Several people have reported LITE-ON LTR-48246S detection failed
because SETXFER fails. It seems the device raises IRQ too early after
SETXFER. This is controller independent. The same problem has been
reported for different controllers.
So, now we have pata_via where the controller raises IRQ before it's
ready after SETXFER and a device which does similar thing. This patch
makes libata always execute SETXFER via polling. As this only happens
during EH, performance impact is nil. Setting ATA_TFLAG_POLLING is
also moved from issue hot path to ata_dev_set_xfermode() - the only
place where SETXFER can be issued.
Note that ATA_TFLAG_POLLING applies only to drivers which implement
SFF TF interface and use libata HSM. More advanced controllers ignore
the flag. This doesn't matter for this fix as SFF TF controllers are
the problematic ones.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] JAZZ ESP and SUN ESP need SPI_ATTRS
[SCSI] atari_NCR5380: update_timeout removal
[SCSI] aacraid: fix shutdown handler to also disable interrupts.
[SCSI] qla2xxx: fix timeout in qla2x00_down_timeout
[SCSI] fix CONFIG_SCSI_WAIT_SCAN=m
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: reduce raciness when input handlers disconnect
Input: ucb1x00 - do not access input_dev->private directly
Input: logips2pp - fix typo in Kconfig
Input: db9 - do not ignore dev2 module parameter
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[ICMP]: Fix icmp_errors_use_inbound_ifaddr sysctl
[IPV4]: Fix "ipOutNoRoutes" counter error for TCP and UDP
[NET] gso: Fix GSO feature mask in sk_setup_caps
[TCP]: Fix GSO ignorance of pkts_acked arg (cong.cntrl modules)
[NET]: Fix comparisons of unsigned < 0.
[NET]: Make net watchdog timers 1 sec jiffy aligned.
[ATM]: Fix warning.
[TCP]: Use default 32768-61000 outgoing port range in all cases.
[AF_UNIX]: Fix datagram connect race causing an OOPS.
[TG3]: Fix link problem on Dell's onboard 5906.
[AF_UNIX]: Make socket locking much less confusing.
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[ATA]: Don't allow to enable this for SPARC64 without PCI.
[VIDEO]: XVR500 and XVR2500 require FB=y
Fix SPI dynamic bus ID assignment to start at 2^15-1 rather than a negative
number. Valid bus ids are supposed to be positive, and are (now) stored in
an 's16' value.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a race between input handler's release() and disconnect()
methods: when input handler disconnects it wakes up all regular
users and then process to walk user list to wake up async. users.
While disconnect() walks the list release() removes elements of
the same list causing oopses.
While this is not a substibute for proper locking we can reduce
odds of getting an oops if we wake up normal readers after walking
the list.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use input_get_drvdata() and input_set_drvdata() helpers to do that.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Pavel Machek <pavel@ucw.cz>
The compiler warning
drivers/atm/firestream.c: In function ‘top_off_fp’:
drivers/atm/firestream.c:1505: warning: cast to pointer from integer of different size
does indicate a bug, albeit a minor one. Fixed, by using a 32-bit
temporary prior to the call to bus_to_virt().
The larger bug is still present: the entire driver assumes that machine
pointers are 32-bit, as it stores pointers in 32-bit hardware registers.
This is obvious to anyone who knows the driver well, but for the casual
readers it is helpfully noted with FIXME.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug is caused by code that always set
(TG3_FLAG_USE_MI_INTERRUPT | TG3_FLAG_USE_LINKCHG_REG) on all Dell's
onboard devices. With these 2 flags set, the link status is polled
by tg3_timer() and will only work when the PHY is set up to interrupt
the MAC on link changes. This breaks 5906 because the 5906 PHY does
not support TG3_FLAG_USE_MI_INTERRUPT the same as other PHYs.
For correctness, only Dell's onboard 5701 needs these 2 flags to be
set. This change will fix the 5906 problem and will change other
Dell devices except 5700 and 5701 to use the more efficient
interrupt-driven link changes.
Update version to 3.77.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix zImage.coff generation for 32-bit pmac
[POWERPC] Fix compile breakage for IBM/AMCC 4xx arch/ppc platforms
[POWERPC] Don't allow PMAC_APM_EMU for 64-bit
[POWERPC] Compare irq numbers with NO_IRQ not IRQ_NONE
[POWERPC] Fix return from pte_alloc_one() in out-of-memory case
[POWERPC] Fix compile warning in pseries xics code
[POWERPC] Don't use HOSTCFLAGS in BOOTCFLAGS
[POWERPC] Create a zImage for legacy iSeries
[POWERPC] pasemi idle uses hard_smp_processor_id
[POWERPC] ps3/interrupt.c uses get_hard_smp_processor_id
[POWERPC] Fix possible access to free pages
[POWERPC] Fix compiler/assembler flags for Ebony platform boot files
[POWERPC] Fix ppc32 single-stepping out of syscalls
[POWERPC] Update documentation for of_find_node_by_type()
NetXen: Removal of redundant free_irq
This patch removes a redundant free_irq() call from remove() routine.
This will also eliminate a warning during unload of driver.
Signed-by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The current smc91x I/O routines ifdef the solution engine subtypes
individually, which is rather bogus, as they can simply use
CONFIG_SOLUTION_ENGINE instead. This fixes it for some of the other
solution engines that weren't included in the ifdef list (SH7206
specifically).
There are also inb/outb definitions which are totally bogus (missing
brackets in _both_ cases, SMC_CAN_USE_8BIT == 0, and even better, they
try to use a 16-bit access to fake 8-bit access). Kill that nonsense off
completely.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
--
drivers/net/smc91x.h | 5 +----
1 file changed, 1 insertion(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To assure the symmetry of poll enable/disable in up/down, we should
initialize the netdevice to be poll_disabled at load time. Doing
this after register_netdevice leaves us open to another race, so
lets move all the netif_* calls above register_netdevice so the
stack starts out how we expect it to be.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Doug Chapman <doug.chapman@hp.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Many drivers had code that did kill_vid, but they weren't doing vlan
filtering. With new API the stub is unneeded unless device sets
NETIF_F_HW_VLAN_FILTER.
Bad habit: I couldn't resist fixing a couple of nearby style things
in acenic, and forcedeth.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver has unneeded stubs for VLAN filtering.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 8139cp driver did VLAN unregistration incorrectly.
It disables VLAN completely when the first VID is unregistered. It
should instead disable VLAN when the group is unregistered by calling
cp_vlan_rx_register with a NULL grp.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix sky2 disabling VLAN completely when the first vid is unregistered.
sky2 disables VLAN completely when the first VID is unregistered. It
should instead disable VLAN when the group is unregistered by calling
sky2_vlan_rx_register with grp = NULL.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
drivers/net/sky2.c | 25 +++++++++++++------------
1 file changed, 13 insertions(+), 12 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reading the code for ql_hw_csum_setup(), it is obvious that
this driver is broken for IPV6. The driver sets the NETIF_F_HW_SUM
flag, but the code for checksum setup only deals with IPV4.
