Commit Graph

154492 Commits

Author SHA1 Message Date
Herbert Xu
d23e43658a tun: Fix device unregister race
It is currently possible for an asynchronous device unregister
to cause the same tun device to be unregistered twice.  This
is because the unregister in tun_chr_close only checks whether
__tun_get(tfile) != NULL.  This however has nothing to do with
whether the device has already been unregistered.  All it tells
you is whether __tun_detach has been called.

This patch fixes this by using the most obvious thing to test
whether the device has been unregistered.

It also moves __tun_detach outside of rtnl_unlock since nothing
that it does requires that lock.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05 18:03:18 -07:00
Sathya Perla
c001c213b1 be2net: fix spurious interrupt handling in intx mode
Occasionally we may see an interrupt without an event in the eq.
In intx, we currently see the event queue and return IRQ_NONE causing
a the irq to be disabled ("no one cared".) Instead, read the CEV_ISR
reg to check the existence of the interrupt.

Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 20:09:45 -07:00
Bruce Allan
7d3cabbcc8 e1000e: disable K1 at 1000Mbps for 82577/82578
This workaround is required for an issue in hardware where noise on the
interconnect between the MAC and PHY could be generated by a lower power
mode (K1) at 1000Mbps resulting in bad packets.  Disable K1 while at 1000
Mbps but keep it enabled for 10/100Mbps and when the cable is disconnected.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 20:09:42 -07:00
Bruce Allan
906e8d9792 e1000e: delay second read of PHY_STATUS register on failure of first read
Some PHYs may require two reads of the PHY_STATUS register to determine the
link status.  If the PHY is being accessed by another thread it is possible
the first read could timeout and fail.  In this case, put a delay in so
the second read will pick up the correct link status.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 20:09:39 -07:00
Bruce Allan
28c9195a57 e1000e: prevent NVM corruption on sectors larger than 4K
Limit NVM writes to 4K sections to prevent NVM corruption on larger
sector allocations (up to 64K).

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 20:09:35 -07:00
Bruce Allan
60f1292fcb e1000e: do not write SmartSpeed register bits on parts without support
The driver was accessing register bits for features on parts that do
not support that feature.  This could cause problems in the hardware.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 20:09:32 -07:00
Bruce Allan
fc0c7760ae e1000e: delay after LCD reset and proper checks for PHY configuration done
A previous workaround for 82578 to avoid link stall causes some PHY
registers to get cleared inadvertently.  Add a delay after all LCD resets
to make sure PHY registers are in a stable state before continuing.  Also,
after resets check the EEC register for the state of PHY configuration
performed by the MAC for ICH9 and earlier parts (as done before), but check
the LAN_INIT_DONE bit in the STATUS register for ICH10 and newer parts (EEC
doesn't exist in these newer parts).

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 20:09:29 -07:00
Bruce Allan
e65fa87c22 e1000e: PHY loopback broken on 82578
PHY loopback on 82578 fails to work as a result of flushing the packets
in the FIFO buffer in the link stall workaround.  Don't perform the
workaround if in PHY loopback mode.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 20:09:27 -07:00
Mallikarjuna R Chilakala
e5d57af524 ixgbe: Not allow 8259x unsupported wol options change from ethtool
Wake-on-lan is currently only supported by 82599 KX4 devices, in all
other cases return a proper value from ixgbe_wol_exclusion function call.
Otherwise from ethtool we will be able to change wol options of
unsupported 8259x devices.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:11:11 -07:00
Don Skidmore
5da43c1a78 ixgbe: fix inconsistent SFP/SFP+ failure results.
Currently if we loaded the driver, insert an unsupported module, and then
attempt to "ifconfig up" the device it will be brought down but the netdev
would not be unregistered. This behavior is different than all other
code paths. This patch corrects that by down'ing the device and then
scheduling the sfp_config_module_task tasklet. The tasklet will detect
this condition (like it does with other code paths) and do the
unregister_netdev().

I also removed the log message as this condition (an unsupported SFP+
module) will be logged in sfp_config_module_task.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:11:05 -07:00
Don Skidmore
19343de279 ixgbe: fix regression on some 82598 adapters
The change to check the SFP+ module again on open() was
causing the XFP (non-SFP+) adapters to be rejected. We
only want to try and re-identify the SFP+ module if the
original probe found that this device was an SFP+ device.
So for this code path (driver loaded with SFP module, module
inserted, ifconfig up of the device) the type will be
ixgbe_phy_unknown for an unidentified SFP+ module.  So we
only check if that is the case.

