Patch from Lennert Buytenhek
It's silly to have I2C enabled in all ixp2000 defconfigs but not to
have the ixp2000 bus driver enabled in any of them. This patch enables
CONFIG_I2C_IXP2000 for all in-tree ixp2000 boards.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 66759a01ad introduced the fix for
time ticking too fast on some boards by disabling one of the doubly
connected timer pins on ATI boards.
However, it ends up being _much_ too broad a brush, and that just makes
some other ATI boards not work at all since they now have no timer
source.
So disable the automatic ATI southbridge detection, and just rely on
people who see this problem disabling it by hand with the option
"disable_timer_pin_1" on the kernel command line.
Maybe somebody can figure out the proper tests at a later date.
Acked-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Nicolas Pitre
This apparently fell in the crack somewhere. Add it back.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pavel Emelianov and Kirill Korotaev observe that fs and arch users of
security_vm_enough_memory tend to forget to vm_unacct_memory when a
failure occurs further down (typically in setup_arg_pages variants).
These are all users of insert_vm_struct, and that reservation will only
be unaccounted on exit if the vma is marked VM_ACCOUNT: which in some
cases it is (hidden inside VM_STACK_FLAGS) and in some cases it isn't.
So x86_64 32-bit and ppc64 vDSO ELFs have been leaking memory into
Committed_AS each time they're run. But don't add VM_ACCOUNT to them,
it's inappropriate to reserve against the very unlikely case that gdb
be used to COW a vDSO page - we ought to do something about that in
do_wp_page, but there are yet other inconsistencies to be resolved.
The safe and economical way to fix this is to let insert_vm_struct do
the security_vm_enough_memory check when it finds VM_ACCOUNT is set.
And the MIPS irix_brk has been calling security_vm_enough_memory before
calling do_brk which repeats it, doubly accounting and so also leaking.
Remove that, and all the fs and arch calls to security_vm_enough_memory:
give it a less misleading name later on.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-Off-By: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
disable_timer_pin_1 needs IO-APIC, not just local APIC.
Signed-off-by: Cal Peake <cp@absolutedigital.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from George G. Davis
As pointed out be Matthew Klahn <MKLAHN@motorola.com>, some sys_ipc()
call options require six args, e.g. SEMTIMEDOP. This patch adds an ARM sys_ipc_wrapper to save the sys_ipc() 'fifth' arg on the stack.
Signed-off-by: George G. Davis <gdavis@mvista.com>
arch/arm/kernel/calls.S | 2 +-
arch/arm/kernel/entry-common.S | 5 +++++
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Masked FPU exceptions should obviously not happen in the first place,
but if they do, ignoring them seems to be the right thing to do.
Although there is no documentation available for Cyrix MII, I did find
erratum F-7 for Winchip C6, "FPU instruction may result in spurious
exception under certain conditions" which seems to indicate that this
can happen.
That would also explain the behaviour Ondrej Zary reported on the MII.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My patch "Separate pci bits out of struct device_node" (commit
1635317fac) had the unfortunate
side-effect that it stopped eeh_init() from working correctly.
It needs the pointers set up by find_and_init_phbs(), but it was being
called just before find_and_init_phbs(). That meant that we didn't
enable EEH (pSeries PCI error recovery) on any devices, and that meant
that on POWER5 systems, the hypervisor wouldn't let us enable memory or
I/O space access to any devices, and their drivers got somewhat
confused.
This fixes it by moving the eeh_init call after find_and_init_phbs.
Tested on a POWER5 partition.
Signed-of-by: Paul Mackerras <paulus@samba.org>
Signed-of-by: Linus Torvalds <torvalds@osdl.org>
Like previously done for i386, get the x86_64 watchdog tick calculation
into a state where it can also be used on CPUs with frequencies beyond
4GHz.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the platform support code for two new Sharp Zaurus Models, Spitz
(SL-C3000) and Borzoi (SL-C3100).
This patch also adds most of the foundations for Akita (SL-C1000) Support.
The missing link for Akita is the driver for its I2C io expander. Once this
has been finished, the missing Kconfig option and machine declaration can
easily be added to this code.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate out the Sharp Zaurus c7x0 series specific code from the Corgi
backlight driver. Abstract model/machine specific functions to corgi_lcd.c
via sharpsl.h
This enables the driver to be used by the Zaurus cxx00 series.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Separate out the Sharp Zaurus c7x0 series specific code from the Corgi
Touchscreen driver. Use the new functions in corgi_lcd.c via sharpsl.h for
hsync handling and pass the IRQ as a platform device resource. Move a
function prototype into the w100fb header file where it belongs.
