Update the tda18271c2_rf_tracking_filters_correction function to include
the modified temperature compensation calculatation formula as described
in Rev.04 of the TDA18271HD datasheet.
Signed-off-by: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't display "no agc configuration provided" unless DBG_ADV is set.
Fix comments in function, tda18271_agc. This config variable is not
for LNA configuration -- it is for external AGC configuration.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Display function parameters, idx and len, in error log.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the case of multiple tuner instances, ensure that non-default
configuration options are saved into the driver's state.
This resolves an issue where a configuration option may not be
carried into the driver if the analog side of a hybrid driver
initializes before the digital side.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
minor cleanup: move small_i2c assignment to the state config block
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For better readability, treat the low power standby mode configuration
as an output option feature configuration, and change it to a bitmask.
If left unconfigured, all features will remain enabled, just as the
default configuration was before these changes were introduced.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By default, the driver enters standby mode with slave tuner output
loop thru enabled and xtal oscillator on.
Not all designs require that slave tuner output loop thru and
xtal oscillator remain active while in standby mode, so two
additional standby modes have been added:
- standby mode with xtal oscillator on (loop thru off)
- total power off
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, V4L uses a scancode table whose index is the scancode and
the value is the keycode. While this works, it has some drawbacks:
1) It requires that the scancode to be at the range 00-7f;
2) keycodes should be masked on 7 bits in order for it to work;
3) due to the 7 bits approach, sometimes it is not possible to replace
the default keyboard to another one with a different encoding rule;
4) it is different than what is done with dvb-usb approach;
5) it requires a typedef for it to work. This is not a recommended
Linux CodingStyle.
This patch is part of a larger series of IR changes. It basically
replaces the IR_KEYTAB_TYPE tables by a structured table:
struct ir_scancode {
u16 scancode;
u32 keycode;
};
This is very close to what dvb does. So, a further integration with DVB
code will be easy.
While we've changed the tables, for now, the IR keycode handling is still
based on the old approach.
The only notable effect is the redution of about 35% of the ir-common
module size:
text data bss dec hex filename
6721 29208 4 35933 8c5d old/ir-common.ko
5756 18040 4 23800 5cf8 new/ir-common.ko
In thesis, we could be using above u8 for scancode, reducing even more the size
of the module, but defining it as u16 is more convenient, since, on dvb, each
scancode has up to 16 bits, and we currently have a few troubles with rc5, as their
scancodes are defined with more than 8 bits.
This patch itself shouldn't be doing any functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: Fix a few wrong IR keymaps]
Signed-off-by: Shine Liu <shinel@foxmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On certain master / slave dual tuner configurations, tuning performance
improves when the RF tracking filter calibration is performed sequentially.
This patch allows for the bridge driver to specify this behavior in the
configuration structure at attach-time.
The "cal" module option will continue to override this attach-time
configuration: set cal=0 to prevent RF tracking filter calibration
on startup, and set cal=1 to force it.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Reviewed-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
remove excess spacing from the tda_foo printk macros & line things up better
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename dprintk to tda_dprintk to be consistent with the other tda_foo macros.
Move KERN_DEBUG facility level to tda_dprintk.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
KEY_CAMERA is already used for a long time with webcam drivers to take a picture.
On other media drivers, due to the lack of a snapshot button, random KEY codes
were sent, being KEY_SHUFFLE the most used one, probably due to cut-and-paste
from other remotes, since one of them uses the same key for snapshot and shuffle.
The better is to use KEY_CAMERA on all drivers solving this issue. This
follows the IR standard map as defined at:
http://linuxtv.org/wiki/index.php/Remote_Controllers
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use standard definitions for channel controls, as defined at:
http://linuxtv.org/wiki/index.php/Remote_Controllers
While here, fix a few broken up/down/left/right mappings
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Each remote were using a different keycode for timeshift. Use the same
keycode for all of them, using the map as defined at:
http://linuxtv.org/wiki/index.php/Remote_Controllers
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several IR's that were using IR to type a letter that it is
known by some random application. Instead, the better is to use
the standard definitions found at:
http://linuxtv.org/wiki/index.php/Remote_Controllers
And, if needed, submit a patch for the application to understand the
media keys.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While we're still discussing it, let's point to the wiki page. In
the future, this should be added at V4L2 API spec DocBooks.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make Checkpatch tool happy:
-:2349: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
On all cases, it were just a blank line at the wrong place. Yet, fixing it is trivial
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ir-keymaps.c has frequent additions. As people tend to copy an old
keyboard entry, a bad CodingStyle at an ancient entry may result on a
freshly bad CodingStyle patch.
