Mark sunsu_console_setup() as __init and rename 'sunsu_cons'
to 'sunsu_console' so that it matches modpost.c's whitelist.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the enable/disable hooks for the port clock to sh-sci.
Signed-off-by: dmitry pervushin <dimka@nomadgs.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the GDB stub being entered via a special sysrq trigger,
we don't want to hit it directly from sci_br_interrupt().
Without this, there is access to the other sysrq triggers when
kgdb is enabled.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7785-based Highlander board.
Some of the Highlander support code is reordered so that most of it
can be reused directly.
This also plugs in missing SH7785 checks in the places that need it,
as this is the first board to support the CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code has suffered quite a bit of bitrot, do some basic
tidying to get it to a reasonably functional state again.
This gets the basic support and the console working again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch moves the i.MX UART register descriptions from
include/asm-arm/arch-imx/imx-regs.h to the serial driver itself.
This helps using the driver on other architectures like mx31
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow slower serial baud-rates by switching the UART clock from MCK to
MCK/8.
Based on patches by Mike Wolfram and Russell King.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These are all the remaining instances of get_property. Simple rename of
get_property to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The only unfortunate bit here is that the name field of struct map_info
is not const, so for now we put a cast on the assignment of it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 40b36daa introduced possibility that serial8250_backup_timeout() ->
serial8250_handle_port() locks port.lock without disabling irqs, thus
allowing deadlock against interrupt handler (port.lock is acquired in
serial8250_interrupt()).
Spotted by lockdep.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two functions are called from __devinit context, but they are marked as
__init. Fix this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
irq values are u32, not u8. Large irq numbers will be truncated,
free_irq may free a different irq.
Remove incorrectly sized struct member and use the one from pci_dev.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I encountered the following kernel panic. The cause of this problem was
NULL pointer access in check_modem_status() in 8250.c. I confirmed this
problem is fixed by the attached patch, but I don't know this is the
correct fix.
sadc[4378]: NaT consumption 2216203124768 [1]
Modules linked in: binfmt_misc dm_mirror dm_mod thermal processor fan
container button sg e100 eepro100 mii ehci_hcd ohci_hcd
Pid: 4378, CPU 0, comm: sadc
psr : 00001210085a2010 ifs : 8000000000000289 ip : [<a000000100482071>]
Not tainted
ip is at check_modem_status+0xf1/0x360
Call Trace:
[<a000000100013940>] show_stack+0x40/0xa0
[<a0000001000145a0>] show_regs+0x840/0x880
[<a0000001000368e0>] die+0x1c0/0x2c0
[<a000000100036a30>] die_if_kernel+0x50/0x80
[<a000000100037c40>] ia64_fault+0x11e0/0x1300
[<a00000010000bdc0>] ia64_leave_kernel+0x0/0x280
[<a000000100482070>] check_modem_status+0xf0/0x360
[<a000000100482300>] serial8250_get_mctrl+0x20/0xa0
[<a000000100478170>] uart_read_proc+0x250/0x860
[<a0000001001c16d0>] proc_file_read+0x1d0/0x4c0
[<a0000001001394b0>] vfs_read+0x1b0/0x300
[<a000000100139cd0>] sys_read+0x70/0xe0
[<a00000010000bc20>] ia64_ret_from_syscall+0x0/0x20
[<a000000000010620>] __kernel_syscall_via_break+0x0/0x20
Fix the possible NULL pointer access in check_modem_status() in 8250.c. The
check_modem_status() would access 'info' member of uart_port structure, but it
is not initialized before uart_open() is called. The check_modem_status() can
be called through /proc/tty/driver/serial before uart_open() is called.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Taku Izumi <izumi2005@soft.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace uses with of_find_node_by_name and for_each_node_by_name.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert the AMBA PL010 serial driver to use the clock infrastructure
to allow EP93xx platforms to properly gate the clock to the UARTs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use a pointer to struct uart_amba_port throughout the driver
rather than a mixture of that and struct uart_port.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds device ids of two Fujitsu Siemens Tablet PCs to pnp_dev_table
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sh-sci sci_br_interrupt() handler was failing to call
in to uart_handle_break(), which was something that only
the SH-3 path was doing, fix that up.
