My patch "Separate pci bits out of struct device_node" (commit
1635317fac) had the unfortunate
side-effect that it stopped eeh_init() from working correctly.
It needs the pointers set up by find_and_init_phbs(), but it was being
called just before find_and_init_phbs(). That meant that we didn't
enable EEH (pSeries PCI error recovery) on any devices, and that meant
that on POWER5 systems, the hypervisor wouldn't let us enable memory or
I/O space access to any devices, and their drivers got somewhat
confused.
This fixes it by moving the eeh_init call after find_and_init_phbs.
Tested on a POWER5 partition.
Signed-of-by: Paul Mackerras <paulus@samba.org>
Signed-of-by: Linus Torvalds <torvalds@osdl.org>
ppc64_attention_msg and ppc64_dump_msg are not used so remove them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the rtas start-cpu token doesnt exist then presume the cpu is already
spinning. If it isnt we will catch it later on when the cpu doesnt
respond.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A few xics cleanups:
- Make some things static.
- Be more consistent with error printing - interrupts are unsigned,
error values are signed.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ptrace get and set methods for VMX/Altivec registers present in the
ppc tree were missing for ppc64. This patch adds the 32-bit and
64-bit methods. Updated with the suggestions from Anton following the lines
of his code snippet.
Added:
- flush_altivec_to_thread calls as suggested by Anton
- piecewise copy of structure to preserve 32-bit vrsave data as per
Anton
(I consolidated the 32 and 64bit versions with 2 helper macros - Anton)
Signed-off-by: Robert C Jennings <rcjenn@austin.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds code which gives us the option on ppc64 of instantiating the
PCI tree (the tree of pci_bus and pci_dev structs) from the Open
Firmware device tree rather than by probing PCI configuration space.
The OF device tree has a node for each PCI device and bridge in the
system, with properties that tell us what addresses the firmware has
configured for them and other details.
There are a couple of reasons why this is needed. First, on systems
with a hypervisor, there is a PCI-PCI bridge per slot under the PCI
host bridges. These PCI-PCI bridges have special isolation features
for virtualization. We can't write to their config space, and we are
not supposed to be reading their config space either. The firmware
tells us about the address ranges that they pass in the OF device
tree.
Secondly, on powermacs, the interrupt controller is in a PCI device
that may be behind a PCI-PCI bridge. If we happened to take an
interrupt just at the point when the device or a bridge on the path to
it was disabled for probing, we would crash when we try to access the
interrupt controller.
I have implemented a platform-specific function which is called for
each PCI bridge (host or PCI-PCI) to say whether the code should look
in the device tree or use normal PCI probing for the devices under
that bridge. On pSeries machines we use the device tree if we're
running under a hypervisor, otherwise we use normal probing. On
powermacs we use normal probing for the AGP bridge, since the device
for the AGP bridge itself isn't shown in the device tree (at least on
my G5), and the device tree for everything else.
This has been tested on a dual G5 powermac, a partition on a POWER5
machine (running under the hypervisor), and a legacy iSeries
partition.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is less troublesome and makes more sense.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the most trivial from Rusty's trivial patches:
- spelling fixes
- remove duplicate includes
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch (written by me and also containing many suggestions of Arjan van
de Ven) does a major cleanup of the spinlock code. It does the following
things:
- consolidates and enhances the spinlock/rwlock debugging code
- simplifies the asm/spinlock.h files
- encapsulates the raw spinlock type and moves generic spinlock
features (such as ->break_lock) into the generic code.
- cleans up the spinlock code hierarchy to get rid of the spaghetti.
Most notably there's now only a single variant of the debugging code,
located in lib/spinlock_debug.c. (previously we had one SMP debugging
variant per architecture, plus a separate generic one for UP builds)
Also, i've enhanced the rwlock debugging facility, it will now track
write-owners. There is new spinlock-owner/CPU-tracking on SMP builds too.
All locks have lockup detection now, which will work for both soft and hard
spin/rwlock lockups.
The arch-level include files now only contain the minimally necessary
subset of the spinlock code - all the rest that can be generalized now
lives in the generic headers:
include/asm-i386/spinlock_types.h | 16
include/asm-x86_64/spinlock_types.h | 16
I have also split up the various spinlock variants into separate files,
making it easier to see which does what. The new layout is:
SMP | UP
----------------------------|-----------------------------------
asm/spinlock_types_smp.h | linux/spinlock_types_up.h
linux/spinlock_types.h | linux/spinlock_types.h
asm/spinlock_smp.h | linux/spinlock_up.h
linux/spinlock_api_smp.h | linux/spinlock_api_up.h
linux/spinlock.h | linux/spinlock.h
/*
* here's the role of the various spinlock/rwlock related include files:
*
* on SMP builds:
*
* asm/spinlock_types.h: contains the raw_spinlock_t/raw_rwlock_t and the
* initializers
*
* linux/spinlock_types.h:
* defines the generic type and initializers
*
* asm/spinlock.h: contains the __raw_spin_*()/etc. lowlevel
* implementations, mostly inline assembly code
*
* (also included on UP-debug builds:)
*
* linux/spinlock_api_smp.h:
* contains the prototypes for the _spin_*() APIs.