Compile tested only, no hardware available.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In b302887854 I switched the apm emulation
code to use the generic code but accidentally dropped the PPC32
dependency from the configuration symbol. This adds it back.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implemented support to allow Package objects to be passed as
method arguments to the acpi_evaluate_object interface. Previously,
this would return an AE_NOT_IMPLEMENTED exception.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Last of the "Section mismatch" errors from ia64 builds! acpi_map_pxm_to_node()
is defined with attribute __cpuinit, but is called by "normal" kernel functions
acpi_getnode() and acpi_map_cpu2node().
Commit f363d16fbb moved the data structures on
which this routine operates from __cpuinitdata to regular memory, so this
routine can also move out of init space.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Moves quiesce, thread and interrupt shutdown into aacraid drivers'
.shutdown handler. This fix to the aac_shutdown handler will remove the
superfluous reset of the adapter during a (clean) kexec.
This fix may mitigate the active investigation 'kexec and aacraid
broken' but it is unlikely to affect the root cause (issue likely
present in both kexec and kdump). This patch reduces the chance the
problem will occur with a kexec. The fix for root cause is currently
expected to be the minimum value check to the aacraid.startup_timeout
driver variable after an adapter reset within aacraid_commit_reset.patch
submitted on 05/22/2007 and awaiting testing by Yinghai to confirm.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: Install firewire-constants.h and firewire-cdev.h for userspace.
firewire: Change struct fw_cdev_iso_packet to not use bitfields.
firewire: Implement suspend/resume PCI driver hooks.
firewire: add to MAINTAINERS
firewire: fw-sbp2: implement sysfs ieee1394_id
ieee1394: sbp2: offer SAM-conforming target port ID in sysfs
ieee1394: fix calculation of sysfs attribute "address"
Fix following section mismatch warning in hp100:
WARNING: drivers/net/hp100.o(.init.text+0x26a): Section mismatch: reference to .exit.text: (after 'init_module')
The warning says that we use a function marked __exit from a
function marked __init.
This is not good on architectures where we discard __exit section
for drivers that are built-in.
Note: This warning is only seen by my local copy of modpost
but the change will soon hit upstream.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following section mismatch warning in kvm-intel.o:
WARNING: o-i386/drivers/kvm/kvm-intel.o(.init.text+0xbd): Section mismatch: reference to .exit.text: (between 'hardware_setup' and 'vmx_disabled_by_bios')
The function free_kvm_area is used in the function alloc_kvm_area which
is marked __init.
The __exit area is discarded by some archs during link-time if a
module is built-in resulting in an oops.
Note: This warning is only seen by my local copy of modpost
but the change will soon hit upstream.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following section mismatch warnings in acpi
WARNING: drivers/acpi/asus_acpi.o(.init.text+0xb7): Section mismatch: reference to .exit.text: (after 'init_module')
WARNING: o-i386/drivers/acpi/toshiba_acpi.o(.init.text+0x13a): Section mismatch: reference to .exit.text: (after 'init_module')
The exit function is used in the init function during an error codition.
As __exit may be discarded during link-time / run-time this is no good.
Do not mark the exit function __exit.
Note: This warning is only seen by my local copy of modpost
but the change will soon hit upstream.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following section mismatch warnings:
WARNING: drivers/isdn/hardware/eicon/divadidd.o(.init.text+0xc4): Section mismatch: reference to .exit.text: (between 'init_module' and 'diddfunc_init')
WARNING: drivers/isdn/hardware/eicon/divas.o(.init.text+0xf4): Section mismatch: reference to .exit.text:divasfunc_exit (between 'init_module' and 'divasfunc_init')
WARNING: drivers/isdn/hardware/eicon/divas.o(.init.text+0x10d): Section mismatch: reference to .exit.text:divasfunc_exit (between 'init_module' and 'divasfunc_init')
WARNING: drivers/isdn/hardware/eicon/divas.o(.init.text+0x148): Section mismatch: reference to .exit.text:divasfunc_exit (between 'init_module' and 'divasfunc_init')
They all point to situation whare a function marked __init calls a function
marked __exit - but the __exit section may have been discarded.
Note: This warning is generated by a modified copy of modpost in my
tree. It will soon hit upstearm.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch correctly restores console state after switching from X.
Otherwise, screen is always off after switching from X.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix 2 bugs:
- SPI_DMA_RHDMA bad value.
- Missing return value in setup() function (lost passing from
patch-2.6.20-rc4-spi_imx to patch-2.6.20-rc6-spi_imx).
Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When either rx_buf or tx_buf is not being used, i.e. for plain read- or
write operations, the atmel_spi uses a fixed-size DMA buffer instead. If
the transfer is longer than the size of this buffer, it is split into
multiple DMA transfers.
When the transfer is split like this, the atmel_spi driver ends up using
the same DMA address again and again even for the buffer that came from the
user, which is of course wrong. Fix this by adding the number of bytes
already transferred to the DMA address so that the data ends up in the
right place.
Thanks to Wu Xuan for discovering this bug.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed that CLIR (aka "hide your calling number") in isdn_tty is broken:
The at-command parser filters out the required "R" (e.g. ATDR089123456)
It's been broken for a *very* long time.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Matthias Goebl <matthias.goebl@goebl.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the definitions recently posted on LKML, the maturity label
for the ISDN4Linux subsystem is wrong. This patch corrects it and also
clarifies the accompanying help text a bit.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Spotted by Satoru Takeuchi.
kill_pgrp(task_pgrp(current)) sends the signal to the current's thread
group, but can choose any sub-thread as a target for signal_wake_up().
This means that job_control() and tty_check_change() may return
-ERESTARTSYS without signal_pending().
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel Macs (and possibly other machines) provide a PNP entry for the RTC,
but provide no IRQ. As a result the rtc-cmos driver doesn't allow wakeup
alarms. If the RTC is located at the legacy ioport range, assume that it's
on IRQ 8 unless the tables say otherwise.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the forward declaration of fb_class from drivers/video/console/fbcon.h to
<linux/fb.h>, together with the other forward declarations related to
drivers/video/fbmem.c.
This kills the following sparse warning:
| drivers/video/fbmem.c:1363:14: warning: symbol 'fb_class' was not declared. Should it be static?
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because the framebuffer memory is allocated system RAM, use the sys_ drawing
libraries. It also fixes the following compile error:
LD .tmp_vmlinux1
drivers/built-in.o:(.data+0x8b48): undefined reference to `cfb_fillrect'
drivers/built-in.o:(.data+0x8b50): undefined reference to `cfb_copyarea'
drivers/built-in.o:(.data+0x8b58): undefined reference to `cfb_imageblit'
[adaplas]
Use fb_sys_read/write for the same reasons as above.
Signed-off-by: Avuton Olrich <avuton@gmail.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes wrong ifdef around the xxxfb_setup. It also moves this
function to remove forward declaration.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix various bits of obviously-busted code which we're not happening to
compile, due to ifdefs.
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Jan Kara <jack@ucw.cz>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have made a tool to parse the kernel that does not pre-process the
source. That means that my parser tries to parse all the code, including
code in the #else branch or code that is not often compiled because the
driver is not very used (or not used at all). So, my parser sometimes
reports parse error not originally detected by gcc. Here is my (first)
patch.
