The resume bug was caused not by an early interrupt but because the idle
timeout was not being stopped on suspend. Also disable hardware IRQ's
on suspend. Will need to revisit this with hotplug?
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The hardware should be fully shut off during suspend, and the base
irq mask restored during resume.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the poll routine detects no hardware available, it needs to dequeue
it self from the network poll list. Linus didn't understand NAPI.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is cleaner, to not loop over both ports if only one exists.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The set power state function is cleaner if it doesn't return anything.
The only caller that could fail is in suspend() and it can check the argument
there.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes two independent problems: it would not save the PCI state on
suspend (and thus try to resume a nonexistent state on resume), and
while shut off, if an interrupt happened on the same shared irq, the irq
handler would react very badly to the interrupt status being an invalid
all-ones state.
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
convert au1000_eth driver to use PHY framework and garbage collected
functions and identifiers that became unused/obsolete in the process
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Priority: not critical; makes init code discardable.
Fix section mismatch warnings:
WARNING: drivers/net/3c501.o - Section mismatch: reference to .init.text:el1_probe from .text between 'init_module' (at offset 0x812) and 'cleanup_module'
WARNING: drivers/net/3c503.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x661) and 'cleanup_card'
WARNING: drivers/net/3c505.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x228d) and 'cleanup_module'
WARNING: drivers/net/3c507.o - Section mismatch: reference to .init.text:el16_probe from .text between 'init_module' (at offset 0xa99) and 'cleanup_module'
WARNING: drivers/net/3c523.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x12e7) and 'cleanup_module'
WARNING: drivers/net/3c527.o - Section mismatch: reference to .init.text:mc32_probe from .text between 'init_module' (at offset 0xd8d) and 'cleanup_module'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Priority: not critical; makes init code discardable.
Removes one duplicate assignment.
Fix section mismatch warnings:
WARNING: drivers/net/smc-ultra.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x369) and 'cleanup_card'
WARNING: drivers/net/smc-ultra32.o - Section mismatch: reference to .init.text:ultra32_probe from .text between 'init_module' (at offset 0x254) and 'cleanup_module'
WARNING: drivers/net/smc9194.o - Section mismatch: reference to .init.text:smc_init from .text between 'init_module' (at offset 0x997) and 'cleanup_module'
WARNING: drivers/net/smc9194.o - Section mismatch: reference to .init.data: from .data between 'smcdev.0' (at offset 0x44) and '__param_str_io'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Priority: not critical; makes init code discardable.
Fix section mismatch warnings:
WARNING: drivers/net/hp-plus.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x387) and 'cleanup_card'
WARNING: drivers/net/hp.o - Section mismatch: reference to .init.data: from .text between 'hp_init_card' (at offset 0x310) and 'init_module'
WARNING: drivers/net/hp.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x367) and 'cleanup_card'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Sat, 10 Jun 2006 14:11:42 +0200 (MEST) Mikael Pettersson wrote:
> While compiling 2.6.17-rc6 for a 486 with an NE2000 ISA ethernet card, I got:
>
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x158) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x176) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x183) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x1ea) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x251) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x266) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x29b) and 'ne_block_input'
>
> Not sure how serious this is; the driver seems to work fine later on.
Doesn't look serious. init_module() is not __init, but it calls
some __init functions and touches some __initdata.
BTW, I would be happy to see some consistent results from modpost
section checking. I don't see all of these warnings (I see only 1)
when using gcc 3.3.6. What gcc version are you using?
Does that matter? (not directed at anyone in particular)
Patch below fixes it for me. Please test/report.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If a PCI bus error/fault triggers a PCI bus reset, attempts to get the
ethernet packet count statistics from the hardware will fail, returning
garbage data upstream. This patch skips statistics data collection if the
PCI device is not on the bus.