Additionally, SUPPORT_SYSRQ seems to have moved down too
far, move it back to the top so uart_handle_break() and
friends aren't no-ops.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sn console driver was snagged by the use of CONFIG_DEBUG_SHIRQ!
The request_irq() immediate call to the interrupt handler caused
another attempt to lock the port lock - deadlock.
This is a patch to fix that.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the Freescale M5282 ColdFire,
Port UA Pin Assignment Register should set to UART mode.
Patch submitted by David Wu <davidwu@arcturusnetworks.com>.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove remaining references to saved registers now that
uart_handle_sysrq_char() does not want them.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (78 commits)
[PARISC] Use symbolic last syscall in __NR_Linux_syscalls
[PARISC] Add missing statfs64 and fstatfs64 syscalls
Revert "[PARISC] Optimize TLB flush on SMP systems"
[PARISC] Compat signal fixes for 64-bit parisc
[PARISC] Reorder syscalls to match unistd.h
Revert "[PATCH] make kernel/signal.c:kill_proc_info() static"
[PARISC] fix sys_rt_sigqueueinfo
[PARISC] fix section mismatch warnings in harmony sound driver
[PARISC] do not export get_register/set_register
[PARISC] add ENTRY()/ENDPROC() and simplify assembly of HP/UX emulation code
[PARISC] convert to use CONFIG_64BIT instead of __LP64__
[PARISC] use CONFIG_64BIT instead of __LP64__
[PARISC] add ASM_EXCEPTIONTABLE_ENTRY() macro
[PARISC] more ENTRY(), ENDPROC(), END() conversions
[PARISC] fix ENTRY() and ENDPROC() for 64bit-parisc
[PARISC] Fixes /proc/cpuinfo cache output on B160L
[PARISC] implement standard ENTRY(), END() and ENDPROC()
[PARISC] kill ENTRY_SYS_CPUS
[PARISC] clean up debugging printks in smp.c
[PARISC] factor syscall_restart code out of do_signal
...
Fix conflict in include/linux/sched.h due to kill_proc_info() being made
publicly available to PARISC again.
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
[ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
[ARM] 4140/1: AACI stability add ac97 timeout and retries
[ARM] 4139/1: AACI record support
[ARM] 4138/1: AACI: multiple channel support for IRQ handling
[ARM] 4211/1: Provide a defconfig for ns9xxx
[ARM] 4210/1: base for new machine type "NetSilicon NS9360"
[ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
[ARM] 4221/1: S3C2443: DMA support
[ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
[ARM] 4219/1: S3C2443: DMA source definitions
[ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
[ARM] 4217/1: S3C24XX: remove the dma channel show at startup
[ARM] 4090/2: avoid clash between PXA and SA1111 defines
[ARM] 4216/1: add .gitignore entries for ARM specific files
[ARM] 4214/2: S3C2410: Add Armzone QT2410
[ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw
[ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
[ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
[ARM] 4137/1: Add kexec support
[ARM] 4201/1: SMP barriers pair needed for the secondary boot process
...
Fix up conflict due to typedef removal in sound/arm/aaci.h
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (34 commits)
[POWERPC] 86xx: Cleaned up platform dts files
[POWERPC] 85xx: Renamed MPC8568 MDS board code to match other boards
[POWERPC] 85xx: Cleaning up machine probing
[POWERPC] QE: clean up ucc_slow.c and ucc_fast.c
[POWERPC] 85xx: Cleaned up platform dts files
[POWERPC] 83xx: Renamed MPC8323 MDS dts and defconfig to match other boards
[POWERPC] 83xx: Updated and renamed MPC8360PB to MPC836x MDS
[POWERPC] 83xx: Use of_platform_bus_probe to setup QE devices
[POWERPC] 83xx: use default value of loops_per_jiffy
[POWERPC] 83xx: Remove obsolete setting of ROOT_DEV.
[POWERPC] 83xx: Cleaning up machine probing and board initcalls
[POWERPC] Dispose irq mapping when done in mpc52xx_serial.c
[POWERPC] 86xx: Add missing of_node_put() in mpc86xx_hpcn_init_irq().