This enables the driver to be used by the Zaurus cxx00 series.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The same LCD is present on both the Sharp Zaurus c7x0 series and the cxx00 but
with different framebuffer drivers (w100fb vs. pxafb). This patch adds
support for the cxx00 series to the LCD driver. It also adds some LCD to
touchscreen interface logic needed by the touchscreen driver to prevent
interference problems, the idea being to keep all the ugly code in one place
leaving the drivers themselves clean. sharpsl.h is used to provide the
abstraction.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sharp's newer range of Zaurus clamshell handhelds, the cxx00's are similar to
the c7x0 series yet different. This patch series abstracts the differences
and generates a set of common drivers that support both series of devices. It
then adds machine support for Spitz (SL-C3000) and Borzoi (SL-C3100). Hooks
for Akita (SL-C1000) differences are also added. The I2C driver for its IO
expander is the only missing piece.
This patch:
Separate out the Sharp Zaurus c7x0 series specific code from corgi_ssp.c so
that other models such as the cxx00's can share it. Create sharpsl.h which
will be used to abstract machine/model specifics.
This enables the driver to be used by the Zaurus cxx00 series.
Signed-Off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the add_taint() interface for setting tainted bit flags instead of
doing it manually.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed ppc32 architecture specific users of asm/segment.h and
asm-ppc/segment.h itself
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Discard *.exit.text sections on runtime. We cannot do this on link time
because of the way BUG macros are implemented. If "__exit function" calls
one of those macros, __bug_table section will reference this function.
This is similar to ".altinstructions" situation on i386.
*.exit.data seems to be OK in this respect and is discarded on link
time.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Specialized startup code for the 68328 based DragenEngine board.
It doesn't easily fit into the common 68x328 startup code framework.
It doesn't want any of the common hardware setup to be done here.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ACPI earlyquirks needs to honor the proper config variables, and include
the right header file.
(Fixes commit 66759a01ad)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Original patch from Bertro Simul
This is probably still not quite correct, but seems to be
the best solution so far.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As mentioned before, the size of the bug frame can be further reduced while
continuing to use instructions to encode the information.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... and with that all instances in arch/x86_64 are gone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the same patch that went into i386 just before 2.6.13
came out. I still can't build 64-bit user apps, so I tested
with program (see below) in 32-bit mode on 64-bit kernel:
Before:
$ fpsig
handler: nr = 8, si = 0x0804bc90, vuc = 0x0804bd10
handler: altstack is at 0x0804b000, ebp = 0x0804bc7c
handler: si_signo = 8, si_errno = 0, si_code = 0 [unknown]
handler: fpu cwd = 0xb40, fpu swd = 0xbaa0
handler: i387 unmasked precision exception, rounded up
After:
$ fpsig
handler: nr = 8, si = 0x0804bc90, vuc = 0x0804bd10
handler: altstack is at 0x0804b000, ebp = 0x0804bc7c
handler: si_signo = 8, si_errno = 0, si_code = 6 [inexact result]
handler: fpu cwd = 0xb40, fpu swd = 0xbaa0
handler: i387 unmasked precision exception, rounded up
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The x86_64 nmi code is missing a newline in one of its messages.
I added a space before the CPU id for readability and killed the trailing
space on the previous line as well.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than blindly re-enabling interrupts in oops_end(), save their state
in oope_begin() and then restore that state.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only difference was the inline assembly, so move that into
asm/msr.h and merge with the i386 version.
This adds some missing sysfs support code to x86-64.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Being the foundation for reliable stack unwinding, this fixes CFI unwind
annotations in many low-level x86_64 routines, plus a config option
(available to all architectures, and also present in the previously sent
patch adding such annotations to i386 code) to enable them separatly
rather than only along with adding full debug information.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Report PXMs instead of nodes
- Report the correct PXM, not always the one of node 1.
- Only warn for the case of a PXM overlapping by itself
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick points out it never worked because PageReserved was
set and it might cause problems later on. Also HOTPLUG_CPU
is much more common now so let's care not too much
about the !hotplug case.
Cc: nickpiggin@yahoo.com.au
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
