
In order to achieve this:
1) Change sun4v_init_mondo_queues() so that it can operate in
several modes.
It can allocate the queues, or install them in the current
processor, or both.
The boot cpu does both in it's call early on.
Later, the boot cpu allocates the sibling cpu queue, starts
the sibling cpu, then the sibling cpu loads them in.
2) init_cur_cpu_trap() is changed to take the current_thread_info()
as an argument instead of reading %g6 directly on the current
cpu.
3) Create a trampoline stack for the sibling cpus. We do our basic
kernel calls using this stack, which is locked into the kernel
image, then go to our proper thread stack after taking over the
trap table.
4) While we are in this delicate startup state, we put 0xdeadbeef
into %g4/%g5/%g6 in order to catch accidental accesses.
5) On the final prom_set_trap_table*() call, we put &init_thread_union
into %g6. This is a hack to make prom_world(0) work. All that
wants to do is restore the %asi register using
get_thread_current_ds().
Longer term we should just do the OBP calls to set the trap table by
hand just like we do for everything else. This would avoid that silly
prom_world(0) issue, then we can remove the init_thread_union hack.
Signed-off-by: David S. Miller <davem@davemloft.net>
For 32 cpus and a slow console, it just wedges the
machine especially with DETECT_SOFTLOCKUP enabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole algorithm was wrong. What we need to do is:
1) Walk each PCI bus above this device on the path to the
PCI controller nexus, and for each:
a) If interrupt-map exists, apply it, record IRQ controller node
b) Else, swivel interrupt number using PCI_SLOT(), use PCI bus
parent OBP node as controller node
c) Walk up to "controller node" until we hit the first PCI bus
in this domain, or "controller node" is the PCI controller
OBP node
2) If we walked to PCI controller OBP node, we're done.
3) Else, apply PCI controller interrupt-map to interrupt.
There is some stuff that needs to be checked out for ebus and
isa, but the PCI part is good to go.
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to set the global register set _AND_ disable
PSTATE_IE in %pstate. The original patch sequence was
leaving PSTATE_IE enabled when returning to kernel mode,
oops.
This fixes the random register corruption being seen
on SUN4V.
Signed-off-by: David S. Miller <davem@davemloft.net>
Forgot to multiply by 8 * 1024, oops. Correct the size constant when
the virtual-dma arena is 2GB in size, it should bet 256 not 128.
Finally, log some info about the TSB at probe time.
Signed-off-by: David S. Miller <davem@davemloft.net>
For SUN4V, we were clobbering %o5 to do the hypervisor call.
This clobbers the saved %pstate value and we end up writing
garbage into that register as a result. Oops.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use prom_startcpu_cpuid() on SUN4V instead of prom_startcpu().
We should really test for "SUNW,start-cpu-by-cpuid" presence
and use it if present even on SUN4U.
Signed-off-by: David S. Miller <davem@davemloft.net>
When crawling up the PCI bus chain, stop at the first node
that has an interrupt-map property before we hit the root.
Also, if we use a bus interrupt-{map,mask} do not forget to
update the 'intmask' pointer as we do for the 'intmap' pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
On SUN4V, force IRQ state to idle in enable_irq(). However,
I'm still not sure this is %100 correct.
Call add_interrupt_randomness() on SUN4V too.
Signed-off-by: David S. Miller <davem@davemloft.net>
On the PBM's first bus number, only allow device 0, function 0, to be
poked at with PCI config space accesses.
For some reason, this single device responds to all device numbers.
Also, reduce the verbiage of the debugging log printk's for PCI cfg
space accesses in the SUN4V PCI controller driver, so that it doesn't
overwhelm the slow SUN4V hypervisor console.
Signed-off-by: David S. Miller <davem@davemloft.net>
We should dynamically allocate the per-cpu pglist not use
an in-kernel-image datum, since __pa() does not work on
such addresses.
Also, consistently use "u32" for devhandle.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add udelay to polling console write loop, and increment
the loop limit.