[POWERPC] 8[56]xx: Remove obsolete setting of ROOT_DEV for 85xx and 86xx platforms.
[POWERPC] pseries: Enabling auto poweron after power is restored.
[POWERPC] use winbond libata instead of ide driver for pseries CD drives
[POWERPC] powerpc: remove references to the obsolete linux,platform property
[POWERPC] add of_get_mac_address and update fsl_soc.c to use it
[POWERPC] 83xx: Cleaned up 83xx platform dts files
[POWERPC] Fix bug with early ioremap and 64k pages
...
Fix bug that exists in kernel.org since 2.6.17rc4 - compiles fail if
CONFIG_SERIAL_CPM_SMC is defined. Tested on a board using SMC1 console.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since serial devices are powered down when not in use and some of those
devices cannot be accessed when powered down, we need to enable power
around calls to get_mcrtl() when dumping port state via uart_line_info().
This resolves hangs observed on some machines while reading serial device
registers when a port is powered off.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return failure immediately, so we don't have to test it twice.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch below works around a minor bug found in the UART of the remote
management card used in many HP ia64 and parisc servers (aka the Diva
UARTs). The problem is that the UART does not reassert the THRE interrupt
if it has been previously cleared and the IIR THRI bit is re-enabled. This
can produce a very annoying failure mode when used as a serial console,
allowing a boot/reboot to hang indefinitely until an RX interrupt kicks it
into working again (ie. an unattended reboot could stall).
To solve this problem, a backup timer is introduced that runs alongside the
standard interrupt driven mechanism. This timer wakes up periodically,
checks for a hang condition and gets characters moving again. This backup
mechanism is only enabled if the UART is detected as having this problem,
so systems without these UARTs will have no additional overhead.
This version of the patch incorporates previous comments from Pavel and
removes races in the bug detection code. The test is now done before the
irq linking to prevent races with interrupt handler clearing the THRE
interrupt. Short delays and syncs are also added to ensure the device is
able to update register state before the result is tested.
Aristeu says:
this was tested on the following HP machines and solved the problem:
rx2600, rx2620, rx1600 and rx1620s.
hpa says:
I have seen this same bug in soft UART IP from "a major vendor."
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This can be used for serial ports that are connected to an
OF platform bus but are not autodetected by the lecacy
serial support.
It will automatically take over devices that come from the
legacy serial detection, which usually is only one device.
In some cases, rtas may be set up to use the serial port
in the firmware, which allows easier debugging before probing
the serial ports. In this case, the "used-by-rtas" property
must be set by the firmware. This patch also adds code to the
legacy serial driver to check for this.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Access to chip-internal registers should always be native-endian. This is
especially important for AVR32 since it's a big-endian architecture and the
non-raw readl() and writel() macros are defined to do little-endian
accesses.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the CPCI-ASIO4 quad port CompactPCI UART board from
electronic system design gmbh.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get the Perle quad-modem PCI card (PCI-RAS4) detected by serial driver. It
may also get the PCI-RAS8 running, but can't guarantee as I didn't had one for
testing.
Signed-off-by: Thomas Hoehn <thomas.hoehn@avocent.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the serial_txx9 driver.
* Configurable manumum port number. (SERIAL_TXX9_NR_UARTS)
* Remove some code which is unneeded if CONFIG_PM=n.
* Use PCI_DEVICE() for pci device id table and make it const.
* Do not include <asm/irq.h>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SGI IOC3 and IOC4 PCI devices implement memory space apertures, not I/O
space apertures. Use the appropriate region management functions.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Stanislaw Skowronek <skylark@linux-mips.org>
Cc: Brent Casavant <bcasavan@sgi.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If RTS interrupt is caused by RTS senzing logic inside i.MX UART module the
IRQ type cannot be set.
It applies only for interrupts going through GPIO layer. The problem has
been noticed by Konstantin Kletschke some time ago.
