TASK_INTERRUPTIBLE and friends are now only available after including
<linux/sched.h>, so include it when needed.
bus_id is no longer available/necessary, so remove that.
Android pmem driver is not available in mainline, so remove its hooks
from drivers/video.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The config FB_PRE_INIT_FB entry in drivers/video/Kconfig pushes all entries
below it out of the menuconfig selection. Fix this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
at91sam9g45 non ES lots have an alternate pixel clock calculation formula.
Introduce this one with condition on the cpu_is_xxxxx() macros.
Newer 9g45 SOC will not have good pixel clock calculation without this
fix.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix wrong bit mask for blanking register. Due to the error a CRT monitor
blanks off due to wrong frequency (out of range) instead of PM signal
(vertical and horizontal frequencies cut off).
Just compare the mask with bits set in the switch(blank) clause below the
changed line.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove fb_save_state() and fb_restore_state operations from frame buffer layer.
They are used only in two drivers:
1. savagefb - and cause bug #11248
2. uvesafb
Usage of these operations is misunderstood in both drivers so kill these
operations, fix the bug #11248 and avoid confusion in the future.
Tested on Savage 3D/MV card and the patch fixes the bug #11248.
The frame buffer layer uses these funtions during switch between graphics
and text mode of the console, but these drivers saves state before
switching of the frame buffer (in the fb_open) and after releasing it (in
the fb_release). This defeats the purpose of these operations.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11248
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reported-by: Jochen Hein <jochen@jochen.org>
Tested-by: Jochen Hein <jochen@jochen.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix the following 'make includecheck' warning:
drivers/video/da8xx-fb.c: linux/device.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix the following 'make includecheck' warning:
drivers/video/msm/mddi.c: linux/delay.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Constify register address tables
Cc: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Cc: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes a compiler warning:
warning: assignment discards qualifiers from pointer target type
Cc: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Cc: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes a bug introduced by this commit ID:
commit 537a1bf059
Author: Krzysztof Helt <krzysztof.h1@wp.pl>
Date: Tue Jun 30 11:41:29 2009 -0700
fbdev: add mutex for fb_mmap locking
In which a mutex was added when changing smem_start and smem_len fields,
so the mutex inside the fb_mmap() call is actually used.
The problem was that set_fb_fix, which modifies the above 2 fields,
was called before and after registering the framebuffer,
which when used before registration, lead to a failed attempt to
use an uninitialized mutex.
Solution: Don't use mutex before framebuffer registration.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Imre Deak <imre.deak@nokia.com>
Tested-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (46 commits)
cnic: Fix NETDEV_UP event processing.
uvesafb/connector: Disallow unpliviged users to send netlink packets
pohmelfs/connector: Disallow unpliviged users to configure pohmelfs
dst/connector: Disallow unpliviged users to configure dst
dm/connector: Only process connector packages from privileged processes
connector: Removed the destruct_data callback since it is always kfree_skb()
connector/dm: Fixed a compilation warning
connector: Provide the sender's credentials to the callback
connector: Keep the skb in cn_callback_data
e1000e/igb/ixgbe: Don't report an error if devices don't support AER
net: Fix wrong sizeof
net: splice() from tcp to pipe should take into account O_NONBLOCK
net: Use sk_mark for routing lookup in more places
sky2: irqname based on pci address
skge: use unique IRQ name
IPv4 TCP fails to send window scale option when window scale is zero
net/ipv4/tcp.c: fix min() type mismatch warning
Kconfig: STRIP: Remove stale bits of STRIP help text
NET: mkiss: Fix typo
tg3: Remove prev_vlan_tag from struct tx_ring_info
...
