This patch fixes a warning in the disable_nonboot_cpus call in
kernel/power/smp.c.
Signed-off by: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's the patch again to fix the code to handle if the values between
MAX_USER_RT_PRIO and MAX_RT_PRIO are different.
Without this patch, an SMP system will crash if the values are
different.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
RLIMIT_RTPRIO is supposed to grant non privileged users the right to use
SCHED_FIFO/SCHED_RR scheduling policies with priorites bounded by the
RLIMIT_RTPRIO value via sched_setscheduler(). This is usually used by
audio users.
Unfortunately this is broken in 2.6.13rc3 as you can see in the excerpt
from sched_setscheduler below:
/*
* Allow unprivileged RT tasks to decrease priority:
*/
if (!capable(CAP_SYS_NICE)) {
/* can't change policy */
if (policy != p->policy)
return -EPERM;
After the above unconditional test which causes sched_setscheduler to
fail with no regard to the RLIMIT_RTPRIO value the following check is made:
/* can't increase priority */
if (policy != SCHED_NORMAL &&
param->sched_priority > p->rt_priority &&
param->sched_priority >
p->signal->rlim[RLIMIT_RTPRIO].rlim_cur)
return -EPERM;
Thus I do believe that the RLIMIT_RTPRIO value must be taken into
account for the policy check, especially as the RLIMIT_RTPRIO limit is
of no use without this change.
The attached patch fixes this problem.
Signed-off-by: Andreas Steinmetz <ast@domdv.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The suspend to disk code was a poor copy of the code in
sys_reboot now that we have kernel_power_off, kernel_restart
and kernel_halt use them instead of poorly duplicating them inline.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We know the system is in trouble so there is no question if this
is an emergecy :)
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We already do all of the gymnastics to run from process context
to call the power off code so call into the power off code cleanly.
This especially helps acpi as part of it's shutdown logic should
run acpi_shutdown called from device_shutdown which was not
being called from here.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the kernel is working well and we want to restart cleanly
kernel_restart is the function to use. But in many instances
the kernel wants to reboot when thing are expected to be working
very badly such as from panic or a software watchdog handler.
This patch adds the function emergency_restart() so that
callers can be clear what semantics they expect when calling
restart. emergency_restart() is expected to be callable
from interrupt context and possibly reliable in even more
trying circumstances.
This is an initial generic implementation for all architectures.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is obvious we wanted to call kernel_restart here
but since we don't have it the code was expanded inline and hasn't
been correct since sometime in 2.4.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because the factors of sys_reboot don't exist people calling
into the reboot path duplicate the code badly, leading to
inconsistent expectations of code in the reboot path.
This patch should is just code motion.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the recent addition of device_suspend calls into
sys_reboot two code paths were missed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This moves the inotify sysctl knobs to "/proc/sys/fs/inotify" from
"/proc/sys/fs". Also some related cleanup.
Signed-off-by: Robert Love <rml@novell.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
inotify is intended to correct the deficiencies of dnotify, particularly
its inability to scale and its terrible user interface:
* dnotify requires the opening of one fd per each directory
that you intend to watch. This quickly results in too many
open files and pins removable media, preventing unmount.
* dnotify is directory-based. You only learn about changes to
directories. Sure, a change to a file in a directory affects
the directory, but you are then forced to keep a cache of
stat structures.
* dnotify's interface to user-space is awful. Signals?
inotify provides a more usable, simple, powerful solution to file change
notification:
* inotify's interface is a system call that returns a fd, not SIGIO.
You get a single fd, which is select()-able.
* inotify has an event that says "the filesystem that the item
you were watching is on was unmounted."
* inotify can watch directories or files.
Inotify is currently used by Beagle (a desktop search infrastructure),
Gamin (a FAM replacement), and other projects.
See Documentation/filesystems/inotify.txt.