This patch presumes that an earlier patch,
[PATCH] PCI Error Recovery: e1000 network device driver
has already been applied.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In file included from drivers/net/smc911x.c:84:
drivers/net/smc911x.h:46:9: warning: "SMC_USE_16BIT" is not defined
drivers/net/smc911x.h:60:9: warning: "SMC_USE_32BIT" is not defined
drivers/net/smc911x.h:73:10: warning: "SMC_USE_PXA_DMA" is not defined
drivers/net/smc911x.c: In function `smc911x_reset':
drivers/net/smc911x.c:247: warning: implicit declaration of function `SMC_inl'
drivers/net/smc911x.c:249: warning: implicit declaration of function `SMC_outl'
Cc: Dustin McIntire <dustin@sensoria.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains new device ids for forcedeth ethernet.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch bumps up the version number for config support.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for diagnostic tests through ethtool support.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch moves a few functions (no logic change) so that the next
patch has these functions defined.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch exposes hardware statistic counters through ethtool support.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch allows for configurable rx and tx checksum offloads through
ethtool support.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes configuration bugs when modifying wol settings.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes configuration bugs when modifying phy settings.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch allows for configurable flow control through ethtool support.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch allows for configurable ring size through ethtool support.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are a series of patches for configuration support in forcedeth and
one patch for device ids.
This patch is a cleanup of the a previous TSO patch.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Get rid of all the SUN_570X logic and instead:
1) Make sure MEMARB_ENABLE is set when we probe the SRAM
for config information. If that is off we will get
timeouts.
2) Always try to sync with the firmware, if there is no
firmware running do not treat it as an error and instead
just report it the first time we notice this condition.
3) If there is no valid SRAM signature, assume the device
is onboard by setting TG3_FLAG_EEPROM_WRITE_PROT.
Update driver version and release date.
With help from Michael Chan and Fabio Massimo Di Nitto.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes boards don't reset properly, and the address read out of the
EEPROM is zero. Stop the insanity before the device gets registered.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The transmit side code has a number of ring problems that caused some
of the Bugzilla reports. Rather than trying to fix the details, it is safer
to rewrite the code that handles transmit completion and freeing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Consolidate all usage of ring low water mark to one value.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since accessing the PHY can take 100's of usecs, use a work queue to
allow spinning in outside of soft/hard irq.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The following patch updates the myri10ge to 1.0.0, with the following changes:
* Switch to dma_alloc_coherent API.
* Avoid PCI burst when writing the firmware on chipset with unaligned completions.
* Use ethtool_op_set_tx_hw_csum instead of ethtool_op_set_tx_csum.
* Include linux/dma-mapping.h to bring DMA_32/64BIT_MASK on all architectures
(was missing at least on alpha).
* Some typo and warning fixes.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew J. Gallatin <gallatin@myri.com>
drivers/net/myri10ge/myri10ge.c | 57 +++++++++++++++++++-----------
1 file changed, 37 insertions(+), 20 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Various PCI bus errors can be signaled by newer PCI controllers.
This patch adds the PCI error recovery callbacks to the intel gigabit
ethernet e1000 device driver. The patch has been tested, and appears
to work well.
Signed-off-by: Linas Vepstas <linas@linas.org>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Various PCI bus errors can be signaled by newer PCI controllers. This
patch adds the PCI error recovery callbacks to the intel ethernet e100
device driver. The patch has been tested, and appears to work well.
Signed-off-by: Linas Vepstas <linas@linas.org>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
It was brought to our attention that the prefetches break e1000 traffic
on xscale/arm architectures. Remove them for now. We'll let them
stay in mm for a while, or find a better solution to enable.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
New code added in 2.6.17 caused setup_irq to print a warning when
running ethtool -t eth0 offline.
This test marks the request_irq call made by this test as a "probe"
to see if the interrupt is shared or not.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
skb_clone() may fail, we should check the result.
Coverity CID: 1215.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Matt Mackall <mpm@selenic.com>
netconsole is being wrong here. If it wasn't enabled there's no error.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
zd1201 is wifi adapter, yet it is hiding in drivers/usb/net where
noone can find it. This moves Kconfig/Makefile zd1201 to the right
place.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug logging in bcm43xx_ieee80211_set_security() is pretty noisy.
Make it more silent.
Signed-off-by: Jason Lunz <lunz@falooley.org>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
