A crash upon booting that is caused by bcm43xx has been reported [1] and
found to be due to a work queue being reinitialized while work on that
queue is still pending. This fix modifies the shutdown of work queues and
prevents periodic work from being requeued during shutdown. With this patch,
no more crashes on reboot were observed by the original reporter. I do not
get that particular failure on my system; however, when running a large
number of ifdown/ifup sequences, my system would kernel panic with the
'caps lock' light blinking at roughly a 1 Hz rate. In addition, there were
infrequent failures in the firmware that resulted in 'IRQ READY TIMEOUT'
errors. With this patch, no more of the first type of failure occur, and
incidence of the second type is greatly reduced.
[1] http://bugzilla.kernel.org/show_bug.cgi?id=8937
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CONFIG_BCM947XX configuration variable was designed for use by the
embedded device used by the OpenWRT project. The device has been shifted
to the ssb driver in bcm43xx-mac80211 and will not be used with SoftMAC.
Accordingly, this "dead" configuration variable is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes various bugs in the init and shutdown code
that would lead to lockups and crashes.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrite of the bcm43xx initialization routines.
This fixes several issues:
* up-down-up-down-up... stale data issue
(May fix some DHCP issues)
* Fix the init vs IRQ handler race (and remove the workaround)
* Fix init for cards with multiple cores (APHY)
As softmac has no internal PHY handling (unlike dscape),
this adds the file "phymode" to sysfs.
The active PHY can be selected by writing either a, b or g
to this file. Current PHY can be determined by reading from it.
* Fix the controller restart code.
Controller restart can now also be triggered through
echo 1 > /debug/bcm43xx/ethX/restart
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current version of bcm43xx-softmac uses local routines to check
if a channel is valid. As noted in the comments, these routines do
not take any regulatory information into account. This patch converts
the code to use the equivalent routine in ieee80211, which is being
converted to know about regulatory information.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem here is that the bcm34xx driver and the ieee80211
stack do not agree on what channels are possible for 802.11a.
The ieee80211 stack only wants channels between 34 and 165, while
the bcm43xx driver accepts anything from 0 to 200. I made the
bcm43xx driver comply with the ieee80211 stack expectations, by
using the proper constants.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
[mb]: Reduce stack usage by kzalloc-ing ieee80211_geo
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Import the bcm43xx driver from the upstream sources here:
ftp://ftp.berlios.de/pub/bcm43xx/snapshots/bcm43xx/bcm43xx-20060123.tar.bz2
Signed-off-by: John W. Linville <linville@tuxdriver.com>