Signed-off-by: Robert Love <rml@novell.com>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dup_mmap of a VM_DONTCOPY vma forgot to lower the child's total_vm. (But
no way does this account for the recent report of total_vm seen too low.)
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kernel/power/disk.c needs a declaration of name_to_dev_t() in scope. mount.h
seems like an appropriate choice.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Free some RAM before entering S3 so that upon
resume we can be sure early allocations will succeed.
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Register an "acpi" system device to be notified of shutdown preparation.
This depends on CONFIG_PM
http://bugzilla.kernel.org/show_bug.cgi?id=4041
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The BKS might be reacquired before we have dropped PREEMPT_ACTIVE, which
could trigger a second could trigger a second cond_resched() call. Bug
found by Hirofumi Ogawa.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new section called ".data.read_mostly" for data items that are read
frequently and rarely written to like cpumaps etc.
If these maps are placed in the .data section then these frequenly read
items may end up in cachelines with data is is frequently updated. In that
case all processors in an SMP system must needlessly reload the cachelines
again and again containing elements of those frequently used variables.
The ability to share these cachelines will allow each cpu in an SMP system
to keep local copies of those shared cachelines thereby optimizing
performance.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Shobhit Dayal <shobhit@calsoftinc.com>
Signed-off-by: Christoph Lameter <christoph@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
freezeable() already tests for TRACED/STOPPED processes, no need to do it
twice.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix error handling and whitespace in swsusp.c. swsusp_free() was called when
there was nothing allocating, leading to oops.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move device name resolution code around so that it is not called from
resume-from-initrd. name_to_dev_t may be unavailable at that point.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following renames arch_init, a kprobes function for performing any
architecture specific initialization, to arch_init_kprobes in order to
cleanup the namespace.
Also, this patch adds arch_init_kprobes to sparc64 to fix the sparc64 kprobes
build from the last return probe patch.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Anyone reporting a stuck IRQ should try these options. Its effectiveness
varies we've found in the Fedora case. Quite a few systems with misdescribed
IRQ routing just work when you use irqpoll. It also fixes up the VIA systems
although thats now fixed with the VIA quirk (which we could just make default
as its what Redmond OS does but Linus didn't like it historically).
A small number of systems have jammed IRQ sources or misdescribes that cause
an IRQ that we have no handler registered anywhere for. In those cases it
doesn't help.
Signed-off-by: Alan Cox <number6@the-village.bc.nu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As Steven Rostedt pointed out, there are 2 problems with ITIMER_REAL
timers.
1. do_setitimer() does not call del_timer_sync() in case
when the timer is not pending (it_real_value() returns 0).
This is wrong, the timer may still be running, and it can
rearm itself.
2. It calls del_timer_sync() with tsk->sighand->siglock held.
This is deadlockable, because timer's handler needs this
lock too.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use msleep() in a few places.
Signed-off-by: Luca Falavigna <dktrkranz@gmail.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch tweaks idle thread setup semantics a bit: instead of setting
NEED_RESCHED in init_idle(), we do an explicit schedule() before calling
into cpu_idle().
This patch, while having no negative side-effects, enables wider use of
cond_resched()s. (which might happen in the stock kernel too, but it's
particulary important for voluntary-preempt)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following is the second version of the function return probe patches
I sent out earlier this week. Changes since my last submission include:
* Fix in ppc64 code removing an unneeded call to re-enable preemption
* Fix a build problem in ia64 when kprobes was turned off
* Added another BUG_ON check to each of the architecture trampoline
handlers
My initial patch description ==>
From my experiences with adding return probes to x86_64 and ia64, and the
feedback on LKML to those patches, I think we can simplify the design
for return probes.