[akpm@linux-foundation.org: fix amd8111e.c]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: James Bottomley <James.Bottomley@steeleye.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"Mike Miller (OS Dev)" <mikem@beardog.cca.cpqcorp.net> writes:
Found what seems the problem with our vectors being listed backward. In
drivers/pci/msi.c we should be using list_add_tail rather than list_add to
preserve the ordering across various kernels. Please consider this for
inclusion.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Screwed-up-by: Michael Ellerman <michael@ellerman.id.au>
Cc: "Mike Miller (OS Dev)" <mikem@beardog.cca.cpqcorp.net>
Cc: Andi Kleen <ak@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ucc_geth has been migrated to use the common phylib code. So lets add a
'select PHYLIB' to the UCC_GETH Kconfig entry.
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Via VT3351 APIC does not play well with MSI and unleashes a flood
of APIC errors when MSI is used to deliver interrupts. The problem
was recently exposed when the atl1 network device driver, which enables
MSI by default, stimulated APIC errors on an Asus M2V mainboard, which
employs the Via VT3351.
See http://bugzilla.kernel.org/show_bug.cgi?id=8472 for additional
details on this bug.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_find_present() is only matching the last item in the list of ids.
The break after the match is found only escapes the for loop, not the
while loop, so found gets reset to NULL on the next pass.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've been seeing lots of messages like these:
eth0: No interrupt was generated using MSI, switching to INTx mode. Please
report this failure to the PCI maintainer and include system chipset
information.
On several systems that use the following Severworks HT1000 (also sometimes
labeled as a Broadcom chipset as well) bridge chips. It doesn't appear MSI
works well (if at all) on these systems.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In file included from drivers/pci/msi.c:22:
include/asm/smp.h:17:26: asm/arch/smp.h: No such file or directory
include/asm/smp.h:20:3: #error "<asm-arm/smp.h> included in non-SMP build"
include/asm/smp.h:23:1: warning: "raw_smp_processor_id" redefined
In file included from include/linux/sched.h:65,
from include/linux/mm.h:4,
from drivers/pci/msi.c:10:
include/linux/smp.h:85:1: warning: this is the location of the previous
definition
Tested on powerpc, i386, and x86_64.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The struct is part of the userspace interface and can not use
bitfields. This patch replaces the bitfields with a __u32 'control'
word and provides access macros to set the bits.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
It's a low-impact design, that just makes suspend/resume look like
a bus reset to the upper level drivers, but it should be sufficient.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The attribute /sys/bus/scsi/devices/*:*:*:*/ieee1394_id, as generated by
the old sbp2 driver, is typically used to create persistently named
links in /dev/disk/by-id.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
With "modprobe sbp2 long_ieee1394_id=y", the format of
/sys/bus/scsi/devices/*:*:*:*/ieee1394_id is changed from e.g.
0001041010004beb:0:0 to 0001041010004beb:00042c:0000.
The longer format fully conforms to object identifier sizes as per
SAM(-2...4) and reflects what the SAM target port identifier is meant to
contain: A Discovery ID allegedly specified by ISO/IEC 13213:1994 ---
however there is no such thing; the authors of SAM probably meant
Directory ID). Especially target nodes with multiple dynamically added
targets may use Directory IDs to persistently identify target ports.
The new format is independent of implementation details of nodemgr.
Thus the same ieee1394_id attribute format can be implemented in the new
firewire stack.
The ieee1394_id is typically used to create persistently named links in
/dev/disk/by-id.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The initial version of the thinkpad-acpi sysfs interface (not yet released
in any stable mainline kernel) made liberal use of named sysfs groups, in
order to get the attributes more organized.
This proved to be a really bad design decision. Maybe if attribute groups
were as flexible as a real directory, and if binary attributes were not
second-class citizens, the idea of subdirs and named groups would not have
been so bad.
This patch makes all the thinkpad-acpi sysfs groups anonymous (thus
removing the subdirs), adds the former group names as a prefix (so that
hotkey/enable becomes hotkey_enable for example), and updates the
documentation.
These changes will make the thinkpad-acpi sysfs ABI a lot easier to
maintain.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] cio: deregister ccw device when pgid disband failed
[S390] cio: Use device_schedule_callback() for removing disconnected devices.
[S390] Fix section annotations.
[S390] raw3270: use mutex instead of semaphore
[S390] arch/s390/kernel/debug.c: use mutex instead of semaphore
[S390] dasd_eer: use mutex instead of semaphore
[S390] Add exception handler for diagnose 224
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
[IPSEC]: Add xfrm_sysctl.txt.
[BRIDGE]: Round off STP perodic timers.
[BRIDGE]: Reduce frequency of forwarding cleanup timer in bridge.
[TCP] tcp_probe: use GCC printf attribute
[TCP] tcp_probe: a trivial fix for mismatched number of printl arguments.
[IPV6] ADDRCONF: Fix conflicts in DEVCONF_xxx constant.
[NET] napi: Call __netif_rx_complete in netif_rx_complete
[TCP]: Consolidate checking for tcp orphan count being too big.
[SOCK]: Shrink struct sock by 8 bytes on 64-bit.
[AF_PACKET]: Kill CONFIG_PACKET_SOCKET.
[IPV6]: Fix build warning.
[AF_PACKET]: Kill bogus CONFIG_PACKET_MULTICAST
[IPV4]: Kill references to bogus non-existent CONFIG_IP_NOSIOCRT
[IPSEC]: Fix panic when using inter address familiy IPsec on loopback.
[NET]: parse ip:port strings correctly in in4_pton
[IPV6] ROUTE: No longer handle ::/0 specially.
[IPSEC]: Fix IPv6 AH calculation in outbound
[XFRM]: xfrm_larval_drop sysctl should be __read_mostly.
[XFRM]: Allow XFRM_ACQ_EXPIRES to be tunable via sysctl.
[CASSINI]: Fix printk message typo.
...
Deregister ccw device when device failure is detected during offline-
processing (e.g. when no last-path-gone indication was presented by
the hardware) to prevent the device from entering a non-recoverable
not-operational state.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We can't deregister disconnected and orphaned devices directly from
the online attribute's store method, but must take a detour.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit c0affe9db4 doesn't work because
the host controller is being quirked not a PCI bridge. This patch
reverts the commit, rename quirk_svw_msi() to quirk_disable_all_msi()
and use it instead.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Matias Alejandro Torres <torresmat@gmail.com>
Cc: Greg K-H <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix enable_irq_wake and disable_irq_wake symmetry in at91 pcmcia driver
disable_irq_wake call must be symmetric with enable_irq_wake. This patch
fix that problem for the at91_pcmia driver. It seems that this patch was
forgotten when we've fixed irq_wake symmetry in all at91 related drivers.
It was discussed in the "at91 drivers and [enable/disable]_irq_wake
(wrong?) usage" thread on the linux-arm-kernel mailing list.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pseudo_palette has room for 16 entries only, but in truecolor mode, it
attempts to write 256.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Acked-by: Tero Roponen <teanropo@jyu.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/sbus/char/flash.c does use macros VM_READ and such, needs to include
linux/mm.h.
