PCI still doesn't work on sh7785lcr 29bit 256M map mode.
On SH7785, PCI -> SHwy address translation is not base+offset but
somewhat like base|offset (See HW Manual (rej09b0261) Fig. 13.11).
So, you can't export CS2,3,4,5 by 256M at CS2 (results CS0,1,2,3
exported, I guess). There are two candidates.
a) 128M@CS2 + 128M@CS4
b) 512M@CS0
Attached patch is B. It maps 512M Byte at 0 independently of memory
size. It results CS0 to CS6 and perhaps some more being accessible
from PCI.
Tested on
7785lcr 29bit 128M map
7785lcr 29bit 256M map
(NOT tested on 32bit)
Signed-off-by: Takashi YOSHII <yoshii.takashi@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There were a number of issues with the DSP context save/restore code,
mostly left-over relics from when it was introduced on SH3-DSP with
little follow-up testing, resulting in things like task_pt_dspregs()
referencing incorrect state on the stack.
This follows the MIPS convention of tracking the DSP state in the
thread_struct and handling the state save/restore in switch_to() and
finish_arch_switch() respectively. The regset interface is also updated,
which allows us to finally be rid of task_pt_dspregs() and the special
cased task_pt_regs().
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This accidentally regressed when the multi-IRQ changes went in,
switching SH7091 from 4 to 6 channels. Add SH7091 back in to the
4-channel dependency list.
Reported-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
Pass the original flags to rwlock arch-code, so that it can re-enable
interrupts if implemented for that architecture.
Initially, make __raw_read_lock_flags and __raw_write_lock_flags stubs
which just do the same thing as non-flags variants.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Forcing direct-mapped worked on certain older 2-way set associative
parts, but was always error prone on 4-way parts. As these are the
norm these days, there is not much point in continuing to support this
mode. Most of the folks that used direct-mapped mode generally just
wanted writethrough caching in the first place..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
cpuidle wants ARCH_HAS_DEFAULT_IDLE defined in order to use the
default idle loop. So, make it accessible and enable it for all
sh machines.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a 'noiotrap' kernel command line option to permit disabling of
I/O trapping. This is mostly useful for running on emulators where the
physical device limitations are not an issue.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the requisite patches have gone in, this can safely be enabled
across the board for all of the 32-bit SH platforms.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Triggers -Werror on gcc-4.3:
arch/sh/kernel/setup.c: In function 'early_parse_mem':
arch/sh/kernel/setup.c:111: error: format not a string literal and no format arguments
...
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the V4L bits have finally settled..
This patch adds support for a secondary ov772x camera on ap325rxa.
This is supported in addition to the regular soc_camera_platform camera.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the ifndef __ASSEMBLY__ preprocessor to allow the
defines in the file to be used also in assembly code.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Kexec is not likely to work on NON-MMU CPU because this added
depend on MMU for kexec.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All soc-camera camera and host drivers must specify supported data signal
polarity, after all drivers are fixed, we'll add a suitable test to
soc_camera_bus_param_compatible().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Impact: cleanup
It's unused, since about 1995. So remove all initialization of it in
preparation for actually removing the field.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Everyone defines it, and only one person uses it
(arch/mips/sgi-ip27/ip27-nmi.c). So just open code it there.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-mips@linux-mips.org
Waiting for a free bus now accepts the timeout value in jiffies and does
proper checking using time_before.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (32 commits)
x86: disable __do_IRQ support
sparseirq, powerpc/cell: fix unused variable warning in interrupt.c
genirq: deprecate obsolete typedefs and defines
genirq: deprecate __do_IRQ
genirq: add doc to struct irqaction
genirq: use kzalloc instead of explicit zero initialization
genirq: make irqreturn_t an enum
genirq: remove redundant if condition
genirq: remove unused hw_irq_controller typedef
irq: export remove_irq() and setup_irq() symbols
irq: match remove_irq() args with setup_irq()
irq: add remove_irq() for freeing of setup_irq() irqs
genirq: assert that irq handlers are indeed running in hardirq context
irq: name 'p' variables a bit better
irq: further clean up the free_irq() code flow
irq: refactor and clean up the free_irq() code flow
irq: clean up manage.c
irq: use GFP_KERNEL for action allocation in request_irq()
kernel/irq: fix sparse warning: make symbol static
irq: optimize init_kstat_irqs/init_copy_kstat_irqs
...
Polaris is an SMSC reference platform with a SH7709S CPU and LAN9118
ethernet controller. This patch adds support for it.