This problem also shows up on Copper devices.

Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:11:00 -07:00
Don Skidmore
63d6e1d80a ixgbe: fix issues with failing to detect insert of unsupported module
Several small fixes around negative test case of the insertion of a
IXGBE_ERR_NOT_SUPPORTED module.

- mdio45_probe call was always failing due to mdio.prtad not being
set.  The function set to mdio.mdio_read was still working as we just
happen to always be at prtad == 0.  This will allow us to set the phy_id
and phy.type correctly now.

- There was timing issue with i2c calls when initiated from a tasklet.
A small delay was added to allow the electrical oscillation to calm down.

- Logic change in ixgbe_sfp_task that allows NOT_SUPPORTED condition
to be recognized.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:55 -07:00
Ron Mercer
e332471c03 qlge: Fix sizeof usage.
Some usage was only sizing a pointer rather than the data type.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:51 -07:00
Ron Mercer
6a47330892 qlge: Add/use function for link up/down.
We need to set/clear the mac address register when the link goes up/down
respectively.  Without this both ports of a 2-port device can end up
with the same mac address in a bonding scenario.
The new ql_link_on() and ql_link_off() will also be used in handling
certain firmware events.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:46 -07:00
Ron Mercer
7fab3bfe08 qlge: Fix MAC address bonding issue.
This addes functionality to set/clear the MAC address in the hardware
when the link goes up/down.
The MAC address register is persistent across function resets. In
bonding the same address can bounce from one port to the other.  This
can cause packets to be delivered to the wrong port.
This patch clears the MAC address in the hardware when the link is down
and sets it when the link comes up.
It was found that pulling/pushing the cable from one port to another
causes the same MAC address to be in both ports.
The next patch in this series will use this functionality as well.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:41 -07:00
Ron Mercer
13cfd5be53 qlge: Fix tx byte counter.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:37 -07:00
Ron Mercer
6e9e4795e6 qlge: Fix redundant call to free resources.
The caller will free acquired resouces if a failure occurs.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:30 -07:00
Ron Mercer
8b007de190 qlge: Fix carrier on condition.
We were turning on the carrier without verifying the link was up.
This adds link up to the link initialize check before turning carrier
on.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:26 -07:00
Ron Mercer
a5f59dc926 qlge: Clear frame to queue routing before reset.
Not clearing the routing bits can cause frames to erroneously get routed to
management processor.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:21 -07:00
Ron Mercer
4322c5bee8 qlge: Expand coverage of hw lock for config register.
The hardware semaphore covers the configuration register as well as the
ICB registers.  The ICB high and low regs contain the address of the
initialization control block and the config register is used to signal
the hardware that a block is ready to be downloaded.  Currently we were
only protecting the ICB regs.  This changes expands to cover the config
register as well.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:18 -07:00
Brian Haley
a1ed05263b IPv6: preferred lifetime of address not getting updated
There's a bug in addrconf_prefix_rcv() where it won't update the
preferred lifetime of an IPv6 address if the current valid lifetime
of the address is less than 2 hours (the minimum value in the RA).

For example, If I send a router advertisement with a prefix that
has valid lifetime = preferred lifetime = 2 hours we'll build
this address:

3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
    inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic
       valid_lft 7175sec preferred_lft 7175sec

If I then send the same prefix with valid lifetime = preferred
lifetime = 0 it will be ignored since the minimum valid lifetime
is 2 hours:

3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
    inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic
       valid_lft 7161sec preferred_lft 7161sec

But according to RFC 4862 we should always reset the preferred lifetime
even if the valid lifetime is invalid, which would cause the address
to immediately get deprecated.  So with this patch we'd see this:

5: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
    inet6 2001:1890:1109:a20:21f:29ff:fe5a:ef04/64 scope global deprecated dynamic
       valid_lft 7163sec preferred_lft 0sec

The comment winds-up being 5x the size of the code to fix the problem.