Signed-off-by: Horst H. von Brand <vonbrand@inf.utfsm.cl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
iterations is unsigned, so it is impossible to get out of the loop
and return -ETIMEDOUT.
Signed-off-by: Bill Nottingham <notting@redhat.com>
Acked-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
CONFIG_MODULES=y
CONFIG_SCSI=y
CONFIG_SCSI_SCAN_ASYNC=y
CONFIG_SCSI_WAIT_SCAN=m
2.6.21-rc5-mm2 VFS panics unable to find my root on /dev/sda2, but boots
okay if I change drivers/scsi/Kconfig to "default y" instead of "default m"
for SCSI_WAIT_SCAN.
Make sure there's a late_initcall to scsi_complete_async_scans when it's
built in, so a monolithic SCSI_SCAN_ASYNC kernel can rely on the scans
being completed before trying to mount root, even if they're slow.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Must access the respective queue's dummy netdev instead of the port's netdev.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't want IRQ on FIFO error because there is nothing useful to do with it.
But do want IRQ on duplex change.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This restores the previously removed netif_poll_enable call in e1000_open.
It's needed on all but the first call to e1000_open for a NIC as
e1000_close always calls netif_poll_disable.
netif_poll_enable can only be called safely if no polls have been
scheduled. This should be the case as long as we don't enter our IRQ
handler.
In order to guarantee this we explicitly disable IRQs as early as possible
when we're probing the NIC.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "Kok, Auke" <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If ioremap_nocache() is unfortunate enough to fail, the error code is not
set correctly leading to a false success from dfx_register(). This change
fixes the problem.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver was reading value from one register, setting bit and then
writing the wrong register.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver was not correctly setting up transmit descriptor when doing
VLAN tag insertion with checksum offload.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This code inherited from the sk98lin driver is incorrect on the Yukon2.
The GPHY_CTRL register values are specific to the internal PHY of the chip
and the values used were leftovers.
Driver was setting bit 13 which is now the INT polarity for the PHY!
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The -rt patch triggered a lockdep warning in the amba serial drivers, which never
shows up on UP kernels. On SMP systems this would trigger as well.
Release the port lock before calling tty_flip_buffer_push() and reacquire it after
the call. This matches the code in the 8250 serial driver.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix a error reported by newer versions of GCC.
error: static declaration of 'ks8695_reg' follows non-static declaration
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add __init to:
acpi_initialize_subsystem() (and un-export it)
acpi_os_initialize()
Add __initdata to:
acpi_osl_dmi_table[]
Signed-off-by: Len Brown <len.brown@intel.com>
_OSI("Linux") is like _OS("Linux"), it is ill-defined and
virtually no BIOS vendors test interaction with it.
As a result, it can do more damage than good because
it causes the BIOS to follow un-tested paths.
Recently, several machines have turned up that erroneously
test this string in a way which causes them to _not_ test other
compatibility strings, including the ZI9 and Toshiba.
So it appears that this bad code has made it into
a BIOS vendor's reference BIOS.
Linux has no choice but to stop advertising compatibility
with _OSI string "Linux" - as there are an unbounded
number of possible incompatibilities going forward.
But some BIOSes have already shipped which do use it
for things like conditionally re-enabling video on resume
from S3. (Too bad they didn't do that unconditionally)
Add special case code for _OSI(Linux)
Squawk to dmesg if _OSI(Linux) is requested
Add DMI list both to enable and disable _OSI(Linux)
But for now, keep the default enabled via
#define OSI_LINUX_ENABLED.
http://bugzilla.kernel.org/show_bug.cgi?id=7787
Signed-off-by: Len Brown <len.brown@intel.com>
Add data from zero-entropy random_writes directly to output pools to
avoid accounting difficulties on machines without entropy sources.
Tested on lguest with all entropy sources disabled.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set last allocated object to the object after the one just allocated
before ORing in the extra top bits. Also handle the case where this
wraps around.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ib_cm can incorrectly detect a stale connection (a new connection
request for a QPN that is already connected) as a duplicate connection
request. Separate the handling of potential duplicate REQs from stale
connections.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
commit 518b1646 ("IPoIB/cm: Fix SRQ WR leak") introduced a severe
performance regression on Mellanox cards, because keeping a QP in the
error state for extended periods of time moves hardware to the slow
path (until the QP is destroyed). For example, MPI latency goes from
~3 usecs to ~7 usecs.
Fix this by posting a send WR on one of the QPs that are being
flushed, instead of using a separate drain QP that is kept in the
error state.
This fixes bug <https://bugs.openfabrics.org/show_bug.cgi?id=636>,
reported and bisected by Scott Weitzenkamp at Cisco and debugged by
Sasha Mikheev at Voltaire.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_free_err_wqe() currently treats both send and receive CQEs
identically if a QP is using an SRQ. But for Tavor hardware, send
CQEs with error can be chained together even if the RQ is part of SRQ,
so we may miss some CQEs.
Fix by following the WQE chain for all send CQEs even for non-SRQ QPs.
This fixes crashes in IPoIB CM:
<https://bugs.openfabrics.org//show_bug.cgi?id=604>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The boot option "acpi_osi=" has always disabled Linux _OSI support,
thus disabling all OS Interface strings which are advertised
by Linux to the BIOS.
Now...
acpi_osi="string" adds the interface string, and
acpi_osi="!string" invalidates the pre-defined interface string
eg. acpi_osi="!Windows 2006"
would disable Linux's claim of Vista compatibility.
Signed-off-by: Len Brown <len.brown@intel.com>
For users with active thermal trip points, they need
the fan's name, rather than its address, to understand
where to look to observe and control fan state.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
HP and Hitachi machines have been implemented with SSDT's
that use the "OEMx" signatures. But upon Load, ACPICA is rejecting
these tables because they are not using the "SSDT" signature.
ACPI Error (tbinstal-0134): Table has invalid signature [OEMx], must be SSDT...
Signed-off-by: Len Brown <len.brown@intel.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fill holes in hypervisor APIs and fix KTSB registry.
[SPARC64]: Fix two bugs wrt. kernel 4MB TSB.
[SPARC]: Mark as emulating cmpxchg, add appropriate depends for DRM.
[SPARC]: Emulate cmpxchg like parisc
[SPARC64]: Fix _PAGE_EXEC_4U check in sun4u I-TLB miss handler.
[SPARC]: Linux always started with 9600 8N1
[SPARC64]: arch/sparc64/time.c doesn't compile on Ultra 1 (no PCI)
[SPARC64]: Eliminate NR_CPUS limitations.
[SPARC64]: Use machine description and OBP properly for cpu probing.
[SPARC64]: Negotiate hypervisor API for PCI services.
[SPARC64]: Report proper system soft state to the hypervisor.
[SPARC64]: Fix typo in sun4v_hvapi_register error handling.
[SCSI] ESP: Kill SCSI_ESP_CORE and link directly just like jazz_esp
[SCSI] jazz_esp: Converted to use esp_core.
[SPARC64]: PCI device scan is way too verbose by default.
[SERIAL] sunzilog: section mismatch fix
[SPARC32]: Removes mismatch section warnigs in sparc time.c file
[SPARC64]: Don't be picky about virtual-dma values on sun4v.
