On vbus_session() call, optionally activate D+ pullup
resistor and enable the udc, or deactivate D+ pullup
resistor and disable the udc.
It is intentional to not handle any VBus sense related irq.
An external transceiver driver (like gpio_vbus) should
catch VBus sense signal, and call usb_gadget_vbus_connect()
or usb_gadget_vbus_disconnect().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prepare pxa27x_udc to handle usb D+ pullup properly : it
should connect the pullup resistor and disconnect it only
if no external transceiver is handling it.
[ dbrownell@users.sourceforge.net: kerneldoc and gpio fixes ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call usb_gadget_vbus_connect() and ...disconnect() from a
workqueue rather than from an irq handler, allowing msleep()
calls in vbus_session. Update kerneldoc to match.
[ dbrownell@users.sourceforge.net: more kerneldoc updates ]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usblp in 2.6.18 polled for status regardless if we actually needed it.
At some point I dropped it, to save the batteries if nothing else.
As it turned out, printers exist (e.g. Canon BJC-3000) that need prodding
this way or else they stop. This patch restores the old behaviour.
If you want to save battery, don't leave jobs in the print queue.
I tested this on my printers by printing and examining usbmon traces
to make sure status is being requested and printers continue to print.
Tuomas Jäntti verified the fix on BJC-3000.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1203) increases the max_sector limit for USB tape
drives. By default usb-storage sets max_sectors to 240 (i.e., 120 KB)
for all devices. But tape drives need a higher limit, since tapes can
and do have very large block sizes. Without the ability to transfer
an entire large block in a single command, such tapes can't be used.
This fixes Bugzilla #12207.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Phil Mitchell <philipm@sybase.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Restore some code that was wrongly dropped from the RNDIS
driver, and caused interop problems observed with OpenMoko.
The issue is with hardware which needs help conforming to part
of the USB 2.0 spec (section 8.5.3.2); some can automagically
send a ZLP in response to an unexpected IN, but not all chips
will do that. We don't need to check the packet length ourselves
the way earlier code did, since the UDC must already check it.
But we do need to tell the UDC when it must force a short packet
termination of the data stage.
(Based on a patch from Aric D. Blumer <aric at sdgsystems.com>)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently the Configuration and Interface strings aren't used as
often as the Vendor, Product, and Serial strings. In at least one
device (a Saitek Cyborg Gold 3D joystick), attempts to read the
Configuration string cause the device to stop responding to Control
requests.
This patch (as1226) adds a quirks flag, telling the kernel not to
read a device's Configuration or Interface strings, together with a
new quirk for the offending joystick.
Reported-by: Melchior FRANZ <melchior.franz@gmail.com>
Tested-by: Melchior FRANZ <melchior.franz@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.28 and 2.6.29, nothing earlier]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "c-enter" USB to Toshiba 1.8" IDE enclosure needs special treatment
to work flawlessly. This patch is absolutely trivial, as the integrated
USB-IDE bridge is already identified to be an "unusual" device, only the
bcdDevice is different (lower) to the bcdDeviceMin already included in
the kernel.
It is a Prolific 2507 bridge.
T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=067b ProdID=2507 Rev= 0.01
S: Manufacturer=Prolific Technology Inc.
S: Product=ATAPI-6 Bridge Controller
S: SerialNumber=00000272
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Thomas Bartosik <tbartdev@gmx-topmail.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Option GTM380 in Modem mode uses Product ID 0x7201. This has been tested and works
on production systems for over 6 months.
Signed-off-by: Achilleas Kotsis <akots@exponent.gr>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* newer versions of the Novatel Wireless U727 CDMA 3G USB stick
have a different Product ID (0x5010); adding this ID makes them
work just fine with the option driver
Signed-off-by: Dirk Hohndel <hohndel@infradead.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current firmware revision 5.60 still behaves the same,
so update the quirk up a (non-existing) 99.99 revision.
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=493415
Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Tested-by: Jan Heitkoetter <devnull@heitkoetter.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
The generic cdc-acm driver is now the best one to handle Sony Ericsson
F3507g-based devices (which the Dell 5530 is a rebrand of), now that all
the pieces are in place (ie, cac477e8f1).
