Optimize call routing between NATed endpoints: when an external
registrar sends a media description that contains an existing RTP
expectation from a different SNATed connection, the gatekeeper
is trying to route the call directly between the two endpoints.
We assume both endpoints can reach each other directly and
"un-NAT" the addresses, which makes the media stream go between
the two endpoints directly.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for multiple media channels and use it to create
expectations for video streams when present.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SDP connection addresses may be contained in the payload multiple
times (in the session description and/or once per media description),
currently only the session description is properly updated. Split up
SDP mangling so the function setting up expectations only updates the
media port, update connection addresses from media descriptions while
parsing them and at the end update the session description when the
final addresses are known.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create expectations for the RTCP connections in addition to RTP connections.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Media streams can come from anywhere, add a module parameter which
controls whether wildcard expectations or expectations between the
two signalling endpoints are created.
Since the same media description sent on multiple connections may
results in multiple identical expections when using a wildcard source,
we need to check whether a similar expectation already exists for a
different connection before attempting to register it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create expectations for incoming signalling connections when seeing
a REGISTER request. This is needed when the registrar uses a
different source port number for signalling messages and for receiving
incoming calls from other endpoints than the registrar.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SIP message may contain multiple Contact: addresses referring to
the NATed endpoint, translate all of them.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update maddr=, received= and rport= Via-header parameters refering to
the signalling connection.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce URI and header parameter parsing helpers. These are needed
by the conntrack helper to parse expiration values in Contact: header
parameters and by the NAT helper to properly update the Via-header
rport=, received= and maddr= parameters.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flush the RTP expectations we've created when a call is hung up or
terminated otherwise.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform NAT last after parsing the packet. This makes no difference
currently, but is needed when dealing with registrations to make
sure we seen the unNATed addresses.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for per-method request/response handlers and perform SDP
parsing for INVITE/UPDATE requests and for all informational and
successful responses.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the URI parsing helper to get the numerical addresses and get rid of the
text based header translation.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper function to parse a SIP-URI in a header value, optionally
iterating through all headers of this kind.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new function for SIP header parsing that properly deals with
continuation lines and whitespace in headers and use it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The request URI is not a header and needs to be treated differently than
real SIP headers. Add a seperate function for parsing it and get rid of
the POS_REQ_URI/POS_REG_REQ_URI definitions.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
SDP and SIP headers are quite different, SIP can have continuation lines,
leading and trailing whitespace after the colon and is mostly case-insensitive
while SDP headers always begin on a new line and are followed by an equal
sign and the value, without any whitespace.
Introduce new SDP header parsing function and convert all users that used
the SIP header parsing function. This will allow to properly deal with the
special SIP cases in the SIP header parsing function later.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace sizeof/memcmp by strlen/strcmp. Use case-insensitive comparison
for SIP methods and the SIP/2.0 string, as specified in RFC 3261.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conntrack reference and ctinfo can be derived from the packet.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After mangling the packet, the pointer to the data and the length of the data
portion may change and need to be adjusted.
Use double data pointers and a pointer to the length everywhere and add a
helper function to the NAT helper for performing the adjustments.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PHY m88e1111 (not sure about other models, but think they too)
works in two modes: fiber and copper. In Marvell PHY driver (that we
have in current community kernels) code supported only copper mode,
and this is not configurable, bits for copper mode are simply written
in registers during PHY initialization.
This patch adds support for both modes.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't count rx dropped packets based on return value of netif_receive_skb(),
which is misleading.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
o eliminate tx lock in netxen adapter struct, instead pound on netdev
tx lock appropriately.
o remove old "concurrent transmit" code that unnecessarily drops and
reacquires tx lock in hard_xmit_frame(), this is already serialized
the netdev xmit lock.
o reduce scope of tx lock in tx cleanup. tx cleanup operates on
different section of the ring than transmitting cpus and is
guarded by producer and consumer indices. This fixes a race
caused by rx softirq preemption on realtime kernels.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
o separate and simpler irq handler for msi interrupts, avoids few checks
than legacy mode.
o avoid redudant tx_has_work() and rx_has_work() checks in interrupt
and napi, which can uncork irq based on racy (lockless) access to tx
and rx ring indices. If we get interrupt, there's sufficient reason to
schedule napi.
o replenish rx ring more often, remove self-imposed threshold rcv_free
that prevents posting rx desc to card. This improves performance in
low memory.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recent netxen firmware has new scheme of generating MSI interrupts, it
raises interrupt and blocks itself, waiting for driver to unmask. This
reduces chance of spurious interrupts.
The driver will be able to deal with older firmware as well.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Tested-by: Vernon Mauery <mauery@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Deepak Saxena <dsaxena@plexity.net>
Cc: Nicolas Pitre <nico@cam.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The variable num_group_tail_writes is initialized but never used otherwise.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
identifier i;
constant C;
@@
(
extern T i;
|
- T i;
<+... when != i
- i = C;
...+>
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For bonding interfaces any attempt to read the sysfs directory contents after
module removal results in an oops. The fix is to release sysfs attributes
for the interfaces upon module unload.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix two compiler warnings that are new with recent versions of gcc
(apparently 4.2 and up). One is fixed by refactoring; this change was
supplied by Stephen Hemminger. The other was fixed by labelling the
variable as uninitialized_var() after confirming via inspection that it
cannot actually be used uninitialized.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 802.3ad state machine lock can be acquired in both softirq and
not softirq context, but was not held at _bh to prevent a deadlock (which
could occur if a LACPDU arrived and was processed while the lock was
held).
Corrected this, now hold the state machine lock at _bh to prevent
deadlock.
Bug reported by Todd Fleisher <todd@fleish.org>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch to drivers/net/tokenring/smctr.c fixes a "bitwise vs
logical" or error.
Signed-off-by: Jay Schulist <jjschlst@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
"limit" marks the first character outside the bounds.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to set up the destination NAT mapping before the source NAT
mapping, so the NAT core gets to see the final tuple and can decide
whether the source port needs to be remapped.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce expectation classes and policies. An expectation class
is used to distinguish different types of expectations by the
same helper (for example audio/video/t.120). The expectation
policy is used to hold the maximum number of expectations and
the initial timeout for each class.
The individual classes are isolated from each other, which means
that for example an audio expectation will only evict other audio
expectations.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is useful for the SIP helper and signalling expectations.
We don't want to create a full-blown expectation with a wildcard
as source based on a single UDP packet, but need to know the
final port anyways. With inactive expectations we can register
the expectation and reserve the tuple, but wait for confirmation
from the registrar before activating it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_CT_TUPLE_DUMP prints IPv4 addresses as IPv6, fix this and use printk
(guarded by #ifdef DEBUG) directly instead of pr_debug since the tuple
is usually printed at the end of line and we don't want to include a
log-level.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With nf_conntrack DUMP_TUPLE got renamed to NF_CT_DUMP_TUPLE, fix
CLUSTERIP to use the proper macro name.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt73usb and rt2500usb used in_atomic to determine
if a configuration step should be rescheduled or not.
Since in_atomic() is not a valid method to determine
if sleeping is allowed we should fix the way this is handled
by adding a new flag to rt2x00.
In addition mark LED class support for the drivers broken
since that also uses the broken in_atomic() method but
so far no solution exists to have LED triggers work only
in scheduled context.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