No IRQF_TRIGGER set_type function for IRQ 26 (MPU)
I would not change type to fixed 0, because it could be possible to use
different GPIO MX1 pin for RTS in the theory. On the other hand it is only
for documentation purposes now, because RTS read code would have to be
adjusted in such case.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix occasional tx buffer overflows in the i.MX serial driver which came
from the fact that space in the buffer was checked after sending the first
byte. Also, fifosize is 32 bytes, not 8.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Atmel AT91 and AVR32 processor architectures share many of the same
peripherals. The PDC (Peripheral Data Controller) registers are also
implemented within in a number of the on-chip peripherals (eg, USART,
MMC, SPI, SSC, etc).
In a attempt not to duplicate the register definitions in each
peripheral, or in each architecture, the at91_pdc.h header in
asm-arm/arch-at91 and asm-avr32/arch-at32ap has been replaced with
linux/atmel_pdc.h.
The definitions have also been renamed from AT91_PDC_* to ATMEL_PDC_*,
and the drivers updated accordingly.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Recent update of asm-powerpc/io.h caused cpm-related stuff to break in the
current kernel. Current patch fixes it, as well as other inconsistencies
expressed, that do not permit targets from working properly:
- Updated dts with a chosen node with interrupt controller,
- fixed messed device IDs among CPM2 SoC devices,
- corrected odd header name and fixed type in defines,
- Added 82xx subdir to the powerpc/platforms Makefile, missed during
initial commit,
- new solely-powerpc header file for 8260 family (was using one from
arch/ppc, this one cleaned up from the extra stuff), in fact for now
a placeholder to get the board-specific includes for stuff not yet
capable to live with devicetree peeks only
- Fixed couple of misprints in reference mpc8272 dts.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes cpm uart able to work using OF-passed parameters
in case of CPM stuff (found on most mpc8xx reference and custom
boards). The idea is to keep ppc stuff working yet making it able to be
used for powerpc.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Using console=ttyAM1 or console=ttyAMA1 resulted in an oops during
boot due to trying to drive the console before that port had been
registered. Fix this by checking whether the port is present before
allowing console setup to proceed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes the unbalanced calls to enable_irq_wake() and
disable_irq_wake() in the AT91 (and AVR32) serial driver.
It should resolve these kernel messages:
Unbalanced IRQ x wake disable
BUG: warning at kernel/irq/manage.c:167/set_irq_wake()
Original patch from Marc Pignat.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A couple of whitespace cleanups, mainly in the AT91 header files.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
o MODPOST generates warning for i386 if compiled with CONFIG_RELOCATABLE=y
and serial console support is enabled.
o Serial console setup function, serial8250_console_setup(), is a non __init
function and it calls functions which are of type __init().
(uart_parse_options() and uart_set_options()). Assuming, setup will
be called during init time, changing serial8250_console_setup() to __init.
o Adding one more pattern to modpost whitelist. Console drivers might
have *_console structures containing references to setup functions which
can be of __init type. Don't generate warnings for those.
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'serial8250_console' (at offset 0xc05a33d8) and 'serial8250_reg'
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The mpc52xx_uart_of_enumerate() function was added when adding 52xx
support to arch/powerpc, but it must not be called for arch/ppc.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to pass in the resource otherwise we cannot
release the region properly. We must know whether it is
an I/O or MEM resource.
Spotted by Eric Brower.
Signed-off-by: David S. Miller <davem@davemloft.net>
The uartlite driver used to always enable the port even if request_port
failed causing havoc. This patch fixes it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds initial support to 8250-pci for the Korenix Jetcard PCI serial
cards. The JC12xx cards are standard RS232-based serial cards utilising
the Oxford 16C950 device.
The JC14xx are RS422/RS485-based cards, but in order for these to be
supported natively, we will need additional tweaks to the 8250 layers so
we can specify some values for the 950's registers. Hence, these two
entries are commented out.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
Fix inotify maintainers entry
Fix typo in new debug options.
