This may happen e.g. when the ssb is statically enables by the b44 driver,
and the b43 pci-ssb bridge is enbled by the b43/b43legacy drivers, or the
b43/b43legacy drivers are built statically.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bridge code was unnecessary enabled by the b44
driver, but it prevents the bcm43xx driver from
being loaded, as the bridge claims the same pci ids.
Now we enable the birdge only if the b43{legacy}
drivers are selected.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas driver exports a number of symbols with no in-tree users;
remove these unused exports. lbs_reset_device() is completely unused, with
no callers at all, so remove the function completely.
A couple of these unused exported symbols are static, which causes the
following build error on ia64 with gcc 4.2.3:
drivers/net/wireless/libertas/main.c:1375: error: __ksymtab_lbs_remove_mesh causes a section type conflict
drivers/net/wireless/libertas/main.c:1354: error: __ksymtab_lbs_add_mesh causes a section type conflict
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib_reset_link_tuner() can be called from within
the link tuner itself. This means that it should
_not_ call rt2x00lib_stop_link_tuner() since that will
cause the thread to hang.
Reorder the things that should be done during a
link tuner reset and during a link tuner start.
Also make antenna tuning the last step of the link
tuner since it could possibly reset some statistical
information which we need for average calculation.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rssi_a > rssi_b is true and the current antenna
was already antenna A, then rt2x00 incorrectly jumped
to antenna B.
Also don't configure the antenna when there has been
no change in the antenna setup.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds 2 new states which both are used to toggle
the RX. These new states are required for usage
inside the link tuner thread, because the normal
RX toggling will stop the link tuner thread.
While it is possible that the link tuner thread itself
is the caller of the RX toggle (when using software
antenna diversity).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix 2 issues in antenna diversity selection.
1) the following statement will always return true.
if ((rssi_curr - rssi_old) > -5 || (rssi_curr - rssi_old) < 5)
It is cleaner to check if the absolute value is smaller then 5.
2) Only enable software diversity when default antenna setup
indicates support for it. Don't select it when the hardware
does not indicate support for it...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
| CC drivers/net/ps3_gelic_wireless.o
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c: In function 'gelic_wl_setup_netdev_ops':
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2660: error: 'struct net_device' has no member named 'wireless_data'
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2661: error: 'struct net_device' has no member named 'wireless_handlers'
| make[3]: *** [drivers/net/ps3_gelic_wireless.o] Error 1
| make[2]: *** [drivers/net] Error 2
| make[1]: *** [drivers] Error 2
| make[1]: *** Waiting for unfinished jobs....
| make: *** [sub-make] Error 2
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Acked-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Link the net_device structure of the wireless part to the
corresponding device structure.
Without this, the sysfs node for this net_device would not have
'device' link.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is obviously wrong to use an enum in a little endian struct,
and those other enums should be declared differently.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the macvlan release I had at least 5 users asking how to configure
it since the old userspace tool doesn't work with the version in the
kernel. Add a pointer to the Kconfig help.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some spelling errors and inconsistencies in comment blocks.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this patch avoids a denial of service from an evildoer sending a
continuous stream of flow control at our adapter that is plugged
into a non-flow control enabled switch.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This simplifies the 82571/2/3 family initialization a bit
and removes an initialization table no longer needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This counter is valuable to determine if the system is unable
to timely return buffers to the hardware and this counter starts
to increase well before the hardware starts to drop packets. If
users experience rx_no_buffer_count increasing, they should increase
the amount of descriptors. That will provide more buffers for the
hardware and will decrease the chance of hard drops.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix NCFGR.SPD setting on 10Mbps. This bug was introduced by
conversion to generic PHY layer in kernel 2.6.23.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix problems in LED management, so ethtool -p works correctly on Yukon-EC
and other chips. The driver was incorrectly setting the PHY LED overide bits.
Moral: read the spec sheet, not the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use register offset definition for WOLcgClr, rather than a magic
number.
This patch does not change the driver behaviour.
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a check-after-use spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch eliminates a kernel panic with the igb driver in 2.6.25-rc2 when
running on a Intel 82575 Ethernet controller with a 1000BASE-SX PHY. The
panic does not happen with the 1000BASE-T PHY, only with a SX connection.
Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change all dma op invocations in gianfar.c to actually pass in the
device pointer. Currently, the value is ignored, but it will be
used going forward as we implement archdata for 32-bit powerpc.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reading a serie of zero from the cmos sram area do not work
well with is_valid_ether_addr(). Let's read the mac address
from the eeprom first as it seems more reliable.