*
* linux/spinlock.h: builds the final spin_*() APIs.
*
* on UP builds:
*
* linux/spinlock_type_up.h:
* contains the generic, simplified UP spinlock type.
* (which is an empty structure on non-debug builds)
*
* linux/spinlock_types.h:
* defines the generic type and initializers
*
* linux/spinlock_up.h:
* contains the __raw_spin_*()/etc. version of UP
* builds. (which are NOPs on non-debug, non-preempt
* builds)
*
* (included on UP-non-debug builds:)
*
* linux/spinlock_api_up.h:
* builds the _spin_*() APIs.
*
* linux/spinlock.h: builds the final spin_*() APIs.
*/
All SMP and UP architectures are converted by this patch.
arm, i386, ia64, ppc, ppc64, s390/s390x, x64 was build-tested via
crosscompilers. m32r, mips, sh, sparc, have not been tested yet, but should
be mostly fine.
From: Grant Grundler <grundler@parisc-linux.org>
Booted and lightly tested on a500-44 (64-bit, SMP kernel, dual CPU).
Builds 32-bit SMP kernel (not booted or tested). I did not try to build
non-SMP kernels. That should be trivial to fix up later if necessary.
I converted bit ops atomic_hash lock to raw_spinlock_t. Doing so avoids
some ugly nesting of linux/*.h and asm/*.h files. Those particular locks
are well tested and contained entirely inside arch specific code. I do NOT
expect any new issues to arise with them.
If someone does ever need to use debug/metrics with them, then they will
need to unravel this hairball between spinlocks, atomic ops, and bit ops
that exist only because parisc has exactly one atomic instruction: LDCW
(load and clear word).
From: "Luck, Tony" <tony.luck@intel.com>
ia64 fix
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjanv@infradead.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Mikael Pettersson <mikpe@csd.uu.se>
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts the final 20 DEFINE_SPINLOCK holdouts. (another 580 places
are already using DEFINE_SPINLOCK). Build tested on x86.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pciconfig_iobase, pciconfig_read and pciconfig_write system calls
were only implemented for 32-bit processes; for 64-bit processes they
returned an ENOSYS error. This allows them to be used by 64-bit
processes as well. The X server uses pciconfig_iobase at least, and
this change is necessary to allow a 64-bit X server to work on my G5.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch pulls the PCI-related junk out of struct device_node and
puts it in a separate structure, struct pci_dn. The device_node now
just has a void * pointer in it, which points to a struct pci_dn for
nodes that represent PCI devices. It could potentially be used in
future for device-specific data for other sorts of devices, such as
virtual I/O devices.
Signed-off-by: Paul Mackerras <paulus@samba.org>
In PPC64 there are number of problems in arch/ppc64/boot/main.c that
prevent a kernel from making use of a large (greater than ~16MB) INITRD.
This is 64 bit architecture and really large INITRD images should be
possible.
Simply put the existing code has a fixed reservation (claim) address and
once the kernel plus initrd image are large enough to pass this address
all sorts of bad things occur. The fix is the dynamically establish the
first claim address above the loaded kernel plus initrd (plus some
"padding" and rounding). If PROG_START is defined this will be used as
the minimum safe address - currently known to be 0x01400000 for the
firmwares tested so far.
Signed-off-by: Mark Bellon <mbellon@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch cleans up the output generated by ppc64 builds.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make check_bugs() static inline and remove it from syscalls.c.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The earlier commit 8d92739186
(Consolidate early console and PPCDBG code) broke iSeries because
it caused unregister_console(&udbg_console) to be called
unconditionally. iSeries never registers the udbg_console.
This just reverts part of the change.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SPARSEMEM EXTREME code (802f192e4a) that
went in yesterday broke PPC64 for !CONFIG_NUMA.
The problem is that (free|reserve)_bootmem don't take a page number as their
first argument, they take an address. Ruh roh.
Booted on P5 LPAR, iSeries and G5.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a severe bug in the bpa_iic driver that caused
all sorts of problems.
We had been using incorrect priority values for inter processor
interrupts, which resulted in always doing CALL_FUNCTION
instead of RESCHEDULE or DEBUGGER_BREAK.
The symptoms cured by this patch include bad performance on
SMP systems spurious kernel panics in the IPI code.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rather than hard-coding the platform device IDs, enumerate them.