Name the device "ttyHV" and pass that to add_preferred_console()
when we're using hypervisor console.
Kill sunhv_console_setup(), it's empty.
Handle the case where we don't want to use hypervisor console.
(ie. we have a head attached to a sun4v machine)
Signed-off-by: David S. Miller <davem@davemloft.net>
Get bus range from child of PCI controller root nexus.
This is actually a hack, but the PCI-E bridge sitting
at the top of the PCI tree responds to PCI config cycles
for every device number, so best to just ignore it for now.
Preliminary PCI irq routing, needs lots of work.
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear top 8-bits of physical addresses in "ranges" property.
This gives the actual physical address.
Detect PBM-A vs. PBM-B by checking bit 0x40 of the devhandle.
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI cfg space is accessed transparently through the Hypervisor and not
through direct cpu PIO operations.
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to use bootmem during init_IRQ and page alloc
for sibling cpu calls.
Also, fix incorrect hypervisor call return value
checks in the hypervisor SMP cpu mondo send code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Yes, you heard it right, they changed the PTE layout for
SUN4V. Ho hum...
This is the simple and inefficient way to support this.
It'll get optimized, don't worry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Code patching did not sign extend negative branch
offsets correctly.
Kernel TLB miss path needs patching and %g4 register
preservation in order to handle SUN4V correctly.
Signed-off-by: David S. Miller <davem@davemloft.net>
prom_sun4v_name should be "sun4v" not "SUNW,sun4v"
Also, this is too early to make use of the
.sun4v_Xinsn_patch code patching, so just check
things manually.
This gets us at least to prom_init() on Niagara.
Signed-off-by: David S. Miller <davem@davemloft.net>
There was also a bug in sun4v_itlb_miss, it loaded the
MMU Fault Status base into %g3 instead of %g2.
This pointed out a fast path for TSB miss processing,
since we have %g2 with the MMU Fault Status base, we
can use that to quickly load up the PGD phys address.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is where the virtual address of the fault status
area belongs.
To set it up we don't make a hypervisor call, instead
we call OBP's SUNW,set-trap-table with the real address
of the fault status area as the second argument. And
right before that call we write the virtual address into
ASI_SCRATCHPAD vaddr 0x0.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add assembler file for PCI hypervisor calls.
Setup basic skeleton of SUN4V PCI controller driver.
Add 32-bit devhandle to PBM struct, as this is needed for
hypervisor calls.
Signed-off-by: David S. Miller <davem@davemloft.net>
Abstract out IOMMU operations so that we can have a different
set of calls on sun4v, which needs to do things through
hypervisor calls.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we register a TSB with the hypervisor, so that it or hardware can
handle TLB misses and do the TSB walk for us, the hypervisor traps
down to these trap when it incurs a TSB miss.
Processing is simple, we load the missing virtual address and context,
and do a full page table walk.
Signed-off-by: David S. Miller <davem@davemloft.net>
We look for "SUNW,sun4v" in the 'compatible' property
of the root OBP device tree node.
Protect every %ver register access, to make sure it is
not touched on sun4v, as %ver is hyperprivileged there.
Lock kernel TLB entries using hypervisor calls instead of
calls into OBP.
Signed-off-by: David S. Miller <davem@davemloft.net>
Technically the hypervisor call supports sending in a list
of all cpus to get the cross-call, but I only pass in one
cpu at a time for now.
The multi-cpu support is there, just ifdef'd out so it's easy to
enable or delete it later.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sun4v has 4 interrupt queues: cpu, device, resumable errors,
and non-resumable errors. A set of head/tail offset pointers
help maintain a work queue in physical memory. The entries
are 64-bytes in size.
Each queue is allocated then registered with the hypervisor
as we bring cpus up.
The two error queues each get a kernel side buffer that we
use to quickly empty the main interrupt queue before we
call up to C code to log the event and possibly take evasive
action.