So, better to fix the CodingStyle for the entire file.
This patch is the first of a series of patches fixing it, generated by
some perl magic plus manual handling.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the remote control that comes with the Cinergy Hybrid T USB XS
Thanks to Jelle de Jong for providing sample hardware to test with.
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A user discovered that the Geniatech x8000 encountered a regression when
the xc3028 power management was introduced. The xc3028 never recovers after
setting the powerdown register, which is probably because the xc3028 reset
GPIO is not properly configured. Since I do not have access to the hardware
and thus cannot determine the correct GPIO configuration, just disable xc3028
power management on this board, which fixes the regression.
Thanks to user "ritec" for reporting the issue and testing the fix.
Cc: rictec <rictec@netcabo.pt>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes stack corruption bug present in dump_regs function of zl10353 and
qt1010 drivers: the buffer buf was one byte smaller than required -
there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom
bytes per line and 1 byte for zero ending the string required, i.e. 53
bytes, but only 52 were provided.
The one byte missing in stack based buffer buf can cause stack
corruption possibly leading to kernel oops, as discovered originally
with af9015 driver (af9015: fix stack corruption bug).
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch should fix 7 MHz DVB-T with the XC3028 using the
DTV7 firmware from the xc3028-v27.fw firmware image.
Tested-by: Terry Wu <terrywu2009@gmail.com>
[mchehab@redhat.com: thanks to John Ferlito, we have a real test in Australia]
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an IR profile for the EVGA inDtube remote control (which is an NEC type
remote)
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change order data of buffer in FM simple_tune function. It is usefull for:
1. Set data of tuner with CP bit UP. 0xCE for MK5 or 0xC6 for MK3
2. When call simple_fm_tune, read this byte from config and overwrite
this byte in function simple_radio_bandswitch for set CP bit to OFF.
Of course it can be usefull for other tuner for overwrite default
settings of FM.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both ATSC and DVB @ 6MHz bandwidth require the same offset.
While we're fixing it, let's cleanup the bandwidth setup to better
reflect the fact that it is a function of the bandwidth.
Thanks to Terry Wu <terrywu2009@gmail.com> for pointing this issue and
to Andy Walls <awalls@radix.net> for an initial patch for this fix.
Cc: Terry Wu <terrywu2009@gmail.com>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only two countries that are known to use 6MHz bandwidth are Taiwan
and Uruguay. Both use QAM subcarriers at OFTM.
This patch fixes the firmware load for such countries, where the
required firmware is the QAM one.
This also confirms the previous tests where it was noticed that the 6MHz
QAM firmware doesn't work for cable. So, this patch also removes support
for DVB-C, instead of just printing a warning.
Thanks to Terry Wu <terrywu2009@gmail.com> for pointing this issue and
to Andy Walls <awalls@radix.net> for an initial patch for this fix.
Cc: Terry Wu <terrywu2009@gmail.com>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of polling at 100ms intervals for register writes, poll at 5ms
intervals. This is consistent with the xc5000 specification, and improves
tuning time by up to 500 ms on devices that such as the au0828 which do not
properly implement i2c clock stretching (since the five register writes that
occur for a tuning request often do not complete immediately but do complete
far before 100ms has gone by).
The net amount of time we wait before timing out is unchanged (500ms).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds XC5000 supports for DVB-T 6MHz and 8MHz bandwidth.
Signed-off-by: David T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Xceive has graciously allowed us to now freely redistribute the xc5000
firmware, which eliminates the need for users to manually extract the blob
from the Hauppauge driver.