We don't particularly care about the actual ID we get, just as
long as they're unique.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that asm-powerpc/* is using ifdefs on __powerpc64__ we need to add it
to CHECKFLAGS on ppc64.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sanitized and fixed floppy dependencies: split the messy dependencies for
BLK_DEV_FD by introducing a new symbol (ARCH_MAY_HAVE_PC_FDC), making
BLK_DEV_FD depend on that one and taking declarations of ARCH_MAY_HAVE_PC_FDC
to arch/*/Kconfig. While we are at it, fixed several obvious cases when
BLK_DEV_FD should have been excluded (architectures lacking asm/floppy.h
are *not* going to have floppy.c compile, let alone work).
If you can come up with better name for that ("this architecture might
have working PC-compatible floppy disk controller"), you are more than
welcome - just s/ARCH_MAY_HAVE_PC_FDC/your_prefered_name/g in the patch
below...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a race condition where in system used to hang or sometime
crash within minutes when kprobes are inserted on ISR routine and a task
routine.
The fix has been stress tested on i386, ia64, pp64 and on x86_64. To
reproduce the problem insert kprobes on schedule() and do_IRQ() functions
and you should see hang or system crash.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the ppc64 architecture specific changes to prevent the
possible race conditions.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
64 bit architectures all implement their own compatibility sys_open(),
when in fact the difference is simply not forcing the O_LARGEFILE
flag. So use the a common function instead.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <viro@parcelfarce.linux.theplanet.co.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch cleans up a commonly repeated set of changes to the NTP state
variables by adding two helper inline functions:
ntp_clear(): Clears the ntp state variables
ntp_synced(): Returns 1 if the system is synced with a time server.
This was compile tested for alpha, arm, i386, x86-64, ppc64, s390, sparc,
sparc64.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changing CONFIG_LOCALVERSION rebuilds too much, for no apparent reason.
Use system_utsname for progress and debug header.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, we set the class bit in kernel SLB entries, and clear it on
user SLB entries. On POWER5, ERAT entries created in real mode have
the class bit clear. So to avoid flushing kernel ERAT entries on each
context switch, this patch inverts our usage of the class bit, setting
it on user SLB entries and clearing it on kernel SLB entries.
Booted on POWER5 and G5.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move oprofile_impl.h into include/asm-ppc64 in preparation for moving
oprofile_model into cpu feature struct.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change oprofile to use num_pmcs from the cpu feature struct.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the CPU_FTR_PMC8 feature now we encode the number of PMCs
directly.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a field in the cputable struct to store the number of PMCs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I would like to be able to read the lparcfg data from any user so we
can make "intelligent" decisions based on underlying attributes when
running in lpars. Yes there's software that likes to do this :) and
runs as non-root.
It's very similar to say VM where you can get CP to provide feedback
of the real hardware inside a VM guest.
Signed-off-by: Wim Coekaerts <wim.coekaerts@oracle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Removed PPC64 architecture specific users of asm/segment.h.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Poison initmem after we free it so we catch use after free issues.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch fixes 2 issues:
1) use PLATFORM_LPAR bit to test if running in LPAR mode
2) systemcfg pointer is assigned from static data in
arch/ppc64/kernel/pacaData.c. The file arch/ppc64/kernel/head.S
now refers to is using the GOT binding to the pointer and hence
must deref it.
Signed-off-by: Jimi Xenidis <jimix@watson.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Consolidate the early console and PPCDBG code in udbg.c
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Trim some no longer needed includes from udbg.c and friends.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Take udbg out of ppc_md. Allows us to not overwrite early udbg inits
when assigning ppc_md.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split scc and 15550 functions from udbg each into their own file.
This makes them more symetric with the lpar and btext code.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
make udbg_init_uart set the ppc_md udbg methods.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make the 16550 and real mode 16550 use tail recursion like the scc code
instead of repeating the routine except for the character sent.
Gcc recoginizes the tail recursion and handles it efficently without
stack allocations. The maple real putc shrinks from 188 to 104 bytes
of instructions. udbg_putc drops from 188 to 140 bytes.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that xmon is fixed we should not need the dummy getc routines.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
udbg_getc_poll is a ppc_md function. don't call directly into udbg.c
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use msleep_interruptible() instead of schedule_timeout() in ppc64-specific
code to cleanup/simplify the sleeping logic. Change the units of the
parameter of do_event_scan_all_cpus() to milliseconds from jiffies. The
return value of rtas_extended_busy_delay_time() was incorrectly being used
as a jiffies value (it is actually milliseconds), which is fixed by using
the value as a parameter to msleep_interruptible(). Also, use
rtas_extended_busy_delay_time() in another case where similar logic is
duplicated.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to indicate to the hypervisor that it needs to save our VMX
registers when switching partitions on a shared-processor system, just as
it needs to for FP and PMC registers.
This could be made to be on-demand when VMX is used, but we don't do that
for FP nor PMC right now either so let's not overcomplicate things.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: <engebret@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
xmon will do nothing but noise on a G5 if BOOTX_TEXT is not enabled.
mention the recognized kernel cmdline options for xmon.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Paul Mackeras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A new option for SPARSEMEM is ARCH_SPARSEMEM_EXTREME. Architecture
platforms with a very sparse physical address space would likely want to
select this option. For those architecture platforms that don't select the
option, the code generated is equivalent to SPARSEMEM currently in -mm.