Signed-off-by: David S. Miller <davem@davemloft.net>
Happily we have no D-cache aliasing issues on these
chips, so the implementation is very straightforward.
Add a stub in bootup which will be where the patching
calls will be made for niagara/sun4v/hypervisor.
Signed-off-by: David S. Miller <davem@davemloft.net>
Things are a little tricky because, unlike sun4u, we have
to:
1) do a hypervisor trap to do the TLB load.
2) do the TSB lookup calculations by hand
Signed-off-by: David S. Miller <davem@davemloft.net>
If we're just switching between different alternate global
sets, nop it out on sun4v. Also, get rid of all of the
alternate global save/restore in the OBP CIF trampoline code.
Signed-off-by: David S. Miller <davem@davemloft.net>
They are totally unnecessary because:
1) Interrupts are already disabled when switch_to()
runs.
2) We don't use hard-coded alternate globals any longer.
This found a case in rtrap, which still assumed alternate
global %g6 was current_thread_info(), and that is fixed
by this changeset as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
As we save trap state onto the stack, the store buffer fills up
mid-way through and we stall for several cycles as the store buffer
trickles out to the L2 cache. Meanwhile we can do some privileged
register reads and other calculations, essentially for free.
Signed-off-by: David S. Miller <davem@davemloft.net>
And more consistently check cheetah{,_plus} instead
of assuming anything not spitfire is cheetah{,_plus}.
Signed-off-by: David S. Miller <davem@davemloft.net>
When saving and restoing trap state, do the window spill/fill
handling inline so that we never trap deeper than 2 trap levels.
This is important for chips like Niagara.
The window fixup code is massively simplified, and many more
improvements are now possible.
Signed-off-by: David S. Miller <davem@davemloft.net>
On uniprocessor, it's always zero for optimize that.
On SMP, the jmpl to the stub kills the return address stack in the cpu
branch prediction logic, so expand the code sequence inline and use a
code patching section to fix things up. This also always better and
explicit register selection, which will be taken advantage of in a
future changeset.
The hard_smp_processor_id() function is big, so do not inline it.
Fix up tests for Jalapeno to also test for Serrano chips too. These
tests want "jbus Ultra-IIIi" cases to match, so that is what we should
test for.
Signed-off-by: David S. Miller <davem@davemloft.net>
The are distrupting, which by the sparc v9 definition means they
can only occur when interrupts are enabled in the %pstate register.
This never occurs in any of the trap handling code running at
trap levels > 0.
So just mark it as an unexpected trap.
This allows us to kill off the cee_stuff member of struct thread_info.
Signed-off-by: David S. Miller <davem@davemloft.net>
This way we don't need to lock the TSB into the TLB.
The trick is that every TSB load/store is registered into
a special instruction patch section. The default uses
virtual addresses, and the patch instructions use physical
address load/stores.
We can't do this on all chips because only cheetah+ and later
have the physical variant of the atomic quad load.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are returning back to kernel mode, %g4 could be live
(for example, in the case where we window spill in the etrap
code). So do not change it's value if going back to kernel.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we use %g5 itself as a temporary, it can get clobbered
if we take an interrupt mid-stream and thus cause end up with
the final %g5 value too early as a result of rtrap processing.
Set %g5 at the very end, atomically, to avoid this problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
%g6 is not necessarily set to current_thread_info()
at sparc64_realfault_common. So store the fault
code and address after we invoke etrap and %g6 is
properly set up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Just flip the bit off of whatever it's currently set to.
PSTATE_IE is guarenteed to be enabled when we get here.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is totally unnecessary complexity. After we take over
the trap table, we handle all PROM tlb misses fully.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the trap code was still assuming that alternate
global %g6 was hard coded with current_thread_info().
Let's just consistently flush at KERNBASE when we need
a pipeline synchronization. That's locked into the TLB
and will always work.
Signed-off-by: David S. Miller <davem@davemloft.net>
As the RSS grows, grow the TSB in order to reduce the likelyhood
of hash collisions and thus poor hit rates in the TSB.