Thanks to Brian Mathews <bmathews@xceive.com> for providing this code
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a typo in the module description for the "no_poweroff" option, where the
help was being associated with the "debug" option instead.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide for the ability for a user to disable putting the tuner to sleep, in
case he doesn't want to incur the cost of reloading the firmware when starting
up his/her application. The module options are intentionally identical to
xc3028.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it a little more obvious in the dmesg output what is going on during
firmware upload. This is more important for boards like the HVR-950q that
take nearly seven seconds to do the upload.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Starting in firmware version 1.1.44, Xceive recommends using the FINERFREQ for
all normal tuning (the doc indicates reg 0x03 should only be used for fast
scanning for channel lock)
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Expose the firmware build number along with the other version info
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Xceive got rid of the XREG_POWER_DOWN register in later firmware revisions.
Their technical support informed me that the correct way to put the tuner
to sleep is to pull the reset pin (but don't reload the firmware).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This switches to a new version of the xc5000 firmware, extracted from the
latest Hauppauge driver. It includes the support for the XREG_BUSY register
(a lack of which was causing tuning to take 3200ms instead of around 300ms).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't sleep for 400ms polling the tuner's lock if in digital mode (since the
xc5000 lock status registers appear to only be reliable in analog mode)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bring back the code that puts the xc5000 to sleep. For the Pinnacle 801e
this results in power consumption at idle dropping from 325ma to 124ma.
If there are *actually* any devices that don't work in this configuration,
they should set dvb_frontend.ops.tuner_ops.sleep to NULL (per mkrufky's
suggestion)
Also, had to make sure we were making sure the firmware was loaded in the
digital version of set_params, or else we end up get i2c errors if the
device is asleep
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make return value checking for calls to i2c routines explicit.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cleanup the i2c write routine, getting rid of a passthrough function with only
one caller
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch centralizes the i2c read functions, and eliminates pass-through
function only called by one caller.
Make reading of xc5000 registers an atomic i2c transaction in case we're on a
multi-master bus.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the physical device rather than the i2c adapter as the reference
device when loading firmwares. This will prevent the sysfs name
collision with i2c-dev that has been reported many times.
I may have missed other drivers which need the same fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We're going to remove the FIRMWARE_NAME_MAX definition in order to avoid any
firmware name length restriction.
This patch gets rid of the xc2028 FIRMWARE_NAME_MAX reference.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Michel Ludwig <michel.ludwig@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
The v4l2-ioctl core now only allows buffer types for which the
corresponding ->vidioc_try_fmt_xxx() methods are defined to be used with
vidioc_(g|s)_parm.
The driver was only allowing VIDEO_CAPTURE buffers for g_parm, but since
the driver defines ->vidioc_try_fmt_vid_overlay() it will now allow
VIDEO_OVERLAY buffers as well. This should be fine as the fields the
driver fills in, readbuffers and frame rate, aren't wrong for VIDEO_OVERLAY
buffers.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Separate tuning table for DVB-C solves tuning problem at 388MHz
TechnoTrend C-1501 DVB-C card does not lock on 388MHz. I assume that
existing frequency table is valid for DVB-T.
This is suggested by the name of the table: tda827xa_dvbt.
Added a table for DVB-C with the name tda827xa_dvbc.
Added runtime selection of the DVB-C table when the tuner is type
FE_QAM.
This should leave the behaviour of this driver with with DVB_T tuners
unchanged. This modification is in file tda827x.c
The tda827x.c gives the following warning message when debug=1:
tda827x: tda827x_config not defined, cannot set LNA gain!
Solved this by adding a tda827x_config struct in budget-ci.c.
Signed-off-by: Klaas de Waal <klaas.de.waal@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several Kconfig items using CUSTOMIZE. Yet, most use the English
writing CUSTOMISE. This generates lots of trouble, because people sometimes type
the Kbuild item different.
Let's standardise every occurrence using the same syntax.