The following patch tweaks the original design such that:
* Instead of storing the stack address in the return probe instance, the
task pointer is stored. This gives us all we need in order to:
- find the correct return probe instance when we enter the trampoline
(even if we are recursing)
- find all left-over return probe instances when the task is going away
This has the side effect of simplifying the implementation since more
work can be done in kernel/kprobes.c since architecture specific knowledge
of the stack layout is no longer required. Specifically, we no longer have:
- arch_get_kprobe_task()
- arch_kprobe_flush_task()
- get_rp_inst_tsk()
- get_rp_inst()
- trampoline_post_handler() <see next bullet>
* Instead of splitting the return probe handling and cleanup logic across
the pre and post trampoline handlers, all the work is pushed into the
pre function (trampoline_probe_handler), and then we skip single stepping
the original function. In this case the original instruction to be single
stepped was just a NOP, and we can do without the extra interruption.
The new flow of events to having a return probe handler execute when a target
function exits is:
* At system initialization time, a kprobe is inserted at the beginning of
kretprobe_trampoline. kernel/kprobes.c use to handle this on it's own,
but ia64 needed to do this a little differently (i.e. a function pointer
is really a pointer to a structure containing the instruction pointer and
a global pointer), so I added the notion of arch_init(), so that
kernel/kprobes.c:init_kprobes() now allows architecture specific
initialization by calling arch_init() before exiting. Each architecture
now registers a kprobe on it's own trampoline function.
* register_kretprobe() will insert a kprobe at the beginning of the targeted
function with the kprobe pre_handler set to arch_prepare_kretprobe
(still no change)
* When the target function is entered, the kprobe is fired, calling
arch_prepare_kretprobe (still no change)
* In arch_prepare_kretprobe() we try to get a free instance and if one is
available then we fill out the instance with a pointer to the return probe,
the original return address, and a pointer to the task structure (instead
of the stack address.) Just like before we change the return address
to the trampoline function and mark the instance as used.
If multiple return probes are registered for a given target function,
then arch_prepare_kretprobe() will get called multiple times for the same
task (since our kprobe implementation is able to handle multiple kprobes
at the same address.) Past the first call to arch_prepare_kretprobe,
we end up with the original address stored in the return probe instance
pointing to our trampoline function. (This is a significant difference
from the original arch_prepare_kretprobe design.)
* Target function executes like normal and then returns to kretprobe_trampoline.
* kprobe inserted on the first instruction of kretprobe_trampoline is fired
and calls trampoline_probe_handler() (no change here)
* trampoline_probe_handler() consumes each of the instances associated with
the current task by calling the registered handler function and marking
the instance as unused until an instance is found that has a return address
different then the trampoline function.
(change similar to my previous ia64 RFC)
* If the task is killed with some left-over return probe instances (meaning
that a target function was entered, but never returned), then we just
free any instances associated with the task. (Not much different other
then we can handle this without calling architecture specific functions.)
There is a known problem that this patch does not yet solve where
registering a return probe flush_old_exec or flush_thread will put us
in a bad state. Most likely the best way to handle this is to not allow
registering return probes on these two functions.
(Significant change)
This patch series applies to the 2.6.12-rc6-mm1 kernel, and provides:
* kernel/kprobes.c changes
* i386 patch of existing return probes implementation
* x86_64 patch of existing return probe implementation
* ia64 implementation
* ppc64 implementation (provided by Ananth)
This patch implements the architecture independant changes for a reworking
of the kprobes based function return probes design. Changes include:
* Removing functions for querying a return probe instance off a stack address
* Removing the stack_addr field from the kretprobe_instance definition,
and adding a task pointer
* Adding architecture specific initialization via arch_init()
* Removing extern definitions for the architecture trampoline functions
(this isn't needed anymore since the architecture handles the
initialization of the kprobe in the return probe trampoline function.)
Signed-off-by: Rusty Lynch <rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that PPC64 has no-execute support, here is a second try to fix the
single step out of line during kprobe execution. Kprobes on x86_64 already
solved this problem by allocating an executable page and using it as the
scratch area for stepping out of line. Reuse that.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates the CFQ io scheduler to the new time sliced design (cfq
v3). It provides full process fairness, while giving excellent
aggregate system throughput even for many competing processes. It
supports io priorities, either inherited from the cpu nice value or set
directly with the ioprio_get/set syscalls. The latter closely mimic
set/getpriority.