This definitely needs some serious tuning.
Signed-off-by: David S. Miller <davem@davemloft.net>
This also cleans up tsb_context_switch(). The assembler
routine is now __tsb_context_switch() and the former is
an inline function that picks out the bits from the mm_struct
and passes it into the assembler code as arguments.
setup_tsb_parms() computes the locked TLB entry to map the
TSB. Later when we support using the physical address quad
load instructions of Cheetah+ and later, we'll simply use
the physical address for the TSB register value and set
the map virtual and PTE both to zero.
Signed-off-by: David S. Miller <davem@davemloft.net>
Move {init_new,destroy}_context() out of line.
Do not put huge pages into the TSB, only base page size translations.
There are some clever things we could do here, but for now let's be
correct instead of fancy.
Signed-off-by: David S. Miller <davem@davemloft.net>
UltraSPARC has special sets of global registers which are switched to
for certain trap types. There is one set for MMU related traps, one
set of Interrupt Vector processing, and another set (called the
Alternate globals) for all other trap types.
For what seems like forever we've hard coded the values in some of
these trap registers. Some examples include:
1) Interrupt Vector global %g6 holds current processors interrupt
work struct where received interrupts are managed for IRQ handler
dispatch.
2) MMU global %g7 holds the base of the page tables of the currently
active address space.
3) Alternate global %g6 held the current_thread_info() value.
Such hardcoding has resulted in some serious issues in many areas.
There are some code sequences where having another register available
would help clean up the implementation. Taking traps such as
cross-calls from the OBP firmware requires some trick code sequences
wherein we have to save away and restore all of the special sets of
global registers when we enter/exit OBP.
We were also using the IMMU TSB register on SMP to hold the per-cpu
area base address, which doesn't work any longer now that we actually
use the TSB facility of the cpu.
The implementation is pretty straight forward. One tricky bit is
getting the current processor ID as that is different on different cpu
variants. We use a stub with a fancy calling convention which we
patch at boot time. The calling convention is that the stub is
branched to and the (PC - 4) to return to is in register %g1. The cpu
number is left in %g6. This stub can be invoked by using the
__GET_CPUID macro.
We use an array of per-cpu trap state to store the current thread and
physical address of the current address space's page tables. The
TRAP_LOAD_THREAD_REG loads %g6 with the current thread from this
table, it uses __GET_CPUID and also clobbers %g1.
TRAP_LOAD_IRQ_WORK is used by the interrupt vector processing to load
the current processor's IRQ software state into %g6. It also uses
__GET_CPUID and clobbers %g1.
Finally, TRAP_LOAD_PGD_PHYS loads the physical address base of the
current address space's page tables into %g7, it clobbers %g1 and uses
__GET_CPUID.
Many refinements are possible, as well as some tuning, with this stuff
in place.
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking a nod from the powerpc port.
With the per-cpu caching of both the page allocator and SLAB, the
pgtable quicklist scheme becomes relatively silly and primitive.
Signed-off-by: David S. Miller <davem@davemloft.net>
We now use the TSB hardware assist features of the UltraSPARC
MMUs.
SMP is currently knowingly broken, we need to find another place
to store the per-cpu base pointers. We hid them away in the TSB
base register, and that obviously will not work any more :-)
Another known broken case is non-8KB base page size.
Also noticed that flush_tlb_all() is not referenced anywhere, only
the internal __flush_tlb_all() (local cpu only) is used by the
sparc64 port, so we can get rid of flush_tlb_all().
The kernel gets it's own 8KB TSB (swapper_tsb) and each address space
gets it's own private 8K TSB. Later we can add code to dynamically
increase the size of per-process TSB as the RSS grows. An 8KB TSB is
good enough for up to about a 4MB RSS, after which the TSB starts to
incur many capacity and conflict misses.
We even accumulate OBP translations into the kernel TSB.
Another area for refinement is large page size support. We could use
a secondary address space TSB to handle those.