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (25 commits)
drm/radeon/kms: Convert R520 to new init path and associated cleanup
drm/radeon/kms: Convert RV515 to new init path and associated cleanup
drm: fix radeon DRM warnings when !CONFIG_DEBUG_FS
drm: fix drm_fb_helper warning when !CONFIG_MAGIC_SYSRQ
drm/r600: fix memory leak introduced with 64k malloc avoidance fix.
drm/kms: make fb helper work for all drivers.
drm/radeon/r600: fix offset handling in CS parser
drm/radeon/kms/r600: fix forcing pci mode on agp cards
drm/radeon/kms: fix for the extra pages copying.
drm/radeon/kms/r600: add support for vline relocs
drm/radeon/kms: fix some bugs in vline reloc
drm/radeon/kms/r600: clamp vram to aperture size
drm/kms: protect against fb helper not being created.
drm/r600: get values from the passed in IB not the copy.
drm: create gitignore file for radeon
drm/radeon/kms: remove unneeded master create/destroy functions.
drm/kms: start adding command line interface using fb.
fb: change rules for global rules match.
drm/radeon/kms: don't require up to 64k allocations. (v2)
drm/radeon/kms: enable dac load detection by default.
...
Trivial conflicts in drivers/gpu/drm/radeon/radeon_asic.h due to adding
'->vga_set_state' function pointers.
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: new driver for ADP5520/ADP5501 MFD PMICs
backlight: extend event support to also support poll()
backlight/eeepc-laptop: Update the backlight state when we change brightness
backlight/acpi: Update the backlight state when we change brightness
backlight: Allow drivers to update the core, and generate events on changes
backlight: switch to da903x driver to dev_pm_ops
backlight: Add support for the Avionic Design Xanthos backlight device.
backlight: spi driver for LMS283GF05 LCD
backlight: move hp680-bl's probe function to .devinit.text
backlight: Add support for new Apple machines.
backlight: mbp_nvidia_bl: add support for MacBookAir 1,1
backlight: Add WM831x backlight driver
Trivial conflicts due to '#ifdef CONFIG_PM' differences in
drivers/video/backlight/da903x_bl.c
Extend the backlight event support to also allow the use of
poll()/select() on actual_brightness.
We already have the entire event hookup anyway, adding a single
function call in one line to get functionality like that is a really
good deal.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Fixes `s3c_fb_remove' referenced in section `.data' of
drivers/built-in.o: defined in discarded section `.devexit.text' of
drivers/built-in.o
With CONFIG_HOTPLUG=n, functions marked with __devexit gets removed,
so make sure we use __devexit_p when referencing pointers to them.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/video/tmiofb.c: In function 'tmiofb_resume':
drivers/video/tmiofb.c:977: warning: 'retval' may be used uninitialized in this function
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fbcon makes the (reasonable) assumption that it only needs to program the
hardware once, when fbcon_init() is called for the foreground console.
This doesn't always play well with vgacon because vgacon_deinit() is only
doing its job when the last console it owns is closed (when switching from
vgacon to fbcon, that's usually *after* fbcon_init() has set the new
mode).
Depending on the hardware this can cause the wrong framebuffer location to
be scanned out (e.g. reproduced on nv05 with the nouveau framebuffer
driver).
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Attempting to unload a framebuffer module calls unregister_framebuffer()
which in turn gets fbcon to release it. If fbcon has no framebuffers
linked to a console, it will also unbind itself from the console driver.
However, if fbcon never registered itself as a console driver, the unbind
will fail causing the framebuffer device entry to persist. In most cases
this failure will result in an oops when attempting to access the now
non-existent device.
This patch ensures that the fbcon unbind request will succeed even if a
bind was never done. It tracks if a successful bind ever occurred & will
only attempt to unbind if needed. If there never was a bind, it simply
returns with no error.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_FB_MATROX_32MB is always enabled, so there is no point in having
ifdefs all around. And it is bad practice to use CONFIG_* as a name for
something which is not a Kconfig option.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With multihead support always enabled, macros MINFO_FROM and
MINFO_FROM_INFO are no longer needed and make the code harder to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With multihead support always enabled, these macros are no longer needed
and make the code harder to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With multihead support always enabled, these macros are no longer needed
and make the code harder to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I would like to get rid of option CONFIG_FB_MATROX_MULTIHEAD and just
always enable it. There are many reasons for doing this:
* CONFIG_FB_MATROX_MULTIHEAD=y is what all x86 distributions do, so it
definitely works or we would know by now.
