Change the setup of the PHY registers on some chip ids. These changes
make the latest sky2 driver follow the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The arch/ppc sub-tree has been removed in the powerpc git tree. The old
ibm_emac driver is no longer used by anything as a result of this. This
removes it, leaving the ibm_newemac driver as the proper driver to use for
PowerPC boards with the EMAC hardware.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The atl1 driver tries to determine the MAC address thusly:
- If an EEPROM exists, read the MAC address from EEPROM and
validate it.
- If an EEPROM doesn't exist, try to read a MAC address from
SPI flash.
- If that fails, try to read a MAC address directly from the
MAC Station Address register.
- If that fails, assign a random MAC address provided by the
kernel.
We now have a report of a system fitted with an EEPROM containing all
zeros where we expect the MAC address to be, and we currently handle
this as an error condition. Turns out, on this system the BIOS writes
a valid MAC address to the NIC's MAC Station Address register, but we
never try to read it because we return an error when we find the all-
zeros address in EEPROM.
This patch relaxes the error check and continues looking for a MAC
address even if it finds an illegal one in EEPROM.
Signed-off-by: Radu Cristescu <advantis@gmx.net>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Keep enc28j60 chips in low-power mode when they're not in use.
At typically 120 mA, these chips run hot even when idle; this
low power mode cuts that power usage by a factor of around 100.
This version provides a generic routine to poll a register until
its masked value equals some value ... e.g. bit set or cleared.
It's basically what the previous wait_phy_ready() did, but this
version is generalized to support the handshaking needed to
enter and exit low power mode.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Minor bugfixes to the enc28j60 driver ... wrong section marking,
indentation, and bogus use of spi_bus_type.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Downloading firmware in pci probe allows recovery in case of
firmware failure by reloading the driver.
Also reduced delays in firmware load.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
o Remove unnecessary debug prints and functions.
o Explicitly specify pci class (0x020000) to avoid enabling
management function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Store physical port number in netxen_adapter structure.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This fixes a the issue where logical port number is set incorrectly
for HP blade mezz cards.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ibm_newemac driver requires ether_crc to be defined. Apparently it is
possible to generate a .config without CONFIG_CRC32 set which causes the
following link errors if IBM_NEW_EMAC is selected:
LD .tmp_vmlinux1
drivers/built-in.o: In function `emac_hash_mc':
core.c:(.text+0x2f524): undefined reference to `crc32_le'
core.c:(.text+0x2f528): undefined reference to `bitrev32'
make: *** [.tmp_vmlinux1] Error 1
This patch has IBM_NEW_EMAC select CRC32 so we don't hit this error.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ROSE network is organized through nodes connected via hamradio or Internet.
AX25 packet radio frames sent to a remote ROSE address destination are routed
through these nodes.
Without the present patch, automatic routing mechanism did not work optimally
due to an improper parameter checking.
rose_get_neigh() function is called either by rose_connect() or by
rose_route_frame().
In the case of a call from rose_connect(), f0 timer is checked to find if a connection
is already pending. In that case it returns the address of the neighbour, or returns a NULL otherwise.
When called by rose_route_frame() the purpose was to route a packet AX25 frame
through an adjacent node given a destination rose address.
However, in that case, t0 timer checked does not indicate if the adjacent node
is actually connected even if the timer is not null. Thus, for each frame sent, the
function often tried to start a new connexion even if the adjacent node was already connected.
The patch adds a "new" parameter that is true when the function is called by
rose route_frame().
This instructs rose_get_neigh() to check node parameter "restarted".
If restarted is true it means that the route to the destination address is opened via a neighbour
node already connected.
If "restarted" is false the function returns a NULL.
In that case the calling function will initiate a new connection as before.
This results in a fast routing of frames, from nodes to nodes, until
destination is reached, as originaly specified by ROSE protocole.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When generating the ip header for the transformed packet we just copy
the frag_off field of the ip header from the original packet to the ip
header of the new generated packet. If we receive a packet as a chain
of fragments, all but the last of the new generated packets have the
IP_MF flag set. We have to mask the frag_off field to only keep the
IP_DF flag from the original packet. This got lost with git commit
36cf9acf93 ("[IPSEC]: Separate
inner/outer mode processing on output")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the most obvious 64-bit problems, but it is still very very
broken in other aspects.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bridge netfilter code so that it uses CONFIG_IPV6 as needed:
net/built-in.o: In function `ebt_filter_ip6':
ebt_ip6.c:(.text+0x87c37): undefined reference to `ipv6_skip_exthdr'
net/built-in.o: In function `ebt_log_packet':
ebt_log.c:(.text+0x88dee): undefined reference to `ipv6_skip_exthdr'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally, the bridge just chooses the smallest mac address as the
bridge id and mac address of bridge device. But if the administrator
has explictly set the interface address then don't change it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any frame addressed to link-local addresses should be processed by local
receive path. The earlier code would process them only if STP was enabled.