This import is based on my latest from -mm.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1. Establish a simple API for process freezing defined in linux/include/sched.h:
frozen(process) Check for frozen process
freezing(process) Check if a process is being frozen
freeze(process) Tell a process to freeze (go to refrigerator)
thaw_process(process) Restart process
frozen_process(process) Process is frozen now
2. Remove all references to PF_FREEZE and PF_FROZEN from all
kernel sources except sched.h
3. Fix numerous locations where try_to_freeze is manually done by a driver
4. Remove the argument that is no longer necessary from two function calls.
5. Some whitespace cleanup
6. Clear potential race in refrigerator (provides an open window of PF_FREEZE
cleared before setting PF_FROZEN, recalc_sigpending does not check
PF_FROZEN).
This patch does not address the problem of freeze_processes() violating the rule
that a task may only modify its own flags by setting PF_FREEZE. This is not clean
in an SMP environment. freeze(process) is therefore not SMP safe!
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes use of ALIGN() to remove duplicate round-up code.
Signed-off-by: Nick Wilson <njw@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment for msleep_interruptible() is wrong, as it will ignore
wait-queue events, but will wake up early for signals.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Following patch provides purely cosmetic changes and corrects CodingStyle
guide lines related certain issues like below in kexec related files
o braces for one line "if" statements, "for" loops,
o more than 80 column wide lines,
o No space after "while", "for" and "switch" key words
o Changes:
o take-2: Removed the extra tab before "case" key words.
o take-3: Put operator at the end of line and space before "*/"
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Makes kexec_crashdump() take a pt_regs * as an argument. This allows to
get exact register state at the point of the crash. If we come from direct
panic assertion NULL will be passed and the current registers saved before
crashdump.
This hooks into two places:
die(): check the conditions under which we will panic when calling
do_exit and go there directly with the pt_regs that caused the fatal
fault.
die_nmi(): If we receive an NMI lockup while in the kernel use the
pt_regs and go directly to crash_kexec(). We're probably nested up badly
at this point so this might be the only chance to escape with proper
information.
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Vivek Goyal" <vgoyal@in.ibm.com>
o Support for /proc/vmcore interface. This interface exports elf core image
either in ELF32 or ELF64 format, depending on the format in which elf headers
have been stored by crashed kernel.
o Added support for CONFIG_VMCORE config option.
o Removed the dependency on /proc/kcore.
From: "Eric W. Biederman" <ebiederm@xmission.com>
This patch has been refactored to more closely match the prevailing style in
the affected files. And to clearly indicate the dependency between
/proc/kcore and proc/vmcore.c
From: Hariprasad Nellitheertha <hari@in.ibm.com>
This patch contains the code that provides an ELF format interface to the
previous kernel's memory post kexec reboot.
Signed off by Hariprasad Nellitheertha <hari@in.ibm.com>
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for retrieving the address of elf core header if one
is passed in command line.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch provides the interfaces necessary to read the dump contents,
treating it as a high memory device.
Signed off by Hariprasad Nellitheertha <hari@in.ibm.com>
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Following patch exports kexec global variable "crash_notes" to user space
through sysfs as kernel attribute in /sys/kernel.
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a minor bug fix in kexec to resolve the problem of loading panic
kernel with initrd.
o Problem: Loading a capture kenrel fails if initrd is also being loaded.
This has been observed for vmlinux image for kexec on panic case.
o This patch fixes the problem. In segment location and size verification
logic, minor correction has been done. Segment memory end (mend) should be
mstart + memsz - 1. This one byte offset was source of failure for initrd
loading which was being loaded at hole boundary.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces the architecture independent implementation the
sys_kexec_load, the compat_sys_kexec_load system calls.