I'll be posting a patch on ia64 ml which uses this new SPARSEMEM feature.
ARCH_SPARSEMEM_EXTREME makes mem_section a one dimensional array of
pointers to mem_sections. This two level layout scheme is able to achieve
smaller memory requirements for SPARSEMEM with the tradeoff of an
additional shift and load when fetching the memory section. The current
SPARSEMEM -mm implementation is a one dimensional array of mem_sections
which is the default SPARSEMEM configuration. The patch attempts isolates
the implementation details of the physical layout of the sparsemem section
array.
ARCH_SPARSEMEM_EXTREME depends on 64BIT and is by default boolean false.
I've boot tested under aim load ia64 configured for ARCH_SPARSEMEM_EXTREME.
I've also boot tested a 4 way Opteron machine with !ARCH_SPARSEMEM_EXTREME
and tested with aim.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In adjusting the logic for SLB miss for the dynamic hugepage stuff, I
messed up the !CONFIG_HUGETLB_PAGE case, failing to set the SLB flags
properly.
This fixes it. It also streamlines the logic for the HUGETLB_PAGE case
(removing a couple of branches) while we're at it.
Booted, and roughly tested on POWER5 (with and without HUGETLB_PAGE),
iSeries/RS64 (no hugepage available), and G5 (with and without
HUGETLB_PAGE).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The {BEGIN,END}_FTR_SECTION asm macros used in ppc64 to nop out
sections of code at runtime cannot be nested. However, we do nest
them in hash_low.S. We get away with it there, because there is
nothing between the BEGIN markers for each section. However, that's
confusing to someone reading the code.
This patch removes the nested ifset and ifclr feature sections,
replacing them with a single feature section in the full mask/value
form.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a rare memory leak found by Coverity.
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
While ppc64 has the CONFIG_HZ Kconfig option, it wasnt actually being
used. Connect it up and set all platforms to 250Hz.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's the 970MP's PVR (processor version register) entry for oprofile.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some RS64-based machines (p620, F80, others) have problems with firmware
returning 0xdeadbeef instead of failure to allocations that end at the
1GB mark.
We have two options:
1. Detect the undocumented 0xdeadbeef return value and interpret it as
a failure.
2. Avoid allocating that high.
(2) is really the cleaner solution here. 768MB is plenty of room so use
that as the max alloc_top instead of 1GB.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ppc and ppc64 trees are hopefully going to merge over time, so this
patch begins the process by creating a place for the merging of the
header files.
Create include/asm-powerpc (and move linkage.h into it from
asm-{ppc,ppc64} since we don't like empty directories). Modify the
ppc and ppc64 Makefiles to cope.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Create vio_bus_ops so that we just pass a structure to vio_bus_init
instead of three separate function pointers.
Rearrange vio.h to avoid forward references. vio.h only needs
struct device_node from prom.h so remove the include and just
declare it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Take some assignments out of vio_register_device_common and
rename it to vio_register_device.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Formatting changes to vio.c to bring it closer to the
kernel coding standard.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
gcc 3.4 (at least the build we are using) puts the gcc generated .ident
string into a .note section at the end of the files it compiles (gcc
3.3.3-hammer and gcc 4.0.2 Debian puts it in the .text section). This
means that the lparmap.s file we produce in the iSeries build may end with
a .note section. When we include it into head.S, the assembler can no
longer resolve some of the conditional branches since the target label
ends up too far away. This patch just forces us back to the .text section
after including lparmap.s.
The breakage was caused by my patch "iSeries build with newer assemblers
and compilers" (sha1-id: 2ad5649662).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A mistake rebasing the series of ppc64 head.S cleanup patches meant
the #include of lparmap.s, needed for iSeries was lost. This patch
puts it back again.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It has been reported that the way Linux handles NODEFER for signals is
not consistent with the way other Unix boxes handle it. I've written a
program to test the behavior of how this flag affects signals and had
several reports from people who ran this on various Unix boxes,
confirming that Linux seems to be unique on the way this is handled.
The way NODEFER affects signals on other Unix boxes is as follows:
1) If NODEFER is set, other signals in sa_mask are still blocked.
2) If NODEFER is set and the signal is in sa_mask, then the signal is
still blocked. (Note: this is the behavior of all tested but Linux _and_
NetBSD 2.0 *).
The way NODEFER affects signals on Linux:
1) If NODEFER is set, other signals are _not_ blocked regardless of
sa_mask (Even NetBSD doesn't do this).
2) If NODEFER is set and the signal is in sa_mask, then the signal being
handled is not blocked.
The patch converts signal handling in all current Linux architectures to
the way most Unix boxes work.