Jon needs a new shift key.
fs: Convert kmalloc() + memset() to kzalloc() in fs/.
configfs.h: Remove dead macro definitions.
kconfig: Standardize "depends" -> "depends on" in Kconfig files
e100: replace kmalloc with kcalloc
um: replace kmalloc+memset with kzalloc
fix typo in net/ipv4/ip_fragment.c
include/linux/compiler.h: reject gcc 3 < gcc 3.2
Kconfig: fix spelling error in config KALLSYMS help text
Remove duplicate "have to" in comment
Fix small typo in drivers/serial/icom.c
Use consistent casing in help message
EXT{2,3,4}_FS: remove outdated part of the help text
Standardize the miniscule percentage of occurrences of "depends" in
Kconfig files to "depends on", and update kconfig-language.txt to
reflect that.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Refactor Kconfig content to maximize nesting of menus by menuconfig and
xconfig.
Tested by simultaneously running `make xconfig` with and without
patch, and comparing displays.
Signed-off-by: Don Mullis <dwm@meer.net>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the grungy swap all the occurrences in the right places patch that
goes with the updates. At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs
If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.
If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)
Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia
[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Willy pointed out the hversion is already stored
in the parisc_device, so I do not need to extract
this information directly from the IODC data.
Also by using the information in the parisc_device
I can avoid re-reading the IODC data for the Muxes
with specifed port counts.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch adds a new function to return the actual number
of ports available. Some of the built-in Muxes return the
number of supported ports, but not all of these port are
available for use.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch follows the example of the 8250_gsc
driver by probing for specific built-in Mux
cards first. This allows the system to preserve
the correct detection order with multiple Mux
cards.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The following updates are based off a patch from willy:
* Removal of the mux_card list.
* Add the mux_remove function.
Other updates:
* Re-organize the driver structure a bit to make the
mux_init and mux_exit functions more symmetrical.
* Added the del_timer.
* Unregistered the console.
At this point I can insmod, rmmod, and re-insmod the
mux without any failures.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch claims the iomem resources
for the Mux driver.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch changes the Mux console to
use the Mux hardware instead of the PDC
Software console.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (76 commits)
[ARM] 4002/1: S3C24XX: leave parent IRQs unmasked
[ARM] 4001/1: S3C24XX: shorten reboot time
[ARM] 3983/2: remove unused argument to __bug()
[ARM] 4000/1: Osiris: add third serial port in
[ARM] 3999/1: RX3715: suspend to RAM support
[ARM] 3998/1: VR1000: LED platform devices
[ARM] 3995/1: iop13xx: add iop13xx support
[ARM] 3968/1: iop13xx: add iop13xx_defconfig
[ARM] Update mach-types
[ARM] Allow gcc to optimise arm_add_memory a little more
[ARM] 3991/1: i.MX/MX1 high resolution time source
[ARM] 3990/1: i.MX/MX1 more precise PLL decode
[ARM] 3986/1: H1940: suspend to RAM support
[ARM] 3985/1: ixp4xx clocksource cleanup
[ARM] 3984/1: ixp4xx/nslu2: Fix disk LED numbering (take 2)
[ARM] 3994/1: ixp23xx: fix handling of pci master aborts
[ARM] 3981/1: sched_clock for PXA2xx
[ARM] 3980/1: extend the ARM Versatile sched_clock implementation from 32 to 63 bit
[ARM] 3979/1: extend the SA11x0 sched_clock implementation from 32 to 63 bit period
[ARM] 3978/1: macro to provide a 63-bit value from a 32-bit hardware counter
...
The pl010 primecell documentation specifies that an error indicated via RSR
should be cleared by a write to ECR. We didn't do this, which was causing
errors to be re-reported on every call to pl010_rx_chars().
Doing a write to ECR once we detect an error appears to prevent the ep93xx
console UART driver from going into a mode where it reports "ttyAM0: X
input overrun(s)" every couple of keystrokes.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add suspend/resume methods to drivers/serial/8250_pnp.c. Tested on a
P4/HT 16550A box, ttyS0 login survives across suspend to ram.
[akpm@osdl.org: cleanups]
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This a set of fixes mostly to make the driver actually work:
1. Actually select the line for setting parameters and receiver
disable/enable.