Kexec on panic support has been integrated into the core patch and is
relatively clean.
In addition the hopefully architecture independent option
crashkernel=size@location has been docuemented. It's purpose is to reserve
space for the panic kernel to live, and where no DMA transfer will ever be
setup to access.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a new preemption model: 'Voluntary Kernel Preemption'. The
3 models can be selected from a new menu:
(X) No Forced Preemption (Server)
( ) Voluntary Kernel Preemption (Desktop)
( ) Preemptible Kernel (Low-Latency Desktop)
we still default to the stock (Server) preemption model.
Voluntary preemption works by adding a cond_resched()
(reschedule-if-needed) call to every might_sleep() check. It is lighter
than CONFIG_PREEMPT - at the cost of not having as tight latencies. It
represents a different latency/complexity/overhead tradeoff.
It has no runtime impact at all if disabled. Here are size stats that show
how the various preemption models impact the kernel's size:
text data bss dec hex filename
3618774 547184 179896 4345854 424ffe vmlinux.stock
3626406 547184 179896 4353486 426dce vmlinux.voluntary +0.2%
3748414 548640 179896 4476950 445016 vmlinux.preempt +3.5%
voluntary-preempt is +0.2% of .text, preempt is +3.5%.
This feature has been tested for many months by lots of people (and it's
also included in the RHEL4 distribution and earlier variants were in Fedora
as well), and it's intended for users and distributions who dont want to
use full-blown CONFIG_PREEMPT for one reason or another.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only sane way to clean up the current 3 lock_kernel() variants seems to
be to remove the spinlock-based BKL implementations altogether, and to keep
the semaphore-based one only. If we dont want to do that for whatever
reason then i'm afraid we have to live with the current complexity. (but
i'm open for other cleanup suggestions as well.)
To explore this possibility we'll (at a minimum) have to know whether the
semaphore-based BKL works fine on plain SMP too. The patch below enables
this.
The patch may make sense in isolation as well, as it might bring
performance benefits: code that would formerly spin on the BKL spinlock
will now schedule away and give up the CPU. It might introduce performance
regressions as well, if any performance-critical code uses the BKL heavily
and gets overscheduled due to the semaphore. I very much hope there is no
such performance-critical codepath left though.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch consolidates the CONFIG_PREEMPT and CONFIG_PREEMPT_BKL
preemption options into kernel/Kconfig.preempt. This, besides reducing
source-code, also enables more centralized tweaking of preemption related
options.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds the core update_cpu_domains code and updated cpusets documentation
Signed-off-by: Dinakar Guniguntala <dino@in.ibm.com>
Acked-by: Paul Jackson <pj@sgi.com>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patches add dynamic sched domains functionality that was
extensively discussed on lkml and lse-tech. I would like to see this added to
-mm
o The main advantage with this feature is that it ensures that the scheduler
load balacing code only balances against the cpus that are in the sched
domain as defined by an exclusive cpuset and not all of the cpus in the
system. This removes any overhead due to load balancing code trying to
pull tasks outside of the cpu exclusive cpuset only to be prevented by
the tasks' cpus_allowed mask.
o cpu exclusive cpusets are useful for servers running orthogonal
workloads such as RT applications requiring low latency and HPC
applications that are throughput sensitive
o It provides a new API partition_sched_domains in sched.c
that makes dynamic sched domains possible.
o cpu_exclusive cpusets sets are now associated with a sched domain.
Which means that the users can dynamically modify the sched domains
through the cpuset file system interface
o ia64 sched domain code has been updated to support this feature as well
o Currently, this does not support hotplug. (However some of my tests
indicate hotplug+preempt is currently broken)
o I have tested it extensively on x86.
o This should have very minimal impact on performance as none of
the fast paths are affected
Signed-off-by: Dinakar Guniguntala <dino@in.ibm.com>
Acked-by: Paul Jackson <pj@sgi.com>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