[SPARC64]: Kill unused DIE_PAGE_FAULT enum value.
[SCSI] pluto: Use wait_for_completion_timeout.
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon/applesmc: Handle name file creation error and deletion
hwmon/applesmc: Simplify dependencies
hwmon-vid: Don't spam the logs when VRM version is missing
hwmon/w83627hf: Be quiet when no chip is found
hwmon/coretemp: Add more safety checks
hwmon/ds1621: Fix swapped temperature limits
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] megaraid_sas: intercept cmd timeout and throttle io
[SCSI] fusion: Fix |/|| confusion
[SCSI] aic94xx: asd_clear_nexus should fail if the cleared task does not complete
[SCSI] aic7xxx: fix aicasm build failure with gcc-3.4.6
[SCSI] aacraid: apply commit config for reset_devices flag
[SCSI] sd: fix refcounting regression in suspend/resume routines
[SCSI] aacraid: fix panic on short Inquiry
[SCSI] aacraid: Correct sa platform support. (Was: [Bug 8469] Bad EIP value on pentium3 SMP kernel-2.6.21.1)
[SCSI] NCR53C9x: correct spelling mistake in deprecation notice
[SCSI] tgt: fix a rdma indirect transfer error bug
[SCSI] MegaRAID: Update MAINTAINERS email-id
[SCSI] stex: minor cleanup and version update
[SCSI] stex: fix reset recovery for console device
[SCSI] stex: extend hard reset wait time
[SCSI] stex: fix id mapping issue
[SCSI] ipr: Proper return codes for eh_dev_reset for SATA devices
[SCSI] zfcp: IO stall after deleting and path checker changes after reenabling zfcp devices
[SCSI] zfcp: avoid clutter in erp_dbf
This patch (as912) replaces a couple of calls to flush_workqueue()
with cancel_sync_work() and cancel_rearming_delayed_work(). Using a
more directed approach allows us to avoid some nasty deadlocks. The
prime example occurs when a first-level device (the parent is a root
hub) is removed while at the same time the root hub gets a remote
wakeup request. khubd would try to flush the autosuspend workqueue
while holding the root-hub's lock, and the remote-wakeup workqueue
routine would be waiting to lock the root hub.
The patch also reorganizes the power management portion of
usb_disconnect(), separating it out into its own routine. The
autosuspend workqueue entry is cancelled immediately instead of
waiting for the device's release routine. In addition,
synchronization with the autosuspend thread is carried out even for
root hubs (an oversight in the original code).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <gregkh@suse.de>
Cc: Mark Lord <lkml@rtr.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When hostap_tx_encrypt() tries to allocate enough headroom and
tailroom for ieee80211 encryption, it only makes enough room for the
"mpdu" phase of the operation, but forgets about the "msdu" phase.
(For TKIP, these two phases require, respectively, 4 and 8 bytes of
tailroom, per the "ieee80211_crypt_tkip" structure at the bottom of
net/ieee80211/ieee80211_crypt_tkip.c.)
Signed-off-by: Brandon Craig Rhodes <brandon@rhodesmill.org>
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Manually set the device of a skb for prism54 cards that are in monitor
mode as we never call eth_type_trans in that case.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The DRM code depends on an atomic version of cmpxchg(), which is not
available on sparc32. Since other platforms besides sparc32 have this
issue a KCONFIG option is added for it.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel ignored the PROM's serial settings (115200,n,8,1 in
my case). This was because mode_prop remained "ttyX-mode" (expected:
"ttya-mode") due to the constness of string literals when used with
"char *". Since there is no "ttyX-mode" property in the PROM, Linux
always used the default 9600.
[ Investigation of the suncore.s assembler reveals that gcc optimizied
away the stores, yet did not emit a warning, which is a pretty
anti-social thing to do and is the only reason this bug lived for
so long -DaveM ]
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new esp_scsi for JAZZ SCSI host adapter driver
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes section mismatch warnings in the sunzilog driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of incorrect parameter setup anything passed in dev2=...
was always ignored by the driver. See bugzilla #8541.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix this warning on x86-64
drivers/firewire/fw-cdev.c:798: warning: initialization from incompatible pointer type
by making the return code of ioctl_send_request() the same as all the
other ioctl_xxx() return codes.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Of course everybody immediately associates "fw-" with FireWire, not
firmware or firewall or whatever. But "firewire-" has a nice ring to
it too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Hoegsberg <krh@bitplanet.net>
While playing with libiec61883 I've noticed that async_send is broken
because it was doing copy_from_user(...., packet->data_size) before
packet->data_size was set to any useful value. It got broken when
packet->allocated_data_size got introduced, as hpsb_alloc_packet does
not set packet->data_size anymore. (Regression in 2.6.22-rc1)
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This adds a real parent device to eth1394's ethX device like in Linux
2.6.20 and older. However, due to unfinished conversion of the ieee1394
away from class_device, we now refer to the FireWire controller's PCI
device as the parent, not to the ieee1394 driver's fw-host device.
Having a real parent device instead of a virtual one allows udev scripts
to distinguish eth1394 interfaces from networking bridges, bondings and
the likes.
Fixes a regression since 2.6.21:
https://bugs.gentoo.org/show_bug.cgi?id=177199
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
When eth1394 was unable to acquire a transaction label, it just dropped
outgoing packets without attempt to resend them later.
The transmit queue is now halted if no tlabel is available to
->hard_start_xmit(). A workqueue job is then scheduled to catch the
moment when ieee1394 recycled the next lot of tlabels.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=8402
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If we cannot guess which VRM version the CPU uses, we set it to 0 and
log it. So we shouldn't spam the log each time vid_from_reg() is
later called with vrm 0.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
Add detection of AE18 Errata of Core processor and warns
users that the absolute readings might be wrong for Core2 processor.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The low temperature limit and the high temperature limit registers
have been accidentally swapped, causing alarms to trigger
when they shouldn't.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Using lockdep validator causes warnings like
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
[<c00241a0>] (dump_stack+0x0/0x14) from [<c00520f8>] (__lock_acquire+0x150/0xc40)
[<c0051fa8>] (__lock_acquire+0x0/0xc40) from [<c00530a0>] (lock_acquire+0x5c/0x70)
[<c0053044>] (lock_acquire+0x0/0x70) from [<c01d9e44>] (_spin_lock_irq+0x48/0x58)
r7:c07e5144 r6:00000000 r5:c015fb94 r4:c07e50b8
[<c01d9dfc>] (_spin_lock_irq+0x0/0x58) from [<c015fb94>] (i2c_pxa_xfer+0x110/0x2e0)
r5:c07e50b8 r4:0000001f
This is caused by memcpy'ing a statical initialized spin-lock. This patch
removes a static pxa_i2c structure which was used only as a source for this
memcpy() operation. Instead of, members and the spinlock will be
initialized manually.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB/cm: Drain cq in ipoib_cm_dev_stop()
IPoIB/cm: Fix timeout check in ipoib_cm_dev_stop()
IB/ehca: Fix number of send WRs reported for new QP
IB/mlx4: Initialize send queue entry ownership bits
IB/mlx4: Don't allocate RQ doorbell if using SRQ
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Supplied by VIA.