Removing the IDs from option allows cdc-acm to handle the device.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1225) fixes a bug in ehci-hcd. The condition for
whether unlinked QHs can become IDLE should not be that the controller
is halted, but rather that the controller isn't running. In other
words when the root hub is suspended, the hardware doesn't own any
QHs.
This fixes a problem that can show up during hibernation: If a QH is
only partially unlinked when the root hub is frozen, then when the
root hub is thawed the QH won't be in the IDLE state. As a result it
can't be used properly for new URB submissions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Brandon Philips <brandon@ifup.org>
Tested-by: Brandon Philips <brandon@ifup.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ehci-hcd uses usb_get_urb() and usb_put_urb() in an unbalanced way causing
isochronous URB's kref.counts incrementing once per usb_submit_urb() call.
The culprit is *usb being set to NULL when usb_put_urb() is called after URB
is given back.
Due to other fixes there is no need for ehci-hcd to deal with usb_get_urb()
nor usb_put_urb() anymore, so patch removes their usages in ehci-hcd.
Patch also makes ehci_to_hcd(ehci)->self.bandwidth_allocated adjust, if a
stream finishes.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Please consider this small patch for the usb option-card driver.
This patch adds the ZTE 622 usb modem device.
Signed-off-by: Albert Pauw <albert.pauw@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure we don't leak locked vstdev->lock in vstusb_write. Unlock
properly on one fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is an omitted unlock in mdc800_usb_probe's fail path. Add it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Henning Zabel <henning@uni-paderborn.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We do not hold mutex in one place in cxacru_cm, but unlock it on fail path.
Fix this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Simon Arlott <cxacru@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbfs driver manages a list of completed asynchronous URBs. But
it is too eager to free the entries on this list: destroy_async() gets
called whenever an interface is unbound or a device is removed, and it
deallocates the outstanding struct async entries for all URBs on that
interface or device. This is wrong; the user program should be able
to reap an URB any time after it has completed, regardless of whether
or not the interface is still bound or the device is still present.
This patch (as1222) moves the code for deallocating the completed list
entries from destroy_async() to usbdev_release(). The outstanding
entries won't be freed until the user program has closed the device
file, thereby eliminating any possibility that the remaining URBs
might still be reaped.
This fixes a bug in which a program can hang in the USBDEVFS_REAPURB
ioctl when the device is unplugged.
Reported-and-tested-by: Martin Poupe <martin.poupe@upek.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver already supports the 1 protocol support, so just add it to
the MODULE_DEVICE_TABLE entry so it properly picks up these devices.
Thanks to Jouni Rynö for pointing this out.
Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
open() will never succeed, as we always return -ENODEV. Fix this
obvious bug.
Thanks to Jouni Ryno for reporting it.
Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The SRP sysfs attribute is dependent on gadget mode; any
gadget may support SRP. But "rmmod musb_hdrc" didn't
remove that attribute; fix.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If this is not done, khubd will not be informed of the disconnect
and will assume the device is still there.
Easily seen when a hub is connected with no device attached to it;
it will autosuspend. When the hub is disconnected, it still shows
up in /proc/bus/usb/devices
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove wrongly applied upper limit on the interrupt transfer
interval for low speed devices (not much of an error per se,
according to USB specs).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Feeding 32-bit length cast down to 'u16' to min() to calculate the FIFO
count in musb_host_tx() risks sending a short packet prematurely for
transfer sizes over 64 KB.
Similarly, although data transfer size shouldn't exceed 65535 bytes for
the control endpoint, making musb_h_ep0_continue() more robust WRT URBs
with possibly oversized buffer will not hurt either...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For some strange reason the host side musb_giveback() decides
that it's always got an IN transfer when the hardware endpoint
is using a shared FIFO. This causes musb_save_toggle() to read
the toggle state from the RXCSR register instead of TXCSR, and
may also cause unneeded reloading of RX endpoint registers.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The musb_h_disable() routine can oops in some cases:
- It's not safe to read hep->hcpriv outside musb->lock,
since it gets changed on completion IRQ paths.
- The list iterators aren't safe to use in that way;
just remove the first element while !list_empty(),
so deletions on other code paths can't make trouble.
We need two "scrub the list" loops because only one branch
should touch hardware and advance the schedule.