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch "[SPARC64]: Get rid of fast IRQ feature"
moved the the code from arch/sparc64/kernel/entry.S:
lduba [%g7] ASI_PHYS_BYPASS_EC_E, %g5
or %g5, AUXIO_AUX1_FTCNT, %g5
stba %g5, [%g7] ASI_PHYS_BYPASS_EC_E
andn %g5, AUXIO_AUX1_FTCNT, %g5
stba %g5, [%g7] ASI_PHYS_BYPASS_EC_E
to arch/sparc64/kernel/irq.c:
val = readb(auxio_register);
val |= AUXIO_AUX1_FTCNT;
writeb(val, auxio_register);
val &= AUXIO_AUX1_FTCNT;
writeb(val, auxio_register);
This looks like it it missing a bitwise not, which is reintroduced
by this patch.
Due to lack of a floppy device, I could not test it, but it looks
evident.
Signed-off-by: Bernhard R Link <brlink@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must use the "a" (allocate) attribute every time we
emit an entry into the __ex_table section.
For consistency, use "a" instead of #alloc which is some
Solaris compat cruft GNU as provides on Sparc.
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to kernel/sched.c's init code to use for_each_cpu()
requires that the cpu_possible_map be setup much earlier.
Set it up via setup_arch(), constrained to NR_CPUS, and later
constrain it to max_cpus in smp_prepare_cpus().
This fixes SMP booting on sparc64.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sparc64 64 bit syscall table seems to be broken as it has
compat_sys_newfstatat in its syscall table instead of sys_newfstatat.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, the Solaris syscall table is sized differrently,
and does not go beyond entry 255, so trim off the excess
entries.
Signed-off-by: David S. Miller <davem@davemloft.net>
This also includes by necessity _TIF_RESTORE_SIGMASK support,
which actually resulted in a lot of cleanups.
The sparc signal handling code is quite a mess and I should
clean it up some day.
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is a series of patches which introduce in total 13 new system calls
which take a file descriptor/filename pair instead of a single file
name. These functions, openat etc, have been discussed on numerous
occasions. They are needed to implement race-free filesystem traversal,
they are necessary to implement a virtual per-thread current working
directory (think multi-threaded backup software), etc.
We have in glibc today implementations of the interfaces which use the
/proc/self/fd magic. But this code is rather expensive. Here are some
results (similar to what Jim Meyering posted before).
The test creates a deep directory hierarchy on a tmpfs filesystem. Then
rm -fr is used to remove all directories. Without syscall support I get
this:
real 0m31.921s
user 0m0.688s
sys 0m31.234s
With syscall support the results are much better:
real 0m20.699s
user 0m0.536s
sys 0m20.149s
The interfaces are for obvious reasons currently not much used. But they'll
be used. coreutils (and Jeff's posixutils) are already using them.
Furthermore, code like ftw/fts in libc (maybe even glob) will also start using
them. I expect a patch to make follow soon. Every program which is walking
the filesystem tree will benefit.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@ftp.linux.org.uk>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Eddie C. Dost <ecd@brainaid.de>
I have the following patch for serial console over the RSC
(remote system controller) on my E250 machine. It basically adds
support for input-device=rsc and output-device=rsc from OBP, and
allows 115200,8,n,1,- serial mode setting.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure a consistent value is read from the STICK register by ensuring
that both high and low are read without high changing due to a roll
over of the low register.
Various Debian/SPARC users (myself include) have noticed problems with
Hummingbird based systems. The symptoms are that the system time is
seen to jump forward 3 days, 6 hours, 11 minutes give or take a few
seconds. In many cases the system then hangs some time afterwards.
I've spotted a race condition in the code to read the STICK register.
I could not work out why 3d, 6h, 11m is important but guess that it is
due to the 2^32 jump of STICK (forwards on one read and then the next
read will seem to be backwards) during a timer interrupt. I'm guessing
that a change of -2^32 will get converted to a large unsigned
increment after the arithmetic manipulation between STICK,
nanoseconds, jiffies etc.
