The nl80211 rule flags were being used.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed led device naming for the ath9k driver. Due to the
documentation of the led subsystem/class the naming should be
"devicename:colour:function" while not applying sections
should be left blank.
This should lead to e.g. "ath9k-%s::rx" instead of "ath9k-%s:rx".
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 notifies the RC algorithm if RTS/CTS and short preamble
are needed. The RC flags for MCS rates are currently not handled
by mac80211, and ath9k's RC doesn't set the flags either. Fix this.
Also, set the rts_cts_rate_idx inside the RC algorithm.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interface to calculate the TX rate for a data frame
was convoluted with lots of redundant arguments being
passed around. Remove all of that and make it simple.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX filter masks are already defined in enum ath9k_rx_filter
in ath9k.h
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we have new found information about our location and the
current country regulatory domain does not have passive scan
flag requirements we should be able to actively scan now on those
channels.
Since AP functionality is not allowed where passive scan flags are
set this means if you have a world regulatory domain and you get a
country IE that allows that channel (with active scan) then we lift
the passive-scan requirement so you can then use AP mode.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to use our internal wireless mode variable when
cfg80211 already has its own.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable operating mode specific interrupts in ath9k_add_interface instead
of ath9k_start.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removing the module was slow because ath9k_hw_stopdma()
was looping for a long time quantum. Use reasonable
values now to fix this issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an issue where hw_value_short was not being filled
with the proper ratecode during rate registration, but was being used
in the RX path for decoding the packet rate.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee80211_sta pointer in the SKB's TX control info
area is not guaranteed to be valid after returning from the tx() callback.
Use ieee80211_find_sta() instead and return early if the station
is no longer present.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default chainmask for AR9280 is 3, so handle that when setting
the supported MCS rates. Also, check for the HW supported chainmask
when choosing single/dual stream.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Versioning for ath9k is pointless we have kept it at 0.1
since the initial release so its meaningless. We put more emphasis
on kernel release or dated wireless-testing master tag
as per John's tagging.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix AR9285 specific noise floor reads and initialize tx and rx
chainmask during reset. This along with the following earlier
patches of ath9k fixes an issue with association noticed in
noisy environment.
ath9k: Fix typo in chip version check
ath9k: Remove unnecessary gpio configuration in ath9k_hw_reset()
ath9k: Fix bug in NF calibration
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With debugging enabled and with ATH_DBG_REGULATORY
selected we wouldn't get the full print out of one line,
reason is we used "," instead of nothing to separate two
lines.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables low-level driver independent debugging of the TSF and remove the driver specific things of ath5k and ath9k from the debugfs.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of chainmasks for AR9285 weren't being
setup when running NF calibration.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dual stream capability must be registered only when the
hardware supports it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9285 based devices support only single stream MCS rates.
This patch fixes a bug where dual stream stream rates were
also being registered.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds an ath9k specific entry to read, write and reset the TSF into the debugfs, like in ath5k. This makes debugging the IBSS handling of wifi drivers _much_ easier.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that cfg80211 has its own regulatory infrastructure we can
condense ath9k's regulatory code considerably. We only keep data
we need to provide our own regulatory_hint(), reg_notifier() and
information necessary for calibration.
Atheros hardware supports 12 world regulatory domains, since these
are custom we apply them through the the new wiphy_apply_custom_regulatory().
Although we have 12 we can consolidate these into 5 structures based on
frequency and apply a different set of flags that differentiate them on
a case by case basis through the reg_notifier().
If CRDA is not found our own custom world regulatory domain is applied,
this is identical to cfg80211's except we enable passive scan on most
frequencies.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements dynamic power save feature for ath9k.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The buffer state is already cleared in ATH_TXBUF_RESET.
Remove redundant code clearing the type variable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up the convoluted buffer management
logic for TX aggregation. Both aggregation creation and
completion are addressed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the current holding descriptor is the last one in the TX queue,
*and* it has been marked as STALE, then move it to the free list
and bail out, as it has already been processed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX queue draining routines have confusing names,
rename them approprately and merge ath_drain_txdataq()
with ath_drain_all_txq().
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch starts cleaning up all the crufty code in transmission path,
grouping functions into logical blocks.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate control algorithm needs to know if a STA allows
short guard interval, fixing this allows RC to use the correct
table.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calculation of rate indices from ratecode is done in recv.c
in a straightforward manner for both HT and legacy rates.
This variable is not needed anymore.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because we have support for the AR9100 devices now, we can enable them.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In 'ath9k_ani_reset' the 'ahp->ah_curani' will be initialized only
if 'DO_ANI(ah)' true. In 'ath9k_hw_ani_monitor' we are using
'ahp->ah_curani' unconditionally, and it will cause a NULL pointer
dereference on AR9100.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing the register at offset 0x98c4 causes a deadlock on the AR913x
SoCs. Although i don't have detailed knowledge about these registers,
but if i change the register offset according to the 'ar5416Addac' table,
it works. Additionally there is no reference to the 0x98c4 elsewhere.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RTC register offsets don't fit into 'u16' on the AR913x, so we have
to remove the existing casts.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On the AR913x SOCs we have to provide EEPROM contents via platform_data,
because accessing the flash via MMIO is not safe. Additionally different
boards may store the radio calibration data at different locations.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the platform_driver itself, and modifies the main driver
to register it.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we have converted all bus specific routines to replaceable, we
can move the PCI specific codes into a separate file.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have left only some PCI specific cleanup code. We have to convert
them as well.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCI specific bus_read_cachesize routine won't work on the AHB bus,
we have to replace it with a suitable one later.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