Unix boxes that were tested: DU4, AIX 5.2, Irix 6.5, NetBSD 2.0, SFU
3.5 on WinXP, AIX 5.3, Mac OSX, and of course Linux 2.6.13-rcX.
* NetBSD was the only other Unix to behave like Linux on point #2. The
main concern was brought up by point #1 which even NetBSD isn't like
Linux. So with this patch, we leave NetBSD as the lonely one that
behaves differently here with #2.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paulus, I think this is now a reasonable candidate for the post-2.6.13
queue.
Relax address restrictions for hugepages on ppc64
Presently, 64-bit applications on ppc64 may only use hugepages in the
address region from 1-1.5T. Furthermore, if hugepages are enabled in
the kernel config, they may only use hugepages and never normal pages
in this area. This patch relaxes this restriction, allowing any
address to be used with hugepages, but with a 1TB granularity. That
is if you map a hugepage anywhere in the region 1TB-2TB, that entire
area will be reserved exclusively for hugepages for the remainder of
the process's lifetime. This works analagously to hugepages in 32-bit
applications, where hugepages can be mapped anywhere, but with 256MB
(mmu segment) granularity.
This patch applies on top of the four level pagetable patch
(http://patchwork.ozlabs.org/linuxppc64/patch?id=1936).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
You can't call get_property() on a NULL node, so check if of_chosen is set
in check_for_initrd().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
arch/ppc64/kernel/setup.c | 20 ++++++++++++--------
1 files changed, 12 insertions(+), 8 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
unflatten_device_tree() doesn't check if lmb_alloc() succeeds or not, it
should. All it can do is panic, but at least there's an error message
(assuming you have some sort of console at that point).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
arch/ppc64/kernel/prom.c | 9 +++++++--
1 files changed, 7 insertions(+), 2 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
When unflatten_dt_node() fails to find an OF_DT_END_NODE tag it prints
"Weird tag at start of node", this should be "Weird tag at end of node".
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
arch/ppc64/kernel/prom.c | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves power4_enable_pmcs() to arch/ppc64/kernel/pmc.c.
I've tested it on P5 LPAR and P4. It does what it used to.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If both CONFIG_XMON and CONFIG_XMON_DEFAULT is enabled in the .config,
there is no way to disable xmon again. setup_system calls first xmon_init,
later parse_early_param. So a new 'xmon=off' cmdline option will do the right
thing.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We can now remove CONFIG_MSCHUNKS as it doesn't do anything interesting
anymore.
The only macro in abs_addr.h which is called by non-iSeries code is
phys_to_abs(), so remove the other dummy implementations, and we add a
firmware feature check to phys_to_abs().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
lmb_phys_mem_size() can always return lmb.memory.size, as long as it's called
after lmb_analyze(), which it is. There's no need to recalculate the size on
every call.
lmb_analyze() was calculating a few things we then threw away, so just don't
calculate them to start with.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We no longer need the lmb code to know about abs and phys addresses, so
remove the physbase variable from the lmb_property struct.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
abs_to_phys() is a macro that turns out to do nothing, and also has the
unfortunate property that it's not the inverse of phys_to_abs() on iSeries.
The following is for my benefit as much as everyone else.
With CONFIG_MSCHUNKS enabled, the lmb code is changed such that it keeps
a physbase variable for each lmb region. This is used to take the possibly
discontiguous lmb regions and present them as a contiguous address space
beginning from zero.
In this context each lmb region's base address is its "absolute" base
address, and its physbase is it's "physical" address (from Linux's point of
view). The abs_to_phys() macro does the mapping from "absolute" to "physical".
Note: This is not related to the iSeries mapping of physical to absolute
(ie. Hypervisor) addresses which is maintained with the msChunks structure.
And the msChunks structure is not controlled via CONFIG_MSCHUNKS.
Once upon a time you could compile for non-iSeries with CONFIG_MSCHUNKS
enabled. But these days CONFIG_MSCHUNKS depends on CONFIG_PPC_ISERIES, so
for non-iSeries code abs_to_phys() is a no-op.
On iSeries we always have one lmb region which spans from 0 to
systemcfg->physicalMemorySize (arch/ppc64/kernel/iSeries_setup.c line 383).
This region has a base (ie. absolute) address of 0, and a physbase address
of 0 (as calculated in lmb_analyze() (arch/ppc64/kernel/lmb.c line 144)).
On iSeries, abs_to_phys(aa) is defined as lmb_abs_to_phys(aa), which finds
the lmb region containing aa (and there's only one, ie. 0), and then does:
return lmb.memory.region[0].physbase + (aa - lmb.memory.region[0].base)
physbase == base == 0, so you're left with "return aa".
So remove abs_to_phys(), and lmb_abs_to_phys() which is the implementation
of abs_to_phys() for iSeries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The lmb code is all written to use a pointer to an lmb struct. But it's always
the same lmb struct, called "lmb". So we take the address of lmb, call it
_lmb and then start using _lmb->foo everywhere, which is silly.