Update the preferred lifetime of IPv6 addresses derived from a prefix
info option in a router advertisement even if the valid lifetime in
the option is invalid, as specified in RFC 4862 Section 5.5.3e.  Fixes
an issue where an address will not immediately become deprecated.
Reported by Jens Rosenboom.

Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:13 -07:00
Wei Yongjun
59cae0092e xfrm6: fix the proto and ports decode of sctp protocol
The SCTP pushed the skb above the sctp chunk header, so the
check of pskb_may_pull(skb, nh + offset + 1 - skb->data) in
_decode_session6() will never return 0 and the ports decode
of sctp will always fail. (nh + offset + 1 - skb->data < 0)

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:10 -07:00
Wei Yongjun
c615c9f3f3 xfrm4: fix the ports decode of sctp protocol
The SCTP pushed the skb data above the sctp chunk header, so the check
of pskb_may_pull(skb, xprth + 4 - skb->data) in _decode_session4() will
never return 0 because xprth + 4 - skb->data < 0, the ports decode of
sctp will always fail.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:06 -07:00
Abhishek Kulkarni
15da4b1612 net/9p: Fix crash due to bad mount parameters.
It is not safe to use match_int without checking the token type returned
by match_token (especially when the token type returned is Opt_err and
args is empty). Fix it.

Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-02 13:17:01 -07:00
Alexander Duyck
887b5ea368 if_ether: add define for 1588 aka Timesync
This patch adds ETH_P_1588 protocol ID define.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-02 13:16:58 -07:00
Wade Farnsworth
42caa07404 phylib: fixes for PHY_RESUMING state changes
The PHY_HALTED state disables phydev->link, but the link will not be
updated upon entering PHY_RESUMING.  Add a call to phy_read_status() to
update the link before entering PHY_RUNNING.  If the link is not up at
this point, enter the PHY_NOLINK state instead.

Also, when transitioning from PHY_RESUMING to PHY_RUNNING, calls to
netif_carrier_on() and phydev->adjust_link() are missing.  Add the calls
similar to the other transitions to PHY_RUNNING.

Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-02 13:16:55 -07:00
Dhananjay Phadke
67c38fc61a netxen: avoid frequent firmware reset
Restrict firmware reset to following cases -

o chip rev is NX2031 (firmare doesn't support heartbit).
o firmware is dead.
o previous attempt to init firmware had failed.
o we have got newer file firmware.

This speeds up module load tremendously (by upto 8 sec),
also avoids downtime for NCSI (management) pass-thru
traffic.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-02 13:16:51 -07:00
Dhananjay Phadke
98e31bb009 netxen: fix the version code macro
Correct firmware encoding is 8 bit major, 8 bit minor and
16 bit subversion. Flash has sizes rightly set, but original
driver submission messed it leaving 16 bit major and 8 bit
subversion.

Also fix a infinite loop when cut-thru file firmware is
invalid.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-02 13:16:49 -07:00
Tilman Schmidt
c56bd0c39c gigaset: drop pointless check
Drop a sanity check which doesn't serve any useful purpose anymore.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-02 13:16:46 -07:00
Tilman Schmidt
bceb0f126f gigaset: accept connection establishment messages in any order
ISDN connection setup failed if the "connection active" and
"B channel up" messages from the device arrived in a different
order than expected. Modify the state machine to accept them in
any order.

Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-02 13:16:41 -07:00
Joe Perches
3f1f7cf08d netfilter: add netfilter git to MAINTAINERS
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
2009-07-01 11:32:10 +02:00
Eric W. Biederman
f8a68e752b Revert "ipv4: arp announce, arp_proxy and windows ip conflict verification"
This reverts commit 73ce7b01b4.

After discovering that we don't listen to gratuitious arps in 2.6.30
I tracked the failure down to this commit.

The patch makes absolutely no sense.  RFC2131 RFC3927 and RFC5227.
are all in agreement that an arp request with sip == 0 should be used
for the probe (to prevent learning) and an arp request with sip == tip
should be used for the gratitous announcement that people can learn
from.

It appears the author of the broken patch got those two cases confused
and modified the code to drop all gratuitous arp traffic.  Ouch!

Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:47:08 -07:00
Alexander Duyck
59ed6eecff igb: return PCI_ERS_RESULT_DISCONNECT on permanent error
PCI drivers that implement the io_error_detected callback should return
PCI_ERS_RESULT_DISCONNECT if the state passed in is
pci_channel_io_perm_failure.  This patch fixes the issue for igb.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:47:04 -07:00
Mike Mason
c93b5a76d5 e1000e: io_error_detected callback should return PCI_ERS_RESULT_DISCONNECT
on permanent failure

PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure.  This state is not
checked in many of the network drivers.

This patch fixes the omission in the e1000e driver.

Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:47:02 -07:00
Andre Detsch
eab633021c e1000: return PCI_ERS_RESULT_DISCONNECT on permanent error
PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure.  This state is
not checked in many of the network drivers.

The patch fixes the omission in the e1000 driver.

Based on Mike Mason's similar patch for e1000e.

Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
CC: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:47:00 -07:00
Jesse Brandeburg
679be3ba0c e1000: fix unmap bug
as reported by kerneloops.org

[  121.781161] ------------[ cut here ]------------
[  121.781171] WARNING: at lib/dma-debug.c:793 check_unmap+0x14e/0x577()
[  121.781173] Hardware name: S5520HC
[  121.781177] e1000 0000:0a:00.0: DMA-API: device driver tries to free DMA
memory it has not allocated [device address=0x00000001d688b0fa] [size=1522
bytes]
[  121.781180] Modules linked in: e1000 mdio  dca [last unloaded: ixgbe]
[  121.781187] Pid: 4793, comm: bash Tainted: P 2.6.30-master-06161113 #3
[  121.781190] Call Trace:
[  121.781195]  [<ffffffff8123056f>] ? check_unmap+0x14e/0x577
[  121.781201]  [<ffffffff81057a19>] warn_slowpath_common+0x77/0x8f
[  121.781205]  [<ffffffff81057ae1>] warn_slowpath_fmt+0x9f/0xa1
[  121.781212]  [<ffffffff81477ce2>] ? _spin_lock_irqsave+0x3f/0x49
[  121.781216]  [<ffffffff8122fa97>] ? get_hash_bucket+0x28/0x33
[  121.781220]  [<ffffffff8123056f>] check_unmap+0x14e/0x577
[  121.781225]  [<ffffffff810e4f48>] ? check_bytes_and_report+0x38/0xcb
[  121.781230]  [<ffffffff81230bbf>] debug_dma_unmap_page+0x80/0x92
[  121.781234]  [<ffffffff8122e549>] ? unmap_single+0x1a/0x4e
[  121.781239]  [<ffffffff813901e1>] ? __kfree_skb+0x74/0x78
[  121.781250]  [<ffffffffa00662ef>] pci_unmap_single+0x64/0x6d [e1000]
[  121.781259]  [<ffffffffa0066344>] e1000_clean_rx_ring+0x4c/0xbf [e1000]
[  121.781268]  [<ffffffffa00663df>] e1000_clean_all_rx_rings+0x28/0x36 [e1000]
[  121.781277]  [<ffffffffa0067464>] e1000_down+0x138/0x141 [e1000]
[  121.781286]  [<ffffffffa00681c2>] __e1000_shutdown+0x6b/0x198 [e1000]
[  121.781296]  [<ffffffffa0068405>] e1000_suspend+0x17/0x50 [e1000]
[  121.781301]  [<ffffffff81237665>] pci_legacy_suspend+0x3b/0xbe
[  121.781305]  [<ffffffff81237bc6>] pci_pm_suspend+0x3e/0xf1
[  121.781310]  [<ffffffff812eaf1c>] pm_op+0x57/0xde
[  121.781314]  [<ffffffff812eb444>] dpm_suspend_start+0x31e/0x470
[  121.781319]  [<ffffffff810877da>] suspend_devices_and_enter+0x3e/0x1a2
[  121.781323]  [<ffffffff81087a0f>] enter_state+0xd1/0x127
[  121.781327]  [<ffffffff8108717a>] state_store+0xa7/0xc9
[  121.781332]  [<ffffffff81221843>] kobj_attr_store+0x17/0x19
[  121.781336]  [<ffffffff8113c01e>] sysfs_write_file+0xe5/0x121
[  121.781341]  [<ffffffff810ed165>] vfs_write+0xab/0x105
[  121.781344]  [<ffffffff810ed279>] sys_write+0x47/0x6d
[  121.781349]  [<ffffffff81027aab>] system_call_fastpath+0x16/0x1b
[  121.781352] ---[ end trace 97bacaaac2ed7786 ]---