I did a test where I modified __hbird_read_stick to artificially
inject rollover faults forcefully every few seconds. With this I saw
the clock jump over 6 times in 12 hours compared to once every month
or so.
Signed-off-by: Richard Mortimer <richm@oldelvet.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
arch: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a window where a probe gets removed right after the probe is hit
on some different cpu. In this case probe handlers can't find a matching
probe instance related to break address. In this case we need to read the
original instruction at break address to see if that is not a break/int3
instruction and recover safely.
Previous code had a bug where we were not checking for the above race in
case of reentrant probes and the below patch fixes this race.
Tested on IA64, Powerpc, x86_64.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently arch_remove_kprobes() is only implemented/required for x86_64 and
powerpc. All other architecture like IA64, i386 and sparc64 implementes a
dummy function which is being called from arch independent kprobes.c file.
This patch removes the dummy functions and replaces it with
#define arch_remove_kprobe(p, s) do { } while(0)
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since Kprobes runtime exception handlers is now lock free as this code path is
now using RCU to walk through the list, there is no need for the
register/unregister{_kprobe} to use spin_{lock/unlock}_isr{save/restore}. The
serialization during registration/unregistration is now possible using just a
mutex.
In the above process, this patch also fixes a minor memory leak for x86_64 and
powerpc.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that all these entries in the arch ioctl32.c files are gone [1], we can
build fs/compat_ioctl.c as a normal object and kill tons of cruft. We need a
special do_ioctl32_pointer handler for s390 so the compat_ptr call is done.
This is not needed but harmless on all other architectures. Also remove some
superflous includes in fs/compat_ioctl.c
Tested on ppc64.
[1] parisc still had it's PPP handler left, which is not fully correct
for ppp and besides that ppp uses the generic SIOCPRIV ioctl so it'd
kick in for all netdevice users. We can introduce a proper handler
in one of the next patch series by adding a compat_ioctl method to
struct net_device but for now let's just kill it - parisc doesn't
compile in mainline anyway and I don't want this to block this
patchset.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment in compat.c is wrong, every architecture provides a
get_compat_sigevent() for the IPC compat code already.
This basically moves the x86_64 version to common code and removes all the
others.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Adrian Bunk <bunk@stusta.de>
- create one common dump_thread() prototype in kernel.h
- dump_thread() is only used in fs/binfmt_aout.c and can therefore be
removed on all architectures where CONFIG_BINFMT_AOUT is not
available
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't clobber register %l0 while checking TI_SYS_NOERROR value in
syscall return path. This bug was introduced by:
db7d9a4eb7
Problem narrowed down by Luis F. Ortiz and Richard Mortimer.
I tried using %l2 as suggested by Luis and that works for me.
Looking at the code I wonder if it makes sense to simplify the code
a little bit. The following works for me but I'm not sure how to
exercise the "NOERROR" codepath.
Signed-off-by: David S. Miller <davem@davemloft.net>
The ptrace_get_task_struct() helper that I added as part of the ptrace
consolidation is useful in variety of places that currently opencode it.
Switch them to the common helpers.
Add a ptrace_traceme() helper that needs to be explicitly called, and simplify
the ptrace_get_task_struct() interface. We don't need the request argument
now, and we return the task_struct directly, using ERR_PTR() for error
returns. It's a bit more code in the callers, but we have two sane routines
that do one thing well now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's definition is wrong (-1 means "no limit" not 999),
only the Sparc SunOS/Solaris compat code uses it, so
let's just kill it off completely from limits.h and
all referencing code.
Noticed by Ulrich Drepper.
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiple probes are registered at the same address and if due to some
recursion (probe getting triggered within a probe handler), we skip calling
pre_handlers and just increment nmissed field.
The below patch make sure it walks the list for multiple probes case.
