The savestate command structure was being overwritten by the result of
running the TPM_SaveState command after one run, so make it a local
variable to the function instead of a global variable that gets
overwritten.
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Kent Yoder <shpedoikal@gmail.com>
Cc: Marcel Selhorst <tpm@selhorst.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the initialization of the TPM TIS driver, the necessary locality has
to be requested earlier in the init-process. Depending on the used TPM
chip, this leads to wrong information. For example: Lenovo X61s with Atmel
TPM:
tpm_tis 00:0a: 1.2 TPM (device-id 0xFFFF, rev-id 255)
But correct is:
tpm_tis 00:0c: 1.2 TPM (device-id 0x3203, rev-id 9)
This short patch fixes this issue.
Signed-off-by: Marcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we discover the TIS TPM device via PNP, use the PNP IRQ information rather
than probing for an IRQ. If PNP shows no IRQ, run the TPM in polling mode.
Tested-by: <valdis.kletnieks@vt.edu>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Kylene Hall <kjhall@us.ibm.com>
Cc: <tpm@selhorst.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the maintainers info in the tpm drivers. Kylene will be out for
some time, so copying the sourceforge list is the best way to get some
attention.
Cc: Marcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The same problem that was fixed for tpm_ascii_bios_measurements_open()
in commit 178554ae75 also occurs in
tpm_binary_bios measurements(). Thanks for noticing this Satyam!
I tested the attached patch to fix tpm_binary_bios_measurments as well.
Signed-off-by: Reiner Sailer <sailer@watson.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Coverity found a memory leak in tpm_ascii_bios_measurements_open().
If "read_log(log)" fails, then we may leak 'log' and
'log->bios_event_log'.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: Seiji Munetoh <munetoh@jp.ibm.com>
Cc: Stefan Berger <stefanb@us.ibm.com>
Cc: Reiner Sailer <sailer@watson.ibm.com>
Cc: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Kylene Hall <kjhall@us.ibm.com>
Cc: Marcel Selhorst <tpm@selhorst.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On PPC64, we need to include asm/prom.h for function definitions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The TPM driver uses two semaphores as mutexes. Use the mutex API instead of
the (binary) semaphores.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Cc: Kylene Hall <kjhall@us.ibm.com>
Cc: Marcel Selhorst <tpm@selhorst.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
flush_scheduled_work() can sleep, and we're calling it under spinlock.
AFAICS, moving flush_scheduled_work before spin_lock() should not cause any
problems.
Reason being - The only thing that can race against tpm_release is tpm_open
(tpm_release is called when last reference to the file is closed and only
thing that can happen after that is tpm_open??) and tpm_open acquires
driver_lock and more over it bails out with EBUSY if chip->num_opens is
greater than 0.
I also moved chip->num_pending-- to after deleting timer and setting data
pending as it looks more correct for the paranoid although it probably doesn't
matter as it is guarded by driver_lock. None the less this change should not
cause problems.
While I was at it I noticed a missing NULL check in tpm_register_hardware
which is fixed with this patch as well.
Signed-off-by: Parag Warudkar <parag.warudkar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tAdd adds support for devices living in MMIO space to the Infineon TPM
driver. These can be found on some of the newer HP ia64 systems.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Acked-by: Marcel Selhorst <tpm@selhorst.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These are all the remaining instances of get_property. Simple rename of
get_property to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use timer macros to set function and data members and to modify
expiration time.
- Use DEFINE_TIMER for global timers and do not init them at run-time in
these cases.
- del_timer_sync is common in most cases -- we want to wait for timer
function if it's still running.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Dmitry Torokhov <dtor@mail.ru> (Input bits)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up several code points in which the return code from misc_register is
not handled properly.
Several modules failed to deregister various hooks when misc_register fails,
and this patch cleans them up. Also there are a few modules that legitimately
don't care about the failure status of misc register. These drivers however
unilaterally call misc_deregister on module unload.
Since misc_register doesn't initialize the list_head in the init_routine if it
fails, the deregister operation is at risk for oopsing when list_del is
called. The initial solution was to manually init the list in the miscdev
structure in each of those modules, but the consensus in this thread was to
consolodate and do that universally inside misc_register.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
This also ment that some of the misc drivers had to also be fixed
up as they were assuming the device was a class_device.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- handle sysfs error
- handle driver model errors
- de-obfuscate platform_device_register_simple() call, which included an
assignment in between two function calls, in the same C statement.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
tpm_atmel changes
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix the start and len variables that should be using the new
resource_size_t.
Signed_off_by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some machine manufacturers are not sticking to the TCG specifications and
including an ACPI DSDT entry for the TPM which allows PNP discovery of the
device.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Under stress testing I found that the interrupt is not always cleared.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kfree(devname) on the misc_register() failure path. Otherwise it is lost
forever.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark the static struct file_operations in drivers/char as const. Making
them const prevents accidental bugs, and moves them to the .rodata section
so that they no longer do any false sharing; in addition with the proper
debug option they are then protected against corruption..
[akpm@osdl.org: build fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Seiji Munetoh <seiji.munetoh@gmail.com>
Change the binary output format to actual ACPI TCPA log structure since the
current format does not contain all event-data information that need to
verify the PCRs in TPM. tpm_binary_bios_measurements_show() uses
get_event_name() to convert the binary event-data to ascii format, and puts
them as binary. However, to verify the PCRs, the event-data must be a
actual binary event-data used by SHA1 calc. in BIOS.
So, I think actual ACPI TCPA log is good for this binary output format.
That way, any userland tools easily parse this data with reference to TCG
PC specification.
Signed-off-by: Seiji Munetoh <seiji.munetoh@gmail.com>
Acked-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Seiji Munetoh <seiji.munetoh@gmail.com>
Fix "tcpa_pc_event" misalignment between enum, strings and TCG PC spec and
output of the event which contains a hash data.
Signed-off-by: Seiji Munetoh <seiji.munetoh@gmail.com>
Acked-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The TPM chip on the ThinkPad T60 and Z60 machines is returning 0xFFFF for
the vendor ID which is a check the driver made to double check it was
actually talking to the memory mapped space of a TPM. This patch removes
the check since it isn't absolutely necessary and was causing device
discovery to fail on these machines.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/char/tpm/tpm.c: In function 'tpm_register_hardware':
drivers/char/tpm/tpm.c:1157: warning: assignment from incompatible pointer type
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Acked-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the constant used for the base address when it cannot be determined
from ACPI. It was off by one order of magnitude.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The TIS driver is dependent upon information from the ACPI table for device
discovery thus it compiles but does no actual work without this dependency.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently found that not all BIOS manufacturers are using the specified
generic PNP id in their TPM ACPI table entry. I have added the vendor
specific IDs that I know about and added a module parameter that a user can
specify another HID to the probe list if their device isn't being found by the
default list.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