Updated following feedback from Nobuhiro Iwamatsu.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rework the hd64461 demuxer code to fix the HD64461 level-triggered
interrupts handling, using handle_level_irq() as needed.
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Older versions of kexec-tools has a zImage loader that
passes a virtual address as entry point. The elf loader
otoh it passes a physical address as entry point, and
pages are always passed as physical addresses as well.
Only allow physical addresses from now on.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Save and restore ftrace state when returning from kexec jump in
machine_kexec(). Follows the x86 change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For the time being, this creates far more problems than it solves,
evident by the second local_irq_disable(). Kill all of this off
and rely on IRQ disabling to protect against the VBR reload.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add kexec jump support to the SuperH architecture.
Similar to the x86 implementation, with the following
exceptions:
- Instead of separating the assembly code flow into
two parts for regular kexec and kexec jump we use a
single code path. In the assembly snippet regular
kexec is just kexec jump that never comes back.
- Instead of using a swap page when moving data between
pages the page copy assembly routine has been modified
to exchange the data between the pages using registers.
- We walk the page list twice in machine_kexec() to
do and undo physical to virtual address conversion.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rework the kexec code to avoid using P2SEG. Instead
we walk the page list in machine_kexec() and convert
the addresses from physical to virtual using C.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Setup the vbr register in machine_kexec(). This
instead of passing values to the assembly snippet.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the ARM change from Aaro Koskinen:
When unmapping N pages (e.g. shared memory) the amount of TLB
flushes done can be (N*PAGE_SIZE/ZAP_BLOCK_SIZE)*N although it
should be N at maximum. With PREEMPT kernel ZAP_BLOCK_SIZE is 8
pages, so there is a noticeable performance penalty when
unmapping a large VMA and the system is spending its time in
flush_tlb_range().
The problem is that tlb_end_vma() is always flushing the full VMA
range. The subrange that needs to be flushed can be calculated by
tlb_remove_tlb_entry(). This approach was suggested by Hugh
Dickins, and is also used by other arches.
The speed increase is roughly 3x for 8M mappings and for larger
mappings even more.
Bits and peices are taken from the ARM patch as well as the existing
arch/um implementation that is quite similar.
The end result is a significant reduction in both partial and full TLB
flushes initiated through flush_tlb_range().
At the same time, the nommu implementation was broken, had a superfluous
cache flush, and subsequently would have triggered a BUG_ON() if a
code-path had triggered it. Tidy this up for correctness and provide a
nopped-out implementation there.
More background on the initial discussion can be found at:
http://marc.info/?t=123609820900002&r=1&w=2http://marc.info/?t=123660375800003&r=1&w=2
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While harmless, PTEA has different semantics on these parts, and is only
used in extended TLB mode. Kill off the legacy support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for extended ASIDs (up to 16-bits) on newer SH-X3 cores
that implement the PTAEX register and respective functionality. Presently
only the 65nm SH7786 (90nm only supports legacy 8-bit ASIDs).
The main change is in how the PTE is written out when loading the entry
in to the TLB, as well as in how the TLB entry is selectively flushed.
While SH-X2 extended mode splits out the memory-mapped U and I-TLB data
arrays for extra bits, extended ASID mode splits out the address arrays.
While we don't use the memory-mapped data array access, the address
array accesses are necessary for selective TLB flushes, so these are
implemented newly and replace the generic SH-4 implementation.
With this, TLB flushes in switch_mm() are almost non-existent on newer
parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
IRQ for sh_eth of sh7763rdp became multi handling.
Therefore, the IRQ number of sh_eth is changed, too.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the ESPT-Giga (Ethernet Serial Parallel
Translator) SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With arch/sh/drivers/dma/ always being built, the Dreamcast DMA engines
are being unconditionally built in, regardless of whether the DMA API is
enabled or not. This is a regression from previous behaviour, but there
is not much advantage in building them all in unconditionally regardless.
Add a new config option to make it optional, and update the only user of
it to reflect that.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When SuperH CPU has IRQ multi of DMAC, SH_DMA_IRQ_MULTI becomes enable.
The following CPU's are Multi IRQ of DMAC now.
- SH775X and SH7091
- SH776X
- SH7780
- SH7785
If SH_DMA_IRQ_MULTI becomes enable, dma-sh api driver is optimized
for Multi IRQ.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a possible problem in the resume from
hibenration. It temporaneally saves the clk->rate on the
stack to avoid any possible change during the clk->set_parent(..)
call.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve the ap325 board code to allow the lcd panel
and backlight to be powered off.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.