Without the below patch we get incorrect results of nmissed count for
multiple probe case.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Earlier I unifdefed PageCompound, so that snd_pcm_mmap_control_nopage and
others can give out a 0-order component of a higher-order page, which won't
be mistakenly freed when zap_pte_range unmaps it. But many Bad page states
reported a PG_reserved was freed after all: I had missed that we need to
say __GFP_COMP to get compound page behaviour.
Some of these higher-order pages are allocated by snd_malloc_pages, some by
snd_malloc_dev_pages; or if SBUS, by sbus_alloc_consistent - but that has
no gfp arg, so add __GFP_COMP into its sparc32/64 implementations.
I'm still rather puzzled that DRM seems not to need a similar change.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a new function, sbusfb_compat_ioctl() to
drivers/video/sbuslib.c and uses it as compat_ioctl in all sbus fb
drivers
This remove the last per-arch compat ioctl bits in
arch/sparc64/kernel/ioctl32.c so it would be nice if people could test
if this actually copiles and works and if yes apply it :)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed by Tom 'spot' Callaway.
Even on uniprocessor we always reported the number of physical
cpus in the system via /proc/cpuinfo. But when this got changed
to use num_possible_cpus() it always reads as "1" on uniprocessor.
This change was unintentional.
So scan the firmware device tree and count the number of cpu
nodes, and report that, as we always did.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove a
duplicate of ARRAY_SIZE which is never used anyways.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make some changes to the NEED_RESCHED and POLLING_NRFLAG to reduce
confusion, and make their semantics rigid. Improves efficiency of
resched_task and some cpu_idle routines.
* In resched_task:
- TIF_NEED_RESCHED is only cleared with the task's runqueue lock held,
and as we hold it during resched_task, then there is no need for an
atomic test and set there. The only other time this should be set is
when the task's quantum expires, in the timer interrupt - this is
protected against because the rq lock is irq-safe.
- If TIF_NEED_RESCHED is set, then we don't need to do anything. It
won't get unset until the task get's schedule()d off.
- If we are running on the same CPU as the task we resched, then set
TIF_NEED_RESCHED and no further action is required.
- If we are running on another CPU, and TIF_POLLING_NRFLAG is *not* set
after TIF_NEED_RESCHED has been set, then we need to send an IPI.
Using these rules, we are able to remove the test and set operation in
resched_task, and make clear the previously vague semantics of
POLLING_NRFLAG.
* In idle routines:
- Enter cpu_idle with preempt disabled. When the need_resched() condition
becomes true, explicitly call schedule(). This makes things a bit clearer
(IMO), but haven't updated all architectures yet.
- Many do a test and clear of TIF_NEED_RESCHED for some reason. According
to the resched_task rules, this isn't needed (and actually breaks the
assumption that TIF_NEED_RESCHED is only cleared with the runqueue lock
held). So remove that. Generally one less locked memory op when switching
to the idle thread.
- Many idle routines clear TIF_POLLING_NRFLAG, and only set it in the inner
most polling idle loops. The above resched_task semantics allow it to be
set until before the last time need_resched() is checked before going into
a halt requiring interrupt wakeup.
Many idle routines simply never enter such a halt, and so POLLING_NRFLAG
can be always left set, completely eliminating resched IPIs when rescheduling
the idle task.
POLLING_NRFLAG width can be increased, to reduce the chance of resched IPIs.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Run idle threads with preempt disabled.
Also corrected a bugs in arm26's cpu_idle (make it actually call schedule()).
How did it ever work before?
Might fix the CPU hotplugging hang which Nigel Cunningham noted.
We think the bug hits if the idle thread is preempted after checking
need_resched() and before going to sleep, then the CPU offlined.
After calling stop_machine_run, the CPU eventually returns from preemption and
into the idle thread and goes to sleep. The CPU will continue executing
previous idle and have no chance to call play_dead.
By disabling preemption until we are ready to explicitly schedule, this bug is
fixed and the idle threads generally become more robust.
From: alexs <ashepard@u.washington.edu>
PPC build fix
From: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
MIPS build fix
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