This patch removes the _lmb pointers and replaces them with direct references
to the one "lmb" struct. We do the same for some _mem and _rsv pointers which
point to lmb.memory and lmb.reserved respectively.
This patch looks quite busy, but it's basically just:
s/_lmb->/lmb./g
s/_mem->/lmb.memory./g
s/_rsv->/lmb.reserved./g
s/_rsv/&lmb.reserved/g
s/mem->/lmb.memory./g
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
physRpn_to_absRpn is a no-op on non-iSeries platforms, remove the two
redundant calls.
There's only one caller on iSeries so fold the logic in there so we can get
rid of it completely.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename the msChunks struct to get rid of the StUdlY caps and make it a bit
clearer what it's for.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Chunks are 256KB, so use constants for the size/shift/mask, rather than
getting them from the msChunks struct. The iSeries debugger (??) might still
need access to the values in the msChunks struct, so we keep them around
for now, but set them from the constant values.
Replace msChunks_entry typedef with regular u32.
Simplify msChunks_alloc() to manipulate klimit directly, rather than via
a parameter.
Move msChunks_alloc() and msChunks into iSeries_setup.c, as that's where
they're used.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The msChunks code was written to work on pSeries, but now it's only used on
iSeries. This means there's no need to do PTRRELOC anymore, so remove it all.
A few places were getting "extern reloc_offset()" from abs_addr.h, move it
into system.h instead.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make firmware_has_feature() evaluate at compile time for the non pSeries
case and tidy up code where possible.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Create the firmware_has_feature() inline and move the firmware feature
stuff into its own header file.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The firmware_features field of struct cpu_spec should really be a separate
variable as the firmware features do not depend on the chip and the
bitmask is constructed independently. By removing it, we save 112 bytes
from the cpu_specs array and we access the bitmask directly instead of via
the cur_cpu_spec pointer.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ppc64 head.S defines several zero-initialized structures, such as
the empty_zero_page and the kernel top-level pagetable. Currently
they are defined to be in the data section. However, they're not used
until after the bss is cleared, so this patch moves them to the bss,
saving two and a half pages from the vmlinux.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adjust some comments in head.S for accuracy, clarity, and
spelling.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/ppc64/kernel/head.S #defines SECONDARY_PROCESSORS then has some
#ifdefs based on it. Whatever purpose this had is long lost, this
patch removes it.
Likewise, head.S defines H_SET_ASR, which is now defined, along with
other hypervisor call numbers in hvcall.h. This patch deletes it, as
well, from head.S.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
An #if/#else construct near the top of ppc64's head.S appears to
create overlapping sections of code for iSeries and pSeries (i.e. one
thing on iSeries and something different in the same place on
pSeries). In fact, checking the various absolute offsets, it doesn't.
This patch unravels the #ifdefs to make it more obvious what's going
on. This accomplishes another microstep towards a single kernel image
which can boot both iSeries and pSeries.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As well as the interrupt vectors and initialization code, head.S
contains several asm functions which are used during runtime. This
patch moves these to misc.S, a more sensible location for random asm
support code. A couple The functions moved are:
disable_kernel_fp
giveup_fpu
disable_kernel_altivec
giveup_altivec
__setup_cpu_power3 (empty function)
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On ppc64 machines with segment tables, CPU0's segment table is at a
fixed address, currently 0x9000. This patch moves it to the free
space at 0x6000, just below the fwnmi data area. This saves 8k of
space in vmlinux and the runtime kernel image.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the ppc64 kernel head.S there is currently quite a lot of unused
space between the naca (at fixed address 0x4000) and the fwnmi data
area (at fixed address 0x7000). This patch moves various exception
vectors and support code into this region to use the wasted space.
The functions load_up_fpu and load_up_altivec are moved down as well,
since they are essentially continuations of the fp_unavailable_common
and altivec_unavailable_common vectors, respectively.
Likewise, the fwnmi vectors themselves are moved down into this area,
because while the location of the fwnmi data area is fixed by the RPA,
the vectors themselves can be anywhere sufficiently low.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Comments in head.S suggest that the iSeries naca has a fixed address,
because tools expect to find it there. The only tool which appears to
access the naca is addRamDisk, but both the in-kernel version and the
version used in RHEL and SuSE in fact locate the NACA the same way as
the hypervisor does, by following the pointer in the hvReleaseData
structure.
Since the requirement for a fixed address seems to be obsolete, this
patch removes the naca from head.S and replaces it with a normal C
initializer.