To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
dma-sh's get_dma_error_irq() is only used by SH4, as the SH3
doesn't have the DMA Error interrupt.
Disable it out for non-SH4 builds.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements preliminary suspend/resume support for the PMB.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve the sh7785lcr power off implementation to
never return. It takes some time before the board
is actually powered off, just hang after asking
the harware to power down.
This removes the serial port garbage printout.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds PM support to the clock framework.
With this, resume from hibernation is properly supported.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the clk_set_parent/clk_get_parent routines to the sh
clock framework.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds DMA support for newer SH-4A CPUs, particularly SH7763/64/80/85.
This also enables multi IRQ support for platforms that have multiple
vectors bound to the same IRQ source.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the problem that cannot work a PCI device when 32-bit physical
address mode.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a new defconfig for SH7785LCR in 32-bit mode, and update the power
off code to avoid 29-bit assumptions.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.
P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If CONFIG_PM is set, let Migo-R LEDs show sleep states.
D11 will show STATUS0 and D12 PDSTATUS.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Other compilation errors were revised by commit of
"sh: ap325rxa: Revert ov772x support"
(08c2f5b4d7) but other compilation
errors are given.
We revert this commit and need to add new header(media/soc_camera.h).
This change revises new compilation error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.
To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.
The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.
Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was accidentally dropped in the multiple vectors per irq conversion.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7763 hardware
blocks such as RTC/SCIF/DMAC/GETHER/PCIC5/MMCIF/SIM/GPIO/USBF.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786-based Urquell board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786 CPU subtype.
While this is a dual-core CPU, only UP is supported for now. L2 cache
support is likewise not yet implemented.
More information on this particular CPU subtype is available at:
http://www.renesas.com/fmwk.jsp?cnt=sh7786_root.jsp&fp=/products/mpumcu/superh_family/sh7780_series/sh7786_group/
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the recent entry.S refactoring, the SH-X3 path had a mov.l for a
register to register copy, resulting in:
AS arch/sh/kernel/cpu/sh4/../sh3/entry.o
arch/sh/kernel/cpu/sh4/../sh3/entry.S: Assembler messages:
arch/sh/kernel/cpu/sh4/../sh3/entry.S:366: Error: invalid operands for opcode
make[3]: *** [arch/sh/kernel/cpu/sh4/../sh3/entry.o] Error 1
Switch it over to a mov to fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7785 hardware
blocks such as SCIF/DMAC/PCIC5/MMCIF/GDTA/FLCTL/GPIO
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7780 hardware
blocks such as SCIF/RTC/DMAC/PCIC5/MMCIF/FLCTL/GPIO
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh775x hardware
blocks such as SCI/SCIF/RTC/DMAC/TMU2/REF.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Instead of keeping the single vector -> single linux irq mapping
we extend the intc code to support merging of vectors to a single
linux irq. This helps processors such as sh7750, sh7780 and sh7785
which have more vectors than masking ability. With this patch in
place we can modify the intc tables to use one irq per maskable
irq source. Please note the following:
- If multiple vectors share the same enum then only the
first vector will be available as a linux irq.
- Drivers may need to be rewritten to get pending irq
source from the hardware block instead of irq number.
This patch together with the sh7785 specific intc tables solves
DMA controller irq issues related to buggy interrupt masking.
Reported-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix iounmap() of pass-through P4 addresses. Without this patch
iounmap() on the sh7780 rtc area results in a warning message.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH-3 does not support 'pref'-based prefetching, only SH-2A and SH-4A
parts do. Remove SH-3 from the list.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Prefetch early exception data. There is unused space in our
exception handler cache line anyway, so this is almost free.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove EXPEVT vector from the stack, lookup_exception_vector()
for sh3/sh4/sh4a is already using k2 to get the vector.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the sh3/sh4/sh4a register restore code in
the following ways:
- break out restore_regs() from restore_all()
- the register saving order is unchanged
- use restore_regs() in sh_bios_handler and restore_all
- document the function
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the sh3/sh4/sh4a register saving code in
the following ways:
- break out prepare_stack_save_dsp() from handle_exception()
- break out save_regs() from handle_exception()
- the register saving order is unchanged
- align new functions to fit in cache lines
- separate exception code from interrupt code
- keep main code flow in a single cache line per exception vector
- use bsr/rts for regular functions (save pr first)
- keep data in one shared cache line (exception_data)
- document the functions
- tie in the hp6xx code
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This change depends on some v4l changes that have been pushed back to
2.6.30, so drop this and fall back on the old soc_camera code until then.
Reported-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Acked-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