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=9831
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The forward declarations were already marked static, make the definitions
be static as well. Fixes the sparse warnings as well.
drivers/net/tlan.c:1403:5: warning: symbol 'TLan_HandleInvalid' was not declared. Should it be static?
drivers/net/tlan.c:1435:5: warning: symbol 'TLan_HandleTxEOF' was not declared. Should it be static?
drivers/net/tlan.c:1521:5: warning: symbol 'TLan_HandleStatOverflow' was not declared. Should it be static?
drivers/net/tlan.c:1557:5: warning: symbol 'TLan_HandleRxEOF' was not declared. Should it be static?
drivers/net/tlan.c:1692:5: warning: symbol 'TLan_HandleDummy' was not declared. Should it be static?
drivers/net/tlan.c:1722:5: warning: symbol 'TLan_HandleTxEOC' was not declared. Should it be static?
drivers/net/tlan.c:1770:5: warning: symbol 'TLan_HandleStatusCheck' was not declared. Should it be static?
drivers/net/tlan.c:1845:5: warning: symbol 'TLan_HandleRxEOC' was not declared. Should it be static?
drivers/net/tlan.c:1905:6: warning: symbol 'TLan_Timer' was not declared. Should it be static?
drivers/net/tlan.c:1986:6: warning: symbol 'TLan_ResetLists' was not declared. Should it be static?
drivers/net/tlan.c:2046:6: warning: symbol 'TLan_FreeLists' was not declared. Should it be static?
drivers/net/tlan.c:2095:6: warning: symbol 'TLan_PrintDio' was not declared. Should it be static?
drivers/net/tlan.c:2130:6: warning: symbol 'TLan_PrintList' was not declared. Should it be static?
drivers/net/tlan.c:2166:6: warning: symbol 'TLan_ReadAndClearStats' was not declared. Should it be static?
drivers/net/tlan.c:2242:1: warning: symbol 'TLan_ResetAdapter' was not declared. Should it be static?
drivers/net/tlan.c:2328:1: warning: symbol 'TLan_FinishReset' was not declared. Should it be static?
drivers/net/tlan.c:2451:6: warning: symbol 'TLan_SetMac' was not declared. Should it be static?
drivers/net/tlan.c:2493:6: warning: symbol 'TLan_PhyPrint' was not declared. Should it be static?
drivers/net/tlan.c:2542:6: warning: symbol 'TLan_PhyDetect' was not declared. Should it be static?
drivers/net/tlan.c:2589:6: warning: symbol 'TLan_PhyPowerDown' was not declared. Should it be static?
drivers/net/tlan.c:2614:6: warning: symbol 'TLan_PhyPowerUp' was not declared. Should it be static?
drivers/net/tlan.c:2635:6: warning: symbol 'TLan_PhyReset' was not declared. Should it be static?
drivers/net/tlan.c:2663:6: warning: symbol 'TLan_PhyStartLink' was not declared. Should it be static?
drivers/net/tlan.c:2750:6: warning: symbol 'TLan_PhyFinishAutoNeg' was not declared. Should it be static?
drivers/net/tlan.c:2906:5: warning: symbol 'TLan_MiiReadReg' was not declared. Should it be static?
drivers/net/tlan.c:2996:6: warning: symbol 'TLan_MiiSendData' was not declared. Should it be static?
drivers/net/tlan.c:3038:6: warning: symbol 'TLan_MiiSync' was not declared. Should it be static?
drivers/net/tlan.c:3077:6: warning: symbol 'TLan_MiiWriteReg' was not declared. Should it be static?
drivers/net/tlan.c:3147:6: warning: symbol 'TLan_EeSendStart' was not declared. Should it be static?
drivers/net/tlan.c:3187:5: warning: symbol 'TLan_EeSendByte' was not declared. Should it be static?
drivers/net/tlan.c:3248:6: warning: symbol 'TLan_EeReceiveByte' was not declared. Should it be static?
drivers/net/tlan.c:3306:5: warning: symbol 'TLan_EeReadByte' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* If ConfigBase is 0x03c0 && manfid is (0x0149,0xc1ab),
printk "use axnet_cs instead" message.
Actually, most of the card with manfid(0x0149, 0xc1ab)
use pcnet_cs driver.
* remove entry (0x021b, 0x0202)
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Suppress the warning message about the 'netcard_portlist' defined but not used.
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch fixes:
http://bugzilla.kernel.org/show_bug.cgi?id=5839
Init sequence needs to poll phy until phy reset is complete. This is the
same problem that I fixed in 2002 in tulip driver.
Thanks to manty@manty.net for testing this patch.