Also, convert named constants to hex values in the pata_via
PCI ID table. (standard libata policy for PCI device IDs, which are
considered simply arbitrary hex numbers, without a need to create a
single-use constant in linux/pci_ids.h)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sata_sis driver supports SATA and PATA ports. The broken support
of both types in one controller is fixed.
Signed-off-by: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The commit d4b2bab4f2 added deadline support
to prereset and reset methods to libbata the pata_scc driver wasn't
converted. This patch is a naive attempt to bring this driver up to
scratch.
Build failures are:
drivers/ata/pata_scc.c: In function 'scc_pata_prereset':
drivers/ata/pata_scc.c:870: error: too few arguments to function 'ata_std_prereset'
drivers/ata/pata_scc.c: In function 'scc_error_handler':
drivers/ata/pata_scc.c:916: warning: passing argument 2 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c:916: warning: passing argument 3 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c: In function 'scc_pata_prereset':
drivers/ata/pata_scc.c:871: warning: control reaches end of non-void function
On a releated note scc_bus_post_reset() is (AFACT) identical to
ata_bus_post_reset(), would a patch to make ata_bus_post_reset() assesable
to drivers be accepted?
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_via: Handle laptops via DMI
libata: -ENODEV during prereset isn't an error
libata: don't consider 0xff as port empty if SStatus is available
ata_piix: add short 40c quirk for Acer Aspire 2030, take #2
pata_sis: Fix and clean up some timing setups
hpt3x2n: Correct revision boundary
Oh the joy of saving a fraction of a cent using short 40 wire cables and
not faking 80wire
Teach the VIA driver that there are some systems we need to know are
magically wired for high speeds.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Francis Russell <FrancisRussell@btinternet.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
During prereset, -ENODEV return from ata_wait_ready() is not an error.
This causes unnecessary bug message on controllers which uses 0xff to
indicate empty port. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some SATA controllers (sata_sil) use 0xff to indicate port not ready
status, not port empty. As libata interprets 0xff as port empty, this
causes unnecessary reset failure and retry. Don't consider 0xff as
port empty if SStatus is available and indicates that port is online.
Signed-off-by: tejun Heo <htejun@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Indan Zupancic <indan@nul.nu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acer Aspire 2023WLMi uses short 40c cable. Add quirk for it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Steve H. <mail.pandor@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Rename sis_port_base to sis_old_port_base() so nobody uses it for new
generation controllers in error.
- Use byte size operations where it is cleaner for mode setup
- Fix a couple of masking errors on certai chip revs when setting speeds
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We have a revision that isn't correctly claimed as two drivers both go
for it: Fix the test accordingly. Noticed originally by Bill Nottingham.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at
once instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use menuconfigs instead of menus, so the whole menu can be disabled at
once instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use mutex instead of binary semaphore in idt77252 driver.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the cpu irq mask define to include the timer irq.
Another flag check was setting up the timer bit in all cases so we
didn't notice the issue.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The stats update code in spider_net_pass_skb_up() is touching the skb
after it's been passed up to the stack. To avoid that, just update the
stats first.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The meth ethernet driver for the SGI IP32 aka O2 is so far still an old
style driver which does not use the device driver model. This is now
causing issues with some udev based gadgetry in debian-stable. Fixed by
converting the meth driver to a platform device.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
--
Fixes since previous patch:
o Fixed typo in meth_exit_module()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
This patch has removed unnecessary dependency on VIA velocity config.
Yoichi
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct the following compiler warning (and warnings resulting from
the correction):
warning: 'fixed_mdio_register_device' defined but not used
Signed-off-by: Denver Gingerich <denver@ossguy.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(Originally sent to linux-usb-devel)
The attached patch adds the device IDs for the Belkin F5D5055 device.
Reported by Andy Juniper <ajuniper@freeuk.com>
Signed-off-by: David Hollis <dhollis@davehollis.com>
--
David Hollis <dhollis@davehollis.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix MODULE_DEVICE_TABLE() duplication in ucc_geth.c and ucc_geth_mii.c
for ucc_geth to be compiled as module.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since NAPI polling is disabled while ipoib_cm_dev_stop() is running,
ipoib_cm_dev_stop() must poll the CQ itself in order to see the
packets draining.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
time_after() was used backwards, so the timeout occurred immediately.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Due to a typo, the driver was reporting the wrong number of "actual send
WRs" after ehca_create_qp().
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need to initialize the owner bit of send queue WQEs to hardware
ownership whenever the QP is modified from reset to init, not just
when the QP is first allocated. This avoids having the hardware
process stale WQEs when the QP is moved to reset but not destroyed and
then modified to init again.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: add maintainer for ARM Primecell controller
mmc: add maintainer for iMX MMC interface
mmc: Add maintainers for TI OMAP MMC interface
mmc: mark unmaintained drivers
mmc: clean up unused parts of block driver
eh_timed_out call back (megasas_reset_timer) is used to throttle io
to the adapter when it is called the first time for a scmd.
The MEGASAS_FW_BUSY flag is set and can_queue reduced to 16.
The can_queue is restored from completion routine in following
two conditions : 5 seconds has elapsed and
the # of outstanding cmds in FW is < 17.
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In case of Broadcom based Bluetooth devices, it is safe to always
send HCI_Reset as first command. This gives the advantage that
all HID Proxy versions will automatically work and don't need any
additional quirks anymore.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Allow in-place crypto operations. Also remove the coherent user flag
(we use it automagically now), and by default use the user written
key rather then the HW hidden key - this makes crypto just work without
any special considerations, and thats OK, since its our only usage
model.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Squash these:
drivers/isdn/hardware/eicon/message.c: In function 'api_put':
drivers/isdn/hardware/eicon/message.c:536: warning: cast from pointer to integer of different size
drivers/isdn/hardware/eicon/message.c: In function 'plci_free_msg_in_queue':
drivers/isdn/hardware/eicon/message.c:1035: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/message.c: In function 'data_b3_req':
drivers/isdn/hardware/eicon/message.c:3121: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/message.c:3154: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/message.c: In function 'callback':
drivers/isdn/hardware/eicon/message.c:4060: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/message.c: In function 'nl_ind':
drivers/isdn/hardware/eicon/message.c:7137: warning: cast from pointer to integer of different size
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
squish these:
drivers/isdn/hardware/eicon/capifunc.c: In function 'TransmitBufferSet':
drivers/isdn/hardware/eicon/capifunc.c:192: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/capifunc.c: In function 'TransmitBufferGet':
drivers/isdn/hardware/eicon/capifunc.c:197: warning: cast from pointer to integer of different size
drivers/isdn/hardware/eicon/capifunc.c:198: warning: cast from pointer to integer of different size
drivers/isdn/hardware/eicon/capifunc.c:200: warning: cast from pointer to integer of different size
drivers/isdn/hardware/eicon/capifunc.c: In function 'TransmitBufferFree':
drivers/isdn/hardware/eicon/capifunc.c:205: warning: cast from pointer to integer of different size
drivers/isdn/hardware/eicon/capifunc.c:206: warning: cast from pointer to integer of different size
drivers/isdn/hardware/eicon/capifunc.c: In function 'sendf':
drivers/isdn/hardware/eicon/capifunc.c:304: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/capifunc.c:304: warning: cast to pointer from integer of different size
drivers/isdn/hardware/eicon/capifunc.c:321: warning: cast to pointer from integer of different size
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The omap_uwire controller driver handles SPI_CPHA incorrectly;
It should mean:
CPHA=0 ... sample at leading edge of clock
CPHA=1 ... sample at trailing edge of clock
This bug has been masked by inverse bugs in layered drivers;
and was uncovered by running some of them on non-OMAP hardware.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=7482.