* Building the matroxfb driver with CONFIG_FB_MATROX_MULTIHEAD not set
results in the following build warning:
drivers/video/matrox/matroxfb_crtc2.c: In function 'matroxfb_dh_open':
drivers/video/matrox/matroxfb_crtc2.c:265: warning: the address of 'matroxfb_global_mxinfo' will always evaluate as 'true'
drivers/video/matrox/matroxfb_crtc2.c: In function 'matroxfb_dh_release':
drivers/video/matrox/matroxfb_crtc2.c:285: warning: the address of 'matroxfb_global_mxinfo' will always evaluate as 'true'
This is nothing to be worried about, the driver will work fine, but build
warnings are still annoying.
* The trick to get multihead support without CONFIG_FB_MATROX_MULTIHEAD,
which is described in the config help text, no longer works: you can't
load the same kernel module more than once.
* I fail to see how CONFIG_FB_MATROX_MULTIHEAD=y would make the code
significantly slower, contrary to what the help text says. A few extra
parameters on the stack here and there can't really slow things down in
comaprison to the rest of the code, and register access.
* The driver built without CONFIG_FB_MATROX_MULTIHEAD is larger than the
driver build with CONFIG_FB_MATROX_MULTIHEAD=y by 8%.
* One less configuration option makes things simpler. We add options
all the time, being able to remove one for once is nice. It improves
testing coverage. And I don't think the Matrox adapters are still
popular enough to warrant overdetailed configuration settings.
* We should be able to unobfuscate the driver code quite a bit after
this change (patches follow.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At the moment about half of the framebuffer drivers can return an error
code in fb_set_par. Until now it would be silently ignored by fbmem.c
and fbcon.c. This patch fixes fbmem.c to return the error code and
restore var on error.
But it is not clear in which video mode the device is when fb_set_par
fails. It would be good and reasonable if it were in the old state but
there is no guarantee that this is true for all existing drivers.
Additionally print a message if a failing fb_set_par is detected in
fbmem.c or fbcon.c.
Although most errors should be caught by the previous fb_check_var some
errors can't as they are dynamic (memory allocations, ...) and can only be
detected while performing the operations which is forbidden in
fb_check_var.
This patch shouldn't have a negative impact on normal operation as all
drivers return 0 on success. The impact in case of error depends heavily
on the driver and caller but it's expected to be better than before.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the final part of the calculation for the tft display clockrate we
divide the output pf s3c2410fb_calc_pixclk() by 2 which leaves us with a
rounding error if the result is odd.
Change to using DIV_ROUND_UP() to ensure that we always choose a higher
divisor and thus a lower frequency.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use DIV_ROUND_UP explicitly instead of manual shifts and adds. It makes
the code more readable and consistent (sometimes there were shifts,
sometimes divs).
There is no change on the assembly level (compilers should do the right
job).
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the range check for panning. The current code fails to detect some
invalid values (very high ones that can occur if an app tries to move
further up/left than 0,0) as the check uses the unknown values for
calculation so that an overflow can occur.
To fix this it is sufficient to move the calculation to the right side to
use only trusted values.
Kai Jiang detected this problem and proposed an initial patch.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Kai Jiang <b18973@freescale.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check that the result of kmalloc is not NULL before passing it to other
functions.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
when != x != NULL
when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>
[akpm@linux-foundation.org: convert to kstrdup() as well]
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It reads linetable[] before checking bounds of index, and ARRAY_SIZE is
required because linetable[] are unsigned shorts.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable 2D hardware acceleration on VX855 for copyarea, imageblit and
fillrect by selecting the correct engine which is the same as in VX800.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for a new VIA integrated graphics chipset, the VX855.