The changes were generated by this small shell script:
for i in `find linux -type f`; do sed s,CUSTOMIZE,CUSTOMISE,g $i >/tmp/a && mv /tmp/a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc5000 driver has a bug where the IF is always set to whatever the first
caller to dvb_attach() provides. This fails when the device requires an IF
other than 5380 and the analog driver is loaded first through tuner-core
(which always supplies the hard-coded value of 5380).
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tda827x driver supports a feature that the tda18271 driver was lacking
until now. This patch adds support for device-level configuration via the
tuner callback configuration interface.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vidioc_enum_fmt_vid_overlay() did nothing but call
vidioc_enum_fmt_vid_cap(), so just make
saa7146_video_ioctl_ops.vidioc_enum_fmt_vid_overlay point to
vidioc_enum_fmt_vid_cap() and get ride of vidioc_enum_fmt_vid_overlay().
Have gparm use v4l2_video_std_frame_period to fill in the frame period
instead of just assuming PAL.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
report TUNER_STATUS_LOCKED if rf_locked or ref_locked
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function does not work properly and is not necessary - remove it for now.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Analog doesn't work in this driver yet. This code just adds extra bloat,
so remove it for now.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver infrared remote code part is altered to switch to a work queue.
Also ir_codes table moved to ir-common module for shared access.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added support for I2C device at address 0x40 and subaddress 0x0d/0x0b
that provides remote control key reading support for AVerMedia Cardbus
Hybrid card, possibly for other AVerMedia Cardbus cards.
The I2C address 0x40 doesn't like the SAA7134's 0xfd quirk, so it was
disabled.
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Oldřich Jedlička <oldium.pro@seznam.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With while (i++ < 10) { ... } i can reach 11, so callibration still
succeeds at i == 10.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Kaiomy entry.
Thanks to Peter Senna Tschudin <peter.senna@gmail.com> for borrow me one
of those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While here, be sure that gate will be kept disabled if an error occurs.
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The gate control logic is broken: several routines just keep it open;
other rotines close it properly; there are even other routines that
assumes that it is open without really checking or opening it.
Instead of having to manually handle the gate control and having such
troubles, let a sub-routine take care of the gate, opening it before
i2c_transfer and closing it after that. This avoids leaving the gate
into a random state.
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Doing the v4l2_device registration in the saa7146 core will make it
dependent on v4l2, even for DVB-only boards. This registration and
unregistration belongs in saa7146_vv instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modified mxb to load the i2c modules through v4l2_subdev. So no more probing.
Modified tea6415c and tea6420 to use the standard routing ops to do the
routing, rather than using private commands. Dropped the private commands
from tda9840 (they were never used except during initialization of the
module).
Added saa7146 support for VIDIOC_DBG_G_CHIP_IDENT.
Converted saa5246a and saa5249 to v4l2_subdev.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous conversion to video_ioctl2 broke VIDIOC_ENUMSTD. This
is now fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The conversion to video_ioctl2 is the first phase to converting this driver
to the latest v4l2 framework.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by David Engel <david@istwok.net>, ATSC115 doesn't work
fine with mythtv. This software opens both analog and dvb interfaces of
saa7134.
What happens is that some tuner commands are going to the wrong place,
as shown at the logs:
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: using tuner params #0 (ntsc)
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808
Feb 12 20:37:48 opus kernel: tuner 1-0061: tv freq set to 67.25
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: using tuner params #0 (ntsc)
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: tv 0x07 0x10 0xce 0x01
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: tv 0x07 0x10 0xce 0x01
This happens due to a hack at TUV1236D analog setup, where it replaces
tuner address, at 0x61 for 0x0a, in order to save a few memory bytes.
The code assumes that nobody else would try to access the tuner during
that setup, but the point is that there's no lock to protect such
access. So, this opens the possibility of race conditions to happen.
Instead of hacking tuner address, this patch uses a temporary var with
the proper tuner value to be used during the setup. This should save
the issue, although we should consider to write some analog/digital
lock at saa7134 driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The default case of the switch didn't unlock the mutex.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't call tda8290_init_tuner unless we have either a TDA8275 or TDA8275A
present. Calling this function will cause a TDA18271 to get sick, so we
should only call it when needed.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