It sets USB snooping on 4G space for PowerPC platforms without
CONFIG_NOT_COHERENT_CACHE defined.
Reported-by: Stefan Meyer <reyems@telkomsa.net>
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Another coverity patch i forgot to resend, original thread here
http://marc.info/?l=linux-kernel&m=115144559823592&w=2
In case drive == N_DRIVE, we get one past the drive_params array.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as875) adds error-checking to the callers of hisax_register().
It also changes an error pathway in that routine, making it return an error
code rather than 0.
This fixes Bugzilla #7960.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Karsten Keil <kkeil@suse.de>
Cc: Martin Bachem <info@colognechip.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adding a drive to a linear array seems to have stopped working, due to changes
elsewhere in md, and insufficient ongoing testing...
So the patch to make linear hot-add work in the first place introduced a
subtle bug elsewhere that interracts poorly with older version of mdadm.
This fixes it all up.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is possible that real data or metadata follows the bitmap without full page
alignment.
So limit the last write to be only the required number of bytes, rounded up to
the hard sector size of the device.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a raid0 has a component device larger than 4TB, and is accessed on a 32bit
machines, then as 'chunk' is unsigned long,
chunk << chunksize_bits
can overflow (this can be as high as the size of the device in KB). chunk
itself will not overflow (without triggering a BUG).
So change 'chunk' to be 'sector_t, and get rid of the 'BUG' as it becomes
impossible to hit.
Cc: "Jeff Zheng" <Jeff.Zheng@endace.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no reason i2o_max_drivers must be a power of two. This patch
eliminates such a constraint.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Maximum number of I2O drivers which could be registered is configurable by
max_drivers module parameter.
But the module parameter is ignored and default value (I2O_MAX_DRIVERS = 8)
is used in the loops to notify all registered drivers.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i2o_driver_register() initalizes event queue for driver only when
drv->event is set. So similarly the event queue should be destroyed only
when drv->event is set in the error path. Otherwise destroy_workqueue()
will called with NULL.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
phantom, take care of pci posting
thanks to akpm for pointing this out
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
phantom's ioctl is often (4000 times a sec or so) invoked, don't acquire
BKL and block other processes.
Signed-off-by: Jiri Slaby <xslaby@phantom.fi.muni.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
info->pseudo_palette was previously kmalloced. Do not overwrite it afterwards
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are some small fixes for the imxfb framebuffer driver:
- remove ifndef for MX1FS2 platform which is not present in the kernel.
- REV, CLS, PS and SPL_SPR are only needed with some sharp displays.
Only setup the corresponding io pins when such a display is connected.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Use the FB_SYS_* operations instead of the FB_CFB_* operations as the
actual frame buffer memory is part of system RAM
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix compile warnings from w100fb.c. Attribute registration failure doesn't
stop the driver working so just warn about it.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- fix 16-bit RGBA 4444 and 5551 modes (use fbset -rgba to set them)
- kill wmb() after each register write by PM3_SLOW_WRITE_REG
- kill inaccurate comments (leftovers from skeletonfb.c)
- kill PCI class restriction, now it is more general and shorter
- white spaces and other minor fixes and source reducing
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a possible barriers problem in RDAC_WR functions, then
remove redudant ones.
It also removes one unneeded register load from blitter function().
Signed-off-by: Krzysztof.Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch puts all SBUS/UPA selection under one option "SBUS/UPA
framebuffers" and moves all sparc specific drivers next to them in one group.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'ioc' should be deallocated if __copy_from_user fails (found by Coverity
- CID 1644).
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Message size needs to be checked before copying, or bad things could
happen.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix mpc5200 PSC SPI driver to actually work for CONFIG_PPC_MERGE
- s/mpc52xx/mpc5200/, as this was changed in device tree some time ago
- fix spi id detection
The move from 'ppc' to 'powerpc' didn't quite match the latest
kernel.org code.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Dragos Carp <dragos.carp@toptica.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a few entries in ata_device_blacklist[] in libata-core.c
marked with HORKAGE_NODMA but are missing from drive_blacklist[]
in ide-dma.c. This patch makes the lists in sync.
Also remove a duplicated entry for "SanDisk SDP3B-64".
Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Compiling with '-Wswitch-enum' I noticed following:
CC drivers/ide/ide-proc.o
drivers/ide/ide-proc.c: In function âproc_ide_read_imodelâ:
drivers/ide/ide-proc.c:54: warning: enumeration value âide_etrax100â not handled in switch
drivers/ide/ide-proc.c:54: warning: enumeration value âide_acornâ not handled in switch
How about the following patch?
Signed-off-by: Mika Kukkonen <mikukkon@iki.fi>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It turns out from customer reports to Red Hat and some PCI dumps that the
MegaIDE in RAID mode doesn't provide the drive tuning data that the
serverworks driver expects but sometimes does provide something that
fools the code.
For the RAID class case skip the oem setup and don't trust the BIOS data.
We then tune from scratch and this sorts it out. (This has been confirmed
on an afflicted IBM blade)
[libata serverworks.c never trusts the BIOS in the first place so is
accidentally immune]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add the IDE device ID to atiixp_pci_tbl struct in atiixp.c for ATI SB700.
From: Henry Su <henry.su@amd.com>
Signed-off-by: Luugi Marsan <luugi.marsan@amd.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If a QP is attached to a shared receive queue (SRQ), then it doesn't
have a receive queue (RQ). So don't allocate an RQ doorbell (or map a
doorbell from userspace for userspace QPs) for that QP.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (29 commits)
USB: Add support for Olimex arm-usb-ocd JTAG interface serial port
USB: Add support for Sierra Wireless Aircard 595U
USB: ldusb bugfix
USB: ftdi_sio: Add USB Product Id for OpenDCC
USB: fix ratelimit call semantics
USB: handle errors in power/level attribute
USB: make the autosuspend workqueue thread freezable
USB: Fix USB OHCI Subvendor for Toshiba Portege 4000
USB: usblp: Use correct DMA address in case of probe error
USB: Fix debug output of ark3116
USB: Onetouch - switch to using input_dev->dev.parent
USB: don't try to kzalloc 0 bytes
USB: remove short initial timeout for device descriptor fetch
USB: Deref URB after usbmon is done with it
USB: Remove duplicate IDs from option card driver
USB: auerswald: fix file release handler
USB: fsl_usb2_udc: Fix UMTI_WIDE support and a compile warning
USB: set the correct Interrupt interval in usb_bulk_msg
USB: New device PID for ftdi_sio driver
USB: remove unneeded WARN_ON
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ads7846 - SPI_CPHA mode bugfix
Input: ads7846 - document that it handles tsc2046 too
Input: input-polldev - add module info
Input: ucb1x00-ts - remove commented out code
Input: ucb1400_ts - use sched_setscheduler()
Input: ALPS - force stream mode
Input: iforce - minor clean-ups
Input: iforce - fix force feedback not working
Input: adbhid - do not access input_dev->private directly
Input: logips2pp - add type 72 (PS/2 TrackMan Marble)
Fix config warning related to select usage:
drivers/macintosh/Kconfig:117:warning: 'select' used by config symbol 'PMAC_APM_EMU' refers to undefined symbol 'SYS_SUPPORTS_APM_EMULATION'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The UCC_GETH Kconfig option in drivers/net/Kconfig had a line to select the
UCC_FAST option is arch/powerpc/sysdev/qe_lib/Kconfig, which is only used
on PowerPC builds. On other architectures, this would generated a warning.