Fix is to correctly zero out internal ->dma value when unmapping
and make sure never to unmap unless there specifically was a mapping done.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:58 -07:00
Jesse Brandeburg
91615f765a igb: fix unmap length bug
driver was mixing NET_IP_ALIGN count bytes in map/unmap calls
unevenly. Only map the bytes that the hardware might dma into

also fix unmap related bug where ->dma was not being cleared
after unmap

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:57 -07:00
Jesse Brandeburg
4f57ca6e17 ixgbe: fix unmap length bug
This patch addresses three WARN_ON statements from DMA-API debug code

ixgbe is mapping more than it unmaps, reduce the length of the map call and
remove the "used once" local variable.

found by Joerg Roedel <joerg.roedel@amd.com> in 2.6.30, so is a candidate
for -stable.

in addition, fix missing ->dma = 0 after unmap to prevent double free with
pci_unmap_single

and lastly, don't unmap (half) pages that aren't mapped.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:54 -07:00
Mallikarjuna R Chilakala
a1f25324b9 ixgbe: Fix link capabilities during adapter resets
Adapter link advertisement capabilities were not persistent during
adapter resets. While configuring multispeed fiber link check for
phy autoneg_advertised settings before overwriting with default
link capabilities

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:53 -07:00
Mallikarjuna R Chilakala
a380137900 ixgbe: Fix device capabilities of 82599 single speed fiber NICs.
82599 single speed fiber modules only support 10G/Full. Return
proper device capabilities while querrying the adapter and error
while changing device advertisement/speed/duplex capabilities.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:53 -07:00
Don Skidmore
88d2b81f4e ixgbe: Fix SFP log messages
We had a wide range of log messages for the same sort of SFP
failure.  This patch makes them all more similar and less
confusing along with converting them to dev_err.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:51 -07:00
Herbert Xu
d9d62f3f2c usbnet: Remove private stats structure
Now that nothing uses the private stats structure we can remove it.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:49 -07:00
Herbert Xu
7963837f93 usbnet: Use netdev stats structure
Now that netdev has its own stats structure we should use that
instead.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:48 -07:00
Herbert Xu
80667ac13a smsc95xx: Use netdev stats structure
Now that netdev has its own stats structure we should use that
instead.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:46 -07:00
Herbert Xu
58e2e7d591 rndis_host: Use netdev stats structure
Now that netdev has its own stats structure we should use that
instead.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:45 -07:00
Herbert Xu
a22d2b36a2 net1080: Use netdev stats structure
Now that netdev has its own stats structure we should use that
instead.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:43 -07:00
Herbert Xu
9612101cb3 dm9601: Use netdev stats structure
Now that netdev has its own stats structure we should use that
instead.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:43 -07:00
Herbert Xu
eaea43abf3 cdc_eem: Use netdev stats structure
Now that netdev has its own stats structure we should use that
instead.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:41 -07:00
Jarek Poplawski
008440e3ad ipv4: Fix fib_trie rebalancing, part 3
Alas current delaying of freeing old tnodes by RCU in trie_rebalance
is still not enough because we can free a top tnode before updating a
t->trie pointer.

Reported-by: Pawel Staszewski <pstaszewski@itcare.pl>
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 12:48:38 -07:00
Naohiro Ooiwa
01e5329814 bnx2x: Fix the behavior of ethtool when ONBOOT=no
This is the same fix as commit
7959ea254e ("bnx2: Fix the behavior of
ethtool when ONBOOT=no"), but for bnx2x:

--------------------
    When configure in ifcfg-eth* is ONBOOT=no,
    the behavior of ethtool command is wrong.
    
        # grep ONBOOT /etc/sysconfig/network-scripts/ifcfg-eth2
        ONBOOT=no
        # ethtool eth2 | tail -n1
                Link detected: yes
    
    I think "Link detected" should be "no".
--------------------

Signed-off-by: Naohiro Ooiwa <nooiwa@miraclelinux.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 12:44:19 -07:00