Thanks to Pozsar Balazs <pozsy@uhulinux.hu> for posting/testing
a similar patch before:
http://lkml.org/lkml/2006/8/21/45
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I booted an igb kernel with the option pci=nomsi and instantly noticed
that interrupts no longer worked on my igb device. I took a look at the
interrupt initialization and quickly discovered a comment stating:
"DO NOT USE EIAME or IAME in legacy mode"
It seemed a bit odd that bits to enable IAM were being set in legacy
interrupt mode, so I dropped out the following parts and interrupts
began working fine again.
[Updated code flow and a nitpick spelling error --Auke]
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The lock acquisition in fs_ioctl() does not appear to actually be necessary,
and thus is simply removed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds kdump support to the ehea driver. As the firmware doesn't free
resource handles automatically, the driver has to run an as simple as possible
free resource function in case of a crash shutdown. The function iterates over
two arrays freeing all resource handles which are stored there. The arrays are
kept up-to-date during normal runtime. The crash handler fn is triggered by the
recently introduced PPC crash shutdown reg/unreg functions.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When asked to blink LEDs the tg3 driver behaves when using:
ethtool -p ethX
The default value for data is zero, and other drivers interpret this
as blink forever (or at least a really long time). The tg3 driver
interprets this as blink once. All drivers should have the same
behaviour.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of some board issues, we need to disable parallel detect on
an HP blade. Without this patch, the link state can become stuck
when it goes into parallel detect mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patches to workaround the 5706S on an HP blade were not
sufficient. The link state still does not change properly in some
cases. This patch adds polling to make it completely reliable.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This silences sparse when run on zd1211rw.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This silences a few sparse warnings. There are two more where
I can't follow the code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'u64' is not necessarily 'unsigned long long'
drivers/net/wireless/ath5k/base.c: In function 'ath5k_beacon_update_timers':
drivers/net/wireless/ath5k/base.c:2130: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
drivers/net/wireless/ath5k/base.c:2130: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
drivers/net/wireless/ath5k/base.c: In function 'ath5k_intr':
drivers/net/wireless/ath5k/base.c:2391: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse sees int -> bool cast as an error:
hw.c:3754:10: warning: cast truncates bits from constant value (ffffffea becomes 0)
Fix it by converting the rettype to int and check appropriately.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Omitted lock causes sparse warning
drivers/net/wireless/ath5k/base.c:1682:1: warning: context imbalance in 'ath5k_tasklet_rx' - different lock contexts for basic block
Add the lock to the guilty fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on report from Cavan Carroll <cavancarroll@hotmail.com>:
http://bugzilla.kernel.org/show_bug.cgi?id=9863
Cc: Cavan Carroll <cavancarroll@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When deleting the veth driver, veth_close calls netif_carrier_off
for the two extremities of the network device. netif_carrier_off on
the peer device will fire an event and hold a reference on the peer
device. Just after, the peer is unregistered taking the rtnl_lock while
the linkwatch_event is scheduled. If __linkwatch_run_queue does not
occurs before the unregistering, unregister_netdevice will wait for
the dev refcount to reach zero holding the rtnl_lock and linkwatch_event
will wait for the rtnl_lock and hold the dev refcount.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Matheos Worku <Matheos.Worku@Sun.COM>
1) niu_enable_alt_mac() needs to be adjusted so that the mask
is computed properly for the BMAC case.
2) BMAC has 6 alt MAC addresses available, not 7.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (60 commits)
[NIU]: Bump driver version and release date.
[NIU]: Fix BMAC alternate MAC address indexing.
net: fix kernel-doc warnings in header files
[IPV6]: Use BUG_ON instead of if + BUG in fib6_del_route.
[IPV6]: dst_entry leak in ip4ip6_err. (resend)
bluetooth: do not move child device other than rfcomm
bluetooth: put hci dev after del conn
[NET]: Elminate spurious print_mac() calls.
[BLUETOOTH] hci_sysfs.c: Kill build warning.
[NET]: Remove MAC_FMT
net/8021q/vlan_dev.c: Use print_mac.
[XFRM]: Fix ordering issue in xfrm_dst_hash_transfer().
[BLUETOOTH] net/bluetooth/hci_core.c: Use time_* macros
[IPV6]: Fix hardcoded removing of old module code
[NETLABEL]: Move some initialization code into __init section.
[NETLABEL]: Shrink the genl-ops registration code.
[AX25] ax25_out: check skb for NULL in ax25_kick()
[TCP]: Fix tcp_v4_send_synack() comment
[IPV4]: fix alignment of IP-Config output
Documentation: fix tcp.txt
...