Since there are other frames like LACP for bonding, we should always
process them.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the sctp_remaddr_proc_init failed, the proper rollback is
not the sctp_remaddr_proc_exit, but the sctp_assocs_proc_exit.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The H.245 helper is not registered/unregistered, but assigned to
connections manually from the Q.931 helper. This means on unload
existing expectations and connections using the helper are not
cleaned up, leading to the following oops on module unload:
CPU 0 Unable to handle kernel paging request at virtual address c00a6828, epc == 802224dc, ra == 801d4e7c
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000000 00000004 c00a67f0
$ 4 : 802a5ad0 81657e00 00000000 00000000
$ 8 : 00000008 801461c8 00000000 80570050
$12 : 819b0280 819b04b0 00000006 00000000
$16 : 802a5a60 80000000 80b46000 80321010
$20 : 00000000 00000004 802a5ad0 00000001
$24 : 00000000 802257a8
$28 : 802a4000 802a59e8 00000004 801d4e7c
Hi : 0000000b
Lo : 00506320
epc : 802224dc ip_conntrack_help+0x38/0x74 Tainted: P
ra : 801d4e7c nf_iterate+0xbc/0x130
Status: 1000f403 KERNEL EXL IE
Cause : 00800008
BadVA : c00a6828
PrId : 00019374
Modules linked in: ip_nat_pptp ip_conntrack_pptp ath_pktlog wlan_acl wlan_wep wlan_tkip wlan_ccmp wlan_xauth ath_pci ath_dev ath_dfs ath_rate_atheros wlan ath_hal ip_nat_tftp ip_conntrack_tftp ip_nat_ftp ip_conntrack_ftp pppoe ppp_async ppp_deflate ppp_mppe pppox ppp_generic slhc
Process swapper (pid: 0, threadinfo=802a4000, task=802a6000)
Stack : 801e7d98 00000004 802a5a60 80000000 801d4e7c 801d4e7c 802a5ad0 00000004
00000000 00000000 801e7d98 00000000 00000004 802a5ad0 00000000 00000010
801e7d98 80b46000 802a5a60 80320000 80000000 801d4f8c 802a5b00 00000002
80063834 00000000 80b46000 802a5a60 801e7d98 80000000 802ba854 00000000
81a02180 80b7e260 81a021b0 819b0000 819b0000 80570056 00000000 00000001
...
Call Trace:
[<801e7d98>] ip_finish_output+0x0/0x23c
[<801d4e7c>] nf_iterate+0xbc/0x130
[<801d4e7c>] nf_iterate+0xbc/0x130
[<801e7d98>] ip_finish_output+0x0/0x23c
[<801e7d98>] ip_finish_output+0x0/0x23c
[<801d4f8c>] nf_hook_slow+0x9c/0x1a4
One way to fix this would be to split helper cleanup from the unregistration
function and invoke it for the H.245 helper, but since ctnetlink needs to be
able to find the helper for synchonization purposes, a better fix is to
register it normally and make sure its not assigned to connections during
helper lookup. The missing l3num initialization is enough for this, this
patch changes it to use AF_UNSPEC to make it more explicit though.
Reported-by: liannan <liannan@twsz.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly free h323_buffer when helper registration fails.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix three ct_extend/NAT extension related races:
- When cleaning up the extension area and removing it from the bysource hash,
the nat->ct pointer must not be set to NULL since it may still be used in
a RCU read side
- When replacing a NAT extension area in the bysource hash, the nat->ct
pointer must be assigned before performing the replacement
- When reallocating extension storage in ct_extend, the old memory must
not be freed immediately since it may still be used by a RCU read side
Possibly fixes https://bugzilla.redhat.com/show_bug.cgi?id=449315
and/or http://bugzilla.kernel.org/show_bug.cgi?id=10875
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In nr_release(), one code path calls sock_orphan() which
will NULL out sk->sk_socket already.
In the other case, handling states other than NR_STATE_{0,1,2,3},
seems to not be possible other than due to bugs. Even for an
uninitialized nr->state value, that would be zero or NR_STATE_0.
It might be wise to stick a WARN_ON() here.
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't grab the sk_callback_lock, it doesn't NULL out
the sk->sk_sleep waitqueue pointer, etc.
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't grab the sk_callback_lock, it doesn't NULL out
the sk->sk_sleep waitqueue pointer, etc.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the x25 variant of changeset
9375cb8a12
("ax25: Use sock_graft() and remove bogus sk_socket and sk_sleep init.")
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the rose variant of changeset
9375cb8a12
("ax25: Use sock_graft() and remove bogus sk_socket and sk_sleep init.")
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the netrom variant of changeset
9375cb8a12
("ax25: Use sock_graft() and remove bogus sk_socket and sk_sleep init.")
Signed-off-by: David S. Miller <davem@davemloft.net>
The way that listening sockets work in ax25 is that the packet input
code path creates new socks via ax25_make_new() and attaches them
to the incoming SKB. This SKB gets queued up into the listening
socket's receive queue.
When accept()'d the sock gets hooked up to the real parent socket.
Alternatively, if the listening socket is closed and released, any
unborn socks stuff up in the receive queue get released.
So during this time period these sockets are unreachable in any
other way, so no wakeup events nor references to their ->sk_socket
and ->sk_sleep members can occur. And even if they do, all such
paths have to make NULL checks.
So do not deceptively initialize them in ax25_make_new() to the
values in the listening socket. Leave them at NULL.
Finally, use sock_graft() in ax25_accept().
Signed-off-by: David S. Miller <davem@davemloft.net>
Three major portions to this change:
1) Add IW_EV_COMPAT_LCP_LEN, IW_EV_COMPAT_POINT_OFF,
and IW_EV_COMPAT_POINT_LEN helper defines.
2) Delete iw_stream_check_add_*(), they are unused.
3) Add iw_request_info argument to iwe_stream_add_*(), and use it to
size the event and pointer lengths correctly depending upon whether
IW_REQUEST_FLAG_COMPAT is set or not.
4) The mechanical transformations to the drivers and wireless stack
bits to get the iw_request_info passed down into the routines
modified in #3. Also, explicit references to IW_EV_LCP_LEN are
replaced with iwe_stream_lcp_len(info).
With a lot of help and bug fixes from Masakazu Mokuno.
Signed-off-by: David S. Miller <davem@davemloft.net>
Next we can kill the hacks in fs/compat_ioctl.c and also
dispatch compat ioctls down into the driver and 80211 protocol
helper layers in order to handle iw_point objects embedded in
stream replies which need to be translated.
Signed-off-by: David S. Miller <davem@davemloft.net>
