There are a few places in the ipath driver where a variable is
re-declared within a block where it is already in scope. Most of these
extra declarations can simply be removed, since the variable from the
outer scope is used in a way so that it does not need to keep its
variable across the block with the re-declaration.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use round_jiffies() to align ehca's 1-second timer with other timers
and potentially save power by sleeping cores for longer.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The original QHT7040 had significant performance issues so there was an
additional check in the driver for a newer serial number. Support for
the small quantities of that board shipped has been dropped, so this
patch removes the special checks to simplify the code.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Different chips have different width interrupt status registers, so add
a flag and accessor function to decide which width register read to use.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The 6110 had a bug that caused some registers to be swapped; it was
fixed for the 7220 (and didn't affect the 6120 because it had fewer
registers). This adds a flag and related code to handle that, and
includes some minor cleanups in the same area.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
The number of configured ports for the 7220 changes the number of eager
TIDs available per port, for all but port 0 (kernel port) which remains
constant, so add a field to give port0 count separate from the portdata
structure.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
User registers have different alignments on different chips (4KB on
older, 64KB on 7220). Allow mapping the user registers on kernels with
page sizes up to 64K.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Various hardware counters are exported via the ipath file system (since
it is binary data). The old file format was very dependent on the HW
offsets for these registers. Newer HCA chips can have different
counters at different offsets. This patch adds a level of indirection
to make the file format consistent across HCAs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for QLogic HCAs which have hardware performance sampling
registers for PortSamplesControl and PortSamplesResult MADs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch moves some arrays that were defined per-device to be
variables defined in the per context data structure, thus avoiding extra
kzalloc() calls.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In preparation for upcoming chips that have different values for
INFINIPATH_R_PORTENABLE_SHIFT, INFINIPATH_R_INTRAVAIL_SHIFT,
INFINIPATH_R_TAILUPD_SHIFT, and portcfg_shift, remove the shared
#defines and use device-specific variables instead.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
kreceive is now portdata * instead of devdata * and other kreceive
related cleanups....
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove an unused parameter and fix up the comment.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a couple of minor problems with RNR NAK handling:
- The insertion sort was causing extra delay when inserting ahead
vs. behind an existing entry on the list.
- A resend of a first packet of a message which is still not ready,
needs another RNR NAK (i.e., it was suppressed when it shouldn't).
- Also, the resend tasklet doesn't need to be woken up unless the
ACK/NAK actually indicates progress has been made.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch allows ehca to forward event client-reregister-required to
registered clients. One such event is generated by a switch eg. after
its reboot.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rather than byte-swapping cqe->g_mlpath_rqpn each time we extract a
field from it, byte-swap it once into a temporary variable. This
results in smaller, better code -- eg, on 32-bit x86:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-5 (-5)
function old new delta
mlx4_ib_poll_cq 1188 1183 -5
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove MSI support from the mthca driver, as scheduled. There is no
reason to use MSI instead of MSI-X, since MSI-X performs better. No
one has spoken up since MSI support was deprecated in commit f6be6fbe
("IB/mthca: Schedule MSI support for removal"), so apparently the MSI
support is unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add the work completion error code to the QP error debug output.
This makes it easier to determine the cause of the error.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
An internal code review found the comment here lacking -- update it with
more specifics of how and why the rmb() is there.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During a code review, someone noticed the comments didn't match the code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The gen2_basic tests check for the errno value when a CQ is resized
smaller than the number of outstanding completions queue on the CQ.
This patch changes ib_ipath to return EINVAL which is what ib_mthca
returns and what gen2_basic expects.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Code review pointed out that the locking around uses of ipath_sendctrl
and kr_sendctrl were, in several places, incorrect and/or inconsistent.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At one point in time there was code to allow a user process to
wait for a send buffer if none were available. This feature was
never used and most of the code was removed. This removes
some missed unused code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The 5.0 firmware now supports translating sgls in recv work requests,
so remove the host driver logic currently doing the translation.
Note: this change requires 5.0 firmware.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently the call into cxgb3 to get the driver info is not serialized.
The iw_cxgb3 module needs to hold the rtnl_lock around the ethtool ops
call like dev_ioctl() does.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Tested-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch is in response to reviewing a patch to the core MAD
processing which fixes loopback of directed route packets to/from user
level MAD agents. This change enables the core code to work for
ib_ipath by fixing the return code from the ipath process_mad method.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Improve interrupt handler cache footprint by noinline'ing error
functions that are rarely called.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 23b9c1ab ("Infiniband: make ipath driver use default driver
groups.") introduced a bug in the ipath driver where
ipath_device_create_group() fell through into the error path, even on
success, which meant that the sysfs groups it created would always get
removed right away. This made ipath_device_remove_group() hit the
BUG_ON() in sysfs_remove_group() when it tried to remove those groups a
second time.
Correct the return path so that the groups stick around until they are
supposed to be cleaned up.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make the ipath driver use the new driver functions so that it does not
touch the sysfs portion of the driver structure.
We also remove the redundant symlink from the device back to the driver,
as it is already in the sysfs tree. Any userspace tools should be using
the standard symlink, not some driver specific one.
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: Arthur Jones <arthur.jones@qlogic.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a small bug in ipath_ud_rcv()'s handling of UD messages
with immediate data. We need to test whether immediate data is
present and update the header size accordingly *before* testing the
packet size from the header against the actual received length.
Otherwise the wrong header size will be used and all messages with
immediate data will be dropped.
This bug keeps MVAPICH-UD and HP MPI from working at all on ipath devices.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the value of pkey_index in completions to get a valid value for
GSI QPs. Without this fix, incoming GSI packets on port 2 get an
invalid P_Key index in the completion, which prevents the MAD layer
from sending back a response, which can make the second port of
ConnectX HCAs completely useless.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Several pSeries firmware versions share a rare locking issue in the
HCA-related hCalls. Check for a feature flag that indicates the issue
being fixed and serialize all HCA hCalls if not.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Firmware would round up the number of SGEs to four, because the WQE
structure holds four SGEs. For SRQ, only three are supported, so return
a fixed value instead.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The formula would yield -1 if the path is faster than the link, which
is wrong in a bad way (max throttling). Clamp to 0, which is the
correct value.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Wrong choice of port number caused modify_qp() to fail -- fixed.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error codes for ib_post_send(), ib_post_recv(), and ib_post_srq_recv()
were inconsistent. Use EINVAL for too many SGEs and ENOMEM for too many
WRs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The wrong offset was being returned to libipathverbs so that when
ibv_modify_srq() calls mmap(), it always fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the code which frees the partially allocated QP
resources if there was an error while creating the QP. In particular,
the QPN wasn't deallocated and the QP wasn't removed from the hash
table.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The wrong offset was being returned to libipathverbs so that when
ibv_resize_cq() calls mmap(), it always fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The device attribute max_qp_init_rd_atom is not getting set in cxgb3's
query_device method. Version 1.0.4 of librdmacm now validates the
user's requested initiator and responder resources against the max
supported by the device. Since iw_cxgb3 wasn't setting this attribute
(and it defaulted to 0), all rdma_connect()s fail if there are
initiator resources requested by the app. Fix this by setting the
correct value in iwch_query_device().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPD (inter-packet delay) formula was a little off and assumed a
fixed physical link rate; fix the formula and query the actual
physical link rate, now that we can get it. Also, refactor the
calculation into a common function ehca_calc_ipd() and use that
instead of duplicating code.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