[ dbrownell@users.sourceforge.net: massively simplify
patch description; add key points as code comments ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The urb_dequeue() method forgets to unlink 'struct musb_qh' from the
control or bulk schedules when the URB being cancelled is the only
one queued to its endpoint. That will cause musb_advance_schedule()
to block once it reaches 'struct musb_qh' with now empty URB list, so
URBs queued for other endpoints after the one being dequeued will not
be served.
Fix by unlinking the QH from the list except when it's already being
handled (typically by musb_giveback). Since a QH with an empty URB
list is now supposed to be freed, do that. And remove a now-useless
check from musb_advance_schedule().
[ dbrownell@users.sourceforge.net: update patch description,
and fold in a dequeue() comment patch ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The input queue should be used for TX on endpoints which
share FIFO hardware. The host TX path wasn't doing that.
Shared FIFOs are most often configured for periodic endpoints,
which are mostly used for RX/IN transfers ... that's probably
how this bug managed to linger for a long time.
[ dbrownell@users.sourceforge.net: update patch description ]
Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
request->actual is an unsigned and we should use the same
variable type for fifo_count otherwise we might lose some
data if request->length >= 64kbytes.
[ dbrownell@users.sourceforge.net: fix compiler warning ]
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the musb build fixes for DaVinci got merged (RC3?), kick in
the other bits needed to get it finally *working* in mainline:
- Use clk_enable()/clk_disable() ... the "always enable USB clocks"
code this originally relied on has since been removed.
- Initialize the USB device only after the relevant I2C GPIOs are
available, so the host side can properly enable VBUS.
- Tweak init sequencing to cope with mainline's relatively late init
of the I2C system bus for power switches, transceivers, and so on.
Sanity tested on DM6664 EVM for host and peripheral modes; that system
won't boot with CONFIG_PM enabled, so OTG can't yet be tested. Also
verified on OMAP3.
(Unrelated: correct the MODULE_PARM_DESC spelling of musb_debug.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1218) fixes a problem with a radio-control joystick used
in the "walkera 4#3" helicopter. This device responds to the initial
Get-String-Descriptor request for string 0 (which is really the list
of supported languages) by sending its config descriptor! The
usb_get_string() routine needs to check whether it got the right
type of descriptor.
Oddly enough, this sort of check is already present in
usb_get_descriptor(). The patch changes the error code from -EPROTO
to -ENODATA, because -EPROTO shows up in so many other contexts to
indicate a hardware failure rather than a firmware error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Guillermo Jarabo <williamjap@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
===================================================================
In apollon case, it only used udc, so udc configuration should select
USB_OTG_UTILS also.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1220) automatically disables stalls when g_file_storage
finds itself running with an Atmel device controller, because the
Atmel hardware/driver isn't capable of halting bulk endpoints
correctly.
Reported-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1219) adds the IGNORE_RESIDUE flag to the unusual_devs
entries for Genesys Logic's USB-IDE adapter. Although this device
usually gets the residue correct, there is one command crucial to the
operation of CD and DVD drives which it messes up.
Tested-by: Mike Lampard <mike@mtgambier.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed that my revision of the F3507G WWAN card isn't listed in
drivers/usb/serial/option.c
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the cdc-acm driver can
properly handle this combined device.
Signed-off-by: Dmitriy Taychenachev <dimichxp@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch addes the BenQ 3g modem support to the option driver.
From: Jesse Sung <jsung@novell.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We where selecting wrong ep descriptors causing
some troubles while sending files over obex interface.
The problem was a typo while usb_find_endpoint() was being
called for HS endpoints.
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently ITDs are immediately recycled whenever their URB completes.
However, EHCI hardware can sometimes remember some ITD state. This
means that when the ITD is reused before end-of-frame it may sometimes
cause the hardware to reference bogus state.
This patch defers reusing such ITDs by moving them into a new ehci member
cached_itd_list. ITDs resting in cached_itd_list are moved back into their
stream's free_list once scan_periodic() detects that the active frame has
elapsed.
This makes the snd_usb_us122l driver (in kernel since .28) work right
when it's hooked up through EHCI.
[ dbrownell@users.sourceforge.net: comment fixups ]
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Tested-by: Philippe Carriere <philippe-f.carriere@wanadoo.fr>
Tested-by: Federico Briata <federicobriata@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clear next TD field and status field in queue head initialization code
to prevent unpredictable result caused by residue of usb reset.
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
*ep->reg_udccs is always set to 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
