Misc updates from linux-omap tree, mostly to update common
device initialization and add missing defines from linux-omap
tree. Also some changes to make room for adding 34xx in
following patches.
Note that the I2C resources are now set up in
arch/arm/plat-omap/i2c.c helper, and can be removed
from devices.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch integrates the OMAP3 clock tree with the clockdomain code.
This patch:
- marks OMAP34xx clocks with their corresponding clockdomain.
- adds code to convert the clockdomain name to a clockdomain pointer in the
struct clk during clk_register().
- modifies OMAP2 clock usecounting to call into the clockdomain code
when clocks are enabled or disabled.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a new rate rounding algorithm for DPLL clocks on the
OMAP2/3 architecture.
For a desired DPLL target rate, there may be several
multiplier/divider (M, N) values which will generate a sufficiently
close rate. Lower N values result in greater power economy. However,
lower N values can cause the difference between the rounded rate and
the target rate ("rate error") to be larger than it would be with a
higher N. This can cause downstream devices to run more slowly than
they otherwise would.
This DPLL rate rounding algorithm:
- attempts to find the lowest possible N (DPLL divider) to reach the
target_rate (since, according to Richard Woodruff <r-woodruff@ti.com>,
lower N values save more power than higher N values).
- allows developers to set an upper bound on the error between the
rounded rate and the desired target rate ("rate tolerance"), so an
appropriate balance between rate fidelity and power savings can be
set. This maximum rate error tolerance is set via
omap2_set_dpll_rate_tolerance().
- never returns a rounded rate higher than the target rate.
The rate rounding algorithm caches the last rounded M, N, and rate
computation to avoid rounding the rate twice for each clk_set_rate()
call. (This patch does not yet implement set_rate for DPLLs; that
follows in a future patch.)
The algorithm trades execution speed for rate accuracy. It will find
the (M, N) set that results in the least rate error, within a
specified rate tolerance. It does this by evaluating each divider
setting - on OMAP3, this involves 128 steps. Another approach to DPLL
rate rounding would be to bail out as soon as a valid rate is found
within the rate tolerance, which would trade rate accuracy for
execution speed. Alternate implementations welcome.
This code is not yet used by the OMAP24XX DPLL clock, since it
is currently defined as a composite clock, fusing the DPLL M,N and the
M2 output divider. This patch also renames the existing OMAP24xx DPLL
programming functions to highlight that they program both the DPLL and
the DPLL's output multiplier.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a common clock framework for 24xx and 34xx.
Note that this patch does not add it to Makefile until in
next patch. Some functions are modified from earlier 24xx
clock framework code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves clock.h to clock24xx.h to make room for
adding common clock code for 24xx and 34xx.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the delayed application attribute to the dss2 clock. DSS2
can't select the 48MHz APLL with properly with out validating the
configuration as trigged by this flag.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mostly clean up CONFIG_OMAP_RESET_CLOCKS. Also includes a
patch from Imre Deak to make McSPI clocks use id.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some boards might use the oscillator clock for powering
external peripherals. Add support for making sure osc_ck
stays active even when trying to go to sleep.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch from Tony Lindgren
Update OMAP clock framework from linux-omap tree.
The highlights of the patch are:
- Add support for omap730 clocks by Andrzej Zaborowski
- Fix compile warnings by Dirk Behme
- Add support for using dev id by Tony Lindgren and Komal Shah
- Move memory timings and PRCM into separate files by Tony Lindgren
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes OMAP clock framework to use clk_enable/disable
instead of clk_use/unuse as specified in include/linux/clk.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch from Tony Lindgren
This patch adds omap24xx specific clock code by
Richard Woodruff, Nishant Menon, Tony Lindgren et al.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