For good measure, it removes an old version of addRamDisk.c which was
sitting, unused, in the ppc32 tree.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch just splits out the pSeries specific parts of vio.c.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch allows us to have a different bus if matching function for
each platform.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the iSeries vio iommu tables cannot be used until after the vio bus has
been initialised, move the initialisation of the tables to there.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch splits the iSeries specific parts out of vio.c.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/ppc64/Kconfig defines a "General setup" menu, but also sources
init/Kconfig which also defines a "General setup" menu. Both of these
menus appear at the top level of make menuconfig. Having two menus with
the same name is confusing. This patch renames the ppc64/Kconfig menu to
be "Bus Options" and moves options in this menu which are not bus related
to the end of the "Platform support" menu.
There are many variations among architectures on the exact naming of the
"Bus Options" menu. I chose to use the simplest one, which is also used
in arch/ppc/Kconfig.
Signed-off-by: Frank Rowand <frowand@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
OpenFirmware marks devices as failed in the device-tree when a hardware
problem is detected. The kernel needs to fail config reads/writes to
prevent a kernel crash when incorrect data is read.
This patch validates that the device-node is not marked "fail" when
config space reads/writes are attempted.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch updates the format of the flattened device-tree passed
between the boot trampoline and the kernel to support a more compact
representation, for use by embedded systems mostly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement 4-level pagetables for ppc64
This patch implements full four-level page tables for ppc64, thereby
extending the usable user address range to 44 bits (16T).
The patch uses a full page for the tables at the bottom and top level,
and a quarter page for the intermediate levels. It uses full 64-bit
pointers at every level, thus also increasing the addressable range of
physical memory. This patch also tweaks the VSID allocation to allow
matching range for user addresses (this halves the number of available
contexts) and adds some #if and BUILD_BUG sanity checks.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make the bootheader for ppc64 independent from kernel and libc headers.
* add -nostdinc -isystem $gccincludes to not include libc headers
* declare all functions in header files, also the stuff from string.S
* declare some functions static
* use stddef.h to get size_t (hopefully ok)
* remove ppc32-types.h, only elf.h used the __NN types
With further modifications by Paul Mackerras and Stephen Rothwell.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we leave sigsuspend() directly into a signal handler, we don't want
to go via the normal syscall exit path -- it'll corrupt r4 and r5 which
are supposed to be giving information to the signal handler, and it'll
give us one more single-step SIGTRAP than we need if single-stepping is
in operation.
However, we _should_ be calling audit_syscall_exit(), which would
normally get invoked in that patch. It's not wonderfully pretty, but I
suspect the best answer is just to call it directly...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch puts back the export of machine_power_off() that was removed
by some janitor as it's used for emergency shutdown by the G5 thermal
control driver. Wether that driver should use kernel_power_off() instead
is debatable and a post-2.6.13 decision. In the meantime, please commit
that patch that fixes the driver for now.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a bug in the PPC64 iommu vmerge code which results in the
potential for iommu_unmap_sg to go off unmapping more than it should.
This was found on a test system which resulted in PCI bus errors due to
PCI memory being unmapped while DMAs were still in progress.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paulus suggested that we put xLparMap in its own .c file so that we can
generate a .s file to be included into head.S. This doesn't get around
the problem of having it at a fixed address, but it makes it more
palatable.
It would be good if this could be included in 2.6.13 as it solves our
build problems with various versions of binutils and gcc. In
particular, it allows us to build an iSeries kernel on Debian unstable
using their biarch compiler.
This has been built and booted on iSeries and built for pSeries and g5.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The workaround for broken device-tree that prevents fan control from
working on recent G5 models need to be "enabled" for machines with
revision 0x37 of the bridge in addition to machines with revision 0x35.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds a bpa_defconfig file and make target. The config settings
are made for the current version of the Cell Processor Based Blade,
so there are not too many drivers enabled. A few more drivers might
get added in the future though.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In yenta_socket, we default to using the resource setting of the CardBus
bridge. However, this is a PCI-bus-centric view of resources and thus needs
to be converted to generic resources first. Therefore, add a call to
pcibios_bus_to_resource() call in between. This function is a mere wrapper on
x86 and friends, however on some others it already exists, is added in this
patch (alpha, arm, ppc, ppc64) or still needs to be provided (parisc -- where
is its pcibios_resource_to_bus() ?).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kexec boot is not successful on some power machines since all CPUs are
getting removed from global interrupt queue (GIQ) before kexec boot. Some
systems always expect at least one CPU in GIQ. Hence, this patch will make
sure that only secondary CPUs are removed from GIQ.
Signed-off-by: Haren Myneni <hbabu@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_KEXEC breaks UP builds because of a misspelled smp_release_cpus().
Also, the function isn't defined unless built with CONFIG_SMP but it is
needed if we are to go from a UP to SMP kernel. Enable it and document it.
Thanks to Steven Winiecki for reporting this and to Milton for remembering
how it's supposed to work and why.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For soft reset during system hang, got an error "CPU did not take
control" for some CPUs even though they responded to soft-reset (called
SystemReset, die and called debugger - xmon). First these CPUs entered
into xmon by IPI callback and then got a soft-reset exception and
re-entered into xmon again. The first CPU which re-entered into xmon got
the output lock and made into xmon successfully without unlocking.