The fix is to have UCC_FAST depend on UCC_GETH.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the serial port on Olimex arm-usb-ocd
JTAG interface.
The device appears as two serial ports, but the first one is reserved
for the JTAG interface. The JTAG interface can be used with OpenOCD
from userspace. For more information, please see:
http://openocd.berlios.de/web/http://www.olimex.com/dev/arm-usb-ocd.html
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the newly released Aircard 595U EVDO
modem to the Sierra Wireless driver (sierra.c) in kernel 2.6.21.
I suspect that my mailer may be mangling patches so let me know and
I'll try to resend it.
From: Danny Budik <dbudik@ist-traffic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a problem reported with consecutive reads in the ldusb
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB product id registration for the OpenDCC (www.opendcc.de)
model railway central unit. Applies to 2.6.21.1.
Signed-off-by: Guido Scholz <guido.scholz@bayernline.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as910) fixes a ratelimit modification so that the
original error-handling path will be followed even when the log-rate
limitation kicks in.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as906) improves the error handling for the USB power/level
attribute file. If an error occurs, the original power-level settings
will be restored.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as881b) makes the ksuspend_usb_wq workqueue freezable. We
don't want a rogue workqueue thread running around, unexpectedly
suspending or resuming USB devices in the middle of a system sleep
transition.
This fixes Bugzilla #8498.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a bug in an OHCI quirk handler for Portege 4000; the
Subvendor is 0x1179 (PCI_VENDOR_ID_TOSHIBA)
not 0x102f (PCI_VENDOR_ID_TOSHIBA_2)
bugid 8510
00:02.0 USB Controller [0c03]: ALi Corporation USB 1.1 Controller
[10b9:5237] (rev 03) (prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems Unknown device [1179:0004]
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at f7eff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looks like the error path had a copy-paste error. The normal exit path
uses correct URB already.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix debug output. Previously, it would output "0xFFFFFFB0" on 32-bit
archs (and probably "0xFFFFFFFFFFFFFFB0" on 64-bits), because buf is
taken as signed char, which is promoted to signed int, while %x always
expects an unsigned int.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Also, do not access input_dev->private directly, use helpers.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as907) prevents us from trying to allocate 0 bytes
when an interface has no endpoint descriptors.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as905) removes a micro-optimization from the hub port
initialization code. Previously we had been using a short timeout on
the first attempt the read the device descriptor; now we will use the
standard timeout length.
It's not clear that the short timeout ever provided any benefit. And
now we know of one case where it actually hurts: The device can't meet
the short timeout and then it gets terminally confused.
This fixes Bugzilla #8444.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I haven't personally run across an oops because of this, but I feel safer
with this fix in place.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If this down_interruptible() does fail due to signal_pending() then the state
of the driver will get trashed in interesting ways, because userspace cannot
and will not retry the close().
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change PORT_WIDTH bit for UMTI_WIDE mode and fix a compile warning
introduced in last revision.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as902) fixes a mistake I introduced into usb_bulk_msg().
usb_fill_int_urb() already does the bit-shifting calculation for
high-speed Interrupt intervals; it shouldn't be done twice.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Hello,
I need to use MaxStream's PKG-U modules which includes a ftdi sio chipset for
usb2serial communication, here are the patches for handling Maxstream's modules.
The VID & PID to use with the open-source driver are provided on the CD-ROM
bundled with the modules.
From: Neil Superna ARMSTRONG <superna@na-prod.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as883) removes an out-of-date WARN_ON from the main HCD
endpoint-disable routine. The warning is triggered whenever an
endpoint is disabled while the root hub is suspended. In the past
that may not have been legal, but it definitely is legal now. Merely
unbinding a USB driver will do it.
Furthermore, I've never seen any occurrences of this warning that
really did signal an actual bug or error condition. At this point it
has outlived its purpose.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch (as879) ties up some loose ends from an earlier patch.
These are things I didn't think to include at the time but which
clearly belonged there.
If an autosuspend fails because driver activity races with
the autosuspend call, restart the autosuspend timer.
When a device is resumed by an external request, it counts
as device activity and should update the last_busy time so
that the next autoresume won't occur immediately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as882) fixes a problem with the EHCI BIOS handoff. On my
machine, the BIOS configures the controller and the handoff fails,
leaving the controller configured. During resume-from-disk, this
confuses ehci-hcd into thinking that the controller has not been
tampered with.
The problem is fixed by turning off the Configured Flag whenever a
BIOS handoff is attempted, whether it succeeds or not.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the issue of drivers claiming multiple interfaces. Operations
are stopped as soon as an interface is suspend and resumed only as
all interfaces have been resumed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Workaround another device firmware bug, wherein CDC descriptors get
placed in a wrong place never previously observed in the wild.
Fix a bug where a seeming RNDIS device returns a bogus response during
device initialization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Partial fix for bogosity in the ftdi-elan and u132-hcd drivers ... these
have no business including with the internals of other drivers, much less
doing so in a broken way!!
A previous patch resolved one build fix, this resolves another...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Sitecom WL-117 is another "driverless" ZD1211 device where the virtual
windows driver CD must be ejected before the WLAN device appears.
zd1211rw takes care of the ejecting, but usb-storage must be told not to claim
the device.
From: Matthew Davidson <mj.davidson@gmail.com>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the transfer of allocating the descriptor in attach and no longer in open
was incomplete resulting in a memory leak coverity spotted. This fix
is against the patch set you posted.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit [1] the SPI mode is set to 1, but it should be 0. As stated
in the commit, ads784x samples the data on the rising edge. SPI mode 1
samples on the falling edge [2] though.
The root cause of this is a bug in the omap_uwire code, which treats
CPHA=1 incorrectly; so these two bugs cancel each other out on one
of the main regression test platforms for this driver.
[1] kernel.org GIT 7937e86a70
[2] http://en.wikipedia.org/wiki/Serial_Peripheral_Interface_Bus
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The TSC2046 is an updated version of the ADS7846 ... mention that in
the Kconfig helptext and driver source.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is required to load it as a module, as GPL-compatible
license is necessary to use workqueues.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
![](/avatar/362e80bc9fa0d4c6d6e2a8a86ae5d0d0?size=56 "Neil \\"Superna\\" ARMSTRONG"){kind=small}