Signed-off-by: HaraldWelte <HaraldWelte@viatech.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
viafb: use read-only mode parsing
The previous method of mode parsing wrote to the strings resulting in
truncated mode strings in the sysfs.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove a structure member 'on_slot' in the chip_info structure which is
completely unused.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The main motivation of this patch was to merge the three initialization
functions in one and clean it up. However as some changes in other code
areas where needed to do it right some small other changes were made.
Changes to viafb_par:
io_virt renamed as engine_mmio and moved to shared
VQ_start renamed as vq_vram_addr and moved to shared
VQ_end removed as it is easily recalculatable
vq_vram_addr is not strictly needed but keep it to track where we
allocated video memory. The memory allocated for the virtual queue was
shrunk to VQ_SIZE as VQ_SIZE+CURSOR_SIZE looked like a bug to me. But to
be honest I don't have the faintest idea what virtual queues are for in
the graphic hardware and whether the driver needs them in any way. I only
know that they aren't directly accessed by the driver and so the only
potential current use would be as hardware internal buffers. For now keep
them to avoid regressions and only remove the double cursor allocation.
The most changes were caused by renames and the mentioned structure
changes so the chance of regressions is pretty low. The meaning of
viafb_accel changed slightly as previously it was changed back and forth
in the code and allowed to enable the hardware acceleration by software if
previously disabled. The new behaviour is that viafb_accel=0 always
prevents hardware acceleration. With viafb_accel!=0 the acceleration can
be freely choosen by set_var. This means viafb_accel is a diagnostic tool
and if someone has to use viafb_accel=0 the driver needs to be fixed.
As this is mostly a code cleanup no regressions beside the slightly change
of viafb_accel is expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split the pitch handling up and replaces the calculation from virtual xres
and bpp with fix.line_length which already contains the pitch and does not
add any constrains for the virtual resolution.
Also add a bit to the second pitch which the documentation mentions but
which was ignored by the driver.
Although it is a bit unclear what the right pitch for some LCD modes is
this patch should have no negative runtime impact.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean the hardware cursor handling up.
The most notable change is that it no longer buffers the values in
viacursor but uses the ones in cursor instead as they are guaranteed to be
always valid.
Furthermore it uses local instead global variables where possible, moves
the cursor variable in shared as only one hardware cursor is supported and
returns an error if memory allocation fails. Last but not least it fixes
a too small buffer (as u32 has only 4 and not 32 bytes) but this did not
produce any known problems.
This is mostly a code cleanup, no negative runtime changes are expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is a completly rewritten 2D engine. The engine is no longer in
a default state but reinitialized every time to allow usage for both
framebuffers regardless of their settings.
The whole engine handling is concentrated in a big function which takes 16
parameters. Although the number of parameters is worryingly it is good to
have a single funtion to deal with this stuff as it allows to easily
support different engines and avoids some code duplication.
On the way support for the new 2D engine in VX800 was added. As the with
less code duplication but it is probably better to duplicate the code as
this way is easier to walk if VIA ever decides to release a new engine
which changes anything the driver touches.
The engine support for VX800 gives a notable boost in speed. There are no
known regressions but as this patch changes paths I do neither have the
hardware nor documentation to check and has the possibility to put the
system in a critical state heavy testing is appreciated.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces viafb_shared and is the beginning of a smooth
transition to use it.
viafb_shared should contain all general, non-surface specific data that
should be shared along all viafb framebuffers while viafb_par should only
contain things that are specific to each surface or in other words extend
fb_info. This change is intended to clean the dual/multi framebuffer
handling up.
This removes the annoyance that viafbinfo1->par points to a different
structure than viaparinfo1.
As the last change is fundamental it is difficult to ensure that all parts
of the driver do not depend on the previous brokenness but the chance of
regressions is very low.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <laforge@gnumonks.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