Hence, the next CPU(s) which re-entered into xmon try to acquire a lock
(get_output_lock). Therefore, we can not view state of those CPU(s).
[This is a simple, very low risk, obvious fix for an obvious bug, and
should go into 2.6.13. -- paulus]
Signed-off-by: Haren Myneni <hbabu@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If CONFIG_NUMA is set, some POWER 4 systems will fail to boot. This is
because of special processing needed to handle invalid node IDs (0xffff) on
POWER 4. My previous patch to handle memory 'holes' within nodes forgot to
add this special case for POWER 4 in one place.
In reality, I'm not sure that configuring the kernel for NUMA on POWER 4 makes
much sense. Are there POWER 4 based systems with NUMA characteristics that
are presented by the firmware? But, distros want one kernel for all systems
so NUMA is on by default in their kernels. The patch handles those cases.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code that sets the altivec capability of the CPU based on firmware
informations can enable altivec when the kernel has CONFIG_ALTIVEC
disabled. This results in "interesting" crashes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
inotify system call support for PPC64
[ I don't think we need sys32 compatibility versions--and if we do, I
failed in life. ]
Signed-off-by: Robert Love <rml@novell.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
turn many #if $undefined_string into #ifdef $undefined_string to fix some
warnings after -Wno-def was added to global CFLAGS
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Presently the LparMap, one of the structures the kernel shares with the
legacy iSeries hypervisor has a fixed offset address in head.S. This patch
changes this so the LparMap is a normally initialized structure, without
fixed address. This allows us to use macros to compute some of the values
in the structure, which wasn't previously possible because the assembler
always uses signed-% which gets the wrong answers for the computations in
question.
Unfortunately, a gcc bug means that doing this requires another structure
(hvReleaseData) to be initialized in asm instead of C, but on the whole the
result is cleaner than before.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PPC64 machines before Power4 need a segment table page allocated for each
CPU. Currently these are allocated statically in a big array in head.S for
all CPUs. The segment tables need to be in the first segment (so
do_stab_bolted doesn't take a recursive fault on the stab itself), but
other than that there are no constraints which require the stabs for the
secondary CPUs to be statically allocated.
This patch allocates segment tables dynamically during boot, using
lmb_alloc() to ensure they are within the first 256M segment. This reduces
the kernel image size by 192k...
Tested on RS64 iSeries, POWER3 pSeries, and POWER5.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
update defconfig, use new CONFIG_HZ and set it to 100 just for the kicks.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
use new Kconfig.hz on ppc/ppc64, use also Kconfig.preempt for ppc
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
machine_restart, machine_halt and machine_power_off are machine
specific hooks deep into the reboot logic, that modules
have no business messing with. Usually code should be calling
kernel_restart, kernel_halt, kernel_power_off, or
emergency_restart. So don't export machine_restart,
machine_halt, and machine_power_off so we can catch buggy users.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add PVR value and tests for 970MP. Also switch to a simpler (but slightly
longer) check at init time for simplicity.
Signed-off-by: Olof Johansson <olof@austin.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the use of bitfield types from the ppc64 hash table
manipulation code.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create a new top-level menu named "Networking" thus moving
net related options and protocol selection way from the drivers
menu and up on the top-level where they belong.
To implement this all architectures has to source "net/Kconfig" before
drivers/*/Kconfig in their Kconfig file. This change has been
implemented for all architectures.
Device drivers for ordinary NIC's are still to be found
in the Device Drivers section, but Bluetooth, IrDA and ax25
are located with their corresponding menu entries under the new
networking menu item.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dont need to use the PERFMON exception on POWER5, in fact the firmware
returns an error. Due to this just remove the warning.
Also now that we have proper runlatch support we can remove the bootup
hack.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not sure if we really need this, but it was handy to know which iSeries loop I
was testing.
Be consistent about printing which idle loop we're using, with this patch we
cover all cases.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a compile warning introduced by the previous patches.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- remove some unnecessary includes
- add runlatch support
- no need to use raw_smp_processor_id any more, current preempt debug
logic checks for processes that are bound to one cpu.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- separate out sleep logic in dedicated_idle, it was so far indented
that it got squashed against the right side of the screen.
- add runlatch support, looping on runlatch disable.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- remove min/max yield time, we dont use the values anywhere
- separate shared and dedicated idle loops
- check need_resched again with irqs off to avoid sleeping with pending work
- continually set runlatch off in idle loop, this means we dont need to
turn the runlatch off on exception exit and suffer that associated
cost for all exceptions. (A future patch will turn the runlatch on at
exception entry)
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that the idle loop is configured by each platform we don't need
idle_setup() anymore.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes up iSeries, pSeries, pmac and maple to set the correct idle
function for each platform.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dedicated_idle() and shared_idle() are only used by pSeries, so move them into
pSeries_setup.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