2. Select the line for receive and transmit interrupt handling correctly.
3. Report the transmitter empty state correctly.
4. Set the I/O type of ports correctly.
5. Perform polled transmission correctly.
6. Don't fix the console line at ttyS3.
7. Magic SysRq support.
8. Various small bits here and there.
Tested with a DECstation 2100 (thanks Flo for making this possible).
[akpm@osdl.org: fix typo]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass struct dev pointer to dma_cache_sync()
dma_cache_sync() is ill-designed in that it does not have a struct device
pointer argument which makes proper support for systems that consist of a
mix of coherent and non-coherent DMA devices hard. Change dma_cache_sync
to take a struct device pointer as first argument and fix all its callers
to pass it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is on our "Envoy" boxes which we have, according to the documentation, an
"Exar ST16C554/554D Quad UART with 16-byte Fifo's". The box also has two
other "on-board" serial ports and a modem chip.
The two on-board serial UARTs were being detected along with the first two
Exar UARTs. The last two Exar UARTs were not showing up and neither was the
modem.
This patch was the only way I could the kernel to see beyond the standard four
serial ports and get all four of the Exar UARTs to show up.
[akpm@osdl.org: build fix]
Signed-off-by: Paul B Schroeder <pschroeder@uplogix.com>
Cc: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a driver for the Xilinx uartlite serial controller used in boards with
the PPC405 core in the Xilinx V2P/V4 fpgas.
The hardware is very simple (baudrate/start/stopbits fixed and no break
support). See the datasheet for details:
http://www.xilinx.com/bvdocs/ipcenter/data_sheet/opb_uartlite.pdf
See http://thread.gmane.org/gmane.linux.serial/1237/ for the email thread.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (43 commits)
sh: sh775x/titan fixes for irq header changes.
sh: update r7780rp defconfig.
sh: compile fixes for header cleanup.
sh: Fixup pte_mkhuge() build failure.
sh: set KBUILD_IMAGE to something sensible.
sh: show held locks in stack trace with lockdep.
sh: platform_pata support for R7780RP
sh: stacktrace/lockdep/irqflags tracing support.
sh: Fixup movli.l/movco.l atomic ops for gcc4.
sh: dyntick infrastructure.
sh: Clock framework tidying.
sh: Turn off IRQs around get_timer_offset() calls.
sh: Get the PGD right in oops case with 64-bit PTEs.
sh: Fix store queue bitmap end.
sh: More flexible + SH7780 earlyprintk SCIF support.
sh: Fixup various PAGE_SIZE == 4096 assumptions.
sh: Fixup 4K irq stacks.
sh: dma-api channel capability extensions.
sh: Drop name overload in dma-sh.
sh: Make dma-isa depend on ISA_DMA_API.
...
Some updates for the old ColdFire serial driver:
. support 3 and 4 UARTs on some ColdFire parts that have them
. enable multifunction pins to serial for 527x CPU's
. support the 5272 UART's fractional baud rate divisor
. switch driver name to "mcfserial"
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This syncs up the SH clock framework with the linux/clk.h API,
for which there were only some minor changes required, namely
the clk_get() dev_id and subsequent callsites.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This makes the early printk support somewhat more flexible,
moving the port definition to a config option, and making the
port initialization configurable for sh-ipl+g users.
At the same time, this allows us to trivially wire up the
SH7780 SCIF0, so that's thrown in too more or less for free.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the SH7206 (SH-2A) and SH7619
(SH-2) MMU-less CPUs.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
struct pcmcia_device *p_dev->conf.ConfigBase and .Present are set in almost
all PCMICA driver right at the beginning, using the same calls but slightly
different implementations. Unfiy this in the PCMCIA core.
Includes a small bugfix ("drivers/net/pcmcia/xirc2ps_cs.c: remove unused
label") from and Signed-off-by Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As we read out the manufactor and card_id from the PCMCIA device in the
PCMCIA core, and device drivers can access those reliably in struct
pcmcia_device's fields manf_id and card_id, remove additional (and partly
broken) manf_id and card_id detection logic from PCMCIA device drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add IDs for Elan serial PCMCIA devices. In addition, move the
pdaudio_cf driver from matching based on manf_id and card_id to
the more specific prod_id1 and prod_id2 to avoid false
positives.
Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
